一维有序聚苯胺纳米阵列的制备及电化学储能性能

以导电玻璃FTO为基底电极, 在硫酸溶液中, 分别研究了苯胺单体浓度和恒定电流大小对聚苯胺(PANI)形貌的影响; 同时恒定苯胺单体的浓度和工作电流, 探究了不同类型的质子酸对PANI阵列形貌的影响. 结果表明, 采用恒电流方法可以制备出一维有序PANI纳米线阵列, 而且当苯胺的浓度为0.1 mol/L, 恒电流法的工作电流密度为0.03 mA/cm²时, 所制备的PANI纳米线阵列形貌最佳; 当用HCl, HNO₃和对甲苯磺酸(p-TSA)作为合成PANI的支持液时, 得到树桩状的PANI 纳米结构, 不能得到均一的纳米线阵列结构. 电化学性能测试结果表明, 制备的最佳形貌PANI纳米线阵列的比电容值可达560 F/g; 循环1000周后电容损失率为11%.     

苯胺在高氯酸溶液中恒电流法电化学聚合研究

本文在对苯胺在高氯酸溶液中电流聚合进行研究，内容包括在铂圆盘电极上影响苯胺电化学聚合的因素，如苯胺及高氯酸浓度，恒电流密度及聚合总电量（Ｑｒ）聚合电位等，实验结果表明，在合适的条件下制得的聚苯腚（ＰＡＮＩ）膜电极，其氧化还原电量（Ｑｔ）和Ｑｒ的比值接近了１００％的并对聚苯胺（ＰＡＮＩ）膜电极的电化学性质进行了探讨。     

由苯胺二聚体电化学制备聚苯胺的形貌可控性初探

以苯胺二聚体（N-phenyl-p-phenylenediamine）为起始单体,在1 mol·L^-1高氯酸水-乙腈混合液中,玻碳电极表面电化学制备聚苯胺. 实验结果表明,苯胺二聚体单体的聚合电位比苯胺单体的低约0.2 V,并且其聚合物具有更高的形貌可控性. 苯胺二聚体单体浓度分别为1、5和10 mmol·L^-1时,采用分步恒电流法可分别制备出形貌均一的聚苯胺纳米粒子（粒径30 nm）、超长的纳米线（> 5 μm 直径50 nm）和大面积纳米片（4 μm × 2 μm × 30 nm）.     

高密度聚苯胺纳米线阵列的制备及在紫外探测器中的应用研究

基于p型半导体与n型半导体间的特殊p-n结效应可有效提高紫外探测器的紫外光敏性能,研究了高密度p型聚苯胺(PANI)纳米线阵列的制备方法,及其与n型单晶硅片组装为具有p-n结效应的高性能紫外探测器的方法.采用旋涂煅烧法在单晶硅片表面制备了二氧化锰层,研究了以其为种子层制备高密度聚苯胺纳米线阵列的方法,并考察了不同制备条件对聚苯胺形貌的影响,揭示了聚苯胺纳米线阵列的形成机理.结果表明,利用二氧化锰种子层对溶液中苯胺的氧化作用,可优先在二氧化锰层表面形成聚苯胺纳米粒子,然后再向溶液中加入另一氧化剂过硫酸铵(APS),可使聚苯胺纳米粒子沿垂直于衬底方向进一步生长,从而制得了分布均匀的高密度p型聚苯胺纳米线阵列.利用p型聚苯胺纳米线阵列与n型单晶硅片间特殊的p-n结效应,构筑了性能优良的紫外探测器,对紫外光响应速度快、恢复时间短、稳定性好.当外置偏压为0 V时,光电流可达9.2×10-8A;且随外置偏压提高,光电流强度大大增强,当外置偏压提高至5 V时,光电流可达3.2×10-5A,比0 V时提高了约1000倍.     

