Evaluation of ammonia buffer containing EDTA as an extractant for Cr(VI) from solid samples

A novel procedure for the extraction of soluble, sparingly soluble and insoluble Cr(VI) from solid samples was presented. EDTA was added to an ammonia buffer commonly used only for the extraction of soluble and sparingly soluble Cr(VI). In the course of extraction in an ultrasonic bath cations which form insoluble chromates are complexed with EDTA while Cr(VI) is transferred to the solution. A concentration of EDTA equal to 0.01 mol L⁻¹ was chosen. The presence of EDTA in the extraction solution enables not only dissolution of insoluble Cr(VI) but also, as reported previously in literature, minimises oxidation of Cr(III) to Cr(VI). The extraction procedure was optimised and applied to Cr(VI) determination in the paint chips real sample. The results obtained were compared with the results obtained using two other extraction procedures. The results show that the novel extraction procedure can be used for the extraction of soluble, sparingly soluble and insoluble Cr(VI) from real solid samples.     

Improvement on Simultaneous Determination of Cr(III) and Cr(VI) by Capillary Electrophoresis and Chemiluminescence Detection

Chromiumexistsindifferentoxidationstatesingroundwater,industrialwastewater,seawater,andsoilofourenvironment1,2.Chromium(III)isanessentialtraceelementforhumans,requiredforthemaintenanceofnormalglucose,cholesterol,andfattyacidmetabolism.Ontheotherhand,watersolublechromium(VI),intheformCr2O72-orCrO42-,ishighlyirritatingandtoxictohumansandanimals3.Itsacutetoxiceffectsincludeanimmediatecardiovascularshockandlatereffectsonkidney,liver,andblood-formingorgans.Therefore,itisnecessaryforriskassessme…     

Analytical speciation of chromium in in-vitro cultures of chromate-resistant filamentous fungi

In this work, different analytical speciation schemes have been used to study the reduction of Cr(VI) by a chromate-resistant strain of filamentous fungi Ed8 (Aspergillus sp), indigenous to contaminated industrial wastes. As demonstrated previously, this strain has the capability to reduce chromate present in the growth medium without its accumulation in the biomass, yet the reduced chromium end-products have not been characterized. Liquid growth medium, initially containing 50 mg L(-1) Cr(VI), was analyzed for Cr(III)/Cr(VI) and for total Cr at different time intervals (0-24 h) after inoculation with fungi. Three hyphenated procedures, based on the Cr(III)-EDTA formation and species separation by anion-exchange or ion-pairing reversed-phase chromatography with ICP-MS or DAD detection were used. The results obtained for Cr(VI) in each case were consistent, demonstrating efficient reduction of chromate during 24 h of Ed8 growth. However, pre-column complexation with EDTA did not ensure complete recovery of the reduced forms of chromium in the above procedures. An alternative speciation scheme, based on extraction of Cr(VI)-benzyltributylammonium bromide (BTAB) ion pairs into chloroform and subsequent determination of residual chromium by ICP-MS has provided evidence on the effective conversion of chromate into reduced chromium species in the growth medium. The results indicate the feasibility of using Ed8 strain for chromate bioremediation purposes. Analytically it can be concluded that speciation of chromium in biological systems should not be limited to its two most common oxidation states, because the actual reduced chromium species are not converted quantitatively to Cr(III)-EDTA.     

Development of analytical procedures for determination of total chromium by quadrupole ICP–MS and high-resolution ICP–MS,and hexavalent chromium by HPLC–ICP–MS,in different materials used in the automotive industry

