室温下Pr0.7Ca0.3MnO3薄膜的瞬态光响应特性

在室温下利用波长532nm，脉冲宽度7ns的纳秒脉冲激光研究了不同电压和激光能量密度作用下Pr_0.7Ca_0.3MnO₃薄膜的瞬态光响应特性.在激光能量密度为275.16mJ/cm²时，其最大电阻变化率达到92.3%，响应时间约36ns.室温下电压变化对薄膜的光响应特性影响不大，而诱导光能量密度的影响则很明显，能量密度越大，电阻变化越大，响应时间越短，并且电阻变化和响应时间均与激光能量密度呈非线性关系.这种光响应来源于薄膜中的光致非稳态绝缘体-金属相变，有望在新型光电器件上获得应用.     

La0.67Sr0.33MnO3薄膜光响应特性研究

实验测量了在不同温度和电场下,超巨磁电阻CMR(colossal magnetoresistance)薄膜材料La_0.67Sr_0.33MnO₃(LSMO)的光响应特性.发现样品被激光照射后,具有光诱导电阻变化的特性.在温度小于居里点Tc时,电阻随温度升高而增大,在Tc以上时,电阻则随温度升高而减小.通过对样品的光脉冲响应和偏置电场的关系分析,可认为其光响应特性的机理与激光激励下引起的自旋系统变化有关.     

Fe3O4/MgO(100)薄膜外场诱导电阻变化特性

采用激光分子束外延（L-MBE）方法,以MgO(100)为基底生长了Fe3O4单晶薄膜, 研究了Fe3O4/MgO(100)薄膜外场（温度、磁和激光场）诱导电阻变化特性。X射线衍射(XRD)分析表明Fe3O4薄膜是沿MgO(200)晶面外延生长的单晶薄膜;反射高能电子衍射（RHEED）强度振荡曲线分析表明Fe3O4薄膜表面平整,而且生长模式为2维层状生长;原子力显微镜（AFM）分析表明Fe3O4薄膜表面粗糙度为0.201 nm,说明薄膜表面达到原子级平整度。外场作用下Fe3O4薄膜的电阻测试表明:薄膜样品的电阻在120 K(Verwey转变温度)出现一峰值,略微下降后继续增大, 展现出半导体型的导电特性; 在激光作用下,整个测量温度范围内薄膜样品的电阻减小,样品展示出瞬间光电导的特性;从降温曲线可以看出, Verwey转变温度由无激光作用时的120 K上升到有激光作用时的140 K; 光致电阻变化率随着温度的降低而增大,这主要是由于激光作用导致电荷有序态的退局域化。     

脉冲激光沉积温度及氧压对Bi2Sr2Co2Oy热电薄膜晶体结构与电输运性能的影响

利用脉冲激光沉积技术在c-Al₂O₃单晶基片上制备了Bi₂Sr₂Co₂O_y热电薄膜并研究了沉积温度和氧压对薄膜晶体结构及电输运性能的影响.在最佳沉积条件下制备的单相、c轴取向的Bi₂Sr₂Co₂O_y薄膜的室温电阻率ρ和塞贝克系数S分别为2.9mΩ/cm和110μupV/K,其功率因子S²/ρ好于在单晶样品上得到的值.此外,该薄膜在低温下表现出较强的负磁阻效应,在2K,9T时达到了40%.     

巨磁电阻材料La0.9Sr0.1MnO3与半导体Si组成的二极管的整流特性

掺杂锰氧化物La_0.9Sr_0.1MnO₃薄膜被直接沉积在n型 硅基片上，构成p-n结.这种p-n结在很宽的温度范围内都有很好的整流特性.研究结果表明， 这种p-n结的结电阻对低磁场敏感，在3×10^-2T的磁场下，磁电阻可达70％.磁 电阻的正负依赖于温度.磁电阻的大小可通过加在p-n结上的电压调节.     

Co掺杂对铁磁金属La0.8Sr0.2MnO3磁电阻影响机理

通过对La_0.8Sr_0.2Mn_1-yCo_yO₃(y≤02)饱和磁矩和输运的测量,研究了Co对La_0.8Sr_0.2MnO₃的磁电阻影响机制.结果表明,在La_0.8Sr_0.2Mn_1-yCo_yO₃（y≤02）中Co³⁺离子是低自旋态.由于Mn³⁺—O—Co³⁺—O—Mn³⁺类型的磁交换与Mn³⁺-Mn⁴⁺离子间双交换作用相比较弱,Curie温度T_C附近的磁电阻随着Co掺杂量的增加而降低.与此相反,由于Co²⁺离子与e_g巡游电子的反铁磁交换耦合作用,低温区间的磁电阻随着Co掺杂量的增加而升高.     

