核黄素的微分脉冲溶出伏安分析

采用循环伏安法和微分脉冲溶出伏安法,对核黄素在裸金电极和巯基化合物分子自组装膜修饰金电极上的电化学行为进行了研究,发现在pH4.8的B-R缓冲溶液中,核黄素在裸金电极和分子自组装膜修饰金电极上均于-0.35V左右产生一对可逆的氧化还原峰。核黄素在裸金电极和谷胱甘肽、三巯基丙酸、二巯基苯丙咪唑分子自组装膜修饰金电极上,其浓度分别在3.0×10-7～2.3×10-4mol/L、1.05×10-6～2.0×10-4mol/L、2.1×10-6～2.08×10-4mol/L、1.05×10-6～2.0×10-4mol/L范围内与微分脉冲伏安峰峰电流之间有良好的线性关系,其相关系数分别为0.9932、0.9909、0.9857、0.9832,核黄素的检出限为2.1×10-7mol/L、5.2×10-7mol/L、8.6×10-7mol/L、5.2×10-7mol/L。对浓度为1.0×10-5mol/L的核黄素进行10次平行测定,所得峰电流的相对标准偏差为2.0%。将该方法用于核黄素片剂和复合维生素B片剂的测定,结果令人满意。     

碳纳米管修饰电极差示脉冲阳极溶出伏安法测定腺嘌呤

在HAc NaAc缓冲溶液中,玻碳电极上修饰的少量碳纳米管对腺嘌呤的氧化起增强作用.研究了腺嘌呤在修饰电极上的伏安行为,优化了电氧化的最佳条件,并对其进行含量测定.方法的线性范围为2.0×10-8～1.0×10-5mol/L,检出限为1.0×10-9mol/L.用于模拟样品中痕量腺嘌呤的测定,结果满意.     

碳糊电极上吸附伏安法测定痕量钪的研究

研究了钪(Ⅲ) 茜素氨羧络合剂(ALC)络合物在碳糊电极正电位区的吸附伏安行为,利用该络合物产生的二次导数吸附氧化峰电流与钪浓度成正比测定钪。其线性范围为2.0×10-9～6.0×10-7mol/L;富集120s,检出限达1.0×10-9mol/L(S/N=3)。探讨了电极反应机理。在同一支电极同一表面上15次连续测定4.0×10-8mol/L的Sc(Ⅲ),方法的相对标准偏差为3.7%。该法用于矿石样品中钪的测定,结果满意。     

聚L-色氨酸修饰电极的制备及对多巴胺的测定

研究了聚L 色氨酸修饰玻碳电极的制备及其多巴胺在该修饰电极上的循环伏安特性,建立了循环伏安法测定多巴胺的电化学分析新方法。在pH7.0的磷酸盐缓冲溶液中,用该电极测定多巴胺的线性范围为:2.0×10-6～5.0×10-4mol L,检测限为1.5×10-7mol L。已用于药剂中多巴胺的测定。     

有机磷农药在C16化学修饰电极上的伏安特性及分析应用

以C16作为修饰剂制备化学修饰电极,用于有机磷农药的伏安法测定.研究了支持电解液种类及酸度、修饰膜厚度、富集时间、扫描速度等因素对伏安曲线的影响,获得较为优化的测试条件.在0.1 mol/L柠檬酸缓冲液(pH 2.1)中,有机磷的浓度在4.0×10-7～2.0×10-5 mol/L范围内与还原峰电流呈良好线性关系(r=0.9989),检出限达8.0×10-8mol/L.多种金属离子和有机物质不干扰测定.该电极具有很好的重现性,在含1.2×10-5mol/L有机磷试液中连续测定10次,其RSD为1.2%.本法用于实际水样测定,结果满意.     

硒代蛋氨酸的电化学行为及其定量分析

本文采用循环伏安法(CV)研究了硒代蛋氨酸(SeMet)在银电极表面的电化学行为。实验发现,在0.03mol/L的硼砂 NaOH(pH9.5)介质中,于+0.30V(vs.SCE)电位下进行吸附,在-0.62V和-0.68V处获得一对氧化还原峰。探讨了SeMet在银电极表面的电极反应机理,并建立其定量分析方法。方法线性范围为2.0×10-11～8.0×10-9mol/L,检出限为4.0×10-12mol/L。该方法用于谷物样品中SeMet含量的测定,结果满意。     

壳聚糖共价键合化学修饰电极测定亚硝酸根

用共价键合法把壳聚糖修饰在玻碳电极表面,研究了NO-2在修饰电极上的阳极溶出伏安特性.实验结果表明:修饰电极在0.1 mol/L NaNO3(pH 2.60)底液中对NO-2有良好的吸附性和选择性,其峰电流与NO-2的浓度在1.5×10-6～1.0×10-3 mol/L范围内呈较好的线性关系;检测限可达2.0×10-7 mol/L.将壳聚糖修饰电极应用于雨水、湖水中NO-2的测定,结果满意.     

丹参酮ⅡA的电化学行为及其测定

应用循环伏安法研究丹参酮ⅡA在玻碳电极上的电化学行为并建立差示脉冲伏安法测定含量.在pH 4.0醋酸盐缓冲液中,差示脉冲伏安氧化峰电流与丹参酮ⅡA浓度(3.0×10-7~2.0×10-5mol.L-1)呈良好的线性关系,检测限为2.0×10-8mol.L-1.玻碳电极可有效消除样品中其它组分对丹参酮ⅡA测定的干扰,已成功用于实际样品中丹参酮ⅡA含量的直接测定.该方法灵敏度高、检测范围宽,结果令人满意.     

聚对硝基苯偶氮间苯二酚修饰电极伏安法测定多巴胺

采用循环伏安法研究了多巴胺(DA)在聚对硝基苯偶氮间苯二酚(p-nitrobenzenazo resorcinol,简称NBAR)膜修饰电极上的电化学行为,用差示脉冲伏安法对多巴胺的含量进行测定.结果表明,聚NBAR膜修饰电极对DA有明显的电催化作用.在pH4.0的磷酸盐缓冲液中,氧化峰电流与DA浓度在5.0×10-6~8.0×10-4mol/L范围内呈良好的线性关系,检测限为6.0×10-7mol/L.修饰电极可有效消除针剂中其它组分对DA测定的干扰,已用于实际样品DA含量的测定,结果令人满意.     

Zr(Ⅳ)-桑色素络合物在碳糊电极上的二次导数吸附伏安法测定Zr的研究

研究了Zr(Ⅱ)-桑色素络合物在碳糊电极正电位区的吸附伏安行为,并利用其在0.74V处的二次导数吸附氧化峰电流与Zr(Ⅳ)浓度为6.0×10-9～2.0×10-6 mol/L呈线性而测定Zr;检出限为3.0×10-9 mol/L(S/N=3).最佳测定条件为2.0 mol/L HCl、1.0×10-5 mol/L桑色素;富集电位为0V(vs.SCE);扫描速度为250 mV/s.该法不需萃取分离,可直接用于岩石样品中Zr的测定,结果满意.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.