不同色浆质量分数的水性聚氨酯涂料对聚氯乙烯表皮低温爆破性能的影响

本文制备了一系列不同色浆质量分数的水性聚氨酯涂料,并将其喷涂在汽车仪表板聚氯乙烯(PVC)表皮的背面形成复合材料。 用旋转流变仪表征了涂料的粘度以评价其喷涂性能;用差示扫描量热仪表征了材料的玻璃化转变温度(T_g);利用万能材料试验机表征了材料在-30 ℃条件下的拉伸性能及抗撕裂性能;用动态热机械分析仪表征了材料的损耗比随温度的变化。 结果表明:不同色浆质量分数的涂料都能喷涂,含有涂层材料PVC表皮在-30 ℃低温爆破性能与涂层材料的T_g、低温拉伸性能、抗撕裂性能的关系并不大,而与涂层材料的阻尼性能直接相关。 材料的阻尼性能越好,其低温爆破性能越好。     

双极绿色磷光主体材料1-甲基-3-[4-(9-咔唑基)苯基]-4-苯基喹啉-2(1H)-酮的合成与性能研究

设计并合成了一种基于喹诺酮衍生物的双极绿色磷光主体材料1-甲基-3-[4-(9-咔唑基)苯基]-4-苯基喹啉-2(1 H)-酮.计算发现,化合物的HOMO轨道的电子云位于咔唑基团,LUMO轨道的电子云位于喹诺酮基团,是一种良好的双极材料.化合物的磷光发射峰为515 nm(2.41 eV),符合绿色磷光主体材料的基本要求(>2.4 eV).热失重和差热分析结果表明,该化合物具有较高的热稳定性,分解温度和玻璃化转变温度分别为312℃和105℃.研究结果表明:该新型化合物是一种潜在的具有双极特性的绿色磷光主体材料.     

柔性OLED用高耐热聚酰亚胺薄膜的制备与性能

聚酰亚胺(PI)薄膜作为柔性有机发光显示(OLED)基板材料应用时, 需要满足玻璃化转变温度(T_g)大于450 ℃和热膨胀系数(CTE)在0~5×10^-6 K^-1之间. 为了提高PI薄膜的热性能, 本文合成了2,7-占吨酮二胺 (2,7-DAX), 并将其与均苯四甲酸二酐(PMDA)和2-(4-氨基苯基)-5-氨基苯并噁唑(BOA)共聚制备了一系列新型PI薄膜. 研究了PI薄膜的聚集态结构、 耐热性能、 尺寸稳定性和力学性能. 结果表明, 占吨酮结构和苯并噁唑结构提高了PI分子链的刚性与线性, 使分子链在平面内紧密堆积与取向, 制备的PI薄膜综合性能优异, 玻璃化转变温度高于408 ℃, CTE在-5.0×10^-6~8.1×10^-6 K^-1之间, 拉伸强度大于140 MPa, 拉伸模量大于4.2 GPa, 断裂伸长率为7.1%~20%, 5%热失重分解温度(T_5%)在601~624 ℃之间. 其中, PI-50和PI-60薄膜具有超高玻璃化转变温度和超低热膨胀系数, T_g高于450 ℃, CTE分别为2.1×10^-6 K^-1和1.6×10^-6 K^-1. 制备的系列PI薄膜作为柔性OLED基板材料有潜在应用前景.     

磷光客体三重态能级对基于PVK主体的电致发光器件的影响

将磷光客体掺入PVK:PBD主体材料中是获得高效率磷光电致发光器件 (PhPLED)的有效途径.然而,分别掺杂Ir(pppy)₃、Ir(F-pppy)₃和Ir(F₂-pppy)₃三种磷光客体的PhPLED器件性能件却显著不同.我们分别模拟主-客体间能量转移和客体直接捕获电子空穴对两种机制,研究了三种客体材料的磷光发射及其衰减过程.研究表明:平衡的载流子注入和客体高效率的载流子捕获是实现Ir-配合物掺杂的PhPLED器件性能优良的主要机制,PVK较低的三重态能级使其无法成为蓝光磷光电致发光器件的主体,在PVK中掺入PBD的方法,则进一步降低了主体材料的三重态能级,这是蓝光磷光电致发光器件运行效率较低的主要原因.本文的研究结果可为高分子磷光电致发光器件的制备技术和新型磷光主体的设计提供参考.     

