Self-assembly of TiO2/polypyrrole nanocomposite ultrathin films and application for an NH3 gas sensor

TiO₂/polypyrrole (PPy) nanocomposite ultrathin films for NH₃ gas detection were fabricated by the in situ self-assembly technique. The films were characterized by UV–Vis absorption, FT–IR spectroscopy, and atomic force microscopy (AFM). The electrical properties of TiO₂/PPy ultrathin film NH₃ gas sensors, such as sensitivity, selectivity, reproducibility, and stability were investigated at room temperature in air as well as in N₂. The results showed that the optimum gas-sensing characteristics of TiO₂/PPy ultrathin film were obtained in the presence of 0.1?wt% colloidal TiO₂ for 20-min deposition. Compared with pure PPy thin-film sensors, the TiO₂/PPy film gas sensor has a shorter response/recovery time. It was also found that both humidity and temperature had an effect on the operation of the TiO₂/PPy film gas sensor at low NH₃ concentrations.     

Superior Photostability and Photocatalytic Activity of ZnO Nanoparticles Coated with Ultrathin TiO2 Layers through Atomic‐Layer Deposition

Atomic‐layer deposition (ALD) is a thin‐film growth technology that allows for conformal growth of thin films with atomic‐level control over their thickness. Although ALD is successful in the semiconductor manufacturing industry, its feasibility for nanoparticle coating has been less explored. Herein, the ALD coating of TiO₂ layers on ZnO nanoparticles by employing a specialized rotary reactor is demonstrated. The photocatalytic activity and photostability of ZnO nanoparticles coated with TiO₂ layers by ALD and chemical methods were examined by the photodegradation of Rhodamine B dye under UV irradiation. Even though the photocatalytic activity of the presynthesized ZnO nanoparticles is higher than that of commercial P25 TiO₂ nanoparticles, their activity tends to decline due to severe photocorrosion. The chemically synthesized TiO₂ coating layer on ZnO resulted in severely declined photoactivity despite the improved photostability. However, ultrathin and conformal ALD TiO₂ coatings (≈0.75–1.5 nm) on ZnO improved its photostability without degradation of photocatalytic activity. Surprisingly, the photostability is comparable to that of pure TiO₂, and the photocatalytic activity to that of pure ZnO.     

CdS‐Encapsulated TiO2 Nanotube Arrays Lidded with ZnO Nanorod Layers and Their Photoelectrocatalytic Applications

A novel TiO₂ nanotube array/CdS nanoparticle/ZnO nanorod (TiO₂ NT/CdS/ZnO NR) photocatalyst was constructed which exhibited a wide‐absorption (200–535 nm) response in the UV/Vis region and was applied for the photoelectrocatalytic (PEC) degradation of dye wastewater. This was achieved by chemically assembling CdS into the TiO₂ NTs and then constructing a ZnO NR layer on the TiO₂ NT/CdS surface. Scanning electron microscopy (SEM) results showed that a new structure had been obtained. The TiO₂ NTs looked like many “empty bottles” and the ZnO NR layer served as a big lid. Meanwhile the CdS NPs were encapsulated between them with good protection. After being sensitized by the CdS NPs, the absorption‐band edge of the obtained photocatalyst was obviously red‐shifted to the visible region, and the band gap was reduced from its original 3.20 eV to 2.32 eV. Photoelectric‐property tests indicated that the TiO₂ NT/CdS/ZnO NR material maintained a very high PEC activity in both the ultraviolet (UV) and the visible region. The maximum photoelectric conversion efficiencies of TiO₂ NT/CdS/ZnO NR were 31.8 and 5.98 % under UV light (365 nm) and visible light (420–800 nm), respectively. In the PEC oxidation, TiO₂ NT/CdS/ZnO NR exhibited a higher removal ability for methyl orange (MO) and a high stability. The kinetic constants were 1.77×10^?4 s^?1 under UV light, which was almost 5.9 and 2.6 times of those on pure TiO₂ NTs and TiO₂ NT/ZnO NR, and 2.5×10^?4 s^?1 under visible light, 2.4 times those on TiO₂ NT/CdS.     

