A structural influence on the electrical double-layer characteristics of Al4C3-derived carbon

Several carbon materials were produced by reacting aluminum carbide with chlorine gas at different temperatures (400–900 °C). Chlorination temperature and porosity values showed the inversely related trends whereby the graphitization degree rises with the chlorination temperature. Electrochemical measurements performed in three-electrode test cells with 1.0-M Et₃MeNBF₄ electrolyte revealed that the changes in porosity parameters and the degree of graphitization are in good correlation with specific capacitance values. Capacitance depends on the structure of carbon and varies in studied chlorination range from 109 to 60 F g⁻¹ and from 114 to 64 F g⁻¹ for the negatively and positively charged electrode materials, respectively. An exceptionally low capacitance was observed for the material produced at 700 °C that was explained by the multiwall carbon nanobarrels and the highly ordered curved graphitic flakes, which have low specific surface and possess the relatively low specific surface-related capacitance.     

High-performance supercapacitors of hydrous ruthenium oxide/mesoporous carbon composites

The amorphous hydrous ruthenium oxide/mesoporous carbon composites (denoted as RuO₂·xH₂O/MC), obtained by loading small amount of amorphous hydrous ruthenium oxide nanoparticles ranged from 0.9 to 5.4% by weight of Ru (denoted as RuO₂·xH₂O) on mesoporous carbon (MC), were investigated for the first time and were used for supercapacitors. Electrochemical measurements showed that RuO₂·xH₂O/MC composites not only have an enhanced specific capacitance but also retain the superior rate capability of MC. The RuO₂·xH₂O/MC composite with Ru loading of 3.6 wt% exhibited an increase of the specific capacitance of approximately 57% (from 115 to 181 F/g) at the scan rate of 25 mV s⁻¹ in 0.1 M H₂SO₄ aqueous electrolyte. The specific capacitance based on the mass of RuO₂ was estimated to be 1,527 F/g, by subtracting the contribution from MC in the composite. Cycle performance tests for RuO₂·xH₂O/MC composite (3.6 wt% Ru) showed that approximately 2.8% loss of the total capacitance was observed after 1,000 cycles.     

Electropolymerized composite film of polypyrrole and functionalized multi-walled carbon nanotubes: effect of functionalization time on capacitive performance

The composite film of polypyrrole and functionalized multi-walled carbon nanotubes (PPy/F-MWNTs) was prepared by electropolymerization. MWNTs were functionalized by sonicating with a concentrated solution of H₂SO₄/HNO₃ (3/1, volume ratio) in a water bath for different times. The carbon nanotubes (CNTs) are cut into smaller portions with more functional groups introduced on their surface when the sonicating time (nominated as functionalization time hereafter) is increased. However, the specific capacitance of the composite film reaches a maximum of 240 F g⁻¹ at the scanning rate of 10 mV s⁻¹ when MWNTs are functionalized for 24 h, which is about 205 F g⁻¹, 225 F g⁻¹ and 232 F g⁻¹, respectively, when MWNTs are functionalized for 6 h, 12 h and 48 h. At a current load of 1.0 A g⁻¹, PPy/F-MWNT composite film functionalized for 24 h (PPy/F-MWNTs (24 h)) retains 93.49% of its initial capacitance after 1,000 cycles of galvanostatic charge/discharge, and the discharge efficiency is higher than 98.15% during cycling. High specific capacitance, good rate performance, fast charge/discharge ability and long cycling life are ascribed to the synergistic effect of the two components to form a porous composite film as well as the easy accessibility of counter ions into the film. Therefore, PPy/F-MWNT (24 h) composite film is a kind of promising electrode material for supercapacitors. The mechanism of underfunctionalization and overfunctionalization of carbon nanotubes is also discussed.     

Influence of addition of cobalt oxide on microstructure and electrochemical capacitive performance of nickel oxide

Ni–Co oxide nanocomposite was prepared by thermal decomposition of the precursor obtained via a new method—coordination homogeneous coprecipitation method. The synthesized sample was characterized physically by X-ray diffraction, scanning electron microcopy, energy dispersive spectrum, transmission electron microscope, and Brunauer–Emmett–Teller surface area measurement, respectively. Electrochemical characterization of Ni–Co oxide electrode was examined by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance measurements in 6-mol L⁻¹ KOH aqueous solution electrolyte. The results indicated that the addition of cobalt oxide not only changed the morphology of NiO but also enhance its electrochemical capacitance value. A specific capacitance value of 306 F g⁻¹ of Ni–Co oxide nanocomposite with n _Co = 0.5 (n _Co is the mole fraction of Co with respect to the sum of Co and Ni) was measured at the current density of 0.2 A g⁻¹, nearly 1.5 times greater than that of pure NiO electrode. Lower resistance and better rate capability can also be observed.     