耐高温可溶性聚酰亚胺树脂及其复合材料

制备了2种耐高温可溶型聚酰亚胺树脂(PI-1, PI-2)及其复合材料, 系统研究了树脂的工艺性, 纯树脂固化物的热性能及其复合材料的界面形貌、 介电性能和力学性能. 研究结果表明, 树脂低聚物在极性非质子溶剂中具有良好的溶解性, 且熔体黏度较低, 表明其具有优异的加工性能. 两种树脂固化物在空气中的5%热失重温度均高于550 ℃, PI-1树脂的玻璃化转变温度(T_g)为430 ℃, PI-2树脂的T_g为380 ℃. 石英纤维/PI-1和石英纤维/PI-2复合材料具有较低的介电常数和介电损耗. 碳纤维/PI-1复合材料在420 ℃下的弯曲强度保持率可达62%, 层间剪切强度保持率可达48%, 具有较优异的高温力学性能. 采用普通模压工艺制备了厚度高达45 mm的复合材料制件, 进一步证明这2种树脂具有优异的工艺性.     

基于三苯胺/二苯砜的热激活延迟荧光材料

通过Suzuki反应合成了三种基于三苯胺/二苯砜的热激活延迟荧光(TADF)材料(1-3),采用紫外-可见(UV-Vis)吸收光谱、时间分辨荧光发射光谱、循环伏安(CV)测试、理论计算、热重分析和差示扫描量热法,系统地研究了三种材料的光物理、电化学、延迟荧光性能和热稳定性.材料1-3均为基于分子内电荷转移(ICT)的双极性分子.三种材料在薄膜中的单线态-三线态能级差分别为0.46、0.39和0.29 eV.荧光量子效率和荧光寿命的测试结果表明,三种材料均能发射延迟荧光,其中材料3具有最佳的延迟荧光性能.材料1-3的最高占有分子轨道(HOMO)能级分别为-4.91、-4.89和-4.89 eV.结合UV-Vis吸收光谱中得到的能隙(E_g)值,我们得到材料1-3的最低未占分子轨道(LUMO)能级,分别为-1.74、-1.89和-1.94 eV.热分析的结果表明,材料1-3具有其较高的热分解温度(T_d,失重5%时的温度),分别为436、387和310 ℃.     

发蓝光聚醚醚酮材料的合成及其光电特性

通过4-羟基苯甲醛与2,6-二(4-氯甲基苯基)苯并[1-2,4-5′]二唑之间的Wittig反应,制备了具有蓝色荧光特性的小分子单体2,6-二{4-[2-(4-羟基苯基)乙烯基]苯基}苯并[1-2,4-5′]二唑,在碳酸钾的催化作用下,通过其与4,4′-二氟二苯甲酮的缩聚反应,设计并合成了以均二苯乙烯为共轭母核的可发射蓝光的聚醚醚酮材料(BOE-PEEK),并对其结构进行了表征.测定结果表明,该聚合物的平均分子量(-Mw)为1.38×10⁵,均分散系数(PDI)为4.35,玻璃化温度(T_g)为195℃,热分解温度(T_d)为440℃,BOE-PEEK在二甲基乙酰胺(DMA)溶剂中的UV-Vis吸收光谱(λ_max)为372 nm,荧光光谱(λ_max)为455nm,由导电玻璃/发光层/金属铝电极(ITO/BOE-PEEK/Al)组成的单层器件在电压15 V时,发光亮度达530 cd·cm^-2,发光效率为0.36 cd/A.     

