Fabrication of chain-like Mn2O3 nanostructures via thermal decomposition of manganese phthalate coordination polymers

A novel manganese coordination polymer [Mn(Pht)(H₂O)]_n as a precursor was obtained by chemical precipitation involving an aqueous solution of anhydrous manganese acetate and phthalate anion as a potential O-banded ligand. Fourier transform infrared (FT-IR) results proved that phthalate anions coordinate to metal cations as a chelating bidentate ligand, making polymeric structure. The Mn₂O₃ nanostructures have been prepared via thermal decomposition of as-prepared manganese phthalate polymers as precursor in the presence of oleic acid (OA) and triphenylphosphine (TPP) as a stabilizer and capping. Different approaches such as FT-IR, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were applied to characterize the products. TEM images and XRD analysis indicated that the as-synthesized chain-like Mn₂O₃ has a crystal phase of cubic syngony with a mean size of ∼40 nm.     

Simple sonochemical synthesis and characterization of HgSe nanoparticles

Mercury selenide (HgSe) nanostructures were synthesized via a sonochemical method based on the reaction between HgCl(2), SeCl(4) and hydrazine hydrate (N(2)H(4)·H(2)O) in water, in presence of various capping agents. The effects of preparation parameters such as: the kind of capping agent and its amount, ultrasonic power, reaction time and temperature were investigated. It was found that morphology, particle size and phase of the products could be greatly affected by these parameters. HgSe nanostructures were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), photoluminescence spectroscopy (PL) and X-ray energy dispersive spectroscopy (EDS).     

一维纳米材料SmPO4·0.5H2O的制备及光学性质

以氧化钐和H₃PO₄为原材料,在无模板剂的情况下,用水热法通过调控pH、时间和温度制备了SmPO₄·0.5H₂O一维纳米材料,并提出其可能形成机理。用X射线粉末衍射（XRD）、透射电镜（TEM,HRTEM和SAED）、红外光谱（IR）和能谱（EDS）对产物的物相结构、微观形貌和组成进行了表征。用紫外-可见吸收光谱研究了产物的光学性质。研究结果表明,实验所制备的产物全部是六方晶系结构,形貌都为一维纳米线。反应体系的pH值、温度和时间的改变对纳米线的长径比有影响,但对其相结构基本都没有影响。分析得到最佳水热制备条件为pH=5、温度和时间分别为130℃和8 h,产物的结晶性、分散性和均匀性都达到最好。光学性质研究表明,该类产物在300~350 nm的紫外区域有吸收宽峰,是属于基质O^2-→P⁵⁺、Sm³⁺的电荷迁移。在350~450 nm处的可见光区域内也有一组吸收峰,是属于Sm³⁺的4f内层电子间的f-f跃迁吸收。依据该类吸收峰,得到禁带宽度在4.67~5.50 eV之间。pH值和温度对产物光学性能均有影响。     

花状硫化铜级次纳米结构的制备及可见光催化活性研究

本实验以氯化铜 (CuCl₂·2H₂O) 和二硫化碳(CS₂)为原料, 以乙二醇(C₂H₆O₂) 为溶剂, 通过溶剂热法成功制备了具有可见光活性的花状硫化铜(CuS) 级次纳米结构. 并利用X射线粉末衍射技术(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM) 等技术对其进行了表征, 利用紫外可见吸收光谱(Uv-vis)分析了其光学性能, 并以甲基橙为目标降解物对其可见光催化活性进行了研究. 结果表明: 花状CuS级次纳米结构具有很高的可见光催化活性, 与体相CuS粉末相比有很大的提高, 在自然光照射下对甲基橙的降解率可以达到100%. 同时本文对花状级次纳米结构的形成机理进行了分析. 关键词： 硫化铜 溶剂热 级次纳米结构 光催化     

Optical properties of carbon nanotubes and BaTiO3 composite thin films

Multiwalled carbon nanotubes and BaTiO₃ composite films have been prepared by pulsed-laser deposition technique at room temperature and high temperature of 600℃, separately. The structures of the composite films are investigated by using scanning electron microscopy and x-ray diffraction. The optical behaviours of the samples produced at different temperatures are compared with Raman spectroscopy, and UV-visible absorption. And the observation by Z-scan technique reveals that the composite films have a larger optical nonlinearity, and the samples prepared at high temperatures have better transmittance and opposite sign imaginary part of optical third-order nonlinearity.     

