导电聚吡咯纳米线的电化学无模板法可控合成与表征

以β-萘磺酸(NSA)为掺杂剂,采用电化学无模板法制备了聚吡咯(PPy)纳米线.研究了NSA浓度、吡咯(Py)单体浓度及反应温度对PPy纳米线形貌的影响.分别采用场发射扫描电子显微镜(FE-SEM)和拉曼光谱对PPy纳米线的结构形貌和化学结构进行了表征.结果表明,利用电化学无模板法可得到中空的PPy纳米线;NSA浓度会影响PPy纳米线的取向性;增大Py单体浓度,可制得圆锥状PPy纳米线;低温有利于合成形状细长、紧密堆积的PPy纳米线.PPy纳米线形貌受游离Py浓度及Py-NSA胶束数量影响,通过调节NSA浓度、Py浓度及反应温度改变游离Py浓度及Py-NSA胶束数量,可制得不同形貌的PPy纳米线.     

聚吡咯纳米阵列电极的光电化学

以多孔的铝阳极氧化膜(AAO)为模板制备了直径约为80 nm聚吡咯(PPy)纳米线的阵列电极, 并研究了它的光电化学响应. 结果表明, 在电极电位低于－0.1 V(vs Ag/AgCl)时出现的阴极光电流是由聚吡咯纳米线的p型半导体性质引起的, 其平带电位为－0.217 V. 聚吡咯纳米线的长度对光电流的影响较大, 最佳长度为42 nm. 这是因为在很短的聚吡咯纳米线阵列中PPy太少, 产生的光电流弱, 而在过长的聚吡咯纳米线阵列中光生电子在到达电极基底前易于与光生空穴复合而消失. 聚吡咯纳米线有可能作为纳米光电器件用于未来微器件系统.     

肝素钠掺杂球状聚吡咯的合成及其电化学电容

以生物制剂肝素钠为掺杂剂,由自组装方法合成出平均粒径为100 nm的球状聚吡咯(PPy),用作超级电容器电极材料.透射电镜(TEM)、循环伏安、恒流充放电和电化学交流阻抗测试表明,肝素钠掺杂聚吡咯呈现较好的形貌和电容性质,在电流密度3 mA/cm2下充放电,单电极比电容达到338 F/g.     

二维多层状Ti3C2Tx-MXene/聚吡咯纳米线复合材料的制备及电容性能研究

本文以体相材料MAX(Ti₃AlC₂)为基底,采用氢氟酸刻蚀法得到二维多层状Ti₃C₂T_x-MXene,将一维聚吡咯纳米线(polypyrrole nanowires,PPy-NW)与二维多层状Ti₃C₂T_x-MXene相结合,成功地制备出Ti₃C₂T_x-MXene/PPy-NW复合电极材料. 并分别利用扫描电子显微镜(scanning electron microscope,SEM)、X-射线衍射(X-ray diffraction,XRD)、傅里叶变换红外光谱(fourier transform infrared spectroscopy,FTIR)及X射线光电子能谱 (X-ray photoelectron spectroscopy,XPS)对其进行了形貌和结构表征. 最后通过电化学测试表明,二维多层状Ti₃C₂T_x-MXene/PPy-NW复合电极材料在扫描速率为10 mV·s^-1时比电容可达374 F·g^-1,高于纯PPy-NW（304 F·g^-1）,当扫描速率增加至200 mV·s^-1时,仍可保留原比电容值的72.4%,展现出良好的倍率性能. 而且在电流密度为5 A·g^-1下经过2000次的循环伏安实验,其电容保持率可达91.6%,具有良好的循环稳定性. 总之,二维多层状Ti₃C₂T_x-MXene和一维PPy-NW的复合有效地提升了电极材料的电容性能,在电化学能源储存方面有着巨大的应用前景.     

