后处理法合成高热稳定性的中孔Ti-P-Al材料

 以阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)为模板剂,采用水热合成法制备了中孔氧化钛原粉,再采用磷酸和氯化铝溶液依次对中孔氧化钛原粉进行后处理,得到了具有高热稳定性的中孔Ti-P-Al材料. 通过粉末X射线衍射、透射电子显微镜和氮物理吸附等方法对样品进行了表征. 结果表明,反应凝胶组成对样品的中孔结构有较大的影响,当反应凝胶配比为Ti(SO4)2∶CTAB∶H2O=1∶0.54∶430, 温度为363 K, 处理时间为10～20 min时,所得的TiO2原粉具有较规整的中孔结构. 此样品经过0.25 mol/L的磷酸处理后有序性有较大程度的提高. 将磷酸处理过的样品进一步用氯化铝溶液处理,得到了中孔结构的Ti-P-Al材料,此材料经过873 K焙烧后仍具有典型的中孔特征,其比表面积为 382 m2/g, 孔径为3.13 nm.     

高热稳定性Cu-Mn-O催化燃烧催化剂的制备

采用共沉淀法制备Cu-Mn-O前驱体, 以水洗和醇洗的方式去除杂质, 在空气气氛下干燥焙烧获得催化剂. 用BET、 XRD、 SEM对此催化剂的比表面积、晶相结构以及颗粒形貌进行了表征, 并以甲苯催化燃烧为探针反应考察了催化剂的性能. 结果表明, 在500 ℃焙烧, Cu-Mn-O催化剂的比表面积可以达到67.9 m2/g, 颗粒尺寸在100 nm左右并高度分散. 与水洗样品相比, 醇洗样品的活性相CuMn2O4热稳定性得到较大提高, 经700 ℃焙烧的Cu-Mn-O上甲苯完全燃烧温度降低了60 ℃;800 ℃焙烧后, 甲苯完全燃烧温度降低了约50 ℃.     

Si掺杂介孔SO_4~(2-)/TiO_2的非模板剂法合成及表征

在不使用模板剂的条件下,以工业硫酸氧钛溶液为原料合成介孔偏钛酸前驱体,再经正硅酸乙酯浸渍焙烧制备了具有良好热稳定性的Si掺杂介孔SO42-/TiO2.采用X射线衍射、N2吸附-脱附、扫描电镜、X射线能谱和傅里叶变换红外光谱等表征方法对样品的组成和结构进行了分析,并考察了该材料在亚甲基蓝氧化降解反应中的光催化性能.结果表明,在焙烧过程中,被吸附在偏钛酸孔道内的正硅酸乙酯发生水解,并与偏钛酸孔壁上的自由羟基形成Ti-O-Si键;Si进入二氧化钛骨架中,对孔结构起到了支撑作用,从而提高了介孔SO42-/TiO2的热稳定性.700℃焙烧2 h后,Si掺杂介孔SO42-/TiO2材料的比表面积仍达到189 m2/g,平均孔径为2.8 nm.400℃焙烧的样品在亚甲基蓝降解反应中表现出较好的光催化活性.     

低温固相法制备高比表面积的纳米MgO

 以草酸和乙酸镁为原料,采用低温固相化学反应合成出前体MgC2O4·2H2O, 再通过焙烧得到纳米MgO. 采用X射线衍射、 N2物理吸附、透射电镜和热重-差热技术对前体和MgO样品进行了表征,并考察了焙烧气氛的影响. 结果表明,在流动干燥的氮气中520 ℃焙烧4 h后制得了比表面积高达412 m2/g的纳米MgO; 此MgO为面心立方结构,晶粒尺寸为4～5 nm, 粒子堆积成在一定程度上长程有序的介孔结构,并具有十分优良的抗高温烧结性能, 600和800 ℃焙烧2 h后,其比表面积仍分别高达357和153 m2/g.     