Fabrication, morphology, and photoluminescence properties of GaN nanowires and nanorods by ammoniating Ga2O3/V films on Si(1 1 1)

GaN nanowires and nanorods have been successfully synthesized on Si(1 1 1) substrates by magnetron sputtering through ammoniating Ga₂O₃/V films at 900 °C in a quartz tube. X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectrum were carried out to characterize the structure, morphology, and photoluminescence properties of GaN sample. The results show that the GaN nanowires and nanorods with pure hexagonal wurtzite structure have good emission properties. The growth direction of nanostructures is perpendicular to the fringes of (1 0 1) plane. The growth mechanism is also briefly discussed.     

Novel nanostructures of β-Ga2O3 synthesized by thermal evaporation

In this study, we report the novel β-Ga₂O₃ nanostructures synthesized by the thermal evaporation of Ga droplet in the presence of Au catalysts at 900 °C. The morphology and structure of the products were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The single-crystalline β-Ga₂O₃ nanosheets have lateral dimensions up to several tens of microns. Large arrays of column-like layered crystal β-Ga₂O₃ structures that consisted of many nanosheets were formed on the Au-coated silicon substrate under the suitable vapor concentration. These novel β-Ga₂O₃ nanostructures are expected to have potential application in functional nanodevices.     

Synthesis, structure and antiferromagnetic behaviour of brannerite MnV2O6

Brannerite MnV 2 O 6 with plate-like shape is successfully synthesized by hydrothermal method.Its crystal structure and morphology are investigated by x-ray diffraction (XRD),scanning electron microscopy (SEM),transmission electron microscope (TEM),high resolution transmission electron microscopy (HRTEM) and select area electronic diffraction (SAED).The results show that the brannerite MnV 2 O 6 with monoclinic structure has a uniform plate-like shape with a diameter of about 5-8 μm and a thickness of about 500 nm.SAED patterns further confirm the structure of the brannerite MnV 2 O 6 and the single crystalline character of the plate crystal.Magnetic properties are measured by superconducting quantum interference device (SQUID) in a temperature range of 2-300 K under a magnetic field of 1 T.The magnetic measurement results indicate that the material undergoes an antiferromagnetic transition with a N’eel temperature of 17 K.Above 50 K,the inverse susceptibility is fitted well to the Curie-Weiss law with a calculated moment of 5.98 μ B.Finally,the origin of antiferromagnetic behaviour in the brannerite MnV 2 O 6 is explained by means of Anderson model.     

Fabrication of flower-shaped Bi2O3 superstructure by a facile template-free process

A novel flower-shaped Bi₂O₃ superstructure has been successfully synthesized by calcination of the precursor, which was prepared via a citric acid assisted hydrothermal process. The precursor and Bi₂O₃ were characterized with respect to morphology, crystal structure and elemental chemical state by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It was shown that both the precursor and Bi₂O₃ flower-shaped superstructure were constructed of numerous nanosheets while the nanosheets consisted of a great deal of nanoparticles. Furthermore, key factors for the formation of the superstructures have been proposed; a mechanism for the growth of the superstructure has been presented based on the FESEM investigation of different growth stages.     

Controlled synthesis of BaWO4 hierarchical nanostructures by exploiting oriented attachment in the solution of H2O and C2H5OH

Shape-controlled synthesis of BaWO₄ hierarchical nanostructures has been successfully achieved by exploiting oriented attachment in a mixture of water and ethanol. A controlled change in the volume ratio of C₂H₅OH and H₂O or the concentration of initial reagents has resulted in the synthesis of products of various morphologies, such as shuttle-like, ellipsoid-like, and flower-like ones. The obtained products are characterized by field emission scanning electron microscopy, high-resolution transmission electron microscopy, X-ray powder diffraction, and Fourier transform infrared spectroscopy. The altered nucleation and growth rates of primary particles that assembled to the final hierarchical nanostructures through oriented attachment are the main cause of the evolution of their morphologies. The room-temperature photoluminescent intensities of the products strongly depend on their morphology.     

