固定化单宁对酒类营养成分的吸附性能研究

采用固定化单宁对酒中可能存在的营养成分蛋白质、氨基酸、糖类、有机酸、乙醇和铁离子等进行吸咐试验。结果表明：固定化单宁对不同营养成分的吸附率差别明显，它通过氢键和疏水作用对蛋白质有较大的吸附率，通过多个酚羟基与中心铁离子形成螯合物而对其有较大的吸附率，对氨基酸、糖、有机酸和乙醇等营养成分或风味物质吸附率不大，固定化单宁可以作为一种较为理想的酒类处理剂。     

光学系统光阑应用的实例

介绍了一种光学组合系统，通过构造光学系统虚拟的视场光阑实现人眼屈光度测量，它是光学系统光阑应用的生动实例.     

Richards模型在蔬菜生长预测中的应用

本文从 Richards模型的数学表达出发 ,阐述了模型中各参数初始值的确定以及优化过程 .并利用菜花和菠菜的试验数据建立其“最优”生长模型 .     

带调和势的超临界非线性Schrdinger方程的最佳门槛

考虑带调和势的超临界非线性Schroedinger方程，解决了该方程整体解和爆破解存在所依赖的初始条件的最佳分界门槛．通过构造两类强制变分问题和建立局部不变半流，运用势井方法和凹方法，获得了该方程在两个不同的空间中的整体解和爆破解的最佳门槛条件．     

光致折射效应中空间电荷场建立过程的研究

本文推导了包含自衍射及非线性吸收影响、用以描述空间电荷场建立过程的微分方程组,阐明了周期性的空间电荷场与光强干涉条纹之间的相位差在建立过程中所起的作用,并推导了描述条纹倾斜和弯曲的微分方程。通过数值计算找到了硅酸铋(BSO)晶体中能量转移的规律,讨论了材料特性对过程快慢的影响,提出了用CW激光来探讨瞬态过程快慢的可能性。     

三维随机Ising模型的亚稳态性(Ⅱ)

讨论三维格点环面上随机Ising模型当温度趋向零时的亚稳态性,确定从自旋全为-1的组态到自旋全为+1的组态的最大似然路径和临界组态,并计算出从自旋全为-1的组态出发首次到达自旋全为+1的组态的首达时间的渐近对数估计。证明利用一族带指数扰动的Markov链的大偏差估计。     

Effects of Post-Thermal Treatment on Quality of SiC Grown by PVT Method

We report the effects of post-thermal treatment on the quality of 2-inch 6H-SiC wafer cut from a crystal boule grown by physical vapour transportation method. The full widths at half maximum of x-ray diffraction rocking curves measured on sites across the 2-inch wafer become narrower, indicating the quality improvement after a three-step post-thermal treatment. It is found that the most common defects such as micropipes and inclusions can be significantly reduced after the treatment. Our results show that the post-thermal treatment is an effective route to improve the quality of SiC single crystals.     

�˻����/ͭ�ȵȾ�ѹ��ɢ���ӽ����Ӱ��

As the ITER first wall Be/CuCrZr hot isostatic pressing (HIP) bonding intermediate transition layer, Ti/Cu layer can form a multi-layer intermediate metal phase, and defects such as cracks occur between the Ti/Cu metal phases. CuCrZr was used instead of Be, and a number of CuCrZr/Ti/Cu/CuCrZr joints were fabricated by the same HIP process as Be/CuCrZr to analyze the Ti/Cu joints. The effects of stress relief annealing on joint strength and defect distribution of the joints unannealed, annealed at 400°C and 500°C respectively were studied. The results show that three layers of Ti/Cu diffusion layers are formed on both sides of the intermediate titanium layer, namely Cu₄Ti, CuTi and CuTi₂. The thickness of Cu₄Ti on the pure copper side is thicker than that on the CuCrZr side, so that the crack is almost entirely distributed at the junction of Cu₄Ti and CuTi on the pure copper side where brittle fracture is easy to occur in the tensile samples. As the annealing temperature increases, the generation and propagation of cracks decreases.     

不同倾角的脉管制冷机内自然对流影响的研究

本文通过对脉管内自然对流的数值模拟，讨论了当脉管冷端处在不同方向时，脉管内的自然对流对脉管制冷机性能的影响．数值模拟结果表明，当冷端在下时获得的制冷温度最低；当热端在下并与重力方向成３０°时制冷温度最高．结论与实验测量结果定性一致．所做的理论分析对实现脉管制冷机的良好运行有指导意义。     

高密度氩气的原子间相互作用与状态方程

本文从高密度气体的原子间相互作用出发进行思考,在修改范德瓦耳方程的基础上,提出了一种新的适用于高密度气体的状态方程,并用以对氩气临界区的等温压缩线进行计算,结果与实验值很符合.