聚吡咯纳米线凝胶的模板制备及储能与电化学传感性能

以配位聚合物凝胶为模板, 构筑均一的聚吡咯纳米线网络, 聚合后经简单处理除去模板, 得到性能优异的聚吡咯凝胶. 结果表明, 模板法合成的聚吡咯凝胶为由均一纳米线组成的三维网络结构, 具有良好的力学性能、 较大的比表面积及优异的电化学特性, 在0.28 A/g电流密度下, 比电容可达450 F/g, 在2.8 A/g电流密度下充放电1000次, 比电容仍可保持88.6%. 聚吡咯纳米线网络凝胶经葡萄糖氧化酶负载后得到柔性传感电极, 对低浓度(0.2 mmol/L)的葡萄糖具有快速响应性能, 有望用于超级电容器及生物电化学传感器等领域.     

电化学沉积制备氧化石墨烯/聚吡咯复合材料及其用于超级电容器的研究

本文采用改进的Hummers法制备氧化石墨烯(GO),利用电化学沉积法制备聚吡咯(PPy)和GO/PPy复合材料并对其作为超级电容器电极材料进行了探究。通过XRD、FT-IR、AFM和SEM对其结构和形貌进行了表征,研究表明:PPy成功在GO片层上生长,并改变了原来PPy类逗号形的形貌,形成了无定形结构的GO/PPy复合材料。循环伏安法(CV)对不同电沉积时间的PPy和GO/PPy电容量进行了测试,发现电沉积时间为17min的PPy和GO/PPy均表现出较优的电容性能。在1A/g电流密度下进行恒流充放电(CP)测试,通过比较发现GO/PPy比PPy的比电容量提高了82. 3%,达到332. 37F/g。     

氢键诱导的聚吡咯/苯磺酸功能化多壁碳纳米管的制备及其电化学行为

采用原位芳基重氮化反应对碳纳米管进行苯磺酸功能化, 进而制备了聚吡咯/苯磺酸化碳纳米管复合材料(PPy/f-MWCNTs), 通过透射电镜(TEM)及扫描电镜(SEM)测试发现, 氢键诱导使聚吡咯成功地包覆在碳纳米管表面. 循环伏安和恒流充放电测试结果表明, 复合材料具有良好的电化学电容性能, 当聚吡咯与苯磺酸化碳纳米管质量比为1:1时, 复合材料在1.0 A·g-1的电流密度下的比容量达266 F·g-1, 而且聚吡咯利用率比未功能化聚吡咯/碳纳米管(PPy/p-MWCNTs)和纯聚吡咯(PPy)提高了1倍以上.     

聚吡咯/还原氧化石墨烯复合物的合成及电容性能

通过原位聚合方法制备不同配比的聚吡咯/氧化石墨（PPy/GO）复合物,将其用NaBH4还原得到聚吡咯/还原氧化石墨烯(PPy/RGO)复合物,采用X射线衍射、红外光谱和场发射扫描电子显微镜（FESEM）对其结构和形貌进行物理表征。 采用循环伏安、恒电流充放电和交流阻抗等电化学方法系统研究了所制备样品的电化学性能。 实验结果表明,在电流密度为0.5 A/g、吡咯（Py）与GO质量比为95∶5时,得到的复合物还原前后比电容分别可达401.5和314.5 F/g,远高于单纯的GO（34.8 F/g）和PPy（267.5 F/g）。 经过1200圈循环稳定性测试后,PPy/RGO复合物比电容保持了原来的62.5%,与PPy和PPy/GO（电容保持率分别为16.8%和46.4%）相比,PPy/RGO表现出更好的循环稳定性能,有望成为超级电容器电极材料。     

特殊微形貌聚吡咯的合成及吸附性能

聚吡咯(PPy)是一种性能优异的导电高分子材料,近年来的研究热点集中于PPy及其复合材料在电化学方面的应用,而对于PPy复合材料的特殊微形貌以及吸附性能的关注较少。本文介绍了关于PPy微观形貌的合成方法,综述了采用硬模板和软模版法合成纤维状、管状、球状、多孔状和其他不同特殊微形貌的PPy及其复合材料,包括PPy/金属单质、PPy/金属氧化物、PPy/染料以及PPy/非金属单质等复合材料,并进一步分析了PPy及其复合材料不同形貌之间的差异,得出微形貌的差异可以影响材料性能的结论。简述了目前将PPy复合材料应用于吸附领域的报道,介绍了不同微形貌聚吡咯材料对于其吸附性能的影响,分析了特殊形貌PPy及其复合材料对染料、重金属展示出来的优良吸附性能,指出PPy复合材料在吸附领域的巨大应用前景与商业价值。     

