Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

Preparation of pillared carbon thin films and their size selective electrical response to organic vapor

Thin films of graphite oxide silylated with octyltrichlorosilane were first prepared and they were further silylated with 3-aminopropyltriethoxysilane. Pillared carbon thin films with an interlayer spacing of 1.7 nm were prepared from the pyrolysis of the resulting thin films. Larger propylene carbonate molecules were not intercalated into them. They showed selective electrical response to electron donating and smaller organic molecules. The increase in the electrical resistance upon exposure to organic molecule seems to be larger for those with larger donor numbers.     

In Situ Observation of Phase Separation of a Barium Borate Melt in a Stable Immiscibility Region under Microgravity

The precipitation of droplets was directly observed on a BaO–B₂O₃ melt in a drop shaft experiment. This is the first time that precipitation of droplets has been observed in a 4.5 s drop test. The melt film of 4BaOz96B₂O₃ (mol%) held on a platinum wire loop was heated above the critical tem-perature to produce uniformity and was cooled down to the phase separation temperature range. Phase separation of the melt was observed directly with a video camera. The IR image of the melt was simultaneously detected with a CCD array and was converted into a two-dimensional thermograph.     

Organic–silicate hybrid catalysts based on various defined structures for Knoevenagel condensation

Two types of organic–inorganic hybrid base catalysts are prepared. Organic-functionalized molecular sieves (OFMSs), particularly “amine-immobilized porous silicates”, are designed based on common idea to immobilize catalytic active sites on silicate surface. Silicate–organic composite materials (SOCMs), such as “ordered porous silicate–quaternary ammonium composite materials”, are the precursors of ordered porous silicates obtained during the synthesis. Both the OFMS and the SOCM are used as the catalysts for Knoevenagel condensation. Among the OFMSs, there is clear tendency that the use of molecular sieve with larger pore volume and/or surface area gives the product in higher yield. Aminopropylsilyl (AP)-functionalized mesoporous silicates such as AP-MCM-41 gives the product in high yield under mild conditions. No loss of activity is observed after repeated use for three times. The SOCMs are also active for the same reaction. The precursors of the mesoporous silicates are more active than those of microporous silicates. This material can be repeatedly used without significant loss of activity. High activity is not due to the leached species. The active sites of the SOCM catalysts are considered to be SiO⁻ moieties located on the pore-mouth. Activity of the SOCM increases when the reaction is carried out without solvent, whereas decrease in activity of the OFMS is observed in the solvent-free system.     

Te concentration dependent photoemission and inverse-photoemission study of FeSe1?xTex

We have characterized the electronic structure of FeSe_1−xTe_x for various x values using soft x-ray photoemission spectroscopy (SXPES), high-resolution photoemission spectroscopy (HRPES) and inverse photoemission spectroscopy (IPES). The SXPES valence band spectral shape shows that the 2 eV feature in FeSe, which was ascribed to the lower Hubbard band in previous theoretical studies, becomes less prominent with increasing x. HRPES exhibits systematic x dependence of the structure near the Fermi level (E_F): its splitting near E_F and filling of the pseudogap in FeSe. IPES shows two features, near E_F and approximately 6 eV above E_F; the former may be related to the Fe 3d states hybridized with chalcogenide p states, while the latter may consist of plane-wave-like and Se d components. In the incident electron energy dependence of IPES, the density of states near E_F for FeSe and FeTe has the Fano lineshape characteristic of resonant behavior. These compounds exhibit different resonance profiles, which may reflect the differences in their electronic structures. By combining the PES and IPES data the on-site Coulomb energy was estimated at 3.5 eV for FeSe.     

Evaluation of environmentally friendly lubricants for cold forging

The authors proposed double-layer-type environmentally friendly lubricants, which were composed of an undercoat, superior in adhering to a material, and an overcoat, superior in reducing the friction between the material and the die. The performance of these lubricants for cold forging was evaluated by the ring compression test, the combined forward rod-backward can extrusion-type friction test and the combined forward conical can-backward straight can extrusion-type friction test. The double-layer-type lubricants showed comparable friction characteristics and anti-pick-up properties to a conversion coating lubricant, when the film thickness and surface treatment before coating were improved. In a practical application by cold multistage forging, the double-layer-type lubricants showed a similar performance to a conversion coating lubricant.     

Mutations Associated with Functional Disorder of Xanthine Oxidoreductase and Hereditary Xanthinuria in Humans

Xanthine oxidoreductase (XOR) catalyzes the conversion of hypoxanthine to xanthine and xanthine to uric acid with concomitant reduction of either NAD⁺ or O₂. The enzyme is a target of drugs to treat hyperuricemia, gout and reactive oxygen-related diseases. Human diseases associated with genetically determined dysfunction of XOR are termed xanthinuria, because of the excretion of xanthine in urine. Xanthinuria is classified into two subtypes, type I and type II. Type I xanthinuria involves XOR deficiency due to genetic defect of XOR, whereas type II xanthinuria involves dual deficiency of XOR and aldehyde oxidase (AO, a molybdoflavo enzyme similar to XOR) due to genetic defect in the molybdenum cofactor sulfurase. Molybdenum cofactor deficiency is associated with triple deficiency of XOR, AO and sulfite oxidase, due to defective synthesis of molybdopterin, which is a precursor of molybdenum cofactor for all three enzymes. The present review focuses on mutation or chemical modification studies of mammalian XOR, as well as on XOR mutations identified in humans, aimed at understanding the reaction mechanism of XOR and the relevance of mutated XORs as models to estimate the possible side effects of clinical application of XOR inhibitors.     

Non-invasive and rapid analysis for observation of internal structure of press-coated tablet using X-ray computed tomography

Background: Since the internal structure of a tablet can be measured without destruction of the sample by X‐ray computed tomography (CT), it could be applied to quality control of tablets during the manufacturing process. Aim: A novel, fast, noninvasive tablet observation method was developed to evaluate the internal structure of commercial press-coated tablets by using X-ray CT. Method: Thirty-two CT image slices of four kinds of commercial press-coated tablets (tablets A, B, C, and D) were measured 300 m interval between edges of the tablet by using an X-ray CT. The thinnest layer thickness of the tablets and distance between centers of gravity (DCG) of tables were calculated. Results: The order of the TLT of the tablets was tablet B > tablet C > tablet D > tablet A. The result indicated that the order of DCG was tablet A > tablet D > tablet C > tablet B. Noninvasive observation of the internal structure of commercial, press-coated tablets by X-ray CT has been demonstrated to be useful in quality control of production. Conclusion: The internal structure of press-coated tablets could be observed without pretreatment, without destruction, and very rapidly by X‐ray CT.     

Electroelastic Response of Cylindrical Fiber with D∞ Symmetry Exposed to Local Electric Field Through Opposed Electrode Pair

To obtain practical information on the electroelastic behavior of poly-l-lactic acid microtweezers or catheters, a previously constructed analytical technique is used to obtain the electroelastic field solution of a poly-l-lactic acid cylindrical fiber exposed to a local electric field, which is applied through an opposed pair of square-sectioned electrodes. The numerical representation of the solution reveals the detailed field quantity distributions, their importance in the design of microtweezers and catheters, the overall deformation of such devices, and the effects of the electrode dimensions on the deformation.