RuO2/Co3O4 thin films prepared by spray pyrolysis technique for supercapacitors

RuO₂/Co₃O₄ thin films with different RuO₂ content were successfully prepared on fluorine-doped tin oxide coated glass plate substrates by spray pyrolysis method, and their capacitive behavior was investigated. Electrochemical property was performed by cyclic voltammetry, constant current charge/discharge, and electrochemical impedance spectra. The capacitive performance of RuO₂/Co₃O₄ thin films with different RuO₂ content corresponded to a contribution from a main pseudocapacitance and an additional electric double-layer capacitance. The specific capacitance of pure Co₃O₄, 15.5%, 35.6%, and 62.3% RuO₂ composites at the current density of 0.2 A g⁻¹ were 394 ± 8, 453 ± 9, 520 ± 10, and 690 ± 14 F g⁻¹, respectively; 62.3% RuO₂ composite presented the highest specific capacitance value at various current densities, whereas 35.6% RuO₂ composite exhibited not only the largest specific capacitance contribution from RuO₂ (C _sp ^RuO2) at the current density of 0.5, 1.0, 1.5, and 2.0 A g⁻¹ but also the highest specific capacitance retention ratio (46.3 ± 2.8%) at the current density ranging from 0.2 to 2.0 A g⁻¹. Electrochemical impedance spectra showed that the contact resistance dropped gradually with the decrease of RuO₂ content, and the charge-transfer resistance (R _ct) increased gradually with the decrease of RuO₂ content.     

The preparation of PANI/CA composite electrode material for supercapacitors and its electrochemical performance

Polyaniline (PANI)/carbon aerogel (CA) composite electrode materials were prepared by chemical oxidation polymerization. The morphology of PANI/CA composite was examined by scanning electron microscopy. The results showed that PANI was uniformly deposited onto the surface of porous CA and filled big inner pores of the CA. Electrochemical performance of the composite electrode was studied by cyclic voltammograms and galvanostatic charge/discharge measurements. The results indicated that the PANI/CA composite electrode had much better electrochemical performance, high reversibility, and high charge/discharge properties than CA. Moreover, the results based on cyclic voltammograms showed that the composite material has a high specific capacitance of 710.7 F g⁻¹, while the capacitance of CA electrode was only 143.8 F g⁻¹. Besides, the supercapacitor using the PANI/CA composite as electrode active material showed a stable cycle life in the potential range of −0.2–0.8 V.     

Structural and electrochemical behavior of Mn–V oxide synthesized by a novel precipitation method

Manganese–vanadium oxide had been synthesized by a novel simple precipitation technique. Scanning electron microscopy, X-ray diffraction, Brunauer–Emmett–Teller, thermogravimetric analysis/differential scanning calorimetry, and X-ray photoelectron spectroscopy were used to characterize Mn–V binary oxide and δ-MnO₂. Electrochemical capacitive behavior of the synthesized Mn–V binary oxide and δ-MnO₂ was investigated by cyclic voltammetry, galvanostic charge–discharge curve, and electrochemical impedance spectroscope methods. The results showed that, by introducing V into δ-MnO₂, the specific surface area of the mixed oxide increased due to a formation of small grain size. The specific capacitance increased from 166 F g⁻¹ estimated for MnO₂ to 251 F g⁻¹ for Mn–V binary oxide, and the applied potential window extended to −0.2–1.0 V (vs. saturated calomel electrode). Through analysis, it is suggested that the capacitance performance of Mn–V binary oxide materials may be improved by changing the following three factors: (1) small grain and particle size and large activity surface area, (2) appropriate amount of lattice water, and (3) chemical state on the surface of MnO₂ material.     

Preparation and electrochemical performance of activated carbon thin films with polyethylene oxide-salt addition for electrochemical capacitor applications

The effect of polymer–salt addition in the activated carbon electrode for electric double-layer capacitor (EDLC) has been investigated. A series of composite thin film electrode consisting of activated carbon, carbon black, polytetrafluoroethylene and polymer–salt complex (polyethyleneoxide–LiClO₄) with an appropriate weight ratio were prepared and examined their performance for EDLCs using 1 mol L⁻¹ LiClO₄ in ethylene carbonate:diethylcarbonate electrolyte solution. The electrochemical capacitance performances of these electrodes with different compositions were characterized by cyclic voltammetry, galvanostatic charge–discharge cycling, and AC impedance measurements. By comparison, the best results were obtained with a composite electrode rich in polymer–salt additive (132 F g⁻¹ at 100 mA g⁻¹ of galvanostatic experiment). In general, the polymer–salt-containing electrode had shown improved performance over activated carbon electrodes without polymer–salt at high current density.     