分子筛修饰电极中内电子传输机理的研究

用电化学方法聚合方法筛孔道内的苯胺,以聚苯胺分子筛修饰电极为模型研究了分子筛修饰电极的内电子传输机理,ＮａＹ分子筛的离子交换点位被苯胺修饰后,通过电聚合制得聚苯胺分子筛修饰电极（Ｐａｎ＾＋Ｙ－ＺＭＥ）,该电极通过聚苯胺链自身的电子跳跃来实现电子传输,且只有通过阴极富集后对溶液中Ｃｄ＾２＋才有响应,并能用于测定抗坏血酸。     

电化学合成聚苯胺粉末电极的电化学行为研究

我们曾用慢速动电位扫描法研究化学合成聚苯胺粉末的电化学行为.本文对恒电位电解合成聚苯胺粉末进行了研究.用这种方法制备的粉末由于合成溶液中不含氧化剂因而纯度高.本文还报导了这种聚苯胺粉末电极的交流阻抗测量结果.交流阻抗法曾用于聚苯胺膜的电导和化学合成聚吡咯的电阻测定. 所用盐酸、氟硼酸、硅氟酸、苯胺均为分析纯;苯胺经常压蒸馏提纯;硫酸为超纯;磷酸为分析纯;高氯酸为优级纯.溶液皆用两次蒸馏水配制.     

有机化学接枝-电化学沉积聚合制备CNTs/PANI纳米复合材料

通过有机化学合成法先在碳纳米管表面接枝上苯胺单体,然后在不锈钢电极表面在硫酸溶液中采用循环伏安法电化学沉积聚合制得碳纳米管/聚苯胺(CNTs/PANI)纳米复合材料.扫描电子显微镜和傅立叶变换红外光谱表征所得材料的微观结构和基团,循环伏安和恒流充放电测试用于考察所得CNTs/PANI纳米复合材料的电化学性能.所得结果与...     

微电极研究 ⅩⅢ.聚苯胺修饰微盘电极的研究

用恒电流法在盐酸介质中以最佳聚合条件将聚苯胺修饰在Ｐｔ微盘电极上。制得的聚苯胺修饰微盘电极对ｐＨ有能斯特响应，稳定性好，用于样品测定，结果满意。     

基于碳纸电极电化学快速合成聚苯胺纳米纤维

利用碳纸电极,采用循环伏安法、恒电流法和恒电位法等电化学聚合法快速合成了高氯酸掺杂聚苯胺纳米纤维.利用电子显微镜、红外光谱和四探针测定仪等对聚苯胺的微观形貌结构、掺杂度和电导率进行了研究.用循环伏安法对聚苯胺的电化学特征进行了分析.研究发现,3种方法合成的聚苯胺均为纳米纤维状结构,长度达3μm,直径为50~150 nm.其中,循环伏安法合成的聚苯胺纳米纤维的均一性和电导率均优于其它2种方法,其电导率高达5.97 S/cm.另外,聚苯胺合成速率顺序为恒电流法>循环伏安法>恒电位法,且恒电流法合成的聚苯胺纳米纤维电极材料的放电比容量最大(578 F/g),电容性能最好.     

恒电位条件下制备聚苯胺PAn及其电化学行为

恒电位条件下在玻碳电极上用电化学聚合法制备了聚苯胺膜，研究了聚合条件如聚合电位，聚合介质，苯胺浓度等对聚苯胺膜化学性质的影响，从而确定了制备聚苯胺的最佳聚合方法和条件，并讨论了在不同支持电解质溶液中和不同ＰＨ值条件下ＰＡｎ膜的循环伏安行为，认为５５０ｍＶ出现的氧化还原峰与阴离子的掺杂有关。     

Controlled self-assembly of nanoporous alumina for the self-templating synthesis of polyaniline nanowires

In this report, the self-templating synthesis of polyaniline nanowires on prestructured aluminum is described, emphasizing that anodization and electropolymerization can occur at the same time by a single electrochemical process. The method is based on the principle that the anodization of predefined aluminum in H₂SO₄ leads to the formation of highly ordered porous alumina and aniline monomer can be electrochemically polymerized in the formed porous alumina by the anodic reaction. XPS analysis reveals that polyaniline nanowires prepared in this work is protonated emeraldine.     

