多次聚合法制备多孔聚吡咯厚膜及其电化学容量性能

为了得到高面积比容量的聚吡咯(PPy)膜超级电容器电极材料, 用多次聚合法合成了PPy厚膜, 聚合电量分别为8、10和12 mAh·cm-2, 掺杂离子分别为氯离子和对甲基苯磺酸根离子(TOS-). PPy膜的电化学性能采用恒电流充放电、循环伏安(CV)和电化学阻抗谱(EIS)等方法测试. 研究表明, 多次聚合法可以制备表面平整且内部均匀多孔的PPy厚膜. 在聚合电量为12 mAh·cm-2时, 用Cl-、TOS-两种离子掺杂的PPy厚膜的面积比容量高达5 F·cm-2, 并表现出理想的电化学容量性能. 同时PPy-Cl厚膜的质量比容量达到330 F·g-1, PPy-TOS厚膜的质量比容量略低(191 F·g-1), 但具有更快的充放电速率. 与一次聚合法合成的PPy 薄膜相比, 多次聚合法合成的PPy厚膜的质量比容量没有降低. 通过场发射扫描电镜(SEM)观察了一次聚合法和多次聚合法制备的PPy厚膜的截面形貌, 并讨论了多次聚合法的合成机理.     

不同电解质溶液对聚吡咯修饰膜性质的影响

以对甲基苯磺酸钠(p-TSNa)为掺杂剂在不锈钢电极表面恒电位合成聚吡咯(PPy)修饰膜, 采用循环伏安法在-1.6 - 0.8 V大范围扫描研究了修饰膜在H2SO4、Na2SO4、NaOH电解质溶液中的氧化还原行为. 结果表明, 在H2SO4溶液中, 以H+的脱出(氧化)/嵌入(还原)为特征, 并发现聚吡咯在酸性溶液中所特有的质子还原峰. 在Na2SO4和NaOH溶液中, 以Na+的脱出(氧化)/嵌入(还原)峰为特征. FT-IR吸收光谱显示, 经NaOH处理后, 聚吡咯膜的长共轭结构被完全破坏, 而经H2SO4和Na2SO4处后, 膜的共轭结构未发生变化.     

聚吡咯/聚苯胺复合型导电聚合物防腐蚀性能

采用循环伏安法,在含吡咯和苯胺的0.3 mol/L草酸水溶液中制备了聚吡咯/聚苯胺(PPy/Pani)的复合型导电聚合膜。采用红外光谱、极化曲线、自腐蚀电位-时间曲线、扫描电子显微镜和电化学阻抗谱研究了共聚膜的防腐蚀性能。结果表明,在1 mol/L H2SO4中,PPy、Pani与不锈钢基体发生氧化还原反应,促进不锈钢表面发生钝化;当苯胺与吡咯浓度比为1∶3时,制备得到的复合型导电聚合膜所保护的不锈钢自腐蚀电流最小,自腐蚀电位最高,保护时间最长。PPy、Pani及其共聚膜在3.5%NaCl溶液中电化学阻抗谱表明,所制备的PPy、Pani及其共聚物膜与不锈钢基体发生氧化还原反应,使其表面钝化;当Cl-到达不锈钢表面时,破坏钝化膜导致不锈钢腐蚀。     

聚合溶液pH值对染料敏化太阳电池中聚吡咯对电极结构和性能的影响

电化学合成聚吡咯(PPy)时,聚合电解液的pH值对PPy薄膜的形貌和性质有较大的影响,进而影响PPy薄膜对I-/I3-的电催化活性以及基于PPy对电极(CE)的染料敏化太阳电池(DSSCs)的光电转换性能.本文采用电化学恒电位方法,在掺杂氟的SnO2(FTO)导电玻璃上合成出了对甲苯磺酸根离子掺杂的聚吡咯(PPyTsO)电极,并将其作为DSSCs的对电极.通过改变吡咯聚合时聚合电解液的pH值,借助扫描电镜(SEM)、紫外-可见(UV-Vis)吸收光谱、X-射线光电子能谱(XPS)和循环伏安(CV)等表征技术,详细探讨了聚合溶液pH值对PPy CE形貌、结构及其对I-/I3-的电催化性能的影响.研究发现在pH 2.0下合成的聚吡咯对阴离子掺杂率最高且链共轭性最佳,具有对I-/I3-氧化还原介质最强的催化能力,基于此PPy CE的电池光电转化效率也最高.pH值太大或太小都不利于生成具有高掺杂率和高催化活性的PPy电极,组装成DSSCs后的光电转换效率也较低.     