A European directive was recently adopted limiting the use of hazardous substances such as Pb, Hg, Cd, and Cr(VI) in vehicle manufacturing. From July 2003 a maximum of 2 g Cr(VI) will be authorised per vehicle in corrosion-preventing coatings of key components. As no standardised procedures are available to check if produced vehicles are in agreement with this directive, the objective of this work was to develop analytical procedures for total chromium and Cr(VI) determination in these materials. The first step of this study was to optimise digestion procedures for total chromium determination in plastic and metallic materials by inductively coupled plasma mass spectrometry (ICP–MS). High resolution (HR) ICP–MS was used to examine the influence of polyatomic interferences on the detection of the ⁵²Cr⁺ and ⁵³Cr⁺ isotopes. If there was strong interference with m/z 52 for plastic materials, it was possible to use quadrupole ICP–MS for m/z 53 if digestions were performed with HNO₃+H₂O₂. This mixture was also necessary for digestion of chromium from metallic materials. Extraction procedures in alkaline medium (NH₄⁺/NH₃ buffer solution at pH 8.9) assisted by sonication were developed for determining Cr(VI) in four different corrosion-preventing coatings by HPLC–ICP–MS. After optimisation and validation with the only solid reference material certified for its Cr(VI) content (BCR 545; welding dusts), the efficiency of this extraction procedure for screw coatings was compared with that described in the EN ISO 3613 standard generally used in routine laboratories. For coatings comprising zinc and aluminium passivated in depth with chromium oxides the extraction procedure developed herein enabled determination of higher Cr(VI) concentrations. This was also observed for the screw covered with a chromium passivant layer on zinc–nickel. For coating comprising a chromium passivant layer on alkaline zinc the standardized extraction procedure was more efficient. In the case of painted metallic plate, because of a reactive matrix towards Cr(VI), its extraction without degradation was difficult to perform.     

Speciation of Cr(VI)/Cr(III) in environmental waters by fluorimetric method using central composite, full and fractional factorial design

In this approach a fluorometric technique has been developed to study chromium speciation, based on optimised conditions using chemometric methods of experimental design and central composite design. Full and fractional factorial design was used for evaluation of the effective factors in determination of Cr(VI) by fluorometric using Rhodamine-6G in the presence of H₂SO₄. Theory and methodology of a central composite design as a chemometric method for the optimisation of analytical procedures were developed in this approach. It was found that the analytical performance for measurement at the point of optimum in this technique is superior and more accurate than that of one variable at a time. Cr(VI) and Cr(III) were measured in a wastewater sample using the proposed technique. The results confirm the selective determination and speciation of Cr(VI)/Cr(III).     

Development of analytical procedures for the determination of hexavalent chromium in corrosion prevention coatings used in the automotive industry

The European directive 2000/53/EC limits the use of Cr(VI) in vehicle manufacturing. Although a maximum of 2 g of Cr(VI) was authorised per vehicle for corrosion prevention coatings of key components, since July 2007 its use has been prohibited except for some particular applications. Therefore, the objective of this work was to develop direct analytical procedures for Cr(VI) determination in the different steel coatings used for screws. Instead of working directly with screws, the optimisation of the procedures was carried out with metallic plates homogeneously coated to improve the data comparability. Extraction of Cr(VI) from the metallic parts was performed by sonication. Two extraction solutions were tested: a direct water extraction solution used in standard protocols and an ammonium/ammonia buffer solution at pH 8.9. The extracts were further analysed for Cr speciation by high-performance liquid chromatography (HPLC) inductively coupled plasma (ICP) atomic emission spectrometry or HPLC ICP mass spectrometry depending on the concentration level. When possible, the coatings were also directly analysed by solid speciation techniques (X-ray photoelectron spectroscopy, XPS, and X-ray absorption near-edge structure, XANES) for validation of the results. Very good results between the different analytical approaches were obtained for the sample of coating made up of a heated paint containing Zn, Al and Cr when using the extracting buffer solution at pH 8.9. After a repeated four-step extraction procedure on the same portion test, taking into account the depth of the surface layer reached, good agreement with XPS and XANES results was obtained. In contrast, for the coatings composed of an alkaline Zn layer where Cr(VI) and Cr(III) are deposited, only the extraction procedure using water allowed the detection of Cr(VI). To elucidate the Cr(VI) reduction during extraction at pH 8.9, the reactivity of Cr(VI) towards different species of Zn generally present in the coatings (metallic Zn and zinc oxide) was studied. The results showed that metallic Zn rapidly reduces Cr(VI), whereas this reaction is less evident in the presence of zinc oxide. Water was then retained for coatings containing metallic Zn.     