以DNA为模板构造苯胺-DNA复合物纳米线和聚苯胺纳米导线

在溶液中, 以DNA为模板构造出了线性的苯胺-DNA复合物纳米线. 用压缩气流将得到的复合物纳米线拉直并固定到云母基底上. 用原子力显微镜(AFM)可观察到形貌规整的苯胺-DNA复合物纳米线. 苯胺单体在溶液中能从各个方向上组装到DNA分子上, 从而使DNA模板分子的表面包裹了一层苯胺. 以苯胺-DNA复合物纳米线为前驱体通过进一步化学氧化聚合得到了以DNA为模板的聚苯胺纳米导线.     

Detection of MicroRNAs using target-guided formation of conducting polymer nanowires in nanogaps

A nanogapped microelectrode-based biosensor array is fabricated for ultrasensitive electrical detection of microRNAs (miRNAs). After peptide nucleic acid (PNA) capture probes were immobilized in nanogaps of a pair of interdigitated microelectrodes and hybridization was performed with their complementary target miRNA, the deposition of conducting polymer nanowires, polyaniline (PAn) nanowires, is carried out by an enzymatically catalyzed method, where the electrostatic interaction between anionic phosphate groups in miRNA and cationic aniline molecules is exploited to guide the formation of the PAn nanowires onto the hybridized target miRNA. The conductance of the deposited PAn nanowires correlates directly to the amount of the hybridized miRNA. Under optimized conditions, the target miRNA can be quantified in a range from 10 fM to 20 pM with a detection limit of 5.0 fM. The biosensor array is applied to the direct detection of miRNA in total RNA extracted from cancer cell lines.     

Plasma polymerization of aniline on different surface functionalized substrates

The plasma polymerization of aniline on different surface functionlized low-density polyethylene (LDPE) substrates was investigated, and the resulting polymer was characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and atomic force microscopy. The results showed that the structure of plasma-polymerized polyaniline was rather different from polyaniline synthesized by conventional chemical and electrochemical methods. This difference may be due to extensive coupling reactions and cross-linking reactions during the plasma polymerization process. The use of acrylic acid graft copolymerized LDPE substrate significantly enhanced the adhesion of the polyaniline to the substrate over that observed with pristine LDPE. The plasma polymerized polyaniline can be rendered electrically conductive if the polymerization is carried out on a polystyrenesulfonic acid-coated LDPE substrate. Conductivity can also be induced by acid protonation of the polyaniline by HClO(4). The reaction of the plasma-polymerized polyaniline with viologen grafted on the substrate under UV irradiation and with AuCl(3) and Pd(NO(3))(2) in acid solutions was also investigated.     

聚苯胺/纳米二氧化锰复合材料Ⅰ.原位氧化合成制备

用固相合成法制备了纳米二氧化锰(nm-MnO2),并通过原位聚合法制备了聚苯胺／纳米二氧化锰复合材料。研究结果表明：在苯胺／nm-MnO2的盐酸反应体系中,nm-MnO2可以使苯胺氧化聚合。在一定的nm-MnO2用量下,聚苯胺的产率随苯胺添加量的增加而下降,nm-MnO2在产物中的含量也随之下降,且含量很低。在苯胺：／nm-MnO2／过硫酸铵的反应体系中,研究了Nm-MnO2通过两种不同的加料方式原位制备PA-NI／nm-MnO2复合材料的合成条件。第一种方式为nm-MnO2和过硫酸铵同时与苯胺混合,一起参与苯胺的氧化聚合。第二种方法是先将过硫酸铵和苯胺混合,3min后再将nm-MnO2加入反应体系中。研究表明：第一种加料方式得到的队NI／nm-MnO2中nm-MnO2的含量很低;第二种加料方式可以得到高nm-MnO2含量(w=0．14-0．73)的产物,其电导率约10^-4S／cm。     

