螺旋通道微流控PCR芯片连续自动扩增DNA片段的研究

研制了由内向外流动的螺旋通道微流控PCR玻璃芯片,减少了PCR反应液在微通道中流动时的分散和阻力;讨论了扩增循环数和进样速度对长片段基因扩增的影响,在26min内成功扩增了质量浓度仅为10ng/mL的6012bpλ-DNA;通过将小孔径石英毛细管作为顺序注射(SI)系统的连接管路,使其死体积降到0.30μL.实现了微升级样品的自动换样、连续PCR扩增和微通道洗涤等功能.样品间无交叉污染.每小时可扩增500bpλ-DNA试样7个.扩增产物片段大小和荧光强度的相对标准偏差分别为0.4%和6.7%.     

基于毛细管电泳的环介导恒温扩增技术检测方法研究

以大肠杆菌(E.coli)为对象,采用环介导恒温扩增技术(LAMP)对其扩增,在实验室自制的毛细管电泳-诱导荧光平台上建立了LAMP产物的检测新方法。引物F3,B3,FIP,BIP扩增的E.coli LAMP产物大小为240 bp。优化的毛细管电泳条件为:毛细管有效长度/总长度(10 cm/15 cm),筛分介质溶液为0.5%羟乙基纤维素(1 300 K),电场强度(100 V/cm),进样条件(100 V/cm,1.0 s)。毛细管电泳时,DNA长度在100~500 bp范围内与其迁移时间呈线性关系,相关系数为0.996。在相同毛细管电泳条件下对E.coli LAMP产物进行分析,并利用这种线性关系在电泳图中对E.coli LAMP产物与假阳性产物做区分,结果表明,毛细管电泳技术不仅可在15 min内实现LAMP产物及附加产物的快速检测,而且可快速区分LAMP阳性及假阳性实验产物。采用建立的毛细管电泳快速检测LAMP产物的方法,对AB0174 E.coli基因实施了LAMP,结果表明该方法适合DNA LAMP产物的快速检测。     

集成核酸提取的实时荧光PCR微全分析系统

集成核酸提取的实时荧光PCR微全分析系统将核酸提取、PCR扩增与实时荧光检测进行整合,在同一块微流控芯片上实现了核酸分析过程的全自动和全封闭,具有试剂用量少、分析速度快、操作简便等优点。本研究采用微机械加工技术制作集成核酸提取微流控芯片的阳极模,使用组合模具法和注塑法制作具有3D通道的PDMS基片,与玻璃基底通过等离子体键合封装成集成核酸提取芯片。构建了由微流体速度可调节(0~10 mL/min)的驱动控制装置、温控精度可达0.1℃的TEC温控平台、CCD检测功能模块等组成的微全分析系统。以人类血液裂解液为样品,采用硅胶膜进行芯片上核酸提取。系统根据设置好的时序自动执行,以2 mL/min的流体驱动速度完成20μL裂解液上样、清洗;以1 mL/min的流体驱动速度完成DNA洗脱,抽取PCR试剂与之混合注入到反应腔。提取的基因组DNA以链上内参基因GAPDH为检测对象,并以传统手工提取为对照,在该系统平台上进行PCR扩增和熔解曲线分析实验。片上PCR扩增结果显示,扩增曲线明显,Ct值分别为25.3和26.9。扩增产物进行熔解曲线分析得到的熔解温度一致,均为89.9℃。结果表明,此系统能够自动化、全封闭的在微流控芯片上完成核酸提取、PCR扩增与实时定量分析。     

毛细管电泳技术快速检测牙周病原菌

建立了毛细管电泳快速检测牙龈卟啉单胞菌(P.g)、齿垢密螺旋体(T.d)、福赛斯坦纳菌(T.f)3种牙周病病原菌种的方法。紫外分光光度法表明,采用无菌吸潮纸尖及PBS缓冲液可以实现牙周病原菌的快速有效提取。对提取的牙周病病原菌种做多聚酶链式反应(PCR)与多重PCR反应,最后以20 cm长,75μm内径的石英毛细管作为分离通道,分离电压4000 V,1.2%羟乙基纤维素(HEC,250 K)为筛分介质,牙周病病原菌菌种P.g,T.d,T.f PCR及多重PCR产物12 min内得到较好分离。结果表明,毛细管电泳与PCR技术相结合,可以实现牙周病原菌种快速鉴定,且检测限低至4.80×10-11ng/μL。方法已用于牙周病原菌菌种的快速检测。     