Effect of calcination temperature on the structure and hydroxylation activity of Ni0.5Cu0.5Fe2O4 nanoparticles

Nanocrystalline Ni_0.5Cu_0.5Fe₂O₄ was synthesized by sol-gel method with varying calcination temperature over the range of 500-1000. The powders obtained were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In addition, thermal analysis (TG-DTG-DTA) of the precursor was carried out. The study reveals the simultaneous decomposition and ferritization process at rather low temperature (280-350). For the crystalline structure investigated, single cubic spinel is gained when the precursor was decomposed at 800-1000, whereas separated crystal CuO formed when calcination temperature is below 800. The increase of calcination temperature favors the appearance of Fe_B³⁺, Cu_A²⁺ and O on the spinel surface. The hydroxylation activity is relative to the amount of Cu_B²⁺ species on the spinel surface. The lattice oxygen species on the spinel surface are favorable for the deep oxidation of phenol.     

Growth Mechanism and Characterization of Single-crystalline Ga-doped SnO2 Nanowires and Self-organized SnO2/Ga2O3 Heterogeneous Microcomb Structures

Ga掺SnO2单晶纳米线和SnO2/Ga2O3自组织异质微米梳是通过简单的热蒸发沉淀法一步制得的,并通过X射线粉末衍射(XRD)、场激发扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、X射线能量散射谱仪(EDS)、选区电子衍射谱(SAED)进行表征．从FE-SEM的图片上可以看出生成的产物具有纳米线和一种新的微米梳状形貌．XRD、SAED和EDS显示他们是单晶四角形的SnO2．产物的主干呈带状,纳米带阵列均匀的分布在主干的一侧或两侧．大量的Ga2O3纳米颗粒沉积在微米梳的表面．主干纳米带主要沿着[100]方向生长, 自组织的纳米带分支则在主干的(100)面上沿着[110]或者[110]方向生长．由于Ga的大量掺杂,光致发光谱的衍射峰发生红移并严重变宽．针对SnO2:Ga2O3异质微米梳的生长过程进行了解释,并讨论了实验条件对形貌的影响．     

Reentrant spin glass behavior in antiferromagnetic single crystalline Ba6Mn24O48 nanoribbons

Single crystalline Ba₆Mn₂₄O₄₈ nanoribbons with diameters ranging from one hundred nanometers to a few hundred nanometers and length up to tens of microns are synthesized via a facile molten salt method. These nanoribbons are characterized by a range of methods including X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), selected area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM). The magnetic properties of Ba₆Mn₂₄O₄₈ nanoribbons are investigated by the zero-field-cooled (ZFC), field-cooled (FC) magnetization, and ac susceptibility. Upon cooling, we find the reentrant spin glass (RSG) behavior in these nanoribbons, i.e., paramagnetic (PM), antiferromagnetic (AFM), and spin glass (SG). The RSG behavior might be due to the surface spin disorder, geometrical frustration and Mn³⁺/Mn⁴⁺ mixture in Ba₆Mn₂₄O₄₈ nanoribbons.     

2D atomic mapping of oxidation states in transition metal oxides by scanning transmission electron microscopy and electron energy-loss spectroscopy

Using a combination of high-angle annular dark-field scanning transmission electron microscopy and atomically resolved electron energy-loss spectroscopy in an aberration-corrected transmission electron microscope we demonstrate the possibility of 2D atom by atom valence mapping in the mixed valence compound Mn3O4. The Mn L(2,3) energy-loss near-edge structures from Mn2+ and Mn3+ cation sites are similar to those of MnO and Mn2O3 references. Comparison with simulations shows that even though a local interpretation is valid here, intermixing of the inelastic signal plays a significant role. This type of experiment should be applicable to challenging topics in materials science, such as the investigation of charge ordering or single atom column oxidation states in, e.g., dislocations.     

