Exponential synchronization of two totally different chaotic systems based on a unified model

This paper presents an exponential synchronization scheme between two chaotic systems with different structures and parameters. A unified model consisting of a linear dynamic system and a bounded static nonlinear operator is employed to describe these totally different chaotic systems. A novel state feedback control law is established to exponentially synchronize the two unified models with different parameters. Most chaotic systems with different structures and parameters, such as Hopfield neural networks, cellular neural networks, Chua’s circuits, unified chaotic systems, Qi systems, and chaotic recurrent multilayer perceptrons, can be transformed into this unified model with the synchronization controller designed in a unified way. Two numerical examples are exploited to illustrate the effectiveness of the proposed design schemes.     

高温浓硫酸用XDS不锈钢板材的研究

根据合金设计的理论，对高温浓硫酸用不锈钢进行全面的改性研究，进而开发出新型耐高温浓硫酸用不锈钢板材XDS。比较并论述了XDS不锈钢在高温浓硫酸中的力学性能和耐腐蚀性能，认为XDS不锈钢已达到国际先进水平，为制造硫酸厂的干吸塔、酸泵等设备提供了优异的钢材，也为低温热回收系统的应用创造了条件。     

Mechanical properties and thermal stability of double‐shell thermal‐energy‐storage microcapsules

Double‐shell‐structured microcapsules encapsulating phase‐change materials (micro‐PCMs) with an average diameter of 5–10 μm were successfully fabricated with a melamine–formaldehyde resin as the coating material. The mechanical properties of the obtained piled micro‐PCMs, tested under compression, were evaluated with a pressure sensor. Typical stress–strain curves showed that both the single‐shell‐ and double‐shell‐structured microcapsules had yield points and maximum point pressures. The morphological changes in the shell surface confirmed the existence of yield points by scanning electron microscopy. When the pressure was beyond the yield point, the microcapsules showed conventional plastic behavior, and the double‐shell structure was more mechanically stable than the single‐shell one. Differential scanning calorimetry analysis results revealed that the properties of the phase‐change materials experienced no variation after coating with a single‐shell‐ or double‐shell‐structured polymer. Thermogravimetric analysis showed that the double‐shell‐structured micro‐PCMs experienced a weight loss of only about 5% from 86.3 to 232°C but did so more rapidly from 232 to 416°C. Thermoregulation was determined with periodical heating and cooling tests. The data showed that the micro‐PCMs changed temperature in a narrow range of 20–25°C with a time lag of 20 min to reach the maximum or minimum temperature in comparison with a reference temperature of 18–28°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1295–1302, 2007     

热处理制度对高ZnO含量的Li2O-Al2O3-SiO2系统玻璃析晶及热膨胀系数的影响

以TiO2 ZrO2 P2O5为复合成核剂,采用传统熔融冷却法获得了高ZnO含量的Li2O-A l2O3-SiO2系统的基础玻璃。通过差热分析确定了该玻璃的热处理条件、晶化性能,利用梯温炉实验、X射线衍射分析和扫描电镜对晶化试样的物相和微观结构进行了研究,讨论了热处理制度对玻璃的析晶及热膨胀系数的影响。研究结果表明:含10%(质量分数)ZnO的LAS系统样品玻璃最佳核化温度为(710±2)℃,玻璃的晶化活化能E为(275±2)kJ/mol,晶化指数n为3.11±0.2,样品玻璃在较低温度下失透,并且随着晶化温度升高,样品的热膨胀系数加大。     

半刚性钢-混凝土组合节点受弯承载力的计算

在半刚性钢 -混凝土组合框架中 ,混凝土板中的纵向钢筋增加了节点的强度和刚度 ,但是 ,传统的设计方法往往忽略纵向钢筋的作用而采用简化的计算模型。因此 ,出于经济效益考虑 ,应该根据半刚性组合节点的实际受力性能建立更加准确的计算方法。这里详细介绍了考虑混凝土板纵向钢筋作用的半刚性组合节点受弯承载力的计算方法 ,计算结果表明 ,建议的公式与试验结果吻合良好 ,可供规范制定和工程应用参考。     

压缩感知中高斯矩阵的优化研究

为了优化高斯矩阵,对部分哈达玛矩阵与高斯矩阵的统计学参数作了对比分析,确定了导致部分哈达玛矩阵信号重构能力好的主要因素,并提出了高斯矩阵优化算法.验证了优化算法对不同规模高斯矩阵的通用性和有效性,确定了优化矩阵对各种稀疏信号重构算法的适用性.最后对优化矩阵的性能作了初步的理论和实验分析,优化矩阵的信号重构能力可达到、甚至超过哈达玛矩阵.研究成果为测量矩阵的分析、设计和优化提供了新的思路和方法.     

PVC-U型材弹性模量测试偏差分析

在对PVC-U型材弹性模量试验中发现，同一样品的规则样条与不规则样条的弯曲弹性模量相差较大。不规则样条的负荷-挠度曲线上会出现拐点，如果不对曲线进行处理直接计算得到的弯曲弹性模量偏小。在不规则样条的负荷-挠度取拐点后直线段切线与横坐标的交点作零点修正后所测得的弯曲弹性模量比较接近真实值。通过实验可以验证处理后的方法测得的弹性模量与均匀规则样条的弯曲弹性模量相近。     

纳米二氧化硅模板的制备

以微乳液法制备纳米二氧化硅（SiO2）粒子，经压制、烧结制备SiO2模板。通过红外（IR）、热分析（TGDTA）、扫描电镜（SEM）等方法对SiO2模板进行表征，结果表明所得SiO2粒度在100nm左右．烧结温度在800℃时，SiO2粒子之间将实现颈长，有利于有机／无机杂化多孔材料的制备。     

PC-DCS关键技术研究

结合一个工控系统实例，介绍了一种PC－DCS系统数据刷新频率的方法，提出从使用智能通信卡，多串口通信，通信数据组织，以及测控仪表选型等全方位着手提高系统通信实时性的新思路。     

CFRP压力容器固化成型过程中边界条件的确定

文中应用总放热系数等效考虑了CFRP压力容器固化过程中热压釜辐射与对流边界条件。将有限元法引入瞬态热传导的反问题，根据试验测量的温度曲线，并结合最优化理论确定合理的热压釜热边界条件。结果表明：平板试验得到了总放热系数序列，其计算温度与测试温度的最大温差为0．147℃。由此，可以将得到的总放热系数序列作为CFRP压力容器固化成型过程的等效热边界条件，为其固化成型的数值模拟提供计算基础。