毛细管电泳安培法测定田基黄中的芦丁与槲皮素

建立了毛细管电泳电化学分离检测田基黄中生物活性成分芦丁和槲皮素的方法。考察了检测电极电位、缓冲液浓度、pH、运行电压和进样时间对分离的影响。以40 cm长,50μm内径的石英毛细管作为分离通道,运行缓冲液为25 mmol/L硼砂(pH 9.2)溶液,分离电压12 kV,0.3 mm直径的铂圆盘电极为检测电极,检测电位1.00 V(vs.Ag/AgCl),芦丁和槲皮素在10 min内得到良好分离。在上述实验条件下,芦丁和槲皮素分别在8.2×10-6~5.2×10-4mol/L与6.8×10-6~7.2×10-4mol/L范围内与峰面积呈良好线性关系,检出限分别为9.0×10-7mol/L(S/N=3)和4.7×10-7mol/L(S/N=3)。方法已应用于田基黄药材提取物成分分析。     

托吡卡胺对映体的毛细管电泳-方波安培分离检测

采用毛细管电泳-方波安培检测法,在熔融石英毛细管(75 μm i.d.×50 cm)中,以7 mmol/L 三羟甲基氨基甲烷(Tris)-10 mmol/L柠檬酸-2 mmol/L硼酸-15mmol/L β-环糊精 （β-CD） (pH 3.0)为电泳介质,采用重力进样,高度差为20 cm,进样时间为10 s,在分离电压为15 kV,方波平衡电位+0.8 V的条件下,实现了托吡卡胺对映体的分离检测。线性范围为5~750 μmol/L,检出限为2 μmol/L。对影响分离度的因素β-CD浓度、硼酸浓度及p     

毛细管区带电泳用于酶微反应器酶解条件的研究

将氨基酰化酶通过戊二醛固定在毛细管内壁,制备毛细管酶微反应器,用毛细管区带电泳对毛细管酶微反应器的酶解产物进行分离,以生成物的峰面积优化底物N-乙酰-DL-蛋氨酸的酶解条件。实验结果表明,在温度37℃的条件下,10μg/mL N-乙酰-DL-蛋氨酸磷酸盐缓冲溶液(pH7.5)以4μL/min的速度通过15 cm长的毛细管酶微反应器,具有良好的酶解效果。利用毛细管酶微反应器对底物N-乙酰-DL-蛋氨酸进行酶解,每天酶解5次,10天后酶活仅下降了8.66%,说明制备的毛细管酶微反应器具有良好的稳定性。     

芯片毛细管电泳中组分的迁移行为及其特征

在自组装的芯片毛细管电泳-激光诱导荧光检测装置上,以单个染料和一组荧光素异硫氰酸酯(FITC)标记的氨基酸为对象,研究了芯片毛细管电泳与传统毛细管电泳之间的差别,考察了玻璃芯片上微通道内的伏安特性以及抑制电压、进样方式和检测点的位置等对芯片毛细管电泳分离分析的影响,特别注意到了其有别于传统毛细管电泳的各种行为特征.     

一种共轴微通道反应器设计及单分散生物质聚合物微珠的可控制备

采用不同尺寸的聚四氟乙烯(PTFE)微管为内外管、玻璃毛细管(glass capillary)或聚丙烯(PP)中空纤维为内管管头设计制作了一种共轴微通道反应器(N-CAMFR).以聚乳酸(PLA)/二氯甲烷(CH2Cl2)溶液和海藻酸钠(Na-alginate)水溶液分别作为分散相,在N-CAMFR内形成O/W和W/O乳液后,收集乳液并使其中的液滴固化,制备出单分散的生物质聚合物微珠(BPM).研究了固定管头尺寸时,改变连续相的流速及表面活性剂的种类对微珠尺寸的影响.结果表明,使用N-CAMFR制备微珠,反应过程流畅,所制得的微珠粒径分布均匀,其分散系数(f)可低至2.16%;通过改变内管管头的尺寸可方便地调控N-CAMFR的尺度,与传统微通道反应器相比,降低制作成本的同时拓宽了其应用的范围,而且降低了微通道反应器堵塞的几率.为粒径范围200~800μm的单分散聚合物微珠的可控连续制备提供了快捷绿色的新方法.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.