Preparation and Characterization of Polypyrrole/TiO2 Coaxial Nanocables

Summary: We demonstrate in this communication that large‐scale coaxial nanocables of polypyrrole (PPy)/TiO₂ can be obtained via three steps: (1) synthesis of TiO₂ nanofibers by electrospinning; (2) physical adsorption Fe³⁺ oxidant on the surface of TiO₂ nanofibers; (3) followed by polymerization of pyrrole (from vapor) on the surface of TiO₂ nanofibers. During the synthesis, the PPy formed on TiO₂ nanofibers as a template and formed PPy/TiO₂ coaxial nanocables. TEM image proved that PPy (20 nm thickness) covered the surface of TiO₂ nanofibers. Fourier‐transform infrared (FTIR), X‐ray photoelectron spectra (XPS), and X‐ray diffraction patterns (XRD) characterized the chemical structure of the coaxial nanocables. Surface photovoltage spectroscopy (SPS) revealed the surface properties of the PPy/TiO₂ coaxial nanocables.

TEM image of individual PPy/TiO₂ coaxial nanocable.     

Highly Efficient Low‐Temperature Plasma‐Assisted Modification of TiO2 Nanosheets with Exposed {001} Facets for Enhanced Visible‐Light Photocatalytic Activity

Anatase TiO₂ nanosheets with exposed {001} facets have been controllably modified under non‐thermal dielectric barrier discharge (DBD) plasma with various working gas, including Ar, H₂, and NH₃. The obtained TiO₂ nanosheets possess a unique crystalline core/amorphous shell structure (TiO₂@TiO_2?x), which exhibit the improved visible and near‐infrared light absorption. The types of dopants (oxygen vacancy/surface Ti³⁺/substituted N) in oxygen‐deficient TiO₂ can be tuned by controlling the working gases during plasma discharge. Both surface Ti³⁺ and substituted N were doped into the lattice of TiO₂ through NH₃ plasma discharge, whereas the oxygen vacancy or Ti³⁺ (along with the oxygen vacancy) was obtained after Ar or H₂ plasma treatment. The TiO₂@TiO_2?x from NH₃ plasma with a green color shows the highest photocatalytic activity under visible‐light irradiation compared with the products from Ar plasma or H₂ plasma due to the synergistic effect of reduction and simultaneous nitridation in the NH₃ plasma.     

Eliminated Phototoxicity of TiO2 Particles by an Atomic‐Layer‐Deposited Al2O3 Coating Layer for UV‐Protection Applications

We demonstrate the conformal coating of an ultrathin Al₂O₃ layer on TiO₂ nanoparticles through atomic layer deposition by using a specifically designed rotary reactor to eliminate the phototoxicity of the particles for cosmetic use. The ALD reactor is modified to improve the coating efficiency as well as the agitation of the particles for conformal coating. Elemental and microstructural analyses show that ultrathin Al₂O₃ layers are conformally deposited on the TiO₂ nanoparticles with a controlled thickness. Rhodamine B dye molecules on Al₂O₃‐coated TiO₂ exhibited a long life time under UV irradiation, that is, more than 2 h, compared to that on bare TiO₂, that is, 8 min, indicating mitigation of photocatalytic activity by the coated layer. The effect of carbon impurities in the film resulting from various deposition temperatures and thicknesses of the Al₂O₃ layer on the photocatalytic activity are also thoroughly investigated with controlled experimental condition by using dye molecules on the surface. Our results reveal that an increased carbon impurity resulting from a low processing temperature provides a charge conduction path and generates reactive oxygen species causing the degradation of dye molecule. A thin coated layer, that is, less than 3 nm, also induced the tunneling of electrons and holes to the surface, hence oxidizing dye molecules. Furthermore, the introduction of an Al₂O₃ layer on TiO₂ improves the light trapping thus, enhances the UV absorption.     