9,10-蒽醌-2-磺酸钠盐掺杂对导电聚吡咯电容性能的促进作用

用恒电位法制成以9,10-蒽醌-2-磺酸钠盐(AQS)为掺杂阴离子的导电聚吡咯(PPy)电化学电容器电极材料,并采用循环伏安(CV)、充放电测试、电化学阻抗(EIS)等方法表征电容性质.结果表明,与高氯酸阴离子(ClO4-)掺杂的PPy相比,PPy/AQS电极材料不仅单位质量电容和电极稳定性得到提高,工作电压范围也得以扩大.在1mol·L-1的氯化钾中,工作电压为-0.6至0.6V,扫描速率为50mV·s-1时其单位质量电容达到491F·g-1,比PPy/ClO4-电极材料提高1.5倍.这是由于AQS自身良好的氧化还原活性和AQS掺杂有利于聚吡咯膜形成疏松多孔的纳米及亚微米颗粒结构而导致的.     

石墨烯/聚吡咯纳米纤维超级电容器电极材料的制备及其电化学性能

超级电容器因其具有较高的循环稳定性和较好的能量密度而成为储能器件中的研究热点,其电极材料及制备方法是决定超级电容器电化学性能的关键因素。 本文以聚环氧乙烷-聚环氧丙烷-聚环氧乙烷三嵌段共聚物(P123)为软模板,通过一步原位聚合法成功地制备了石墨烯/聚吡咯纳米纤维(GR/PPy NF)复合超级电容器电极材料。 通过X射线衍射(XRD),X射线光电子能谱(XPS)、透射电子显微镜(TEM)和傅里叶变换红外光谱仪(FT-IR)等对复合材料的结构和形态进行了系统的表征。 利用电化学方法对GR/PPy NF复合电极材料的电化学性能进行了系统的分析。 结果表明,在电流密度0.5 A/g下,纳米复合材料的比电容量高达969.5 F/g,在充放电600圈之后,仍可保留初始比电容的88%,展示了良好的电容性能及循环稳定性。 GR/PPy NF制备简单,性能优异,是一种很有前途的能量转换/存储材料。     

Preparation of conductive,flexible and transparent films by in situ deposition of polypyrrole nanoparticles on polyethylene terephthalate

In this study polypyrrole (PPy) nanoparticles were deposited as a thin film on the modified surface of polyethyleneterephthalate (PET) by in situ chemical polymerization in the presence of sodium dodecylsulfate (SDS), sodium dodecylbenzenesulfonate (DBSNa) and mixture of them as the surfactant. The surface of PET was modified by KOH before deposition and was investigated for conductivity and adhesion of PPy nanoparticles to PET. Resulting conductive flexible films were characterized by UV–Vis spectroscopy, fieldemission scanning electron microscopy, contact angle measurements and four-point-probe technique for conductivity. Direct morphological observation (FESEM) and electrical measurements indicated that the morphology, conductivity and the nature of deposited PPy films depend on surfactant, surface modification of PET and monomer concentration. In optimized process condition, uniform conductive films of PPy were obtained with good adhesion to PET.     

