土壤样品中砷的形态分析方法研究

对生态地球化学土壤样品,在Tessier修正顺序提取方法(即七步法)的基础上对提取方法、提取时间、提取溶液的处理方法进行优化选择,用超声法提取水溶态、离子交换态、碳酸盐结合态、腐殖酸结合态、铁锰氧化物结合态、强有机质结合态和残渣态七种形态的砷元素,用原子荧光光谱法测定各个形态砷的含量。优化后的方法测得As元素各形态的检出限均小于1.0μg/g,相对标准偏差(RSD)小于10%,准确度高,质量参数均满足生态地球化学土壤样品评价形态分析的需要。     

成都经济生态区大气降尘中镉赋存形态的研究

采用Tessier连续提取法对成都经济生态区不同区域的24个大气降尘样中镉的赋存形态进行了研究。研究结果表明,大气降尘中的镉主要以残留态形态存在;各形态镉在总镉中所占百分比含量由大到小排列顺序依次是:残留态,碳酸盐结合态,交换态,铁锰结合态,有机结合态;交换态镉、碳酸盐结合态镉这两种具有较高生物有效性的形态镉在总镉中所占的平均百分比含量分别是6.420%和8.917%;铁锰氧化物结合态、有机结合态、残留态镉这三种形态镉生物有效性很低,分别在总镉中所占的平均百分比含量分别是3.419%、2.365%和78.907%。通过分析可得出,汽油和煤的燃烧以及工厂排放镉能加大城市大气降尘的镉污染。     

硼镁合金粉中硼的测定

报道了酸碱滴定法测定硼镁合金中的硼。确定了试样的溶解方法,建立了合理的分析步骤。对3个试样进行分析测定。其方法的回收率为98%～103%,RSD为10%。     

ICP-AES法同时测定土壤中有效态的硫和硼

采用一种方法同时提取国标土壤样品中的有效态硫和硼元素,再使用ICP-AES法进行测定。其测定值与标准值相比,硫和硼的相对误差分别小于1.4%和13%,均在允许误差范围内;方法的相对标准偏差,硫为3.2%~3.4%,硼为6.3%~7.6%;磷酸钙溶液作为提出剂条件下,方法的检出限硫为0.114μg/mL,硼为0.0039μg/mL,氯化钙溶液作为提出剂条件下,硫为0.151μg/mL,硼为0.0035μg/mL。     

酸碱滴定法测定硼粉中硼

以酸碱滴定法测定硼粉中硼含量。称样质量为0.14～0.20 g,加酸加热回流50 min,定容至500 mL,移取50.00 mL作为样品溶液。样品溶液先用碱液中和至pH 5.4,然后加入5 g甘露醇,用0.1 mol/L氢氧化钠标准滴定溶液滴定,临近终点时记录消耗的体积与试液pH值,用二级微商法算得终点体积。硼含量测定结果的相对标准偏差为0.32%～0.42%(n=9)。对比测定硼酸硼含量,该方法所得结果的相对标准偏差为0.05%(n=5)。     

波密闭增压浸提柑桔园土壤中水溶态硼

提出了在微波炉加热用水提取土壤中水溶态硼的处理方法,采用的辐射功率为1.36 kW,加热提取过程分先后两步:①在0.1 MPa压力下加热90s,②在0.2 MPa压力下加热125 s.从某柑桔园中采得土壤样品12个,分别按回流浸提法和微波消解法提取其水溶态硼并用石墨炉原子吸收光谱法(GF-AAS)测定其含量,两种提取方法所测结果的一元回归方程的相关系数为0.991,对该回归方程斜率和截距进行t检验,表明两种方法所得的水溶态硼量之问无显著差异(置信水平95%).取同一试样5份,分别按所述方法提取其水溶态硼并按GF-AAS法测定,计算分析结果的相对标准偏差(n=5)为3.4%(微波消解法)和5.7%(回流浸提法).     

延安市污水处理厂污泥中6种重金属元素的形态分析

采用Tessier连续提取法对延安市污水处理厂污泥中的Zn、Cu、Cr、Cd、Pb和Mn六种重金属元素进行形态提取,并用电感耦合等离子体发射光谱(ICP-AES)法对其中各元素的总量及其形态进行测定。结果表明： Pb、Cd多以可交换态、碳酸盐结合态存在,分别占总量的76.84%和78.59%, 对生物具有潜在有效性。Zn、Cu、Cr多以稳定的硫化物及有机结合态和残渣态存在,不易迁移到环境中去。     

连续萃取法研究海湾养殖区沉积物中重金属形态

以连续萃取法研究海湾养殖区沉积物中重金属(Cd, Cu, Pb, Zn)的形态,将重金属分离为酸溶态、还原态、有机质结合态、硫化物结合态和残渣态.分别采用基体匹配法和内标法消除高盐基体对电感耦合等离子体光谱法(ICP-OES)和质谱法(ICP-MS)分析结果的影响.对海洋沉积物标准物质分析结果表明,样品稀释后测定值与标准值一致.比较了本连续萃取法和BCR法对沉积物样品中重金属形态的提取结果,并考察了萃取剂的选择性.实验表明,本方法可用于有机质污染和富营养化环境沉积物中重金属形态分析,特别是有机质结合态和硫化物结合态的分析.     