Controllable Growth of Perovskite Films by Room‐Temperature Air Exposure for Efficient Planar Heterojunction Photovoltaic Cells

A two‐step solution processing approach has been established to grow void‐free perovskite films for low‐cost high‐performance planar heterojunction photovoltaic devices. A high‐temperature thermal annealing treatment was applied to drive the diffusion of CH₃NH₃I precursor molecules into a compact PbI₂ layer to form perovskite films. However, thermal annealing for extended periods led to degraded device performance owing to the defects generated by decomposition of perovskite into PbI₂. A controllable layer‐by‐layer spin‐coating method was used to grow “bilayer” CH₃NH₃I/PbI₂ films, and then drive the interdiffusion between PbI₂ and CH₃NH₃I layers by a simple air exposure at room temperature for making well‐oriented, highly crystalline perovskite films without thermal annealing. This high degree of crystallinity resulted in a carrier diffusion length of ca. 800 nm and a high device efficiency of 15.6 %, which is comparable to values reported for thermally annealed perovskite films.     

Visible‐Light‐Induced Electron Transport from Small to Large Nanoparticles in Bimodal Gold Nanoparticle‐Loaded Titanium(IV) Oxide

A key to realizing the sustainable society is to develop highly active photocatalysts for selective organic synthesis effectively using sunlight as the energy source. Recently, metal‐oxide‐supported gold nanoparticles (NPs) have emerged as a new type of visible‐light photocatalysts driven by the excitation of localized surface plasmon resonance of Au NPs. Here we show that visible‐light irradiation (λ>430 nm) of TiO₂‐supported Au NPs with a bimodal size distribution (BM‐Au/TiO₂) gives rise to the long‐range (>40 nm) electron transport from about 14 small (ca. 2 nm) Au NPs to one large (ca. 9 nm) Au NP through the conduction band of TiO₂. As a result of the enhancement of charge separation, BM‐Au/TiO₂ exhibits a high level of visible‐light activity for the one‐step synthesis of azobenzenes from nitrobenzenes at 25 °C with a yield greater than 95 % and a selectivity greater than 99 %, whereas unimodal Au/TiO₂ (UM‐Au/TiO₂) is photocatalytically inactive.     

A Rutile TiO2 Electron Transport Layer for the Enhancement of Charge Collection for Efficient Perovskite Solar Cells

Interfacial charge collection efficiency has demonstrated significant effects on the power conversion efficiency (PCE) of perovskite solar cells (PSCs). Herein, crystalline phase‐dependent charge collection is investigated by using rutile and anatase TiO₂ electron transport layer (ETL) to fabricate PSCs. The results show that rutile TiO₂ ETL enhances the extraction and transportation of electrons to FTO and reduces the recombination, thanks to its better conductivity and improved interface with the CH₃NH₃PbI₃ (MAPbI₃) layer. Moreover, this may be also attributed to the fact that rutile TiO₂ has better match with perovskite grains, and less trap density. As a result, comparing with anatase TiO₂ ETL, MAPbI₃ PSCs with rutile TiO₂ ETL delivers significantly enhanced performance with a champion PCE of 20.9 % and a large open circuit voltage (V_OC) of 1.17 V.     

Photocatalytic Activity for Water Decomposition to Hydrogen over Nitrogen‐doped TiO2 Nanoparticle

Nitrogen-doped TiO2 nanoparticle photocatalysts were obtained by an annealing method with gaseous ammonia and nitrogen. The influence of dopant N on the crystal structure was characterized by XRD, XPS, BET, TEM and UV-Vis spectra. The results of XRD indicate that, the crystal phase transforms from anatase to rutile structure gradually with increase of annealing temperature from 300 to 700 ℃. XPS studies indicate that the nitrogen atom enters the TiO2 lattice and occupies the position of oxygen atom. Agglomeration of particles is found in TEM images after annealing. BET results show that the specific surface areas of N-doped samples from 44.61 to 38.27 m2/g are smaller than that of Degussa TiO2. UV-Vis spectra indicate that the absorption threshold shifts gradually with increase of annealing temperature, which shows absorption in the visible region. The influence of annealing condition on the photocatalytic property has been researched over water decomposition to hydrogen, indicating that nitrogen raises the photocatalytic activity for hydrogen evolution, and the modified TiO2 annealed for 2 h at 400 ℃ under gas of NH3/N2 (V/V＝1/2) mixture shows better efficiency of hydrogen evolution. Furthermore, the N-doped TiO2 nanoparticle catalysts have obvious visible light activity, evidenced by hydrogen evolution under visible light (λ＞400 nm) irradiation. However, the catalytic activity under visible light irradiation is absent for Degussa as reference and the N-doped TiO2 annealed at 700 ℃.     

