Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.     

A power-driven multiplication instruction-set design method for ASIPs

This paper presents a novel power-driven multiplication instruction-set design method for application-specific instruction-set processors (ASIPs). Based on a dual-and-configurable-multiplier structure, our proposed method devises a multiplication instruction set for low-power ASIPs. Our method exploits the execution sequences of multiplication instructions and effective bit widths of variables to reduce power consumed by redundant multiplication bits while minimizing the multiplication execution time. Experimental results on a set of DSP programs demonstrate that our proposed method achieves significant power reduction (up to 18.53%) and execution time improvement (up to 10.43%) with 18% area overhead.     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

Knowledge-based control and case-based diagnosis based upon empirical knowledge and fuzzy logic for the SBR plant.

Because biological wastewater treatment plants (WWTPs) involve a long time-delay and various disturbances, in general, skilled operators manually control the plant based on empirical knowledge. And operators usually diagnose the plant using similar cases experienced in the past. For the effective management of the plant, system automation has to be accomplished based upon operating recipes. This paper introduces automatic control and diagnosis based upon the operator's knowledge. Fuzzy logic was employed to design this knowledge-based controller because fuzzy logic can convert the linguistic information to rules. The controller can manage the influent and external carbon in considering the loading rate. The input of the controller is not the loading rate but the dissolved oxygen (DO) lag-time, which has a strong relation to the loading rate. This approach can replace an expensive sensor, which measures the loading rate and ammonia concentration in the reactor, with a cheaper DO sensor. The proposed controller can assure optimal operation and prevent the over-feeding problem. Case-based diagnosis was achieved by the analysis of profile patterns collected from the past. A new test profile was diagnosed by comparing it with template patterns containing normal and abnormal cases. The proposed control and diagnostic system will guarantee the effective and stable operation of WWTPs.     

Photocatalytic oxidation of low concentration 2,4-D solution with new TiO2 fiber catalyst in a continuous flow reactor.

Environmental pollution by low concentrations of 2,4-Dichlorophenoxyacetic acid (2,4-D) is a concern these days due to ever increasingly stringent regulations. Photocatalysis with immobilized TiO2 fiber is a promising oxidation method. Laboratory experiments on photocatalytic degradation of 0.045 mmol l(-1) 2,4-D with the world's first high-strength TiO2 fiber catalyst were carried out in a continuous flow reactor in which the degradations were, in general, similar to those with high 2,4-D concentrations investigated elsewhere. Degradation and mineralization of 2,4-D were significantly enhanced with no initial pH adjustments. The rate constants for total organic carbon (TOC) without pH adjustment were about two-fold bigger than the pH adjustment cases. CO2 gas measurement and carbon mass-balance were carried out for the first time, where about 34% organic carbon converted into CO2 gas during four-hour oxidation. 2,4-Dichlorophenol (2,4-DCP), phenol, benzyl alcohol and two unknowns (RT = 2.65 and 3.78 min.) were detected as aromatic intermediates while Phenol was the new aromatic in HPLC analysis. Dechlorination efficiencies were high (> 70%) in all the cases, and more than 90% efficiencies were observed in chloride mass balance. Bigger flow rates and solution temperature fixed at 20 degrees C without pH adjustment greatly enhanced 2,4-D mineralization. These results can be an important basis in applying the treatment method for dioxin-contaminated water and wastewater.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

Dominant rock properties affecting the performance of conical picks and the comparison of some experimental and theoretical results

Conical picks are the essential cutting tools used especially on roadheaders, continuous miners and shearers and their cutting performance affects directly the efficiency and the cost of rock/mineral excavation. In this study, in order to better understand the effects of dominant rock properties on cutter performance, 22 different rock specimens having compressive strength values varying from 10 to 170 MPa are first subjected to a wide range of mechanical tests. Then, laboratory full-scale linear cutting tests with different depth of cut and cutter spacing values are realized on large blocks of rock specimens using one type of conical pick. Specific energy, cutting and normal force values for relieved and unrelieved cutting modes are recorded using a triaxial force dynamometer with capacity of 50 tonnes and a data acquisition system. Cutter force and specific energy values are correlated with rock properties and theoretical force and specific energy values obtained from widely used theoretical approaches.The results indicate that uniaxial compressive strength among the rock properties investigated is best correlated with the measured cutter performance values, which is in good agreement with previous studies. However, it is also emphasized in this study that Brazilian tensile strength, Schmidt hammer rebound values, static and dynamic elasticity modulus are also dominant rock properties affecting cutter performance.Theoretical specific energy defined by different researchers has a meaningful relationship with the experimental specific energy, which is an essential parameter for predicting the instantaneous cutting rates of mechanical excavation systems. It is also demonstrated that the experimental cutter forces obtained for 5 mm depth of cut are in good agreement with theoretical force values, if the friction angle between rock and cutting tool is included in the theoretical formulation. It is emphasized that, to some extend, laboratory tests can help to minimize high cost of a trial–error approach in the field.     

Tri-axial sensors and actuators made of a single piezoelectric cylindrical shell

Electromechanical transducers for sensing and actuating disturbances or vibrations have been used in many fields of applications. There have been transducers of different configuration developed for the unidirectional transduction. This paper demonstrates a single element transducer for tri-axial components made of a piezoelectric cylindrical shell. The separation of the tri-axial transductions is achieved by devising a proper electrode arrangement. The structure and the fundamental idea are first presented, and then the numerical analysis by means of the finite element modeling follows, and their characteristics and behaviors are then experimentally verified.