稀土矿开采过程中重金属铅活化过程分析

采用Tessier连续提取法确定矿样中Pb的存在形态和组成。通过土柱实验对稀土矿的开采过程进行模拟,研究稀土矿开采过程中NH_4~+活化重金属Pb的过程。结果表明:Fe-Mn氧化物结合态和可交换态是矿样中Pb最主要的存在形态,约占Pb总量68.75%和23.13%。土柱实验中可交换态的Pb减少0.7358 mg,占浸矿前含量的84.98%。浸出液中的Pb占浸矿前可交换态Pb的5.67%。土柱中碳酸盐结合态Pb和Fe-Mn氧化物结合态Pb含量增加,分别增加0.3224和0.091 mg,占未浸矿前可交换态Pb的37.24%和10.5%。因此,离子型稀土矿开采过程中优先活化可交换态Pb,被活化的可交换态Pb一部分随稀土母液流出矿体,另一部分在形态上转化为其他态。     

电感耦合等离子体质谱法测定硼同位素丰度

以硼同位素标准物质NIST SRM 951配制标准溶液,在优化的仪器操作条件下对电感耦合等离子体质谱(ICP-MS)测定的硼同位素质量进行校正,求出校正因子,确定了样品的线性浓度范围,选定样品浓度为1.1 mg/L。在同样的仪器条件下首先测定了硼标准物质的硼同位素丰度比,测量误差为0.2%,然后测定了硼同位素浓缩过程中硼样品的硼同位素丰度比,测定结果的相对标准偏差为1.1%。此外考察了仪器的稳定性。实验结果表明本方法“记忆效应”小,结果可靠,测量精度高。     

Boron Separation by the Two—step Ion—Exchange for the Isotopic Measurement of Boron

ＩｎｔｒｏｄｕｃｔｉｏｎＬａｒｇｅｖａｒｉａｔｉｏｎｓｉｎｔｈｅｉｓｏｔｏｐｉｃｃｏｍｐｏｓｉｔｉｏｎｏｆｂｏｒｏｎｏｃｃｕｒｉｎｎａｔｕｒｅ .ＴｈｅｂｏｒｏｎｉｓａｕｓｅｆｕｌｔｒａｃｅｒｏｆｔｈｅｓｏｕｒｃｅｓａｎｄｅｖｏｌｕｔｉｏｎｏｆａｑｕｅｏｕｓｆｌｕｉｄｓｉｎｔｈｅＥａｒｔｈ’ｓｃｒｕｓｔａｎｄｈｙｄｒｏｓｐｈｅｒｅ .1 6Ｏｗｉｎｇｔｏｉｍｐｒｏｖｅｍｅｎｔｓｏｆａｎａ ｌｙｔｉｃａｌｍｅｔｈｏｄｓ ,7,8ａｒａｐｉｄｉｎｃｒｅａｓｅｈａｓｂｅｅｎｓｅｅｎｉｎｍａｎｙｓｔｕｄｉｅｓｏｆｔ…     

Polymer-Supported Boron Trifluoride

Polystyrene, cross-linked with 7.8% of divinylbenzene, formed a stable complex in chloroform with boron trifluoride containing 0.11% of boron, while cross-linked polystyrene-4-vinylpyridine resins containing 2–2.5% of pyridine rings formed a stable complex with boron trifluoride, containing 1.04% of boron. Both complexes catalyze conversions of aromatic aldehydes, ketones, and acids with alcohols into corresponding acetals, cyclic ketals, and esters; diphenylmethanol converts into ether. The structure of the alcohol plays an important role, with conversions decreasing in the order 1-butanol, 2-butanol, tert-butanol. Both complexes are very stable and in most cases more reactive than the cross-linked polystyrene-A1C1₃ complex.     