一种联咔唑类双极性蓝色磷光主体材料的合成及性能

以联咔唑作为电子给体,二苯基磷氧基团作为电子受体,设计合成了双极性蓝色磷光主体材料6,6'-二(二苯基磷氧基)-9,9'-二己基-3,3'-联咔唑(DPDBC)。通过紫外-可见(UV-Vis)、荧光、低温磷光、循环伏安法、热重分析(TGA)、差热分析(DSC)和密度泛函理论(DFT)对其性能及轨道能级等进行了研究。结果表明,化合物DPDBC在CH₂Cl₂稀溶液中有两个吸收峰,最大吸收峰位于306 nm;它的荧光发射峰位于420 nm,属于深蓝色荧光;DPDBC的低温磷光光谱的第一发射峰位于447 nm,其三重态能级为2.77 eV,与蓝色磷光客体材料FIrpic (2.62 eV)的能级相匹配;测定其循环伏安特性曲线,计算得到它的HOMO能级为-5.48 eV,与阳极ITO的功函(-4.5~-5.0 eV)相匹配,LUMO能级为-2.36 eV,接近于电子传输材料PBD(-2.82 eV),表明它具有双极性能;TGA显示其分解温度为410℃,表明热稳定性能优良,DSC显示其T_g温度为140℃,表明其具有无定形态结构及良好的成膜性能。因此,DPDBC是一种集双极性传输性能于一体,同时又具有优良热稳定性能的潜在蓝色磷光主体材料。     

基于9,9'-螺二芴和萘的纯碳氢主体材料（英文）

利用磷光有机发光二极管的主客体掺杂结构有助于避免三重态激子浓度猝灭,从而提高器件性能.9,9’-螺二芴(SBF)及其衍生物具有独特的正交构型和刚性骨架,具有高玻璃化转变温度、高三线态能级和用作主体材料的潜力.通过引入萘环合成并表征了两种基于SBF的纯碳氢化合物(PHC)磷光发光器件的主体材料,命名为1,4-SBF-Nap和1,8-Oct-Nap.其中,1,8-Oct-Nap分子存在一个有趣的环化反应,形成八原子环结构而不是一般的SBF.以Ir(MDQ)₂(acac)为客体,成功制备了基于这两种主体的红光器件,最大外量子效率(EQE)分别为15.0%和13.7%,证明PHC主体材料在设计上的多样性.     

快速扫描量热法研究聚对苯二甲酸-1,4-环己烷二甲醇酯的结晶和熔融行为

采用快速扫描量热法(FSC)结合传统的差示扫描量热仪(DSC)考察了聚对苯二甲酸-1,4-环己烷二甲醇酯(PCT)聚酯在接近玻璃化转变(T_g)和熔融温度(T_m)范围(100~270 ℃)的结晶和熔融行为。 较大过冷度时PCT聚酯结晶较快,FSC有效地抑制降温过程结晶的发生,而较低过冷度下传统DSC可以避免样品降解对实验结果的影响,二者的结合能很好地对PCT聚酯结晶动力学进行测量,实验结果表明在175 ℃时结晶速率最快。 并且利用Flash DSC对等温结晶温度下形成的片晶熔点进行加热速率的相关测量,在熔融动力学建模的基础上进行校准,以确定零加热速率下片晶的熔点。 Hoffman-Weeks方程中T_m与结晶温度(T_c)的线性关系与T_c=T_m的交点给出了PCT晶体的平衡熔融温度$T_m^o$为315 ℃。     

Nonconjugated hybrid of carbazole and fluorene: a novel host material for highly efficient green and red phosphorescent OLEDs

[structure: see text] A novel host material for efficient green and red electrophosphorescence devices is obtained by adopting the new molecular strategy of nonconjugated linkage of carbazole and fluorene moieties. The new host combines characteristics of both carbazole and fluorene, giving a large-gap host material suitable for green and red phosphorescent OLEDs. Green and red phosphoresecent OLEDs with external quantum efficiencies up to 10% have been achieved with this new host material.     

