Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Reducing cycle times in manufacturing and supply chains by input and service rate smoothing

A key performance parameter of a manufacturing network or supply chain is its cycle time; the time that a typical item spends in the network. A previous simulation study on a semiconductor assembly and test facility showed that cycle times could be reduced by having smooth input and service rates. This suggested that there is a “cycle time principle” that, for a system with a specified throughput or input rate, the shortest cycle times are obtained when the input and service rates do not vary over time. We prove that this principle is true for the M/G/1 and M/M/s queueing systems and Jackson networks. The analysis involves establishing several results on the concavity of waiting time probabilities and the convexity of expected waiting times and queue lengths, as functions of input and service rates. These results also have natural uses in other optimization problems.     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

Distributed self-stabilizing placement of replicated resources in emerging networks

Emerging large scale distributed networking systems, such as P2P file sharing systems, sensor networks, and ad hoc wireless networks, require replication of content, functionality, or configuration to enact or optimize communication tasks. The placement of these replicated resources can significantly impact performance. We present a novel self-stabilizing, fully distributed, asynchronous, scalable protocol that can be used to place replicated resources such that each node is "close" to some copy of any object. We describe our protocol in the context of a graph with colored nodes, where a node's color indicates the replica/task that it is assigned. Our combination of theoretical results and simulation prove stabilization of the protocol, and evaluate its performance in the context of convergence time, message transmissions, and color distance. Our results show that the protocol generates colorings that are close to the optimal under a set of metrics, making such a protocol ideal for emerging networking systems.     

Using classification techniques for informal requirements in the requirements analysis-supporting system

In order to efficiently develop large-scale and complicated software, it is important for system engineers to correctly understand users’ requirements. Most requirements in large-scale projects are collected from various stakeholders located in various regions, and they are generally written in natural language. Therefore, the initial collected requirements must be classified into various topics prior to analysis phases in order to be usable as input in several requirements analysis methods. If this classification process is manually done by analysts, it becomes a time-consuming task. To solve this problem, we propose a new bootstrapping method which can automatically classify requirements sentences into each topic category using only topic words as the representative of the analysts’ views. The proposed method is verified through experiments using two requirements data sets: one written in English and the other in Korean. The significant performances were achieved in the experiments: the 84.28 and 87.91 F1 scores for the English and Korean data sets, respectively. As a result, the proposed method can provide an effective function for an Internet-based requirements analysis-supporting system so as to efficiently gather and analyze requirements from various and distributed stakeholders by using the Internet.     

Toughening mechanism for a rubber-toughened epoxy resin with rubber/matrix interfacial modification

For a rubber-toughened piperidine-DGEBA epoxy resin, the interface between the rubber particle and the epoxy resin matrix was modified by an epoxide end-capped carboxyl terminated butadiene and acrylonitrile random copolymer (CTBN). The end-capping epoxides used were a rigid diglycidyl ether of bisphenol-A (Epon 828), a short-chain flexible diglycidyl ether of propylene glycol (DER 736), and a long-chain flexible diglycidyl ether of propylene glycol (DER 732). The microstructures and the fracture behaviour of these rubber-modified epoxy resins were studied by transmission electron microscopy and scanning electron microscopy. Their thermal and mechanical properties were also investigated. In the rubber-modified epoxy resins, if the added CTBNs were end-capped by a flexible diglycidyl ether of propylene glycol (DER 732 or DER 736) before curing, the interfacial zone of the undeformed rubber particle, the degree of cavitation of the cavitated rubber particle on the fracture surface and the fracture energy of the toughened epoxy resin were all significantly increased. The toughening mechanism based on cavitation and localized shear yielding was considered and a mechanism for the interaction between cavitation and localized shear yielding that accounts for all the observed characteristics is proposed.