Cu掺杂La0.67Sr0.33CuxMn1-xO3薄膜的光诱导效应研究

分别采用溶胶-凝胶和射频磁控溅射的方法制备了La_0.67Sr_0.33Cu_xMn_1-xO₃（x=0.05, 0.10和0.15）系列块材和薄膜,研究了Cu部分替代对薄膜光诱导特性的影响.实验结果表明随着Cu掺杂量的增加,薄膜的金属-绝缘转变温度向低温方向移动,且导电性降低.在金属相激光作用诱导电阻增大.光致电阻相对变化极大值随着Cu含量的增加而增大,当 关键词： 锰氧化物 光诱导 Cu掺杂 晶格效应     

He+辐照对Ga0.94Mn0.06As薄膜铁磁性的改善

离子辐照半导体可以很好的改善半导体材料的磁学性质.用He⁺ 辐照Ga_0.94Mn_0.06As薄膜,可以较方便的调制Ga_0.94Mn_0.06As 薄膜中产生铁磁性载体的浓度.由于空穴居间而导致Ga_0.94Mn_0.06As薄膜的铁磁性, 可以通过He⁺的辐照来得到改善,其结果是Ga_0.94Mn_0.06As薄膜的矫顽力可以增加3倍多. 当He⁺辐照流强增加时, 居里温度和沿着样品面外磁化难轴方向的饱和磁场都减小了. 被辐照的Ga_0.94Mn_0.06As薄膜的电学性质和结构特征显示, He⁺辐照Ga_0.94Mn_0.06As薄膜可以有控制地改善它的铁磁性, 其结果源于He⁺辐照Ga_0.94Mn_0.06As薄膜所诱导产生电缺陷对空穴的补偿, 而不是He⁺辐照改变了Ga_0.94Mn_0.06As薄膜的结构.     

Al2O3增强的Co2-C98/Al2O3/Si异质结的光伏效应

随着能源危机的加剧,太阳能电池作为开发和利用太阳能的一种普遍形式, 日益受到世界各国的重视.随着太阳能电池向着高效率、薄膜化、无毒性和原材料丰富的方向发展, 单纯的硅系太阳能电池已经无法达到这样的要求,因此新的材料和工艺的开发利用迫在眉睫. 本文研究了碳材料在硅异质节上实现光伏效应的改善及其可能在太阳能电池上的应用. 采用脉冲激光沉积方法制备的Co₂-C₉₈/Al₂O₃/Si异质结构在标准日光照射 (AM1.5, 100 mW/cm²)条件下,可获得0.447 V的开路电压和18.75 mA/cm²的电流密度, 转换效率可达3.27%.通过电容电压特性和暗条件下的电输运性能测量, 证明了氧化铝层的引入不但对单晶硅的表面起到了物理钝化作用,减小了反向漏电流, 使异质结界面缺陷、界面能级和复合中心减少,还起到了场效应钝化作用, 增加了异质结界面的势垒高度,增加了开路电压,使异质结的光伏效应显著增强.     

n-ZnO:Al/i-ZnO/n-CdS/p-Cu2ZnSnS4太阳能电池光伏特性的分析

具有高光吸收系数的半导体Cu₂ZnSnS₄ (CZTS)薄膜是一种新型太阳能电池材料. 本文对n-ZnO:Al/i-ZnO/n-CdS/p-CZTS结构的CZTS薄膜太阳能电池进行分析, 讨论CZTS薄膜的掺杂浓度、厚度、缺陷态和CdS薄膜的掺杂浓度、 厚度对太阳能电池转换效率的影响以及太阳能电池的温度特性. 分析表明, CZTS薄膜作为太阳能电池的主要光吸收层, CZTS薄膜的掺杂浓度和厚度的取值对太阳能电池的转换效率有显著影响, CZTS薄膜结构缺陷态的存在会导致太阳能电池性能的下降. CdS缓冲层的掺杂浓度、厚度对太阳能电池光伏特性的影响较小. 经结构参数优化得到的n-ZnO:Al/i-ZnO/n-CdS/p-CZTS薄膜太阳能电池的最佳光 伏特性为开路电压1.127 V、短路电流密度27.39 mA/cm²、填充因子87.5%、 转换效率27.02%,转换效率温度系数为-0.14%/K.     

