表面活性剂辅助二氧化硅纳米颗粒在非水基液中的分散研究（英文）

研究了粒径10~100nm的二氧化硅纳米颗粒在非水基液中的表面活性剂辅助分散。结合颗粒表面特定官能团结构,针对性选择了合适的表面活性剂,氢键桥梁作用和长链分子空间位阻作用抑制了颗粒团聚行为。当表面活性剂体积分数6%的时候,动态光散射测试结果表明颗粒中位尺度30.2nm,与透射电镜测试结果吻合,展现了良好的分散性。     

金纳米流体的电场可调光学性质

利用多次还原法制备了不同粒径的金纳米颗粒,SEM和粒度分析表明其平均粒径分别为11 nm,35 nm和58 nm.进一步通过表面活性剂辅助的液相转移法制备出不同粒径的油基金纳米流体,测试了金纳米流体在电场作用下的光学性质.结果表明金纳米流体在电场作用下表现出明显的双折射现象,且随电场强度的变化双折射具有可调节性.金颗粒粒径和浓度对折射率有明显影响,在实验采用的浓度范围内,折射率随金颗粒浓度和粒径的增加而减小.最后,利用电流变液结构转变机理对金纳米流体的电致双折射进行了分析. 关键词： 纳米流体 双折射 电流变液     

ZnO胶体的可见发射和表面修饰特性

利用化学方法在常温下成功地制备了ZnO胶体,颗粒尺寸在5nm以下,其量子限域效应十分明显。通过跟踪测试样品的吸收谱,估价了带边吸收与胶体颗粒大小的关系,并研究了随着胶体颗粒的长大,可见发射强度的变化。通过添加表面活性剂,使粒子的表面得到修饰,从而增强了紫外发射。同时对可见发射机制进行了探讨,指出绿带发射至少部分是来自表面浅陷阱(如单离子氧空位)电子到深陷阱空穴的跃迁。     

Enhancement in Magnetorheological Effect of Magnetorheological Elastomers by Surface Modification of Iron Particles

为了研制具有高磁流变效应的磁流变弹性体,从新的化学修饰的角度制备了各向异性的橡胶基磁流变弹性体. 阴离子表面活性剂、非离子表面活性剂和复合表面活性剂等三种不同类型的表面活性剂分别用于修饰铁颗粒. 使用力磁耦合动态测试仪测量磁流变弹性体的动态剪切模量,并计算材料的磁流变效应. 测试结果表明,当Span 80的含量为15%时,材料的相对磁流变效应可达到188%,除了表面活性外,Span 80的增塑效应也有利于相对磁流变效应的增加. 当使用具有强表面活性的复合表面活性剂修饰铁颗粒时,用量只需0.4%,便可使相对     

表面活性剂对气-液界面纳米颗粒吸附规律的影响

通过测定及分析纳米颗粒和表面活性剂-纳米颗粒复配体系在自由吸附过程与动态收缩过程中表面张力的变化,总结了纳米颗粒在气-液界面的吸附排布规律以及表面活性剂对其吸附规律的影响.实验结果表明,自由吸附过程中,随矿化度增加、阳离子活性剂浓度增加,平衡表面张力降低,这与颗粒吸附密度增加及颗粒润湿性改变有关.浓度低于临界胶束浓度(CMC)时,阳离子活性剂体系与混合体系的表面张力差异证明了阳离子活性剂可以通过静电作用吸附于纳米颗粒表面,进而部分溶解于水相;而阴离子活性剂与纳米颗粒相互作用力较弱,对表面张力影响较小.纳米颗粒体系在液滴收缩过程中,表面张力从自由吸附平衡态进一步降低大约9 m N/m,说明自由吸附过程中纳米颗粒不能达到紧密排布;同时表面张力呈现为缓慢降低、快速降低和达到平衡三部分,表面压缩模量可达70 m N/m,满足了液膜Gibbs稳定准则,这将有助于提高泡沫或者乳液稳定性.纳米颗粒-表面活性剂体系在液滴收缩过程中表面张力降低值随活性剂浓度增加而减小;表面压缩模量由高到低依次为:纳米颗粒>阳离子活性剂-纳米颗粒>阴离子-纳米颗粒>表面活性剂.     