Electrochemical performance of Co–Al layered double hydroxide nanosheets mixed with multiwall carbon nanotubes

Regular hexagonal Co–Al layered double hydroxides (Co–Al LDH) were synthesized by urea-induced homogeneous precipitation. This material proved to be nanosheets by scanning electron microscopy and X-ray diffraction measurements. The electrochemical capacitive behavior of the nanosheets in 1 M KOH solution were evaluated by constant current charge/discharge and cyclic voltammetric measurements, showing a large specific capacitance of 192 F·g⁻¹ even at the high current density of 2 A·g⁻¹. When multiwall carbon nanotubes (MWNTs) were mixed with the Co–Al LDH, it was found that the specific capacitance and long-life performance of all composite electrodes at high current density are superior to pure LDH electrode. When the added MWNTs content is 10 wt%, the specific capacitance increases to 342.4 F·g⁻¹ and remains at a value of 304 F·g⁻¹ until the 400th cycle at 2 A·g⁻¹, showing that this is a promising electrode material for supercapacitors working at heavy load. According to the electrochemical impedance spectra, MWNTs greatly increase the electronic conductivity between MWNTs and the surface of Co–Al LDH, which consequently facilitates the access of ions in the electrolyte and electrons to the electrode/electrolyte interface.     

Study of capacitive properties in supercapacitor for copolymer of aniline with m-phenylenediamine

The copolymers were synthesized with different molar ratios of m-phenylenediamine to aniline (R for short) by a chemical oxidation method. The products were first used as electrochemical activity materials of the supercapacitor. Capacitive behaviors of the prepared copolymers in 1 mol·L⁻¹ H₂SO₄ electrolyte were examined by electrochemical impedance spectroscopy, cyclic voltammeter, and galvanostatic charge/discharge. The relationship of molar ratios with capacitive property of the prepared products was investigated too. The results showed that the product with R of 2:98 displayed better electrochemical properties than that of the other products. Compared with the synthesized polymer in the absence of m-phenylenediamine, the polymerized copolymer with R of 2:98 exhibited the initial specific capacitance value of 475 F·g⁻¹, which increased by nearly 10.1% than that of the former at a current density of 200 mA·g⁻¹ in 1 mol·L⁻¹ H₂SO₄ electrolyte in the potential range of −0.3 to 0.7 V. The discharge specific capacitance value of the copolymer remained 300 F·g⁻¹ after 1,000 cycles, exhibiting a good cycling performance and the structure stability.     

Carbon nanotube arrays supported manganese oxide and its application in electrochemical capacitors

Manganese oxide (MnO_x) has been coated on carbon nanotubes (CNTs) and fabricated as the electrodes for electrochemical capacitors (ECs) by cathodic electrodeposition. In the process, randomly oriented CNT arrays are grown directly onto the Ti/Si substrates by chemical vapor deposition method. Potentiostatic method has been utilized for cathodic electrodeposition of MnO_x onto the surface of CNTs while immersed in KMnO₄ solution. The highly porosity and fibrous microstructure of the as-prepared MnO_x/CNT electrode is beneficial for the electrolyte access to the active material, whereas CNTs provide improved electronic conductivity. Electrochemical investigations show that the increase in the loading mass of MnO_x results in a significant reduction in the specific capacitances (SCs) of the MnO_x/CNT electrodes. The MnO_x/CNT electrode with MnO_x loading mass of 50 μg shows a high SC of 400 F g⁻¹ with good long cycle stability at a current density of 10 A g⁻¹, suggesting its potential application in ECs.     

Electrochemical capacitance of nickel oxide nanotubes synthesized in anodic aluminum oxide templates

Nickel oxide (NiO) nanotubes for supercapacitors were synthesized by chemically depositing nickel hydroxide in anodic aluminum oxide templates and thermally annealing at 360 °C. The synthesized nanotubes have been characterized by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The capacitive behavior of the NiO nanotubes was investigated by cyclic voltammetry, galvanostatic charge–discharge experiment, and electrochemical impedance spectroscopy in 6 M KOH. The electrochemical data demonstrate that the NiO nanotubes display good capacitive behavior with a specific capacitance of 266 F g⁻¹ at a current density of 0.1 A g⁻¹ and excellent specific capacitance retention of ca. 93% after 1,000 continuous charge–discharge cycles, indicating that the NiO nanotubes can become promising electroactive materials for supercapacitor.     

