FM subcarrier fiber optical transmission system design and itsapplication in next-generation wireless access

This paper presents a design method of optical frequency modulation (FM) subcarrier (with super carrier) transmission modem. The nonideal link characteristics, including laser chirping, fiber dispersion, voltage controlled oscillator (VCO) phase noise, relative intensity noise (RIN), and equivalent network model of laser diode of such a system that may bring about signal distortion are discussed first. We then propose a hierarchical methods to establish the system equivalent model. Finally this FM modem is applied to a GSM wireless system, in which multichannel signals are transmitted over fiber between radio port and basestation, and system performance is appraised by its dynamic range. It is found that optical FM subcarrier (with super carrier) transmission technique can improve the system dynamic range, compared with the intensity modulated direct detection (IMDD) method, and this is a economical and efficient method     

Delta opioid peptide [D-Ala2,D-leu5]enkephalin blocks the long-term loss of dopamine transporters induced by multiple administrations of methamphetamine: involvement of opioid receptors and reactive oxygen species

Delta opioid peptide [D-Ala2,D-leu5]enkephalin (DADLE) can prolong organ preservation and increases myocardial tolerance to ischemia. Our study examined the protective property of DADLE against methamphetamine- (METH) induced dopaminergic terminal damage in the central nervous system. Because the neurotoxicity of METH involves reactive oxygen species, we also examined if DADLE might be an antioxidative agent in vitro. DADLE at 2 and 4 mg/kg (i.p.), given 30 min before each METH administration (5 or 10 mg/kg, i.p., four injections in a day at 2-hr intervals), dose-dependently blocked the METH-induced long-term dopamine transporter loss. The opioid antagonist naltrexone blocked this action of DADLE in both aspects of striata but tends not to affect the effects of DADLE in the nucleus accumbens. DADLE did not alter changes in body temperature induced by METH. The reduction of striatal dopaminergic content and tyrosine hydroxylase activity caused by METH, however, were not blocked by DADLE. In vitro, DADLE was approximately equipotent to glutathione in inhibiting both superoxide anion formation induced by xanthine oxidase and hydroxyl radical formation evoked by ferrous/citrate complex. DADLE was only slightly less potent than glutathione in inhibiting the iron/ascorbate-induced brain lipid peroxidation. These results suggest that DADLE can protect the terminal membranes of dopaminergic neurons against METH-induced insult but not the loss of dopaminergic content and tyrosine hydroxylase activity and that this action of DADLE might involve opioid receptors as well as the sequestration of free radical.     

Investigation of fusion reactions in palladium and titanium tritide using galvanostatic,coulometric, and hydrogen permeation techniques

We describe several electrochemical methods used to investigate the possibility of cold fusion phenomena in palladium and titanium tritide cathodes. We performed long-term (up to 77 days) electrolysis experiments with electrochemical cells of the University of Utah type at current densities as high as 1 A/cm², while monitoring neutron and tritium levels. With some cells, we pulsed the current to determine if neutron bursts would result. In another cell, we used titanium tritide as the cathode to determine if D-T reactions yielding neutrons would occur. In no instance were levels of neutrons or tritium significantly above background except in the titanium tritide cell where isotopic exchange, occcurring between the electrode and the electrolyte, resulted in significant tritium levels. We also combined x-ray photoelectron spectroscopy (XPS) and electrochemical hydrogen permeation experiments to determine the effectiveness of various Pd surface treatment procedures on the resultant electrochemical hydrogen absorption efficiency. Electroanalytical and thermal desorption/gas analysis techniques indicated the maximum loading of H in Pd was to a ratio of HPd=0.8.     

A comparison of neutron-induced SEU rates in Si and GaAs devices

The single-event-upset rates due to neutron-induced nuclear recoils have been calculated for Si and GaAs components using the HETC and MCNP codes and the ENDF data base for (n, p) and (n, alpha) reactions. For the same critical charge and sensitive volume, the upset rate in Si exceeds that of GaAs by a factor of about 1.7, mainly because more energy is transferred in neutron interactions with lighter Si nuclei. The upset rates due to neutrons are presented as functions of critical charge and atmospheric altitude. Upsets induced by cosmic-ray nuclei, secondary protons and neutrons are compared.     

Hydrolysis losses in the hydrate desalination process: rate measurements and economic analysis

Hydrolysis of the agents used in the hydrate process for desalination is an irreversible reaction and represents an economic loss chargeable to the cost of the water produced. Rates of this reaction have been measured for the agents CH₂ClF-(F-31), CHCl₂F(F-21), CH₃CClF₂(F-142b), and CH₃Br. Rates for CH₃Cl and CCl₂F₂(F-12) have been found in the literature. An economic analysis of hydrolysis losses for all six agents has been made with the following results: F-21, F-31, F-142b and F-12 are all suitable for use in the hydrate process from the standpoint of hydrolysis; CH₃Br hydrolyses much too rapidly to be economical; CH₃Cl requires additional study with metal catalysts before being certified as useful.     

Effects of special drill bits on drilling-induced delamination of composite materials

Drilling is the most frequently employed operation of secondary machining for fiber-reinforced materials owing to the need for joining structures. Delamination is among the serious concerns during drilling. Practical experience proves the advantage of using such special drills as saw drill, candle stick drill, core drill and step drill. The experimental investigation described in this paper examines the theoretical predictions of critical thrust force at the onset of delamination, and compares the effects of these different drill bits. The results confirm the analytical findings and are consistent with the industrial experience. Ultrasonic scanning is used to evaluate the extent of drilling-induced delamination. The advantage of these special drills is illustrated mathematically as well as experimentally, that their thrust force is distributed toward the drill periphery instead of being concentrated at the center. The allowable feed rate without causing delamination is also increased. The analysis can be extended to examine the effects of other future innovative drill bits.     

Interfacial reactions of liquid Sn and Sn-3.5Ag solders with Ag thick films

The interfacial reactions of liquid Sn and Sn-3.5Ag solders with Ag thick films are investigated in the temperature range from 250–325 °C, and the morphology of intermetallic compounds formed after such soldering reactions is observed. In kinetics analysis of the growths of intermetallic compounds, it was found that both Sn/Ag and Sn-3.5Ag/Ag reactions were interfacial-controlled, and the growth rates for both cases were similar. The rate of Ag dissolution into liquid solder attendant on the formation of interfacial intermetallic compounds after Sn/Ag reaction was about four times higher than that after Sn-3.5Ag/Ag reaction, as evidenced by experimental results.     

Dynamic variable depth of cut machining using piezoelectric actuators

This paper describes the design of a piezoelectric actuated cutting tool and implementation of digital servo controls for machining surfaces with dynamically varying depth of cut. Through a flexure hinge, the tool holder could generate 50 μm travel at the tip of the cutting insert. Tool motion errors of less than 0.5 μm were achieved in tracking cyclic waveforms by employing a digital repetitive servo control. When applied to turning aluminum and steel workpieces with variable depth of cut using carbide tools, less than 5 μm machined surface errors were measured.