Flexible NH3 sensors fabricated by in situ self-assembly of polypyrrole

Novel flexible NH₃ gas sensors were formed by the in situ self-assembly of polypyrrole (PPy) on plastic substrates. A negatively charged substrate was prepared by the formation of an organic monolayer (3-mercapto-1-propanesulfonic acid sodium salt—MPS) on a polyester (PET) substrate using a pair of comb-like Au electrodes. Two-cycle poly(4-styrenesulfonic acid) sodium salt/poly(allylamine hydrochloride) (PSS/PAH) bilayers (precursor layer) were then layer-by-layer (LBL) deposited on an MPS-modified substrate. Finally, a monolayer of PPy self-assembled in situ and PPy multilayer thin films self-assembled LBL in situ on a (PSS/PAH)₂/MPS/Au/Cr/PET substrate. The thin films were analyzed by atomic force microscopy (AFM). The effects of the precursor layer (PSS), the deposition time of the monolayer of PPy and the number of PPy multilayers on the gas sensing properties (response) and the flexibility of the sensors were investigated to optimize the fabrication of the film. Additionally, other sensing properties such as sensing linearity, reproducibility, response and recovery times, as well as cross-sensitivity effects were studied. The flexible NH₃ gas sensor exhibited a strong response that was comparable to or even greater than that of sensors that were fabricated on rigid substrate at room temperature.     

Sensitive Phenol Detection Using Tyrosinase‐Based Phenol Oxidation Combined with Redox Cycling of Catechol

This paper reports sensitive phenol detection using (i) tyrosinase (Tyr)‐based oxidation of phenol to catechol, combined with (ii) electrochemical‐chemical‐chemical (ECC) redox cycling involving Ru(NH₃)₆³⁺, catechol, and tris(2‐carboxyethyl)phosphine (TCEP). Phenol is converted into catechol by Tyr in the presence of dissolved O₂. Catechol then reacts with Ru(NH₃)₆³⁺, generating o‐benzoquinone and Ru(NH₃)₆²⁺. o‐Benzoquinone is reduced back to catechol by TCEP, and Ru(NH₃)₆²⁺ is accumulated over the course of the incubation. When Ru(NH₃)₆²⁺ is electrochemically oxidized to Ru(NH₃)₆³⁺, ECC redox cycling occurs. For simple phenol detection, bare ITO electrodes are used without modifying the electrodes with Tyr. The detection limit for phenol in tap water using Tyr‐based oxidation combined with ECC redox cycling is ca. 10^?9 M, while that using only Tyr‐based oxidation is ca. 10^?7 M.     

A Simple Method for the Preparation of TiO2/Ag‐AgCl@Polypyrrole Composite and Its Enhanced Visible‐Light Photocatalytic Activity

A novel and facile method was developed to prepare a visible‐light driven TiO₂/Ag‐AgCl@polypyrrole (PPy) photocatalyst with Ag‐AgCl nanoparticles supported on TiO₂ nanofibers and covered by a thin PPy shell. During the synthesis, the PPy shell and Ag‐AgCl nanoparticles were prepared simultaneously onto TiO₂ nanofibers, which simplified the preparation procedure. In addition, because Ag‐AgCl aggregates were fabricated via partly etching the Ag nanoparticles, their size was well controlled at the nanoscale, which was beneficial for improvement of the contact surface area. Compared with reference photocatalysts, the TiO₂/Ag‐AgCl@PPy composite exhibited an enhanced photodegradation activity towards rhodamine B under visible‐light irradiation. The superior photocatalytic property originated from synergistic effects between TiO₂ nanofibers, Ag‐AgCl nanoparticles and the PPy shell. Furthermore, the TiO₂/Ag‐AgCl@PPy composite could be easily separated and recycled without obvious reduction in activity.     