Hybrid materials for supercapacitor application

In the present study, a manganese oxide obtained by the acid treatment of LiMn₂O₄ spinel has been used as a positive electrode of supercapacitor. Removal of lithium from a spinel allowed to obtain MnO₂ compound with the pores partly distributed in atomic scale, hence, an efficient use of its pseudocapacitive properties could be reached. On the other hand, residual lithium remaining in the structure preserved layered framework of MnO₂ with pathways for ions sorption. Physical properties, morphology, and specific surface area of electrode materials were studied by scanning and transmission electron microscopy, and nitrogen sorption measurements. Voltammetry cycling, galvanostatic charge/discharge, and impedance spectroscopy measurements performed in two- and three-electrode cells have been applied in order to measure electrochemical parameters. Neutral Li₂SO₄ aqueous solution has been selected for electrolytic medium. Extension of operating voltage for supercapacitor has been realized through asymmetric configuration with an activated carbon as a negative electrode. The asymmetric capacitor was operating within a voltage range up to 2.5 V (limited to 2.0 V for cycling tests) and was able to deliver a specific capacitance of 60 Fg⁻¹ per capacitor at 100 mA g⁻¹ current density. High specific energy of 36 Wh kg⁻¹ was reached but with a moderate power density.     

Synthesis and supercapacitance of flower-like Co(OH)<Subscript>2</Subscript> hierarchical superstructures self-assembled by mesoporous nanobelts

A facile hydrothermal strategy was first proposed to synthesize flower-like Co(OH)₂ hierarchical microspheres. Further physical characterizations revealed that the flower-like Co(OH)₂ microspherical superstructures were self-assembled by one-dimension nanobelts with rich mesopores. Electrochemical performance of the flower-like Co(OH)₂ hierarchical superstructures were investigated by cyclic voltammgoram, galvanostatic charge–discharge and electrochemical impedance spectroscopy in 3 M KOH aqueous electrolyte. Electrochemical data indicated that the flower-like Co(OH)₂ superstructures delivered a specific capacitance of 434 F g⁻¹ at 10 mA cm⁻² (about 1.33 A g⁻¹), and even kept it as high as 365 F g⁻¹ at about 5.33 A g⁻¹. Furthermore, the SC degradation of about 8% after 1,500 continuous charge–discharge cycles at 5.33 A g⁻¹ demonstrates their good electrochemical stability at large current densities.     

Electrochemical performance of LiVPO<Subscript>4</Subscript>F/C composite cathode prepared through amorphous vanadium phosphorus oxide intermediate

LiVPO₄F/C composites with better electrochemical performance were prepared by calcination of LiF and amorphous vanadium phosphorus oxide (VPO) intermediate synthesized by a sol–gel method using H₃PO₄, V₂O₅ and citric acid as raw materials. The properties of LiVPO₄F/C composites were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The analysis of XRD patterns and Fourier transform infrared spectra (FTIR) reveal that VPO intermediate prepared by sol–gel method is amorphous and VPO₄ may exist in VPO intermediate. The compositions of LiVPO₄F/C composites are related to the calcination temperature for preparation of amorphous VPO/C intermediate and LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C consists of a single crystal phase of LiVPO₄F. The electrochemical tests show that LiVPO₄F/C composite prepared by VPO/C synthesized at 700°C exhibits higher discharge capacity and excellent cycle performance. This LiVPO₄F/C composite displays discharge capacity of 133 mAh g⁻¹ at 0.5 C (78 mA g⁻¹) and remains capacity retention of 96.8% after 30 cycles, even at a high rate of 5 C, the composite exhibits high discharge capacity of 115 mAh g⁻¹ and capacity retention of 97% after 100 cycles.     

A comparative study of sequentially layer-deposited and co-deposited Co–Mn oxides as potential redox capacitors

Layers of cobalt and manganese oxides were co-deposited or deposited on top of each other or next to each other by potentiostatic method onto stainless steel substrate. Deposition potentials of 1 and −1 V for the anodic and cathodic depositions were employed. Specific capacitance values in the range of 38.5–78 F g⁻¹ were found with cobalt oxide on top of manganese oxide having the lowest and manganese oxide on top of cobalt oxide having the highest capacitances. The usefulness of the electrodes was characterized by cyclic voltammetry, charge–discharge cycling, and electrochemical impedance spectroscopy in 2 M NaOH electrolyte for redox supercapacitor applications. The latter presented the best charge/discharge behavior with no voltage drop due to lower ohmic resistance in prepared substrate; although the steadiest current observed in the course of voltammetry was due to the former. The evaluated double layer and specific capacitances for co-deposited sample according to the impedance studies were 1.75 and 47.5 F g⁻¹, respectively, being in good agreement with voltammetric measurements.     