Stable and good color purity white light‐emitting devices based on random fluorene/spirofluorene copolymers doped with iridium complex

Conjugated polymers PSNFP and PSNFF based on naphthalene‐containing spirofluorene structure and 9,9‐dioctylfluorene, 2,5‐dioctylbezene were designed and synthesized for light emitting applications. These two polymers show good blue emission both in solution and thin film. Thermal gravimetric analysis reveals they have good thermal stability with the decomposition temperature higher than 400 °C. Electrochemistry characterization shows that both of these polymers have a large band gap and deep highest occupied molecular orbital, which are important features for phosphorescent host materials. White light‐emitting diodes were fabricated by using PSNFF as the host material, containing two typical phosphorescent Ir complex dopants: green emitter Ir(mppy)₃ and red emitter Ir(piq)₂. The color coordinate CIE stayed nearly constant, changed from (0.32, 0.31) to (0.28, 0.31) when the current density varied from 2 to 20 mA cm^?2. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

An electron-transporting host material compatible with diverse triplet emitters used for highly efficient red- and green-electrophosphorescent devices

A bifluorene analogue, T2N, containing a pyridyl moiety serves as both a host and an efficient electron-transporting material that is compatible with various heavy metal-containing red (Ir, Ru, Os, and Pt) and green (Ir) phosphors for highly efficient phosphorescent OLEDs possessing simple device architectures.     

A Bipolar and Small Singlet‐Triplet Splitting Energy Host with Triplet Energy Lower Than a Blue Phosphor for Phosphorescent OLEDs in Panchromatic Range

A bipolar host material, 2,4,6‐tris(3‐(carbazol‐9‐yl)phenyl)‐triazine (TCPZ), was synthesized according to reported method. Due to the higher triplet energy compared to green and red phosphors, TCPZ is suitable to host them in phosphorescent organic light‐emitting diodes (PhOLEDs). Although the triplet of TCPZ is slightly lower than a common blue phosphor, good blue PhOLEDs using TCPZ as the host were successfully demonstrated in this work. By low temperature emission measurement, it was found that the energy splitting between the singlet and triplet of TCPZ is as small as 0.24 eV. Therefore, thermal activated energy transfer from triplet to singlet in the host TCPZ is expected to occur, which can be afterwards efficiently transferred to the blue phosphor, hence enabling it to host blue phosphor. As a result, TCPZ can be used as host for phosphors in panchromatic range. Additionally, single‐carrier devices clearly prove its good bipolar transport feature, beneficial to device performance. By using TCPZ as a host, high performance deep‐red, green and blue PhOLEDs have been achieved, with maximum efficiencies of 9.3 cd·A^?1 (13.2%), 81.3 cd·A^?1 (23.1%) and 17.03 cd·A^?1 (10.4%), respectively.     

Energy transfer and triplet exciton confinement in polymeric electrophosphorescent devices

Energy transfer and triplet exciton confinement in polymer/phosphorescent dopant systems have been investigated. Various combinations of host‐guest systems have been studied, consisting of two host polymers, poly(vinylcarbazole) (PVK) and poly[9,9‐bis(octyl)‐fluorene‐2,7‐diyl] (PF), blended with five different phosphorescent iridium complexes with different triplet energy levels. These combinations of hosts and dopants provide an ideal situation for studying the movement of triplet excitons between the host polymers and dopants. The excitons either can be confined at the dopant sites or can flow to the host polymers, subject to the relative position of the triplet energy levels of the material. For PF, because of its low triplet energy level, the exciton can flow back from the dopants to PF when the dopant has a higher triplet energy and subsequently quench the device efficiency. In contrast, efficient electrophosphorescence has been observed in doped PVK films because of the high triplet energy level of PVK. Better energy transfer from PVK to the dopants, as well as triplet exciton confinement on the dopants, leads to higher device performance than found in PF devices. Efficiencies as high as 16, 8.0, and 2.6 cd/A for green, yellow, and red emissions, respectively, can be achieved when PVK is selected as the host polymer. The results in this study show that the energy transfer and triplet exciton confinement have a pronounced influence on the device performance. In addition, this study also provides material design and selection rules for the efficient phosphorescent polymer light‐emitting diodes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2681–2690, 2003     

