Characterization of Failure Mechanisms of Duplex and Graded Thermal Barrier Coatings Exposed to Thermal Shock Test

The beginning of failure of a (ZrO2-7%Y2O3)/(Ni-22%Co-17%Cr-12.5%Al-0.6%Y) duplex andgraded coating systems on lnconel 617 and IN738LC in burner rig tests has been characterized.The test conditions are 40 s heating up to 75O℃ substrate temperature followed by 80 s aircooling. Failure is considered at the appearance of the first bright spot during heating period.Stresses due to thermal expansion mismatch strains on cooling are the probable cause of life-limiting in this conditions of testing.     

Study of Lateral Spread of Ions Emitted from 2.3 kJ Plasma Focus with Hydrogen and Nitrogen Gases

The characteristics of ion beams of hydrogen and nitrogen with different filling pressures emitted from the plasma focus device of 2.3 kJ energy are investigated. CR-39 SSNTDs are employed for the registration of tracks of ions. The exposed detectors are etched in 6N NaOH solution at 70°C and then examined with an optical microscope. The ion flux is estimated to be of the order of 10^5–6 tracks/cm². The flux with the radial position does not exhibit any regular pattern of variation.     

Effect of Zn and Pb as alloying elements on the electrochemical behavior of brass in NaCl solutions

The electrochemical behavior of brasses with various Zn content (5.5–38 mass%) and brass (Cu–38Zn) with different Pb contents (1–3.4 mass%) in 0.6 M NaCl was investigated. The effects of temperature, immersion time, and concentration of chloride ions on the behavior of the different alloys were studied. The pitting corrosion behavior of Cu–Zn alloys and leaded–brass alloys in 0.6 M NaCl solution was also investigated. Open-circuit potential measurements (OCP), polarization techniques and electrochemical impedance spectroscopy (EIS) were used. The results show that the increase in the Zn content increases the corrosion rate of the brass alloys in chloride solutions, while the increase of Pb content in Cu–38Zn–Pb decreases the corrosion rate of the alloy. Long immersion time of the alloys in the aqueous electrolyte improves their stability due to the formation of passive film on the alloy surface. The breakdown potential is shifted to more negative direction with increasing the Zn content, whereas it shifts towards positive values with increasing Pb content. Equivalent circuit model for the electrode/electrolyte interface under different conditions was proposed to illustrate the electrochemical processes taking place at the interface. The electrochemical behavior of the different alloys was discussed in view of the fitting results.     

Epoxy/poly(methyl methacrylate) interpenetrating polymer networks—morphology,mechanical and thermal properties

Full and semi-IPNs were prepared from epoxy and poly methyl methacrylate (PMMA), by the sequential mode of synthesis and were characterized by measurements of ultimate tensile strength (UTS), elongation at break, modulus, and toughness. Aromatic polyamine adducts and ethylene glycol dimethacrylate were used as the crosslinkers for epoxy and comonomer/crosslinker for methyl methacrylate monomer, respectively. Higher UTS and modulus of the semi-IPNs over full IPNs were attributed to the higher probability of interpenetration. The weight retention in the thermal decomposition of the IPNs and semi-IPNs were higher than the epoxy homopolymer. This enhancement was presumably related to the presence of the unzipped methyl methacrylate monomer which acted as radical scavangers in the epoxy degradation. © 1994 John Wiley & Sons, Inc.     

Modeling and evaluating design alternatives for an on-lineinstrumentation system: a case study

This paper demonstrates the use of a model-based evaluation approach for instrumentation systems (ISs). The overall objective of this study is to provide early feedback to tool developers regarding IS overhead and performance; such feedback helps developers make appropriate design decisions about alternative system configurations and task scheduling policies. We consider three types of system architectures: network of workstations (NOW), symmetric multiprocessors (SMP), and massively parallel processing (MPP) systems. We develop a Resource OCCupancy (ROCC) model for an on-line IS for an existing tool and parameterize it for an IBM SP-2 platform. This model is simulated to answer several “what if” questions regarding two policies to schedule instrumentation data forwarding: collect-and-forward (CF) and batch-and-forward (BF). In addition, this study investigates two alternatives for forwarding the instrumentation data: direct and binary tree forwarding for an MPP system. Simulation results indicate that the BF policy can significantly reduce the overhead and that the tree forwarding configuration exhibits desirable scalability characteristics for MPP systems. Initial measurement-based testing results indicate more than 60 percent reduction in the direct IS overhead when the BF policy was added to Paradyn parallel performance measurement tool     

Nanoindentation Creep,Nano-Impact,and Thermal Properties of Multiwall Carbon Nanotubes–Polypropylene Nanocomposites Prepared via Melt Blending

Morphological analysis of the nanocomposites showed that multi-wall carbon nanotubes were uniformly distributed in polypropylene. Nanoindentation creep and nano-impact tests were carried out. Several equations/models were used to analyze creep data. From creep test, hardness of the nanocomposites increased by 18 and 36% for C150P and C70P, respectively, compared to polypropylene, whereas elasticity also increased by 20 and 34%. From nano-impact test, hardness of the nanocomposites was also higher than that of neat polypropylene. However, hardness (dynamic/impact) values were slightly higher than the (quasi-static) hardness resulted from creep test. In addition, degree of crystallinity of nanocomposites also increased by 12.6 and 14.3%.     

Friction and wear of copper/lead and aluminium/tin filled polyamide coatings

The friction and wear of steel pins coated with filled polyamides and loaded against a rotating cylinder of bearing steel were tested under dry, lubricated, and abrasive contaminated conditions. The filler materials were copper/lead and aluminium/tin powders. The test results show a significant reduction in friction with the Cu/Pb filled polyamides (8 wt.% Cu, 12 wt.% Pb, and 80 wt.% PA6). The Al/Sn filled polyamides (3 wt.% Al, 2 wt.% Sn, and 95 wt.% PA6) showed the best wear resistance, accompanied by an increase in the coefficient of friction.     

Corrosion control of Cu-Ni alloys in neutral chloride solutions by amino acids

The corrosion inhibition of Cu-Ni alloys was investigated in aqueous chloride solutions using amino acids as environmentally safe materials. The corrosion rate was calculated in absence and presence of the corrosion inhibitor using polarization and impedance techniques. The inhibition efficiency of the different amino acids was also calculated.The experimental results have shown that a simple amino acid like glycine can be used as efficient corrosion inhibitor for the Cu-Ni alloys in neutral chloride solutions. An inhibition efficiency of about 85% could be achieved at very low concentrations of the amino acid (0.1 mM). For low Ni content alloy (Cu-5Ni), 2.0 mM cysteine shows a remarkable high (∼96%) corrosion inhibition efficiency. The experimental impedance data were fitted to theoretical data according to a proposed equivalent circuit model for the electrode/electrolyte interface, and the mechanism of the corrosion inhibition process was suggested. Different adsorption isotherms were tested and the corrosion inhibition process was found to depend on the adsorption of the amino acid molecules and/or the deposition of corrosion products on the alloy surface. The adsorption free energy of cysteine on Cu-5Ni (−37.81 kJ mol⁻¹) reveals a strong physical adsorption of the inhibitor on the alloy surface.