杨梅缺硼症状与硼肥施用技术研究

为矫治杨梅缺硼症状，采用了喷施和土施硼肥技术。调查和试验结果表明，杨梅硼元素缺乏的典型生理症状为叶小、枝梢丛生、枯梢、花量少，且不结果或很少结果。喷施0，2％硼砂液或0．2％硼砂 0．5％尿素液能明显矫治杨梅缺硼症状，改善春、夏两梢生长指标，提高坐果率，从而提高单株产量。土施硼肥也能取得较好的矫治效果，施用量以硼砂100g／株为佳；同时，土施处理在生产实际中还表现出良好的后续效应。     

锆硼陶瓷材料中总硼分析方法研究

对锆硼陶瓷材料中总硼的分析方法进行了研究，采用硫酸和硫酸铵及重铬酸钾氧化两步溶解法分解样品，氮气载带硼酸三甲酯蒸馏分离硼与锆（氦气流速150mL/min水溶加热，NaOH溶液吸收），材料中成分为Zr粉＋B4C粉，Zr含量≥99％（ut），经阳离子交换法除去吸收液中Na后采用ICP-AES法测定硼。方法的相对标准偏差（n=6）小于2．0％；标准加入回收率为99％。     

The Boron and Lithium Content of South African Coals and Coal Ashes

Abstract

Boron and lithium were determined in over a hundred coals and power station ashes by inductively coupled plasma atomic emission spectroscopy. The levels of boron in coals and fly ashes range from 15 to 83 μg.g^?1 and from 23 to 600 μg.g^?1, respectively, while lithium occurred at levels of between 45 and 81μg.g^?1 in coals and 77 and 359μg.g^?1 in fly ashes. Both elements were found to vary considerably between different coals and ashes produced. In most cases the boron concentration was found to increase systematically between the first and last precipitators where smaller particle size fractions are collected. The availability of boron from the leaching of fly ashes by water was investigated. Leachabilities were found to vary for ashes produced at different power stations.     

Boron adsorption mechanism on polyvinyl alcohol

Recently, an increase in the use of boron compounds has led to an increase in boron emissions, and concern has grown regarding its detrimental effects on the human body. An adsorbent that adsorbs boron selectively has been developed as a countermeasure. Although certain commercially available boron selective adsorbents can be used to remove boron from aqueous solutions by utilizing the strong affinity between boron and hydroxyl groups, the adsorption capacity appears to be insufficient. So, we adopted polyvinyl alcohol (PVA), which contains many hydroxyl groups, as a model adsorbent. We investigated the boron adsorption characteristics of PVA, and then studied the relationship between the number of adsorption sites and actual adsorption amounts. We assessed the adsorption result by using adsorption site availability (ASA) as an indicator of the ratio of effectively functioning hydroxyl groups from the many hydroxyl groups in PVA. ASA was expressed as a percentage of the experimental equilibrium adsorbed amount in relation to the theoretical equilibrium adsorbed amount. We also compared the adsorption isotherms and ASA obtained with PVA, commercially available N-methylglucamine-type resin (CRB03 and CRB05) and the adsorbent we synthesized from polyallylamine (PAA) and glucose (PAA-Glu). Although PVA has many hydroxyl groups in a molecule, ASA analysis revealed that only 6% of the hydroxyl groups in PVA was used for boron adsorption. On the other hand, CRBs and PAA-Glu exhibited higher ASA values (about 15% and 35% respectively) and adsorption amounts, suggesting that the sterically congested adsorbent structure had a great influence on boron adsorption and ASA.     

石墨炉原子吸收光谱测硼时基体改进剂的选择

研究各种基体改进剂的增感效果,和它们对灰化、原子化温度的影响。结果表明,Ca、Sr、Ca-Mg、Ca-La、Sr-Mg均可作为硼的基体改进剂,且Ca-Mg、Ca-La、Sr-Mg较之Ca、Sr性能优越。并分别以Ca、Ca-Mg、Sr-Mg作基体改进剂,直接分析饮用水中痕量硼,所得结果基本一致,相对标准偏差均在10%以内。     

Effect of Method of Boron Introduction into NiMo/Al2O3 Protective-Layer Catalysts on the Removal of Silicon from Diesel Fractions

Russian Journal of Applied Chemistry - NiMo/γ-Al2O3 protective-layer catalysts for removing silicon from diesel fractions were examined. The catalysts differ in the way in which boron is...     

用于高性能锂-硫电池的氮化硼纳米片/碳纤维改性隔膜

通过静电纺丝、热亚胺化和碳化过程,将氮化硼纳米片(BNNSs)负载在碳纤维(CFs)表面,组成用于修饰商业聚丙烯(PP)隔膜的氮化硼纳米片/碳复合纤维(BNNSs/CFs)复合材料。BNNSs和CFs的协同作用为电池提供了额外的导电路径,并将可溶性多硫化锂固定在正极区域。结果表明,采用10BNNSs/CFs-PP隔膜的电池在0.05C下的初始放电容量高达1 295.7 mAh·g^-1,当电流密度增加到1C时,以10BNNSs/CFs-PP为隔膜的电池也具有良好的长期循环稳定性,在400次循环后最终容量高达583.1mAh·g^-1,每次循环容量衰减0.069%。