SnO$lt;sub$gt;2$lt;/sub$gt;纳米晶体的制备、结构与发光性质

使用软化学方法在碱性溶液中制备出了颗粒尺寸分布均匀的SnO₂纳米颗粒,使用透射电子显微镜（TEM）、X射线衍射（XRD）、光致发光谱（PL）和光吸收谱等方法分析与表征了SnO₂纳米颗粒的结构和光学性能.实验中通过表面活性剂的加入来控制纳米颗粒的结晶与凝聚.XRD,TEM的结果表明,原始制备出的SnO₂纳米颗粒的平均粒径小于4 nm,为完好的晶体状态.纳米颗粒经过400—1000 ℃退火后晶粒尺寸进一步增大.光吸收谱表明,相对于体材料,纳米颗粒的禁带宽度展宽并随颗粒尺寸增大而红移.光致发光谱测试表明,不同温度下退火的SnO₂纳米颗粒在350—750 nm有较强的发光,研究表明这是来源于颗粒表面的氧空位缺陷发光. 关键词： 氧化锡 表面活性剂 纳米颗粒 光致发光     

银纳米颗粒对Tm3+/Yb3+共掺铋锗酸盐玻璃上转换发光性能的影响

利用传统熔融淬冷法制备了系列Tm3+/Yb3+共掺复合银纳米颗粒铋锗酸盐玻璃样品.测试得到表征银纳米颗粒存在的表面等离子体共振(SPR)峰位于556～581 nm,透射电镜图像中观察到均匀分布的Ag纳米颗粒,尺寸约为5～25 nm.通过测试玻璃样品在400～900 nm波段的上转换光谱,对铥镱共掺复合银纳米颗粒铋锗酸盐...     

纳米Fe3O4磁性液体稳定性的研究

从理论上解析了磁性颗粒之间的相互作用对纳米磁性液体稳定性的影响 ,指出磁粒半径和浓度 ,表面活性剂的包覆是影响磁液稳定性的重要因素 .采用湿化学共沉淀法制备了纳米Fe3O4 磁性液体 ,经过TEM等手段的表征 ,证明平均粒径为 10nm ,稳定性良好 .实验研究了加料方式、搅拌速度、分散作用、表面活性剂包覆时机、包覆时间和加入量以及pH值诸多工艺因素对磁液稳定性的影响 ,并分析了这些因素的影响机制     

α-烯烃减阻聚合物隔离包覆中吸附过程的分子动力学模拟

采用分子动力学模拟方法,在α-烯烃聚合物颗粒聚氨酯类隔离体包覆机理的基础上,对α-烯烃减阻聚合物隔离包覆过程所涉及的吸附过程进行了研究. 结果表明,不同表面活性剂与同一多元羟基化合物、不同多元羟基化合物与同一表面活性剂相互之间的作用类似,呈现出吸附分布程度不同、与颗粒表面接近程度不一的现象,通过模拟给出了接近程度的顺序;包覆过程中进行的加成聚合反应其控制步骤为吸附传质过程,多元羟基化合物的分布离颗粒表面越近,越利于其与异氰酸酯在表面进行反应,模拟结果给出了表面活性剂和多元羟基化合物的选择配伍关系.     

ZnS:Mn纳米晶的制备及其发光性能研究

以C19H42BrN为表面活性剂,采用水热法合成了ZnS:Mn纳米晶,分别利用XRD、TEM、荧光光谱仪对其物相、形貌及光学性能进行了研究。结果表明:ZnS:Mn纳米晶为闪锌矿ZnS结构,颗粒近似球形,平均粒径为4～8 nm。荧光光谱显示,ZnS:Mn纳米晶的荧光发射峰强度随着Mn2+掺杂浓度和表面活性剂含量的增加而逐渐增强。     

Effect of pyrogallol-poly(ethylene glycol) on stabilization,structure, and interparticle potential of concentrated nickel nanoparticle suspensions