AZ31镁合金表面聚吡咯的化学氧化合成及其耐蚀性能

以对甲苯磺酸钠为掺杂剂, 三氯化铁为氧化剂, 用化学氧化聚合法在AZ31 镁合金表面制备聚吡咯(PPy)膜. 采用傅里叶变换红外(FTIR)光谱分析了镁合金表面聚吡咯膜结构, 通过电化学极化曲线、电化学阻抗谱(EIS)研究了其耐蚀性能, 通过扫描电子显微镜(SEM)、X射线能量散射谱(EDS)分析了表面形貌和成分. 和镁合金裸样相比, 聚吡咯膜对镁合金腐蚀有一定的抑制作用. 硅烷预处理改善了镁合金/聚吡咯体系的耐腐蚀性能, 使腐蚀电位较镁合金裸样正移了110 mV, 电流密度减小了约2个数量级.     

天然海水中聚吡咯膜的防微生物附着及防腐蚀性能

采用恒电流法在316 L不锈钢电极表面合成聚吡咯(PPy), 通过开路电位、 生物显微镜(BM)、 Tafel极化曲线及电化学交流阻抗(EIS)研究了聚吡咯防止微生物附着及防腐蚀特性. 研究表明, 沉积聚吡咯的316 L不锈钢电极浸泡在天然海水中(0~20 d), 开路电位基本保持不变, 表明电化学合成的聚吡咯膜有良好的防止微生物附着能力, 并通过生物显微镜进行了验证, 且在浸泡的过程中其腐蚀电流密度维持在10^-7 mA/cm², 表现出良好的防腐蚀特性; 浸泡50 d后, 其防腐蚀效率仍高达97.45%. 因此, 电化学合成的聚吡咯具有优异的防止微生物附着和防腐蚀特性.     

生物功能电极 III. 葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合, 将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响, 并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现, 由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性, 酶反应表观上遵循Michealis-Menten动力学。     

生物功能电极 Ⅲ.葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合,将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响,并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现,由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性,酶反应表观上遵循Michealis-Menten动力学。     

聚吡咯对Cu(II)的催化还原作用

以对甲苯磺酸钠为掺杂剂在不锈钢(SS)电极表面恒电位合成聚吡咯(PPy)修饰膜, 采用恒电位和动电位对Cu(II)的还原效果进行了研究, 并与不锈钢电极进行了对比. 结果表明, 由于聚吡咯的催化作用, 聚吡咯修饰电极对Cu(II)还原效率高于不锈钢电极; 聚吡咯膜对析氢有明显的抑制作用, 因此电流效率远远高于不锈钢电极, 这是采用聚吡咯进行电化学还原的明显优势. 通过在不同浓度Cu(II)酸性溶液中的循环伏安行为讨论了聚吡咯对Cu(II)的还原作用机理.     

掺杂离子对聚吡咯膜的电化学容量性能的影响

用电化学方法制备了分别以对甲基苯磺酸根(TOS-), 高氯酸根(ClO-4)和氯离子(Cl-)掺杂的聚吡咯(PPy)膜. 用循环伏安(CV)、恒电流充放电和电化学阻抗谱(EIS)等测试了它们的电化学容量性能. 用扫描电镜(SEM)和X射线衍射(XRD)分别研究了这三种PPy膜的形貌和结构. 研究发现, 由于具有疏松多孔的形貌和更有序的分子链结构, PPy-TOS和 PPy-Cl膜具有较好的充放电能力, 在深度充放电时仍具有很小的电化学电阻, 其离子扩散接近理想电容器的离子扩散机理. PPy-Cl(聚合电量2 mAh·cm-2)的比容量在扫描速率为5 mV·s-1时高达270 F·g-1, 扫描速率200 mV·s-1时仍高达175 F·g-1, 特别是, 其比能量高达35.3 mWh·g-1. PPy-TOS由于有质量较大的掺杂离子(TOS-)因而比容量略低(146 F·g-1, 扫描速率5 mV·s-1), 但具有超快速充放电能力, 在扫描速率为200 mV·s-1时, 比容量为123.6 F·g-1, 其比功率高达10 W·g-1. 并且, 两种电极材料均具有稳定的电化学循环性能.     