高比表面纳米MgO的制备及其影响因素研究

在溶液中采用不同的原料制备了三种前体MgC2O4•2H2O, 经高温焙烧得到高比表面MgO. 用XRD、BET、TEM和TG-DTA等表征手段对前体及产物MgO进行了表征. 结果表明, 以醋酸镁和草酸为原料制备前体草酸镁并在焙烧过程中消除水汽的影响是得到高比表面MgO的关键. 最优条件下制备的样品经520 ℃焙烧后比表面积高达534 m2•g−1, 晶粒尺寸仅为4～5 nm的MgO粒子堆积成一定程度上长程有序的介孔结构, 并具有十分优良的抗高温烧结性能. 650 ℃和800 ℃焙烧2 h后, 其比表面积仍分别高达229 m2•g−1和134 m2•g−1.     

以MCM-22为原料合成高水热稳定性的介孔材料

以合成的微孔分子筛MCM-22为原料,将其与表面活性剂及氢氧化钠一起回流溶解,再调节溶液的pH值至7～9, 使MCM-22转化为高水热稳定性的介孔材料. 所得介孔材料具有蠕虫状的均匀孔道,骨架中不含有MCM-22的微观结构单元. 该介孔材料至少含有18%的表面活性剂,经823 K焙烧脱除表面活性剂后,其孔径为2 2 nm, 比表面积为 1 038 m2/g, 孔容为0 97 cm3/g. 焙烧后的介孔材料具有非常高的水热稳定性,经沸水回流100 h后其比表面积为896 m2/g, 孔容为0 90 cm3/g, 孔径为2 1 nm, 即使经过300 h的回流,该材料仍能保持698 m2/g的比表面积和0 90 cm3/g的孔容. 固体 29Si MAS NMR结果表明,该介孔材料的高水热稳定性与其高表面缩合度有关.     

Si掺杂介孔SO2-4/TiO2的非模板剂法合成及表征

在不使用模板剂的条件下,以工业硫酸氧钛溶液为原料合成介孔偏钛酸前驱体,再经正硅酸乙酯浸渍焙烧制备了具有良好热稳定性的Si掺杂介孔SO2-4/TiO2.采用X射线衍射、N2吸附-脱附、扫描电镜、X射线能谱和傅里叶变换红外光谱等表征方法对样品的组成和结构进行了分析,并考察了该材料在亚甲基蓝氧化降解反应中的光催化性能.结果表明,在焙烧过程中,被吸附在偏钛酸孔道内的正硅酸乙酯发生水解,并与偏钛酸孔壁上的自由羟基形成 Ti - O - Si 键;Si进入二氧化钛骨架中,对孔结构起到了支撑作用,从而提高了介孔SO2-4/TiO2的热稳定性.700 ℃焙烧 2 h 后,Si掺杂介孔SO2-4/TiO2材料的比表面积仍达到189 m2/g,平均孔径为2.8 nm.400 ℃焙烧的样品在亚甲基蓝降解反应中表现出较好的光催化活性.     

碱液回流老化制备高表面积二氧化锆

 回流老化由ZrOCl2水解得到的ZrO（OH）2水凝胶，然后经焙烧制\r\n备了高比表面积的ZrO2．采用氮吸附、X射线衍射和FT－Raman光谱等技\r\n术，研究了老化温度、老化时间、碱液的碱度和搅拌速度以及焙烧气氛\r\n对ZrO2比表面积、晶相组成和晶粒大小的影响．结果表明，回流老化可\r\n明显提高ZrO2的比表面积和耐热性．用比色法分析了样品中Si4＋杂质\r\n的含量，结果表明，回流老化引起二氧化锆比表面积和热稳定性增大的\r\n主要原因是热碱溶液使玻璃容器中的Si4＋溶解并掺杂至ZrO2．样品中\r\nSi4＋杂质含量愈大，ZrO2的比表面积和热稳定性愈高，ZrO2的晶粒愈\r\n小．将ZrO（OH）2水凝胶在pH＝11．5的NH4OH溶液中于96℃回流老化2\r\n4h，再经600℃焙烧可获得比表面积高达305m2／g的无定形ZrO2；经80\r\n0℃焙烧可制得晶粒为5．2nm，比表面积为174m2／g的四方晶相ZrO2．     