Glycine-assisted hydrothermal synthesis of nanostructured Co x Ni1−x –Al layered triple hydroxides as electrode materials for high-performance supercapacitors

Nanostructured Co _x Ni_1−x –Al layered triple hydroxides (Co _x Ni_1−x –Al LTHs) have been successfully synthesized by a facile hydrothermal method using glycine as chelating agent. The samples were characterized by X-ray diffraction, thermogravimetry, Fourier transform infrared spectroscopy and scanning electron microscopy. The morphologies of Co _x Ni_1−x –Al LTHs varied with the Co content and its effect on the electrochemical behavior was studied by cyclic voltammetry and galvanostatic charge–discharge techniques. Electrochemical data demonstrated that the Co _x Ni_1−x –Al LTHs with Co/Ni molar ratio of 3:2 owned the best performance and delivered a maximum specific capacitance of 1,375 F g⁻¹ at a current density of 0.5 A g⁻¹ and a good high-rate capability. The capacitance retained 93.3% of the initial value after 1,000 continuous charge–discharge cycles at a current density of 2 A g⁻¹.     

Application of chitosan/iota-carrageenan polymer electrolytes in electrical double layer capacitor (EDLC)

In this work, a chitosan/iota (ι)-carrageenan blended film doped with orthophosphoric acid (H₃PO₄) as ionic dopant and poly(ethylene glycol) (PEG) as plasticizer has been used as a separator and electrolyte in an electrical double layer capacitor (EDLC). A set of samples were prepared by the solution cast technique to see the effect of the different weight ratios of the proton donor and plasticizer on the conductivity. The highest conducting sample has composition 37.50 wt.% chitosan–37.50 wt.% ι-carrageenan–18.75 wt.% H₃PO₄–6.25 wt.% PEG. The conductivity value is 6.29 × 10⁻⁴ S cm⁻¹. The conductivity–temperature relationship is Arrhenian, and the activation energy for the highest conducting sample is 0.09 eV. The specific discharge capacitance of the EDLC is 35 F g⁻¹ at 0.11 mA cm⁻² current drain and was constant for 30 cycles.     

Bi2O3 deposited on highly ordered mesoporous carbon for supercapacitors

A simple route has been employed to prepare nanosized Bi₂O₃ deposited on highly ordered mesoporous carbon. The electrochemical measurements reveal that, by loading only 10% Bi₂O₃ on the mesoporous carbon, the specific capacitance of the composite is improved by 62%, with the maximum value reaching 232 F g^?1 at a sweep rate of 5 mV s^?1. The specific capacitance of Bi₂O₃ is calculated and reaches 1305 F g^?1 at 1 mV s^?1. It is found that the mass transfer in the framework of the crystalline oxide is still difficult in spite of its nanosize, as evidenced by the decline of the specific capacitance of the Bi₂O₃ with the increase of the sweep rate. The cyclic life of composite materials is also measured and the capacitance only declines 21% after 1000 cycles.     

Immersion enthalpy and the constants of Langmuir model in the 3-chloro phenol adsorption on activated carbon

The adsorption process of 3-chloro phenol from aqueous solution on a activated carbon prepared from African palm stone and which presents a specific surface area of 685 m² g⁻¹, a greater quantity of total acid groups and a pH_PZC of 6.8 is studied. The adsorption isotherms are determined at pH values of 3, 5, 7, 9 and 11. The adsorption isotherms are fitted to the Langmuir model and the values of the maximum quantity adsorbed that are between 96.2 and 46.4 mg g⁻¹ are obtained along with the constant K_L with values between 0.422 and 0.965 L mg⁻¹. The maximum quantity adsorbed diminishes with the pH and the maximum value for this is a pH of 5. The immersion enthalpies of the activated carbon in a 3-chloro phenol solution of constant concentration, of 100 mg L⁻¹, are determined for the different pH levels, with results between 37.6 and 21.2 J g⁻¹. Immersion enthalpies of the activated carbon in function of 3-chloro phenol solution concentration are determined to pH 5, of maximum adsorption, with values between 28.3 and 38.4 J g⁻¹, and by means of linearization, the maximum immersion enthalpy is calculated, with a value of 41.67 J g⁻¹. With the results of the immersion enthalpy, maximum quantity adsorbed and the constant K_L, establish relations that describe the adsorption process of 3-chloro phenol from aqueous solution on activated carbon.