Nickel nanoparticles with an average diameter of 90 nm have been dispersed in de-ionized water with addition of pyrogallol-poly(ethylene glycol) polymers, hereafter termed Gallol-PEG, of different molecular weights as a surfactant. Measurement of zeta potential, infrared spectrum, and adsorption isotherm confirms the preferential anchoring from polar end of the surfactant molecules on the particle surface, forming a Langmuir-typed adsorption layer (adlayer) to provide an electrosteric stabilization. Concentrated nanoparticle suspensions with a solids loading up to 40 vol.% and an apparent viscosity lower than 10 Pa s at a shear rate of 100 s⁻¹ have been obtained, indicating that the Gallol-PEG adsorption is effective in facilitating the suspension flow under stress. The suspensions are yet fractal in structure with an experimentally determined fractal dimension of 2.1, revealing that a reaction-limited cluster–cluster aggregation is operative. This weakly coagulated fractal structure stems primarily from the shallow interparticle attraction operative over a moderate interparticle separation (~5–10 nm), and is prone to the adlayer thickness and the molecular conformation of the surfactant.     

Facile synthesis and characterization of SnTe films

In this paper, we reported a novel, simple, and cost-effective route to SnTe films. The films were prepared by a chemical bath method, at room temperature and ambient pressure, using conventional chemicals as starting materials with or without surfactant. The films were characterized by X-ray diffraction, X-ray photoelectron spectroscopy and field-emission scanning electron microscopy, respectively. The SnTe film deposited without surfactant consists of nanoparticles (∼100 nm). The film deposited using polyethyleneglycol (PEG) as the surfactant consists of nanoparticles with size of ∼25 nm, whereas the film deposited using polyvinylpyrrolidone (PVP) as the surfactant consists of rough rod-like nanostructures (∼50 in diameter and ∼500 nm in length), besides nanoparticles (∼40-180 nm). The SnTe film deposited with PEG is smoother and denser. The formation mechanism of the SnTe films was proposed.     

Morphology and magnetic properties of CeCo5 submicron flakes prepared by surfactant-assisted high-energy ball milling

CeCo₅ permanent magnetic alloy has been processed by surfactant assisted high energy ball milling. Heptane and oleic acid were used as the solvent and surfactant, respectively. The amount of surfactant used was 50% by weight of the starting powder. The produced particles were deposited on a piece of copper (4 mm in length and width) under a magnetic field of 27 kOe applied along the copper surface and immobilized by ethyl α-cyanoacrylate. Scanning electron microscope pictures show that the particles are flakes, several μm in length and width and tens of nm in thickness. X-ray diffraction patterns and magnetic measurements prove that the flakes are crystalline with c-axes magnetic anisotropy. The easy magnetization axis is oriented perpendicular to the surface of the flake. A maximum coercivity of 3.3 kOe was obtained for the sample milled for 40 min.     

Temperature-induced micelle transition of gemini surfactant in aqueous solution

The viscosity and morphology of gemini surfactant in aqueous solution at various temperatures are investigated by rheometer and transmission electron microscopy with a freeze fracture replication technique. The viscosity of 18-3-18 or 16-3-16 reaches its maximum when the solution temperature is near the Krafft temperature of the surfactant. The morphology of a gemini surfactant in aqueous solution is strongly influenced by the temperature: vesicles or sphere-like aggregates are formed in the dilute solution of 18-3-18 under 25 °C environment; when the solution temperature goes up to 50 °C, such aggregates will transit to worm-like micelles with the length of each from 100 nm to 400 nm; meanwhile, the increase of concentration may lead to the formation of network; however, the worm-like micelles or network will transit to vesicles or sphere-like aggregates again when the temperature reaches 80 °C.     

ZnO粉末的直流电致发光特性研究

用溶胶凝胶法制备了几种ZnO粉末, 测量了它们的直流电致发光. 在样品中观察到了较强的绿带（556 nm）发射; 对十二胺处理的样品, 绿带发光强度最高可提高8倍, 十八胺处理的样品, 绿带发光强度最高可提高12倍. 在同电压下, 十八胺处理的ZnO的发光强度也较十二胺处理的ZnO的发光强度大1.5～2倍; 并在十二胺处理的样品中, 还观察到了强度较小的蓝光谱带（406 nm）. 在一定电压范围内, ZnO电致发光强度随直流电压增强而线性增强. 所得ZnO样品在2V/μm场强下起亮, 在测量的近1 h内, 发光强度稳定, 重复性好. 分析认为：406 nm处的蓝光谱带是由于VZn空位在禁带中（距离价带0.3 eV）形成缺陷能级, 从导带到价带跃迁的结果, 而556 nm处的绿色发射带是由ZnO中氧空位所导致.     