Photocontrol of magnetization in Al-substituted Fe3O4 thin films

Thin films of (111)-oriented spinel ferrite Al_0.5Fe_2.5O₄ have been prepared by a pulsed-laser deposition (PLD) technique on α-Al₂O₃ (0001) substrates. The films exhibit cluster-glass behaviors with a spin-freezing temperature, T_g, near or above room temperature. The magnetization was found to increase following light irradiation below T_g, which indicates the photoinduced melting of cluster-glass states. An analysis comparing the dynamic behavior of magnetic response to light irradiation between zero-field-cooled (ZFC) states and field-cooled (FC) states at 10 K under various light intensities, I, revealed that the direct photoexcitation of spins occurs when I≤0.78 mW/mm², while the thermal heating effect following the light absorption of the samples also contributes to the enhancement of magnetization when I≥1.22 mW/mm². The magnetization of the films could be controlled by light irradiation even at room temperature. This suggests the possibility of utilizing these films in the development of novel magneto-optical memory devices.     

Preparation of the La0.8Sr0.2MnO3 films on STO and LAO substrates by excimer laser-assisted metal organic deposition using the KrF laser

La_0.8Sr_0.2MnO₃ films were prepared on SrTiO₃ (STO) and LaAlO₃ (LAO) substrates using excimer laser-assisted metal organic deposition (ELAMOD). For the LAO substrate, no epitaxial La_0.8Sr_0.2MnO₃ film was obtained by laser irradiation in the fluence range from 60 to 110 mJ/cm² with heating at 500 °C. On the other hand, an epitaxial La_0.8Sr_0.2MnO₃ film on the STO substrate was formed by laser irradiation in the fluence range from 60 to 100 mJ/cm² with heating at 500 °C. To optimize the electrical properties for an IR sensor, the effects of the laser fluence, the irradiation time and the film thickness on the temperature dependence of the resistance and temperature coefficient of resistance (TCR: defined as 1/R·(dR/dT)) of the LSMO films were investigated. An LSMO film on the STO substrate that showed the maximum TCR of 3.9% at 265 K was obtained by the ELAMOD process using the KrF laser.     

Photoinduced second-order optical susceptibilities of Er2O3 doped TeO2-GeO2-PbO glasses

Second-order optical susceptibilities were established in the optically poled erbium doped tellurite glasses near the melting temperature. The non-linear optical susceptibility was formed by bicolor coherent optical treatment performed by two coherent laser beams originated from 50 ps Nd-YAG laser (λ = 1.32 μm) exciting the high pressure hydrogen laser cell emitting at 1907 nm. The non-centrosymmetric grating of the medium was created by coherent superposition of the fundamental laser illumination at 1907 nm and the doubled frequency one at 953.5 nm. The maximally all-optically poled SHG occurs for 2% doped Er₂O₃ (in weighting units) TeO₂-GeO₂-PbO glass. It was found that the photoinduced SHG demonstrates a saturation during the photo-treatment of 9-10 min using the two beams polarized at angle about 45° between them. During the coherent bicolor optical treatment it was achieved the value of second-order susceptibility up to 3.6 pm/V at 1907 nm. The optimal ratio between the fundamental beam with power density about 1.1 GW/cm² and writing doubled frequency seeding beam about 0.015 GW/cm² corresponds to the maximal of photoinduced SHG. For glasses with lower concentration of Er₂O₃, the relaxation of the second-order optical susceptibility is substantially longer and achieves SHG value that corresponds to 80% of the maximal ones. It is necessary to emphasize that efficient optically-poled grating exists only within the narrow temperature range near the glassing temperature. Possible physical mechanisms of the phenomenon observed are discussed. Generally the used glasses possess better parameters than early investigated germinate glasses.     

Relaxation in the photoelectric and photovoltaic responses of thin-film Pb(Zr0.25, Ti0.75)O3 ferroelectric

We study the relaxation of photoresponses in self-polarized Pb(Zr_0.25, Ti_0.75)O₃ film structures with a semitransparent NiCr top electrode under focused laser illumination with a wavelength of 0.63 μm and a power of about 40 mW. Dependences of the relaxation times of the photoresponses on the field directed both along the self-polarization vector and opposite to it are experimentally obtained. The dependences are found to be qualitatively different. We assume that in the structure under study, a screening charge occurs due to the capturing of photoinduced carriers in deep traps localized in the contact region.     

