Preparation of fluoroacrylate nanocopolymer by miniemulsion polymerization used in textile finishing

Latex based on fluoroacrylate (TAN) and other comonomers was prepared via miniemulsion polymerization in the presence of stearyl trimethyl ammonium chloride (STAC) and 2, 2′‐azobis (2‐amidinopropane) dihydrochloride (ABAP) as a water soluble initiator. Light transmittance studies demonstrated that the light transmittance of prepared emulsions increases with the amount of TAN, STAC, cosolvent DPM, and hydrophobe DM. Given suitable reaction temperature and quantities of TAN, STAC, DPM, and DM, a copolymer emulsion of fluoroacylate with a particle size of 50 nm was produced. The water repellency tested on polyester fabrics displayed greater effectiveness than that of commercial products with higher fluorine content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1466–1472, 2004     

负载奈米银之二氧化钛光触媒及其光催化活性之研究

利用自制之奈米银粒子,或用化学还原法将银微粒直接沉淀在市售二氧化钛粉末上,并比较二者对亚甲基蓝光催化效果,由于银微粒可降低电子与电洞对再结合之效果,而使二氧化钛粒子光催化活性提高,其中并以直接沉淀法为佳.此外亦藉由高温氢气对二氧化钛粉末进行还原,形成部分的Ti3+,藉此亦达到提升光催化之效果.最后将奈米银负载于经还原过后之二氧化钛粒子,于紫外光与可见光下对酚作光催化分解,发现其亦得到一定程度的分解效果.     

Elastic Response and Effect of Transverse Cracking in Woven Fabric Brittle Matrix Composites

This paper examines the linear elastic tensile and fracture behavior of biaxial plain weave SiC/SiC ceramic woven fabric composites. Iso-phase mode and random-phase mode have been adopted to simulate multilayer stacking and to predict the initial linear elastic constants. It has been found that both modes predict very close results. Porosities in the composite affect the stiffness significantly, while fiber undulation shows only minimal effect. The nonlinear stress-strain relation of the composite is due to transverse cracks, which initiate mainly from interyarn pores. In the second part of this paper, two methods, classical fracture mechanics and energy balance approach, have been used to examine the crack initiation and growth. A finite element method and a modified shear-lag method have been developed to evaluate the stress distribution in the yarn with transverse cracks. The composite stiffness reduction due to transverse cracking has been obtained by both the finite element and shear-lag methods. Strain energy release rates of the growth of transverse cracks have been studied by the crack-closure procedure, using finite element methods. Effects of the yarn size and crack position on the strain energy release rate have been quantified. It is concluded that thinner yarns lead to higher critical strains for transverse cracking.     

Paired electrooxidation IV. Decarboxylation of sodium gluconate to D-arabinose

A paired electrooxidative method has been developed to synthesize D-arabinose in a divided cell. D-arabinose is a material which has an important role in the production of vitamin B2 and DNA. Sodium gluconate was directly oxidized at the anode and indirectly oxidized in the catholyte by bubbling oxygen which was reduced to H₂O₂ and OH free radicals. In the catholyte, indirect oxidation of sodium gluconate was mediated by Fe³⁺ and OH free radicals. The optimal current efficiencies for D-arabinose production in the anolyte and catholyte were found to be 88.37% and 39.12%, respectively, and the total current efficiency of the paired electrooxidation was 127.49%. The paired electrosynthesis of D-arabinose is more economical in terms of power consumption than electrosynthesis that employ a single anode or cathode as the working electrode. The influence of cathodic/anodic CV and I/E curves, redox mediators and the amount of charge passed were also examined.     

Evaluation of two cooling systems under a firefighter coverall

Firemen often suffer from heat strain. This study investigated two chest cooling systems for use under a firefighting suit. In nine male subjects, a vest with water soaked cooling pads and a vest with water perfused tubes were compared to a control condition. Subjects performed 30 min walking and 10 min recovery in hot conditions, while physiological and perceptual parameters were measured. No differences were observed in heart rate and rectal temperature, but scapular skin temperature and fluid loss were lower using the perfused vest. Thermal sensation was cooler for the perfused vest than for the other conditions, while the cool pad vest felt initially cooler than control. However, comfort and RPE scores were similar. We conclude that the cooling effect of both tested systems, mainly providing a (temporally) cooler thermal sensation, was limited and did not meet the expectations.     