Microelectrode Combinations of Gold and Polypyrrole Enable Highly Stable Two-electrode Electrochemical Impedance Spectroscopy Measurements under Turbulent Flow Conditions

An electrochemical impedance spectroscopy (EIS) sensor design is proposed based on a standard interdigitated electrode layout in which the smaller working electrode consists of gold (Au) whereas the larger combined counter and reference electrode is coated with a porous layer of polypyrrole (PPy) doped with polystyrene sulfonate (PSS) (PPy : PSS). Each electrode material was first characterized by EIS in a standard 3-electrode setup with subsequent spectra fitting by a modified Randles equivalent circuit. The differences in the spectra obtained by the PPy : PSS coated electrodes can be explained by an increased electroactive surface area due to the porous polymer film. The changes in morphology of the film are discussed with respect to the evolution of the elements of the electric equivalent circuit. When applying the Au/PPy : PSS electrode combination to a standard 2-electrode arrangement, the enlarged highly electroactive surface area of the PPy : PSS coating lowers the interfacial impedance in a way that mainly the gold working electrode contributes to the overall system impedance. Therefore, obtaining reproducible EIS signals depends only on the electrode's open-circuit potential (OCP) and on additional adsorption events at the gold electrode/electrolyte interface. We present a protocol for microelectrode coating with PPy : PSS, which enables highly stable 2-electrode EIS experiments without the need of a reference electrode. This combination is believed to be very useful if an integration of sensing electrodes inside Micro Total Analysis Systems is aspired.     

Hollow microstructures of polypyrrole doped by poly(styrene sulfonic acid)

Microstructures with hollow interiors, such as microspheres, microcrocks, microbowls, and micropumpkins, were prepared through the direct electrochemical oxidation of pyrrole in an aqueous solution of poly(styrene sulfonic acid) (PSSA). Scanning electron microscopy demonstrated that the microstructures possessed hollow interiors. The addition of polymeric doping ions made the skins of the microstructures very smooth, and several novel structures were observed. The morphology of the microstructures was simply modulated through changes in the electrochemical conditions. Raman and Fourier transform infrared characterizations indicated that the microstructures were made of conductive polypyrrole (PPy) doped by polymeric anions of poly(styrene sulfonate), and X‐ray diffraction showed that the microstructures were amorphous. Thermogravimetric analysis indicated that PPy–PSSA composite films with microstructures had higher thermal stability than pure PPy, PPy‐coated PSSA microspheres, and naphthalene sulfonic acid doped PPy microstructures. Furthermore, PPy–PSSA composite films with microstructures showed cation‐exchange behavior during the redox process in aqueous solutions of sodium dodecyl benzenesulfonate. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3170–3177, 2004     

Perchlorate interchange during the redox process of PPy/PVS films in an acetonitrile medium. a voltammetric and EDX study

Polypyrrole/poly(vinyl sulfonate) (PPy/PVS) films in acetonitrile containing 0.1 M LiClO4 were studied by cyclic voltammetry. Consecutive voltammograms pointed to a continuous increase in the charge involved in the process, suggesting a rise in the number of the electroactive participants involved in the redox process. However, voltammograms obtained for the PPy/ClO4 films in analogous conditions pointed to a steady-state behavior from the very early cycles. Theoretical studies based on the Nernst and Butler-Volmer equations indicated that perchlorate ions are involved during the oxidation/reduction process of the PPy/PVS films when the steady state is reached. This result was confirmed by "ex situ" energy-dispersive X-ray analysis of the films. In this regard, the electrochemical behavior of PPy/PVS polymers was similar to that of PPy/ClO4 films when a high number of cycles were carried out. The exchange of ClO4- during the redox reaction of the PPy/PVS films made it necessary to incorporate Li+ cations inside the polymer during the initial voltammetric cycles to compensate for the negative charges of PVS polyanions. Li+ cations are mainly stabilized inside the polymer by the ion pairs formed with the sulfonated groups of the PVS. An increase and shift of the voltammetric cycles indicated a restructuring of the polymeric chains with consecutive scans.     

