Thermal and Electric Properties in Hot-Pressed ZrB2–MoSi2–SiC Composites

The thermal and electrical properties of MoSi₂ and/or SiC-containing ZrB₂-based composites and the effects of MoSi₂ and SiC contents were examined in hot-pressed ZrB₂–MoSi₂–SiC composites. The thermal conductivity and electrical conductivity of the ZrB₂–MoSi₂–SiC composites were measured at room temperature by a nanoflash technique and a current–voltage method, respectively. The results indicate that the thermal and electrical conductivities of ZrB₂–MoSi₂–SiC composites are dependent on the amount of MoSi₂ and SiC. The thermal conductivities observed for all of the compositions were more than 75 W·(m·K)⁻¹. A maximum conductivity of 97.55 W·(m·K)⁻¹ was measured for the 20 vol% MoSi₂-30 vol% SiC-containing ZrB₂ composite. On the other hand, the electrical conductivities observed for all of the compositions were in the range from 4.07 × 10–8.11 × 10 Ω⁻¹·cm⁻¹.     

基于魏格纳分布的鼓泡流化床中结焦早期诊断

An experimental verification is reported on the early predicting index of agglomeration in bubbling fluidized bed. Coarse quartz sand, which has the same density but larger diameter than the bed material, was used to simulate the initial agglomerated particle. Wigner distribution was used to analyze the pressure fuctuation of the tested bed, and the average amplitude of local domain frequency （LDF） and local peak weighted average frequency （LPWA） under different operating conditions were measured and compared. The results showed that the LDF is sensitive to the agglomeration phenomena and had quick response to the incipient agglomeration in fluidized beds. It can be concluded from the results that these two parameters could be taken as the characteristic indexes to the agglomeration in fuidized beds.     

High thermal conductivity of spark plasma sintered silicon carbide ceramics with yttria and scandia

A fully dense SiC ceramic with a room‐temperature thermal conductivity of 262 W·(m·K)^?1 was obtained via spark plasma sintering β‐SiC powder containing 0.79 vol% Y₂O₃‐Sc₂O₃. High‐resolution transmission electron microscopy revealed two different SiC‐SiC boundaries, that is, amorphous and clean boundaries, in addition to a fully crystallized junction phase. A high thermal conductivity was attributed to a low lattice oxygen content and the presence of clean SiC‐SiC boundaries.     

Antimicrobial susceptibilities of Salmonella isolates obtained from layer chicken houses on a commercial egg-producing farm in Japan, 1997 to 2002

Susceptibility to antimicrobial agents was examined for 325 isolates of Salmonella enterica serotypes Cerro, Infantis, Livingstone, and Montevideo isolated from layer houses on a commercial egg-production farm in the western region of Japan between 1997 and 2002. No antimicrobials were used for therapeutic purposes on the farm during this period. From 1.8 to 3.1% of the isolates were resistant to ampicillin, chloramphenicol, and tetracycline. Resistance to streptomycin and sulfisoxazole was found in 52.9 and 65.5%, respectively, of Salmonella Montevideo isolates and in 0 to 13.2% of the isolates of the other serotypes. All the streptomycin-resistant isolates of Salmonella Montevideo also exhibited resistance to sulfisoxazole. Salmonella Montevideo isolates were first isolated in 1998, and 80.0% of the isolates obtained in this year were resistant to streptomycin and sulfisoxazole. The results suggest that Salmonella Montevideo isolates that had already acquired resistance may have been introduced into the layer houses, although the route and vehicle of transmission were uncertain. The proportion of Salmonella Montevideo isolates resistant to streptomycin and sulfisoxazole significantly decreased (P < 0.01) from 79.5% for 1998 through 1999 to 37.3% for 2000 through 2002. This decrease probably was due to the fact that no antimicrobials were used on the farm. Among 10 isolates from different serotypes obtained from 1997 to 2002 that were resistant to ampicillin, two and five isolates harbored 42- and 63-kb R plasmids and identical DraI restriction enzyme digest patterns, respectively, and carried the blaTEM gene. The results suggest that the ampicillin resistance determinants were transferred among different serotypes of Salmonella in the layer houses.     