Improved Electrochemical Kinetic Performances of La-Mg-Ni-based Hydrogen Storage Alloy Modified by Ni-Polypyrrole Complex Surface Treatment

In order to improve the electrochemical kinetic performances of La-Mg-Ni-based alloy, complex surface modification of Ni with excellent catalytic activity and conducting polymer polypyrrole(PPy) was performed via electroless plating method. FESEM images revealed that the complex Ni-PPy treatment resulted in more micropores at the alloy surface, with Ni particles and cotton fiber-shape PPy microspheres attached. Both the larger surface area induced by the micropore and the higher catalytic activity and conductivity on account of the dispersed Ni particles/PPy microspheres promoted the electrode reaction, thereby increasing the discharge capacity of the modified alloy electrode. Electrochemical impedance spectroscopy(EIS) and linear polarization results showed that the Ni-PPy treatment decreased the charge-transfer resistance and increased the exchange current density greatly, far more than the single-component Ni or PPy treatment. Consequently, a notable improvement in high rate dischargeability(HRD) was observed, and at a high discharge current density of 1800 mA/g, the HRD of the modified electrode increased by 10.4% compared with that of the bare electrode.     

Paper-like free-standing polypyrrole and polypyrrole–LiFePO4 composite films for flexible and bendable rechargeable battery

Highly flexible, paper-like, free-standing polypyrrole and polypyrrole–LiFePO₄ composite films were prepared using the electropolymerization method. The films are soft, lightweight, mechanically robust and highly electrically conductivity. The electrochemical behavior of the free-standing films was examined against lithium counter electrode. The electrochemical performance of the free-standing pure PPy electrode was improved by incorporating the most promising cathode material, LiFePO₄, into the PPy films. The cell with PPy–LiFePO₄ composite film had a higher discharge capacity beyond 50 cycles (80 mA h/g) than that of the cell with pure PPy (60 mA h/g). The free-standing films can be used as electrode materials to satisfy the new market demand for flexible and bendable batteries that are suitable for the various types of design and power needs of soft portable electronic equipment.     

Templateless synthesis of polypyrrole nanowires by non-static solution-surface electropolymerization

Polypyrrole nanowires (PPy-NWs) are synthesized by a novel templateless approach based on non-static solution-surface (NSSS) electropolymerization. The mechanism responsible for PPy-NW formation is the simultaneous oxidation of pyrrole and water, with concomitant formation of hydroxyl radicals and dioxygen nanobubbles. In particular, a localized PPy-NW deposition at the solution-air interface is enabled by solution-surface electropolymerization due to the surface excess of the monomer at the interface favored by the large surface tension of the solvent. In the proposed approach, solution-surface electropolymerization is performed in non-static conditions (NSSS), as the solution-air interface is shifted by flowing the electrolyte solution over the electrode surface. This allows a PPy-NW homogeneous deposition on whatever large area electrode to be rapidly achieved. Parameters influencing the morphology of PPy-NWs are studied, particularly focusing on flow rate, pH of the electrolyte solution, and electropolymerization time. The growth process of PPy-NWs is examined and the way of tuning their resulting morphology is discussed. Morphological investigation by scanning electron microscopy and chemical/electrochemical characterization of PPy-NWs by X-ray photoelectron spectroscopy and cyclic voltammetry, respectively, further support the proposed nanowire formation mechanism. Nanowires with diameter in the range of 40–300 nm are obtained, and the possibility of depositing differently sized nanowires with a predetermined spatial distribution on the same substrate is also demonstrated.     

Nano-polypyrrole supercapacitor arrays prepared by layer-by-layer assembling method in anodic aluminum oxide templates

A novel method for preparing nano-supercapacitor arrays, in which each nano-supercapacitor consisted of electropolymerized Polypyrrole (PPy) electrode / porous TiO₂ separator / chemical polymerized PPy electrode, was developed in this paper. The nano-supercapacitors were fabricated in the nano array pores of anodic aluminum oxide template using the bottom-up, layer-by-layer synthetic method. The nano-supercapacitor diameter was 80 nm, and length 500 nm. Based on the charge/discharge behavior of nano-supercapacitor arrays, it was found that the PPy/TiO₂/PPy array supercapacitor devices performed typical electrochemical supercapacitor behavior. The method introduced here may find application in manufacturing nano-sized electrochemical power storage devices in the future for their use in the area of microelectronic devices and microelectromechanical systems.     