Diamondoid Nanostructures as sp3‐Carbon‐Based Gas Sensors

Diamondoids, sp³‐hybridized nanometer‐sized diamond‐like hydrocarbons (nanodiamonds), difunctionalized with hydroxy and primary phosphine oxide groups, enable the assembly of the first sp³‐C‐based chemical sensors by vapor deposition. Both pristine nanodiamonds and palladium nanolayered composites can be used to detect toxic NO₂ and NH₃ gases. This carbon‐based gas sensor technology allows reversible NO₂ detection down to 50 ppb and NH₃ detection at 25–100 ppm concentration with fast response and recovery processes at 100 °C. Reversible gas adsorption and detection is compatible with 50 % humidity conditions. Semiconducting p‐type sensing properties are achieved from devices based on primary phosphine–diamantanol, in which high specific area (ca. 140 m² g^?1) and channel nanoporosity derive from H‐bonding.     

Determination of ZnO(0001) surface termination by x‐ray photoelectron spectroscopy at photoemission angles of 0° and 70°

We present an XPS method to determine the termination of the ZnO(0001) surface. By measuring O 1s and Zn 2p_3/2 core‐level x‐ray photoelectron spectra at photoemission angles of 0° and 70° and comparing the intensity ratio (I_O1s/I_Zn2p3)_θ=0/(I_O1s/I_Zn2p3)_θ=70, the Zn and O termination can be distinguished. Calculations show that these two terminations have intensity ratios differing by ～17%. This difference is not affected by a contamination layer provided that the contamination layer thickness is the same for these two differently terminated surfaces. Although this determination method prefers a clean ZnO(0001) surface (in situ measurement), it seems also feasible for surfaces with known contamination layer thickness (ex situ measurement). We have measured ex situ ZnO(0001)‐Zn, ZnO(000&1macr;)‐O single crystals and an epitaxial ZnO film deposited on Al₂O₃(0001). The measured intensity ratios of the first two samples agree with the calculated values for a 0.2 and 0.26 nm contamination layer, respectively. The intensity ratio and the O 1s contamination component intensity of the epitaxial ZnO film are close to those of the ZnO(0001)‐Zn single crystal thus pointing at Zn termination of the film. Copyright © 2004 John Wiley & Sons, Ltd.     

TiO2/Cu2O Core/Ultrathin Shell Nanorods as Efficient and Stable Photocatalysts for Water Reduction

P‐type Cu₂O has been long considered as an attractive photocatalyst for photocatalytic water reduction, but few successful examples has been reported. Here, we report the synthesis of TiO₂ (core)/Cu₂O (ultrathin film shell) nanorods by a redox reaction between Cu²⁺ and in‐situ generated Ti³⁺ when Cu²⁺‐exchanged H‐titanate nanotubes are calcined in air. Owing to the strong TiO₂‐Cu₂O interfacial interaction, TiO₂ (core)/Cu₂O (ultrathin film shell) nanorods are highly active and stable in photocatalytic water reduction. The TiO₂ core and Cu₂O ultrathin film shell respectively act as the photosensitizer and cocatalyst, and both the photoexcited electrons in the conduction band and the holes in the valence band of TiO₂ respectively transfer to the conduction band and valence band of the Cu₂O ultrathin film shell. Our results unambiguously show that Cu₂O itself can act as the highly active and stable cocatalyst for photocatalytic water reduction.     

Ultrathin polymer gate buffer layer for air‐stable,low‐voltage,n‐channel organic thin‐film transistors

An ultrathin poly(methyl methacrylate) (PMMA) buffer layer was developed to improve the performance of n‐channel organic thin‐film transistors (OTFTs). The 8 nm‐thick PMMA film, prepared by spin‐coating, provided a very smooth surface and a uniform coverage on SiO₂ surface reproducibly, which was confirmed by X‐ray reflectivity (XR) measurement. Then, we fabricated N,N′‐ditridecyl‐3,4,9,10‐perylenetetracarboxylic diimide (PTCDI‐C13) thin‐film transistors with and without this 8 nm‐thick PMMA insulating layer on SiO₂ gate insulators and achieved one‐order increase of field‐effect mobility (up to 0.11 cm²/(Vs) in a vacuum), one‐half decrease of threshold voltage, and reduction of current hysteresis with the PMMA layer. Only TFTs with the PMMA layer displayed n‐channel operation in air and showed field‐effect mobility of 0.10 cm²/(Vs). We consider that electrical characteristics of n‐channel OTFTs were considerably improved because the ultrathin PMMA film could effectively passivate the SiO₂ insulator surface and decrease interfacial electron traps. This result suggests the importance of the ultrathin PMMA layer for controlling the interfacial state at the semiconductor/insulator interface and the device characteristics of OTFTs. Copyright © 2009 John Wiley & Sons, Ltd.     