Protocol for Extraction and Determination of Cr(VI) in Solid Materials with a High Cr(III)/Cr(VI) Ratio Using EDDS as a Leaching Agent for Cr(VI) and a Masking Agent for Cr(III)

A sensitive and selective protocol for the extraction of all forms of Cr(VI) from solid materials followed by determination by catalytic adsorptive stripping voltammetry has been elaborated. Cr(VI) was leached to a solution with 0.2 mol L^?1 (NH₄)₂SO₄/NH₄OH+0.1 mol L^?1 EDDS (pH 9.5) and simultaneously Cr(III) was transferred to a nonactive electrochemical complex with EDDS. The method allows for Cr(VI) determination in solid samples containing even a 1000–2000 fold excess of extractable Cr(III) without its noticeable influence. The effects of several experimental variables such as the composition and pH of the extractant, the time and temperature of the solid sample mixing with the extractant were studied. At the optimized conditions more than 95% of total Cr(VI) recoveries from solid samples were achieved. The validation of the proposed procedure was carried out by Cr(VI) determination in certified reference material CRM 019 Ash, spiked and unspiked with Cr(III), and by comparing the obtained results with those obtained using other common extraction procedures.     

Recent Developments in Automated Determinations of Trace Level Concentrations of Elements and On‐Line Fractionation Schemes Exploting the Micro‐Sequential Injection—Lab‐On‐Valve Approach

Abstract

The determination of trace level concentrations of elements, such as metal species, in complex matrices by atomic absorption or emission spectrometric methods often requires appropriate pretreatments comprising separation of the analyte from interfering constituents and analyte preconcentration. In this context sequential injection (SI) and lab‐on‐valve (LOV) schemes have proven themselves as superb vehicles to act as front‐end microanalytical methodologies, particularly when employing solid‐phase extraction (SPE) procedures. In this communication, selected SPE‐procedures in the bead‐renewable fashion are presented as based on the exploitation of micro‐sequential injection (µSI‐LOV) using hydrophobic as well as hydrophilic bead materials. The examples given comprise the presentation of a universal approach for SPE‐assays, front‐end speciation of Cr(III) and Cr(VI) in a fully automated and enclosed setup, and the combination of SPE with fractionation schemes of environmentally interesting solid samples (such as soils or sediments) in order to conduct ecotoxicological studies.     

Biosampling for metal speciation

Summary Human erythrocytes (ery's) under physiological conditions are capable of a selective uptake of dissolved chromates beside Cr(III) from aqueous solutions. For sampling the mechanical stability of the red blood cells is increased by immobilization in Ca-alginate beads without loss of the biochemical activity against Cr(VI). Radiotracer studies were performed in order to determine the influence of temperature, pH, and concentration and solubility of chromates on the accumulation, which follows a Michaelis-Menten kinetics. After sampling the ery's are separated from the gel and introduced into a multiple-step clean-up procedure preceding a GFAAS measurement of chromium. The direct determination of chromium in erythrocytes (and comparable matrices) by GFAAS is supported by the use of oxygen as alternate gas during the thermal decomposition of the samples, leading to advantages in routine analysis. The statistical parameters of this method are critically reviewed. The combination of biosampling and GFAAS represents a new way for metal speciation, especially in cases where decomposition of the analyte during standard sampling procedures is likely; this is demonstrated for Cr(III)/Cr(VI) as an example in view of immission measurements of Cr(VI) in airborne particulates.Dedicated to Prof. Dr. G. Tölg on the occasion of his 60th birthday     

Highly sensitive and selective electrochemical detection of sub-ppb level chromium(VI) using nano-sized gold particle