锰位铁掺杂La0.67Sr0.33FexMn1-xO3薄膜的光诱导效应

分别采用溶胶-凝胶法和脉冲激光沉积的方法制备了La_067Sr_033Fe_xMn_1-xO₃(x=0, 005, 010, 015)系列块材和薄膜,研究了Fe部分替代对La_067Sr_033Fe_xMn_1-xO₃薄膜 关键词： 光诱导 Fｅ掺杂 晶格效应     

High temperature thermoelectric properties of highly c-axis oriented Bi2Sr2Co2Oy thin films fabricated by pulsed laser deposition

High-temperature thermoelectric transport property measurements have been performed on the highly c-axis oriented Bi2Sr2Co20v thin films prepared by pulsed laser deposition on LaA1Oa （001）. Both the electric resistivity p and the seebeck coefficient S of the film exhibit an increasing trend with the temperature from 300 K-1000 K and reach up to 4.8 m. cm and 202 V/K at 980 K, resulting in a power factor of 0.85 mW/mK which are comparable to those of the single crystalline samples. A small polaron hopping conduction can be responsible for the conduction mechanism of the film at high temperature. The results demonstrate that the Bi2Sr2Co2Oy thin film has potential application has high temperature thin film thermoelectric devices,     

Effect of CO2 laser irradiation on the transport properties of La0.67Ba0.33MnO3 thin film

The effect of CO₂ laser irradiation on La_0.67Ba_0.33MnO₃ epitaxial thin film was investigated. Epitaxial thin films grown by pulsed laser deposition were irradiated by a CO₂ laser in air for 10-60 s. It is shown that after CO₂ laser irradiation treatment, the crystallinity of the film is strongly enhanced. It is found that a dramatic decrease in the resistivity of the CO₂-laser-irradiated film is accompanied by a remarkable increase in its insulator-metal transition temperature and the temperature coefficient of resistance. This significant improvement of its structure and properties is achieved in several dozens of seconds and surpasses that observed in films annealed in an oxygen atmosphere at 900 ^°C for 12 h, suggesting that CO₂ laser irradiation is a new and effective tool to optimize CMR manganites for bolometric applications.     

Influence of the laser wavelength on the epitaxial growth and electrical properties of La0.8Sr0.2MnO3 films grown by excimer laser-assisted MOD

Epitaxial La_1−xSr_xMnO₃ (LSMO) films were prepared by excimer laser-assisted metal organic deposition (ELAMOD) at a low temperature using ArF, KrF, and XeCl excimer lasers. Cross-section transmission electron microscopy (XTEM) observations confirmed the epitaxial growth and homogeneity of the LSMO film on a SrTiO₃ (STO) substrate, which was prepared using ArF, KrF, and XeCl excimer lasers. It was found that uniform epitaxial films could be grown at 500 °C by laser irradiation. When an XeCl laser was used, an epitaxial film was formed on the STO substrate at a fluence range from 80 to 140 mJ/cm² of the laser fluence for the epitaxial growth of LSMO film on STO substrate was changed. When the LaAlO₃ (LAO) substrate was used, an epitaxial film was only obtained by ArF laser irradiation, and no epitaxial film was obtained using the KrF and XeCl lasers. When the back of the amorphous LSMO film on an LAO substrate was irradiated using a KrF laser, no epitaxial film formed. Based on the effect of the wavelength and substrate material on the epitaxial growth, formation of the epitaxial film would be found to be photo thermal reaction and photochemical reaction. The maximum temperature coefficient of resistance (TCR) of the epitaxial La_0.8Sr_0.2MnO₃ film on an STO substrate grown using an XeCl laser is 4.0%/K at 275 K. XeCl lasers that deliver stabilized pulse energies can be used to prepare LSMO films with good a TCR.     

La0.88 Te0.12 MnO3/Si异质结的整流和光伏特性研究

采用脉冲激光沉积法制备了La_0.88Te_0.12MnO₃(LTMO)/Si异质结,该异质结具有光生伏特效应和良好的整流特性.光生电压在394 μs的时间内很快增加到最大值然后逐渐减小.在T=80 K时,光生电压的最大值大约是13.7 mV.随着温度的升高,热涨落致使光生电压最大值总体呈现减小趋势,而且是非线性减小,这主要是由LTMO层发生金属绝缘体转变而导致的LTMO层能带结构的变化引起的. 关键词： 异质结 光生伏特效应 电子掺杂