基于咔唑-三唑的新型主体材料及天蓝光有机电致磷光器件

本研究针对蓝光主体材料相对缺乏的现状,利用有机电致磷光器件高效率的优势,选择1,2,4-三唑为电子传输功能基团、咔唑为空穴传输功能基团,设计、制备了新型主体材料oCzTz。通过邻位取代方式实现了分子立体构型高度扭曲,从而使分子的三重态能量达到3.01eV;oCzTz具有较高的热分解温度(353℃)和玻璃化转变温度(110℃);量化计算显示,分子的前线轨道在咔唑和三唑基团之间高度分离。以oCzTz为主体、以FIrpic为发光客体的天蓝光电致磷光器件启亮电压为3.4V,电流效率和功率效率分别高达37.2cd·A-1和29.2lm·W-1,是以TPBI为电子传输层的同类器件的最高效率之一。     

Efficient and Low-voltage Phosphorescent Organic Light-emitting Devices Based on Blue Iridium Complex Host

By adopting a phosphorescent host/guest system consisting of blue iridium complex as host and a series of phosphorescent dyes as guest, efficient and low-voltage monochromic organic light-emitting devices(OLEDs) were fabricated. The devices with blue iridium host have higher power efficiency than the device with the conventional host 4,4'-N,N'-dicarbazole-biphenyl. The enhancement of the maximum power efficiency in green phosphorescent device can reach 37.2%. Dichromatic white OLED could be achieved by simply adjusting the concentration of the orange dyes. At a brightness of 1000 cd/m², the power efficiency of the white device is 8.4 lm/W with a color rendering index of 76.     

High triplet energy polymer as host for electrophosphorescence with high efficiency

We report the conjugated polymer P(tBu-CBP) as a host with high triplet energy (E(T) 2.53 eV) and suitable HOMO (5.3 eV) and LUMO (2.04 eV) energy levels. Upon doping with green and red emission Ir-complexes, it gives devices with high luminous and external quantum efficiencies for green emission (23.7 cd/A, 6.57%) and for red emission (5.1 cd/A, 4.23%), respectively, and low turn-on voltage (3 V). For both devices, the efficiencies are higher than those of the corresponding devices with the same backbone P(3,6-Cz) as a host by a factor of 4, even though the latter has an E(T) (2.6 eV) slightly higher than that of the former. The results reflect that, in phosphorescent devices, the difference in E(T) between the host and guest is not the only factor that determines the device efficiency, and the present side group modification via the 9 position of carbazole also plays an important role, which allows a tuning of HOMO and LUMO levels to provide more balance in electron and hole fluxes and provides prevention from formation of excimer.     

Selective Introduction of Carbazole and Diphenylamine into Spirofluorenexanthene Core for Different Phosphorescent Hosts

Built on the spiro[fluorene‐9,9′‐xanthene] (SFX) core and two frequently‐used hole‐transporting groups such as carbazole and diphenylamine, two SFX derivatives, namely SFXCz and SFXDPA, have been synthesized by one‐step reaction for red, green and blue phosphorescent organic light‐emitting devices (PHOLEDs). Though the properties of these two groups are very similar, the devices based on SFXCz and SFXDPA exhibit distinct performances. In blue PHOLEDs, the device based on SFXCz exhibited much better performances than that based on SFXDPA. However, the latter was superior to the former in green and red PHOLEDs. And the red PHOLED based on SFXDPA exhibited maximum current efficiency (CE) of 27.1 cd·A^?1, power efficiency (PE) of 25.0 lm·W^?1, and external quantum efficiency (EQE) of 15.0%. The results show that the introduction of diphenylamine group is suitable for constructing green and red host materials, whereas the introduction of carbazole group is suitable for constructing blue host materials.