聚吡咯/碳纳米管分子印迹修饰电极对槲皮素的选择性测定

制备了一种新颖的可对槲皮素分子进行选择性测定的分子印迹聚合物膜修饰电极.在碳纳米管(CNT)独特的结构和力学性能作用下,以吡咯(Py)为功能单体,槲皮素为模板分子,电聚合方法制备了槲皮素的分子印迹聚合物膜修饰电极(PPy/CNT/GCEMIP).用电化学交流阻抗法研究了该修饰电极的界面性质,用循环伏安法和差分脉冲伏安法...     

A comparison of redox processes for polypyrrole/dodecylsulfate films in aqueous and non-aqueous media

Polypyrrole/dodecylsulfate (PPy/DDS) films were synthesized in aqueous and ethanolic solutions and investigated in aqueous, ethanolic, methanolic and acetonitrile solutions by cyclic voltammetry (CV). The amounts of anions and cations in the films before and after electrochemical treatment were determined by electron probe microanalysis (EPMA); the film morphology was studied by scanning electron microscopy (SEM). The results prove that the mobility of bulky DDS^– ions in PPy increases in the order: water<acetonitrile<ethanol<methanol. It was found that dopant DDS^– ions can be easily removed from PPy matrix swollen in alcohols or acetonitrile by electrochemical reduction or by soaking in electrolyte solutions of these solvents. The influence of electrochemical treatment on the change of doping level in aqueous solution is essentially less and depends on the cations in the test solution. Although the electroneutrality of PPy/DDS films during redox cycling is realized mainly by movement of the cations in aqueous solution and by movement of the anions in organic solvents, nevertheless the participation of anions in aqueous and cations in organic solvents is also established. The redox properties of PPy/DDS are more dependent on the solvent of the test solutions than of the synthesis solutions. Electronic Publication     

Multi-wall carbon nanotubes (MWCNTs)-doped polypyrrole DNA biosensor for label-free detection of genetically modified organisms by QCM and EIS

In this paper, we describe DNA electrochemical detection for genetically modified organism (GMO) based on multi-wall carbon nanotubes (MWCNTs)-doped polypyrrole (PPy). DNA hybridization is studied by quartz crystal microbalance (QCM) and electrochemical impedance spectroscopy (EIS). An increase in DNA complementary target concentration results in a decrease in the faradic charge transfer resistance (R_ct) and signifying “signal-on” behavior of MWCNTs-PPy-DNA system. QCM and EIS data indicated that the electroanalytical MWCNTs-PPy films were highly sensitive (as low as 4 pM of target can be detected with QCM technique). In principle, this system can be suitable not only for DNA but also for protein biosensor construction.     

Electrochemical impedance spectroscopy studies of organic-solvent-induced permeability changes in nanoporous films derived from a cylinder-forming diblock copolymer

In this paper we report electrochemical investigations of the influence of organic solvents dissolved in aqueous solution on the permeability of nanoporous films derived from a cylinder-forming polystyrene-poly(methyl methacrylate) diblock copolymer (CF-PS-b-PMMA). The nanoporous films (ca. 30 nm in pore diameter) were prepared on planar gold electrodes via UV-based degradation of the cylindrical PMMA domains of annealed CF-PS-b-PMMA films (30-45 nm thick). The permeability of the electrode-supported nanoporous films was assessed using cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The faradic current of Fe(CN)(6)(3-/4-) decreased upon immersion in aqueous solutions saturated with toluene or methylene chloride (5.8 mM and 0.20 M, respectively). EIS data indicated that the decrease in faradic current mainly reflected an increase in the pore resistance (R(pore)). In contrast, R(pore) did not change in a saturated n-heptane solution, 0.17 M ethanol, or 5.8 mM aqueous solutions of methylene chloride, diethyl ether, methyl ethyl ketone, or ethanol. Atomic force microscopy images of a nanoporous film in aqueous solution with and without 5.8 mM toluene showed a reversible change in the surface morphology, which was consistent with a toluene-induced change in R(pore). The solvent-induced increase in R(pore) was attributed to the swelling of the nanoporous films by the organic solvents, which decreased the effective pore diameter. The reversible permeability changes suggest that the surface of CF-PS-b-PMMA-derived nanoporous films can be functionalized in organic environments without destroying the nanoporous structure. In addition, the solvent-induced swelling may provide a simple means for controlling the permeability of such nanoporous films.     

电位型聚吡咯pH传感器的制备

电位型聚吡咯pH传感器的制备;聚吡咯; pH传感器; 电化学聚合; 交流阻抗