ZnO-聚苯胺同轴纳米线及其列阵的制备和表征

以阳极氧化铝膜 (AAO)作模板 ,制备聚苯胺 (PANI)纳米管和PANI纳米管列阵 ;同时利用溶胶_凝胶法制备ZnO_PANI同轴纳米线和同轴纳米线列阵 .PANI纳米管和ZnO_PANI同轴纳米线的形貌通过透射电子显微镜表征 .PANI纳米管的外径约 3 0nm ,内径约 1 0nm ;ZnO_PANI同轴纳米线直径约 60nm .实验发现 ,较之ZnO纳米线 ,同轴AAO模板中纳米线列阵的可见光发射谱带兰移 ,强度显著增强 ,这可能和PANI链上的NH基团与表面Zn2 +离子之间的相互作用有关 ,以及由于ZnO纳米微粒在PANI上富集、PANI的光生载流子部分转移给ZnO微粒所致 .实验还发现分散在NaOH溶液中的同轴纳米线 ,其可见光发射谱带比AAO模板中同轴纳米线的谱带兰移更甚     

On the existence of ordered organic adlayers at the Cu(111)/electrolyte interface

We have reinvestigated the behavior of a Cu(111) electrode in pure and cinchonidine containing aqueous 0.1 M HClO4 solution by cyclic voltammetry (CV) and in situ electrochemical scanning tunneling microscopy (STM). In contrast to previous publications by Wan et al. (Langmuir 2000, 19, 1958-1962 and references cited therein) on Cu(111) in pure 0.1 M HClO4 which claimed an adsorbate-free Cu(111) surface in the entire potential range, we have found a highly ordered hexagonal adsorbate structure with a (4 x 4) unit cell, which is stable in the potential range from hydrogen evolution at -350 to -150 mV (RHE). The adsorbate-free (1 x 1) Cu(111) surface is only visible in a fairly small potential range from -150 to +50 mV. A disordered surface structure is formed at more positive potentials which is interpreted by adsorption of an oxygen-containing species. Furthermore, the formation of a highly ordered cinchonidine adlayer on Cu(111) in 0.1 M HClO4 as reported by Wan et al. (J. Am. Chem. Soc. 2002, 124, 14300-14301) could not be reproduced here. In fact, the similarity of all structures reported by Wan et al. for a great variety of different organic adlayers on Cu(111) in HClO4 solution including cinchonidine with the (4 x 4) superstructure found here already in pure HClO4 solution (i.e., without organic solute) casts serious doubts on the validity of those previous results by Wan et al. in general.     

Conducting poly(aniline) nanotubes and nanofibers: controlled synthesis and application in lithium/poly(aniline) rechargeable batteries

The primary aim of this work was to synthesize aligned perchloric-acid-doped poly(aniline) (HClO(4)-doped PANI) nanotubes by a simple alumina template method and to investigate their application in lithium/poly(aniline) rechargeable batteries. Powder X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Fourier transform infrared (FTIR) analysis were used to characterize the nanostructures obtained. The second aim addressed the preparation of HClO(4)-doped PANI microspheres and nanofibers on a large scale through a modified spraying technique, since the template synthesis has limitations in mass production. The present synthesis methods are simple and can be extended to the preparation of a broad range of one-dimensional conductive polymers. Furthermore, electrochemical measurements showed that the as-prepared HClO(4)-doped PANI nanotubes exhibit better electrode performances than their commercial counterparts because they possess more active sites, higher conductivity, and relative flexibility. This indicates that HClO(4)-doped poly(aniline) nanomaterials are promising in the application of lithium/polymer rechargeable batteries.