多孔二氧化钛微球的制备、表征及其光催化性能

以Lutensol TO(异构十三醇聚氧乙烯醚)系列非离子表面活性剂为辅助剂,采用溶胶-凝胶法制备了比表面积高、孔径分布窄的锐钛矿型TiO2多孔微球,并用透射电镜、扫描电镜、热重-差热分析、X射线衍射和氮吸附进行了表征.以亚甲基蓝降解为模型反应评价了其光催化性能,并与商品化TiO2Degussa P25进行了比较.实验结果表明,样品在425℃焙烧后,形成具有孔状结构的锐钛矿型TiO2微球,粒径为0.7~1.0μm,比表面积为70.5 m2/g,总孔容为0.12 cm3/g,平均孔径为4.26nm,晶粒尺寸为12 nm.这种多孔TiO2微球具有较高的催化活性,与Degussa P25纳米TiO2的催化活性相当.     

Ag担载介孔Pb3Nb2O8光催化剂的制备及其增强的可见光催化活性表征

光催化技术在环境净化方面,尤其是降解有机污染物应用上表现出潜在价值.可见光响应型光催化剂具有优异的光吸收特性和高的光催化活性,因而备受人们关注并被大量研究.Pb3Nb2O8光催化剂由于其自身的稳定性以及对可见光响应的能力是一种潜在的高效光催化材料.但是,有报道表明Pb3Nb2O8光催化剂对可见光降解有机物活性较低,这主要归因于它较小的比表面积以及较高的电子-空穴复合率.为了解决这个问题,本文采用蒸发自组装技术制备了大比表面积的介孔Pb3Nb2O8,采用光沉积方式在介孔Pb3Nb2O8上负载了均匀分散的纳米Ag颗粒,并对不同焙烧温度、载Ag量以及进一步的热处理对光催化活性的影响作了深入研究.XRD结果表明,在400℃和500℃焙烧条件下获得的样品属于Pb3Nb2O8相,600℃焙烧使得介孔Pb3Nb2O8发生相变.氮气吸附-脱附表征表明,升高焙烧温度使样品比表面积从最大69 m2/g(400℃)减小到19 m2/g(600℃).透射电子显微镜分析结果表明,所获得样品具有蠕虫状介孔孔道结构,并且Ag纳米颗粒均匀分散在介孔Pb3Nb2O8表面.紫外-可见吸收光谱表明,介孔Pb3Nb2O8的吸收边拖尾到530-550 nm,担载Ag之后光吸收发生显著变化,光吸收拓展到700 nm.光催化活性测试采用可见光催化氧化脱氢异丙醇气体至丙酮反应.结果表明,在420 nm以上可见光照射下,1 h内的光催化反应过程中,采用高温固态反应制备的Pb3Nb2O8上丙酮生成速率为2.9 ppm/min,而介孔Pb3Nb2O8催化剂上最高可达55.5 ppm/min.介孔Pb3Nb2O8负载Ag之后,400℃焙烧的介孔Pb3Nb2O8光催化活性显著提高,降解速率达120.7 ppm/min.通过介孔Pb3Nb2O8和固相合成Pb3Nb2O8的光催化活性对比发现,大比表面积样品的光催化活性显著提高.这可归结为大的比表面积提供了大量的催化反应活性位点,从而提高了光催化反应活性,此外介孔材料的孔壁结构为纳米结构,有利于光生电子-空穴传输到表面参加反应.担载Ag后介孔Pb3Nb2O8的光催化活性进一步提高,主要是因为助催化剂Ag纳米颗粒促进了光生电子-空穴分离,延长了载流子寿命,从而提高了光催化活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.