Gold nanoparticle based nanostructured electrode has been developed for the amperometric detection of ultratrace amount of toxic Cr(VI). The nano-sized Au particles have been grown on a conducting substrate modified with sol-gel-derived thiol functionalized silicate network and used for the electroanalysis of Cr(VI). The nanostructured interface show well-defined voltammetric peak for the reduction of Cr(VI) at approximately 0.4 V. The voltammetric behavior of Cr(VI) strongly depends on the coverage of nanoparticle on the electrode surface. Constant potential amperometry has been used for the detection of Cr(VI) at well below the guideline value set by World Health Organization (WHO). This electrode is highly sensitive (30+/-0.2 nA/ppb) and the detection limit (S/N=9) was 0.1 ppb. Cr(III) and coexisting other metal ions and surface active agent present in water do not interfere with the amperometric measurement of Cr(VI). This nanostructured electrode is highly stable and it can be used for continuous measurement of Cr(VI) without using any pretreatment or activation procedures. The accuracy of the measurement has been validated by measuring the concentration of Cr(VI) in the certified reference material (CRM).     

塑料中痕量Cr(VI)的RoHS符合性测定及影响因素分析

六价铬Cr(VI)的不稳定性使其成为RoHS(限定有害物质, Restriction of Hazardous Substances)符合性测试的难点之一. 采用分光光度法对塑料中痕量Cr(VI)进行检测, 着重研究Cr(VI)萃取与显色中的过程参数与干扰因素的影响, 并建立了一套试样制备、萃取、显色等标准程序. 研究表明, 采用混合碱萃取法可对Cr(VI)进行有效提取, 同时消除Cr(III)的干扰, 通过排除共存离子影响, 优化萃取、显色、标定过程中pH值、温度和时间等参数, 可使试样和加标溶液的回复率保持在90%～110%之间, RSD＜1%, 校准在低浓度范围(0～500 μg/L)呈良好线性关系. 提出的方法和检测程序具有较高的精确度和灵敏度, 而且操作简单、快速, 为信息产业应对RoHS符合性测试提供了较好的技术支持.     

Flame Atomic Absorption Spectrometric Determination of Total Chromium and Cr(VI) in Cigarette Ash and Smoke using Flow Injection/Hydraulic High-Pressure Sample Introduction

Total chromium and Cr(VI) contents of cigarettes, ash, and smoke formed while burning cigarettes were determined. The determinations of chromium species were carried out according to procedures developed earlier. Cr(VI) was determined in a combined system, which involves a flow injection (FI) sorption preconcentration system, hydraulic high-pressure nebulization (HHPN) sample introduction technique, and flame atomic absorption spectrometric (FAAS) detection. The total chromium of samples in Cr(VI) form was determined in this same combined system after ashing cigarettes at 800°C [after total conversion of Cr(III) of the sample to Cr(VI)]. It was found that while burning cigarettes 0.8–1.2% of the original chromium content of the cigarettes comes to smoke in the toxic Cr(VI) form.     

Chromium speciation in solid matrices and regulation: a review

In recent years, the extensive use of chromium in industrial processes has led to the promotion of several directives and recommendations by the European Union, that try to limit and regulate the presence of Cr(VI) in the environment and to protect industrial workers using chromium and end-users of manufactured products. As a consequence, new standard methods and analytical procedures have been published at the EU level for Cr(VI) determination in soil, sludge, sediment, and similar waste materials, workplace atmospheres, cement, packaging materials, industrially produced samples, and corrosion-protection layers on some components of vehicles and electrical and electronic equipment. The objective of this article is to summarize the different directives and recommendations and to critically review the currently existing standard methods and the methods published in the literature for chromium speciation in the above mentioned solid matrices, putting the emphasis on the different extraction procedures which have been developed for each matrix. Particular attention has been paid to Cr(III) and Cr(VI) inter-conversions that can occur during extraction and efforts to minimize these unwanted reactions. Although the use of NaOH-Na₂CO₃ solutions with hot plate extraction seems to be the more widespread procedure, species transformation can still occur and several studies suggest that speciated isotope-dilution mass spectrometry (SIDMS) could be a suitable tool for correction of these interconversions. Besides, recent studies have proved the role of Cr(III) in chromium toxicology. As a consequence, the authors suggest an update of standard methods in the near future.     