Electrospun nanofibers of ZnO‐TiO2 hybrid: characterization and potential as an extracellular scaffold for supporting myoblasts

One‐dimensional nanofibers have attracted tremendous attention because of their potential applications. Electrospinning technology enables industrial production of these nanofibers. This study aims to fabricate one‐dimensional ZnO doped TiO₂ by electrospinning and to characterize these hybrid nanofibers. The nanocomposite was prepared using colloidal gel composed of zinc nitrate, titanium isopropoxide and polyvinyl acetate. X‐ray diffraction, energy dispersive x‐ray analysis and transmission electron microscopy analysis confirmed the purity and crystalline nature of this material, whereas the diameter of these nanofibres estimated from scanning electron microscope (SEM), field emission SEM and transmission electron microscopy are between 200 and 300 nm. Cell counting with Kit‐8 assay at regular time intervals and phase‐contrast microscopy data revealed that C2C12 cells proliferated well on ZnO/TiO₂ nanofibers between 1 and 10 µg/ml, and cellular attachments are visible by SEM. The nanostructured ZnO/TiO₂ hybrid nanofibers show higher cell adhesion, proliferation and spreading behavior compared with the titanium substrate and control. Our study suggests that ZnO/TiO₂ nanofibers could potentially be used in tissue engineering applications. The scalability, low cost, reproducibility and high‐throughput capability of this technology is potentially beneficial to examine and optimizing a wide array of cell‐nanofiber systems prior to in vivo experiments. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and Characterization of TiO2 Doped ZnO Microtubes

The TiO₂-doped ZnO microtubes have been successfully fabricated via a wet chemicalmethod, using zinc chloride and titanium sulphate as the starting materials. The as-synthesized products were characterized by X-ray diffraction, field emission scanning electronmicroscopy and room temperature photoluminescence measurement. The photocatalytic ac-tivity in degrading methyl orange was measured with a UV-Vis spectrophotometer. The pure ZnO microtubes exhibit an exact hexangular hollow structure with a diameter of about 700 nm, a length of 3 μm and a wall thickness of about 40 nm. The TiO₂-doped ZnO microtubes with TiO₂/ZnO ratio less than 5% have the same dimension with the pure ZnO microtubes, a smooth column shape, not a hexangular structure. The growth of ZnO may be inhibited by the more Ti⁴⁺ doped into ZnO structure to achieve a small dimension or a multiphase. The crystallinity of ZnO microtubes decreases with increasing TiO₂ content, and then a multiphase containing ZnO, Ti₃O₅ and TiO occur when the TiO₂/ZnO ratio is more than 5%. The UV emission intensity of the TiO₂-doped ZnO obviously increases and then tends to decrease with TiO₂/ZnO ratio increasing. The photocatalytic properties of the TiO₂-doped ZnO microtubes are very effcient in degrading organic dyes of methyl orange and are well identical with its PL properties and the crystallinity.     

Enhancing Electron Collection Efficiency and Effective Diffusion Length in Dye‐Sensitized Solar Cells

Intensity‐modulated photocurrent spectroscopy and intensity‐modulated photovoltage spectroscopy are employed to measure the dynamics of electron transport and recombination in the ZnO nanowire (NW) array‐ZnO/layered basic zinc acetate (LBZA) nanoparticle (NP) composite dye‐sensitized solar cells (DSSCs). The roles of the vertical ZnO NWs and insulating LBZA in the electron collection and transport in DSSCs are investigated by comparing the results to those in the TiO₂–NP, horizontal TiO₂–NW and vertical ZnO–NW‐array DSSCs. The electron transport rate and electron lifetime in the ZnO NW/NP composite DSSC are superior to those in the conventional TiO₂–NP cell due to the existence of the vertical ZnO NWs and insulating LBZA. It indicates that the ZnO NW/NP composite anode is able to sustain efficient electron collection over much greater thickness than the TiO₂–NP cell does. Consequently, a larger effective electron diffusion length is available in the ZnO composite DSSC.