Layer-by-layer engineered Co-Al hydroxide nanosheets/graphene multilayer films as flexible electrode for supercapacitor

Multilayer films of Co-Al layered double hydroxide nanosheets (Co-Al LDH-NS) and graphene oxide (GO) were fabricated through layer-by-layer (LBL) assembly. By using a three-electrode system, the electrochemical performances of the films were investigated to evaluate their potential as electrode materials to be used in flexible supercapacitor devices. The Co-Al LDH-NS/GO multilayer films exhibited a high specific capacitance of 880 F/g and area capacitance of 70 F/m(2) under the scan rate of 5 mV/s. And the film exhibited good cycle stability over 2000 cycles. After treating the films at 200 °C in H(2) atmosphere, the specific capacitance and area capacitance were largely increased up to 1204 F/g and 90 F/m(2) due to partial reduction of GO. A flexible electrode by depositing Co-Al LDH-NS/GO multilayer film onto PET substrate was prepared to show the potential of Co-Al LDH-NS/GO films for flexible energy storage.     

BC/CoNi2S4@PPy柔性复合电极材料的制备及电化学性能

本文采用溶剂热、原位聚合和真空抽滤相结合的方法制备了用于超级电容器的细菌纤维素/镍钴硫化物/聚吡咯(BC/CoNi2S4@PPy)柔性电极材料,通过X 射线衍射、场发射扫描电镜、红外光谱、氮气吸脱附、拉伸强度和接触角表征了材料的形貌结构、组成、机械性能和亲水性,并采用循环伏安法和恒电流充放电测试了复合材料的电化学性能....     

Flexible NH3 sensors fabricated by in situ self-assembly of polypyrrole

Novel flexible NH₃ gas sensors were formed by the in situ self-assembly of polypyrrole (PPy) on plastic substrates. A negatively charged substrate was prepared by the formation of an organic monolayer (3-mercapto-1-propanesulfonic acid sodium salt—MPS) on a polyester (PET) substrate using a pair of comb-like Au electrodes. Two-cycle poly(4-styrenesulfonic acid) sodium salt/poly(allylamine hydrochloride) (PSS/PAH) bilayers (precursor layer) were then layer-by-layer (LBL) deposited on an MPS-modified substrate. Finally, a monolayer of PPy self-assembled in situ and PPy multilayer thin films self-assembled LBL in situ on a (PSS/PAH)₂/MPS/Au/Cr/PET substrate. The thin films were analyzed by atomic force microscopy (AFM). The effects of the precursor layer (PSS), the deposition time of the monolayer of PPy and the number of PPy multilayers on the gas sensing properties (response) and the flexibility of the sensors were investigated to optimize the fabrication of the film. Additionally, other sensing properties such as sensing linearity, reproducibility, response and recovery times, as well as cross-sensitivity effects were studied. The flexible NH₃ gas sensor exhibited a strong response that was comparable to or even greater than that of sensors that were fabricated on rigid substrate at room temperature.     

Polymerization of pyrrole induced by pillar[5]arene functionalized graphene for supercapacitor electrode

Conducting polymer is an important electrode material for supercapacitors because of its high initial specific capacitance. Herein, a novel nanocomposite composed of polypyrrole (PPy) film homogeneously immobilized on the pillar[5]arene functionalized reduced graphene oxide nanosheets (RGO-HP5A-PPy) was successfully prepared. RGO-HP5A induced pyrrole to polymerize on the graphene surface and the specific capacitance loss caused by PPy agglomeration was avoided. Noticeably, the specific capacitance of RGO-HP5A-PPy was up to 495 F/g at 1 A/g. Compared with pure PPy (319 F/g), the specific capacitance was increased by 55%. The specific capacitance retention of the assembled symmetric supercapacitor reached 76% after 10,000 cycles at 5 A/g. This study gave full play to the advantages of pillar[5]arene, graphene and PPy, and was expected to promote the development of supramolecular functionalized composites in energy storage.