Digestion treatments and risks of Cr(III)–Cr(VI) interconversions during Cr(VI) determination in soils and sediments—a review

Threshold values for Cr(VI) in various types of solid matrices have been set up to protect human health and biota. To ascertain the compliance of solids with these limits different types of extractants and different conditions of pH and temperature have been proposed in the literature. These extraction procedures are reviewed and their potentialities in quantitatively extracting Cr(VI) from solids without inducing undesired Cr(VI)–Cr(III) interconversions during the extraction are carefully evaluated. This evaluation takes into account the knowledge of the kinetics of most important redox reactions of chromium gathered in recent years. Among possible Cr(VI) reductants made available during the digestion, a number of species including Fe(II), sulphide, sulfite and humic matter were considered, while oxidants included hydrogen peroxide, dissolved oxygen, manganese oxides. Theoretical calculations suggest that pH higher than 10, high temperature and high concentrations of carbonate and magnesium ions minimize Cr(III)–Cr(VI) interconversions. The EPA Method 3060A meets these basic requirements. However, the applicability of this method to the analysis of Cr(VI) in soil and sediment samples, whose extracts may suffer from the interference by humic matter, is questionable.     

Different Lubricating Oil Treatments for the Determination of Cu,Cr, Fe,Ni, Sb,Pb, and Zn by HR-CS FAAS

Abstract

Microwave-assisted acid decomposition, direct dilution in kerosene, and oil-in-water emulsion were evaluated as lubricating oil pretreatment procedures for Cu, Cr, Fe, Ni, Pb, Sb, and Zn determination by High-Resolution Continuum Source Flame Atomic Absorption Spectrometry (HR-CS FAAS). For wet digestion, results were compared with those obtained by Flame Atomic Absorption Spectrometry (FAAS). The ultrasound probe used in emulsions sonication contaminated samples with Cr, although better results have been observed for the other six elements in this condition. In general, recovery percentages ranging from 81–106% (Cu), 80–107% (Cr), 85–114% (Fe), 82–116% (Ni), 86–117% (Pb), 85–115% (Sb), and 81–114% (Zn) were obtained. The HR-CS FAAS showed to be faster and more sensitive than FAAS.     

Comparison of single extraction procedures,using either conventional shaking or microwave heating,and the Tessier sequential extraction method for the fractionation of heavy metals from environmental samples

The conventional four-step sequential extraction method and the EDTA and acetic acid single extraction procedures were applied to sewage sludge and sediment samples. The results obtained with these samples for Cu, Cr, Ni, Pb and Zn using the Tessier method were compared with those supplied by the two single extraction procedures employed. In addition, the Tessier method was also applied to a reference material, CRM 483, and these results were also compared with the certified EDTA and acetic acid values for this sample. As a result, good agreement was found between the metal contents released in the first three fractions of the Tessier method and those leached by the simpler single extraction procedures for the most of the elements studied. Subsequently, the conventional EDTA and acetic acid extraction methods were accelerated by means of microwave energy, in order to reduce the operating time. The extraction efficiency of the first three fractions of the Tessier method was compared with that obtained using the optimised microwave single extraction procedures and only in sewage sludge and CRM 483 samples were satisfactory results found for all the elements studied, except Cr and Pb. This means that the microwave single extraction procedures optimised in this work could be employed as screening methods to evaluate rapidly the easiest mobilizable heavy metals in these samples, although more samples should be analysed to determine their general applicability. The application of the accelerated single extraction procedures to a reference material, CRM 483, provided satisfactory results for all the elements studied, except for Cr in both methods and for Pb in the acetic acid extracts.     

Rapid Procedure to Determine Wear Metals in Lubricating Oils and the Analysis of Variance in the Evaluation of Sample Preparation Procedures

 A new sample treatment is proposed based on a partial wet digestion in closed reactors assisted by microwaves for wear metal determinations by flame atomic absorption spectrometry (FAAS). It is rapid, precise and sensitive and allows the use of inorganic standards. Problems concerning solubility have been overcome with mixed solvents. The repeatability, stability, calibration curve and limit of detection were established. Six samples, with different degree of wear were analyzed for Fe, Cu, Pb and Cr by FAAS using the procedure proposed and other sample treatment procedures from the literature. Pb and Cr were not found in all samples. The one-way analysis of variance for Fe applied to each sample confirms the need of an acid attack and the importance of HCl for the digestion. The results obtained for Cu led us to use a two-way analysis of variance for all the samples considering the preparation procedures and the samples as variation sources. It showed no significant differences for the preparation procedures used. Therefore, treatments implying the use of acids are recommended when several wear metals are analyzed. On the other hand, the differences between the simple dilution and the procedures, implying the dissolution of metallic particles is an index to predict an imminent engine failure. Received March 1, 2001. Revision July 10, 2001.     