Strong Surface‐Termination Effect on Electroresistance in Ferroelectric Tunnel Junctions

Tunnel electroresistance in ferroelectric tunnel junctions (FTJs) has attracted considerable interest, because of a promising application to nonvolatile memories. Development of ferroelectric thin‐film devices requires atomic‐scale band‐structure engineering based on depolarization‐field effects at interfaces. By using FTJs consisting of ultrathin layers of the prototypical ferroelectric BaTiO₃, it is demonstrated that the surface termination of the ferroelectric in contact with a simple‐metal electrode critically affects properties of electroresistance. BaTiO₃ barrier‐layers with TiO₂ or BaO terminations show opposing relationships between the polarization direction and the resistance state. The resistance‐switching ratio in the junctions can be remarkably enhanced up to 10⁵% at room temperature, by artificially controlling the fraction of BaO termination. These results are explained in terms of the termination dependence of the depolarization field that is generated by a dead layer and imperfect charge screening. The findings on the mechanism of tunnel electroresistance should lead to performance improvements in the devices based on nanoscale ferroelectrics.     

A fast method for the determination of the efficiency coefficient of bare CR-39 detector

A fast and simple method for the determination of the efficiency coefficient (η) of bare CR-39 detector is presented and discussed. The efficiency coefficient of bare CR-39 detector is then calculated by different ways and the obtained values are found to be comparable to each other. The average value of η of bare CR-39 is found to be 0.20 ± 0.01 tracks cm⁻² day⁻¹ per Bq m⁻³.     

Accelerated weathering-induced degradation of poly(lactic acid) fiber studied by near-infrared (NIR) hyperspectral imaging

Hydrolysis degradation of a set of drawn poly(lactic acid) (PLA) fibers was induced by an accelerated weathering test, radiating ultraviolet (UV) light under a certain temperature and humidity. The fine features of the transient behavior of the PLA fibers were captured by near-infrared (NIR) hyperspectral imaging. The PLA fibers showed a gradual decrease in mechanical property (e.g., tensile strength), indicating hydrolysis degradation. Thus, the detailed analysis of the spectral variation, in turn, offers useful information on the molecular-level degradation behavior of the drawn PLA fibers. The variation of the spectral intensity as well as band position shift of the crystalline band of PLA was analyzed. The spectral intensity of the crystalline band of PLA showed gradual decrease, suggesting the decrease in molecular weight induced by the hydrolysis degradation. In addition, the crystalline band also exhibited a coinciding shift to the lower wavenumber direction with the weathering test, revealing cleavage-induced crystallization of the PLA samples. Consequently, the hydrolysis degradation induced by the weathering test substantially accelerates predominant degradation of the amorphous structure of the PLA and such variation of the molecular structure, in turn, brings less ductility to the PLA fiber.     

Fabrication of silicon nitride nanoceramics—Powder preparation and sintering: A review

Fine-grained silicon nitride ceramics were investigated mainly for their high-strain-rate plasticity. The preparation and densification of fine silicon nitride powder were reviewed. Commercial sub-micrometer powder was used as raw powder in the “as-received” state and then used after being ground and undergoing classification operation. Chemical vapor deposition and plasma processes were used for fabricating nanopowder because a further reduction in grain size caused by grinding had limitations. More recently, nanopowder has also been obtained by high-energy milling. This process in principle is the same as conventional planetary milling. For densification, primarily hot pressing was performed, although a similar process known as spark plasma sintering (SPS) has also recently been used. One of the advantages of SPS is its high heating rate. The high heating rate is advantageous because it reduces sintering time, achieving densification without grain growth. We prepared silicon nitride nanopowder by high-energy milling and then obtained nanoceramics by densifying the nanopowder by SPS.     

The complex aerodynamic footprint of desert locusts revealed by large-volume tomographic particle image velocimetry

Particle image velocimetry has been the preferred experimental technique with which to study the aerodynamics of animal flight for over a decade. In that time, hardware has become more accessible and the software has progressed from the acquisition of planes through the flow field to the reconstruction of small volumetric measurements. Until now, it has not been possible to capture large volumes that incorporate the full wavelength of the aerodynamic track left behind during a complete wingbeat cycle. Here, we use a unique apparatus to acquire the first instantaneous wake volume of a flying animal''s entire wingbeat. We confirm the presence of wake deformation behind desert locusts and quantify the effect of that deformation on estimates of aerodynamic force and the efficiency of lift generation. We present previously undescribed vortex wake phenomena, including entrainment around the wing-tip vortices of a set of secondary vortices borne of Kelvin–Helmholtz instability in the shear layer behind the flapping wings.