Small angle neutron scattering study of two nonionic surfactants in water micellar solutions

Two classic nonionic surfactants — C₁₄E₇ (heptaethylene glycol monotetradecyl ether) and C₁₀E₇ (heptaethylene glycol monodecyl ether) were investigated in heavy water solution for concentration c = 0.17% (dilute regime) at different temperatures in the range t = 10–35°C by small angle neutron scattering (SANS) method. In the case of C₁₄E₇ surfactant — for all temperatures at c = 0.17% there are two axial ellipsoidal micelles with longer axis 15 nm at 10°C and 49.5 nm at 35°C in investigated solutions. For C₁₀E₇ surfactant at the same concentration of solution and temperature — two axial ellipsoidal micelles were observed, too. The longer axis is equal to 7.5 nm at 10°C, 9 nm at 20°C and at 35°C this axis is equal to 12 nm. Micelles of C₁₀E₇ nonionic surfactant are smaller than those of C₁₄E₇ surfactant in the same experimental conditions.      

溶剂热法合成水溶性B-PEI/NaYF4∶Yb3+,Er3+ 上转换发光纳米粒子

以枝状聚乙烯亚胺(Branched polyethylenimine,B-PEI)为表面活性剂,水和二乙二醇作为溶剂,采用溶剂热法合成出尺寸为45 nm左右的水溶性B-PEI/NaYF₄∶Yb³⁺, Er³⁺纳米粒子。在室温980 nm光激发下,样品显示出较强的上转换发光。样品表面的B-PEI分子中的氨基可以连接生物分子。细胞毒性实验显示样品具有较低的细胞毒性。以上结果可以为上转换发光纳米粒子在生物医学领域的应用提供有益的参考。     

Influence of a surfactant on hyperfine magnetic interactions in goethite nanoparticles

Structural and magnetic characteristics of nanosized goethite (α-FeOOH) samples prepared by chemical precipitation of an iron (III) salt and alkali in aqueous solutions with different contents of a surfactant (ethyl alcohol) have been investigated. Changes in the morphology, structure, and sizes of antiferromagnetic nanoparticles, caused by the presence of the surfactant in the deposition solution, have been established by Mössbauer spectroscopy, magnetic measurements, X-ray diffraction, and electron microscopy. It is determined that an increase in the surfactant concentration leads to the bimodal size distribution of nanoparticles; in this case, the fraction of small (<10 nm) isolated particles in the sample increases and the degree of ordering of larger particles (50–100 nm) increases with a change in their shape from spherical to needle-like.     

Optimization of Preparation Techniques for Poly(Lactic Acid-Co-Glycolic Acid) Nanoparticles

Microparticles and nanoparticles of poly(lactic acid-co-glycolic acid) (PLAGA) are excellent candidates for the controlled release of many pharmaceutical compounds because of their biodegradable nature. The preparation of submicron PLAGA particles poses serious challenges that are not necessarily present when preparing microparticles. We have evaluated several combinations of organic solvents and surfactants used in the formulation of PLAGA nanoparticles. Critical factors such as the ability to separate the nanoparticles from the surfactant, the ability to re-suspend the nanoparticles after freeze-drying, formulation yield and nanoparticle size were studied. The smallest particles were obtained using the surfactant/solvent combination of sodium dodecyl sulfate and ethyl acetate (65 nm) and the largest particles were obtained using poly(vinyl alcohol) and dichloromethane (466 nm). However, the optimal nanoparticles were produced using either acetone or ethyl acetate as the organic solvent and poly(vinyl alcohol) or human serum albumin as the surfactant. This is because the most critical measure of performance of these nanoparticles proved to be their ability to re-suspend after freeze-drying.     

Strong Band-Edge Emission from ZnS Quantum Dots Stabilized by Gum Arabic

ZnS quantum dots （QDs）, prepared by soft-condensation, exhibit robust structure of a quantum size equal 3.13 nm mediated two-dimensional gum Arabic surfactant as characterized by scan tunnelling microscope （STM）. Strong blue-shifted absorption and emission bands are depicted by optical characterization even for the sample stored under ambient condition for two weeks. These enhancements can be attributed to the completely passivated surface trap states by Gum Arabic.