A new flow cell design for chemiluminiscence analysis

The present study proposes a new flow cell called a bundle cell for chemiluminescence analysis. The results obtained were compared with those achieved by manual and automated batch procedures and flow manifolds with different cells: an common quartz flow cell, a helix cell and the most used spiral cell. Figures of merit such as limit of detection, sensitivity, accuracy and precision for the Cr(III) determination were established with light emission produced by catalysed Cr(III) luminol oxidation by hydrogen peroxide in a basic aqueous solution. An improvement in sensitivity about 50% as compared with the spiral cell and even larger with respect to the other flow cells tested was observed. The limit of detection provided was lower than those obtained with the other flow cells. In reference to the batch mode, similar results were obtained with the bundle flow cell. Good results were obtained for several real water samples containing chromium at different concentrations.     

Comparison of aqua regia and HNO3-H2O2 procedures for extraction of Tl and some other elements from soils

The relationship between aqua regia (ISO 11466) and HNO(3)-H(2)O(2) (ISO/CD 20279) extraction procedures for atomic emission spectrometric (ICP/OES and ICP/MS) determinations of Tl, P, Mn, Fe, Mg, Ca, Sr, Al, K, As, Bi, Zn, Pb, Co, Cd, Ni, V, Be, Cu and Cr was investigated. Soil samples (155) representing areas with different contents of the elements were selected for the comparison. Tl was the element of the highest interest and therefore the sampling sites were chosen to achieve as wide range of Tl contents as possible. Both extraction procedures are comparable in results (differences lower than 10% for the most of the elements) for all the tested elements. Statistically non-significant differences between the two extraction procedures were found for P, Zn, V and K (the slope was very close to 1 and the intercept included zero). Statistically significant values of intercepts were found for Fe, Al, Ca, Cd, Sr and Ni. Significantly higher results for aqua regia were found for Cu (12%), Pb (17%), Mn (11%) and lower results by aqua regia were found for Mg (4%), As (13%), Co (20%), Be (11%), Cr (4%) and Bi (6%). The results for Tl, the element of the highest interest, after HNO(3)-H(2)O(2) extraction procedure, were approximately 6% higher than the results after aqua regia extraction. Content of Tl in the soil samples was from 0.08 to 2.8 mg kg(-1). A highly significant linear relationship was found (R(2)=0.97).     

Determination of As,Cd, Cr,Cu, Hg,Sb and Se concentrations by radiochemical neutron activation analysis in different Brazilian regional diets

The present paper describes radiochemical separation procedures developed for the determination of seven elements: As, Cd, Cr, Cu, Hg, Sb and Se in different Brazilian regional diets. In the case of the elements As, Hg, Sb and Se, the procedure was based on retention in inorganic exchanger TDO (tin dioxide) and determination of Hg by extraction with Ni(DDC)₂. For determination of Cd, Cr, Cu and Se the procedure chosen was based on retention in inorganic exchanger HMD (hydrated managese dioxide) and extraction of Cu and Cd as diethyldithiocarbamate compounds. The accuracy and precision of the methods studied were tested by means of analyses of different reference materials. Due to the lack of data on trace element levels in Brazilian foodstuffs and diets, these methods were applied to determination of these elements in different Brazilian regional diets. These diets were supplied by the Food and Experimental Nutrition Department of the Faculty of Pharmaceutical Science, University of São Paulo. The daily dietary intake values for these diets are presented for As, Cd, Cr, Cu, Hg, Sb and Se.