Synthesis of quasi-1D cuprous oxide nanostructure and its structural characterizations

A wealth of superfine polycrystalline cuprous oxide (Cu₂O) nanowires have been synthesized with hydrazine hydrated (N₂H₄·H₂O), act as the reducing agent, and Cu(OH)₂ nanowires, act as a soft template and surfactant, at room temperature. Two methods were employed for the synthesis of these nanowires, i.e. with and without capping agent (polyethylene glycol Mw 8000). Techniques of powder X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED) pattern, electron diffraction X-ray (EDX) spectroscopy, and UV-visible (UV-vis) spectroscopy have been used to characterize the morphology, structure, crystallinity, purity, and composition of nanowires. The average diameters of Cu₂O nanowires, prepared with and without capping agent, were observed to be 8-10 and 12-15 nm and lengths of several microns, respectively. It is found that capping agent (PEG) confines the dimensions of synthesized nanowires. In addition, the observed optical band gap of products show blue-shift effect compared to the bulk Cu₂O (E_g=2.17 eV), which ascribe it as a promising material for the conversion between solar energy and electrical or chemical energy.     

Microwave-assisted synthesis and optical property of CdMoO4 nanoparticles

Microwave-assisted synthesis is a novel method used to synthesize CdMoO₄ nanoparticles in propylene glycol. The effects of reaction time and microwave power on phase, morphologies, and optical properties of CdMoO₄ nanoparticles were studied, using X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and UV-visible spectroscopy. The present analyses proved that these crystalline powders were scheelite-type tetragonal structured CdMoO₄, with the crystallite size of 14-20 nm, and 4.51-4.73 eV band gaps, controlled by the synthetic conditions.     

Temperature controlled synthesis of SrCO3 nanorods via a facile solid-state decomposition rout starting from a novel inorganic precursor

Strontium carbonate nanorods have been successfully synthesized via solid-state decomposition of a new precursor, [Sr(Pht)(H₂O)₂]. The obtained nanorods were found to be orthorhombic with the length of 70-100 nm and the diameter of about 10-15 nm. The Effect of calcinations temperature on morphology and purity of the products has been investigated. Strontium carbonate nanorods were formed at 500 °C. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) spectroscopy. In addition, further evidence for the purity and stoichiometry of the product was obtained by XPS (X-ray photoelectron spectroscopy) spectrum.     

Room temperature synthesis of Cu2O nanocubes and nanoboxes

Monodisperse Cu₂O nanocubes are synthesized by reducing freshly prepared Cu(OH)₂ with N₂H₄·H₂O in water at room temperature. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations show that most of these nanocubes are uniform in size, with the average edge length of ∼500 nm. Selected area electron diffraction (SAED) investigation reveals that these nanocubes are single crystalline. Further, Cu₂O nanoboxes are obtained by etching Cu₂O nanocubes with acetic acid solution at room temperature. The nanoboxes retain the size and external morphology of the nanocubes.     

Rapid microwave-assisted hydrothermal synthesis of Bi12TiO20 hierarchical architecture with enhanced visible-light photocatalytic activities

Flower-like Bi₁₂TiO₂₀ hierarchical nanostructures composed of numerous nanobelts were synthesized at 180 °C within 1 h by a microwave-assisted hydrothermal method in the presence of cetyltrimethylammonium bromide (CTAB) for the first time. The as-prepared products were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and ultraviolet–visible (UV–vis) absorption spectroscopy. Furthermore, the hierarchical Bi₁₂TiO₂₀ nanostructures exhibited higher photocatalytic activities in the degradation of Rhodamine B under visible-light irradiation than that of the samples prepared without CTAB. In addition, the role of CTAB cationic surfactant has been investigated thoroughly and a possible mechanism is proposed.     

Synthesis and characterization of CoxZn1−xFe2O4 magnetic nanoparticles via a PEG-assisted route

We present an investigation of properties of Co_xZn_1−xFe₂O₄ (x=0.0-1.0) nanoparticles synthesized by a polyethylene glycol (PEG)-assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and vibrating scanning magnetometry (VSM) were used to characterize the structural, morphological and magnetic properties. The particle size obtained from TEM and XRD are consistent with each other. It was observed that the lattice constant for each composition decreases with increasing Co substitution and follows Vegard's law. Magnetization measurements show that while the materials with high Zn substitution are superparamagnetic at room temperature, they are ferromagnetic at temperatures lower than the blocking temperature. The materials with less Zn substitution are ferromagnetic below room temperature. Magnetizations and the coercivities of the samples decrease with the Zn substitution. The resultant overall magnetic behavior of the superparamagnetic samples are found to be considerably different than that of conventional superparamagnetic systems due to the antiferromagnetic interactions both in intra- and inter-cluster spins, and size (effective moment) distribution of the particles.