羟基磷灰石/β-磷酸三钙/海藻酸钠复合多孔支架的制备与研究

本文讨论了羟基磷灰石/β-磷酸三钙/海藻酸钠(HAP/β-TCP/AG)多孔支架的制备,并通过电子显微镜观察了其微观结构、研究其干细胞亲和性和生物相容性。研究表明:该多孔支架具有三维连通网状结构,干细胞在支架上黏附、生长良好,具有良好的干细胞亲和性和生物相容性。     

Effect of La/K A-site Substitutions on the Ordering of Ba(Zn1/3Ta2/3)O3

The 1/3 <111>-type ordering of Ba(Zn_1/3Ta_2/3)O₃ (BZT) can be transformed to 1/2 <111>–type ordering by substituting the La³⁺ cation into the A site. The 1/3 <111> ordering in BZT is shown to be reduced, discontinued, and then replaced by 1/2 <111> ordering, using X–ray diffraction, electron microscopy, and Raman spectroscopy. On the other hand, potassium–substituted BZT only displays a reduction in the degree of ordering.     

Damage Development and Moduli Reductions in Nicalon—Calcium Aluminosilicate Composites under Static Fatigue and Cyclic Fatigue

Unidirectional and cross-ply Nicalon fiber-reinforced calcium aluminosilicate (CAS) glass-ceramic composite specimens were subjected to tension–tension cyclic fatigue and static fatigue loadings. Microcrack densities, longitudinal Young's modulus, and major Poisson's ratio were measured at regular intervals of load cycles and load time. The matrix crack (0° plies) density and transverse crack (90° plies) density increased gradually with fatigue cycles and load time. The crack growth is environmentally driven and depends on the maximum load and time. Young's modulus and Poisson's ratio decreased gradually with fatigue cycles and load time. The saturation crack densities under fatigue loadings were found to be comparable to those under monotonic loading. A matrix crack growth limit strain exists, below which matrix cracks do not grow significantly under fatigue loading. This limit coincides with the matrix crack initiation strain. Linear correlations between crack density and moduli reductions obtained from quasi-static data can predict the moduli reductions under cyclic loading, using experimentally measured crack densities. A logarithmic correlation can predict the Young's modulus reduction in a limited stress range. A fatigue crack growth model is proposed to explain the presence of two distinct regimes of crack growth and Young's modulus reduction.     

Plastic deformation of ZnO thin films through edge and screw dislocation movements

Columnar wurtzite grains were formed in sputtered ZnO thin films deposited on a plastic polyethylene terephthalate substrate. Selected-area diffraction patterns reveal that the columnar grains in the sputtered films present two preferred growth planes, namely, the basal (0002) and prismatic (100) growth planes. The diffraction patterns obtained also confirm that the microstructure of sputtered indium tin oxide thin films is amorphous in nature. Tensile tests indicate that the fracture strain of the ZnO thin film occurs between 1.73% and 2.14%, while the fracture strain of the indium tin oxide thin film occurs between 0.24% and 0.67%. Thus, the fracture toughness of the sputtered ZnO thin film is greater than that of the sputtered indium tin oxide thin film. High-resolution transmission electron microscopic images demonstrate that edge and screw dislocations could be identified in the sputtered ZnO thin films. Moreover, edge and screw dislocation movements may, respectively, be observed in the basal- and prismatic-oriented ZnO columnar grains of the sputtered ZnO thin films. Our results indicate that movements of the edge and screw dislocations in the basal- and prismatic-oriented ZnO columnar grains account for the plastic deformation of the investigated ZnO thin films under tensile stress.     

A new model for evaluating the electrical conductivity of nonferrous slag

Electrical conductivity of molten slag is an important physicochemical property for designing the refining process in electric smelting furnaces.Though conductivities of many slag systems have been measured,the quantitative relationships of conductivity with slag composition and temperature are still very limited.In this article,the Arrhenius law was used to describe the experimental data of conductivities for CaO-MgO-Al2O3-SiO2,CaO-Al2O3-SiO2,CaO-MnO-Al2O3-SiO2,as well as CaO-MgO-MnO-Al2O3-SiO2 systems,and...