柞蚕丝素／纳米TiO2复合膜的制备及其结构表征

为了获得良好性能的柞蚕丝素复合膜,本文采用复合法制备了不同配比柞蚕丝素/纳米TiO2复合膜,并与纯的丝素膜作了比较,用SEM、DSC、TG和IR进行了表征.SEM测试表明在分散剂聚乙烯醇作用下,适量的纳米TiO2能均匀分散丝素溶液中.DSC测试表明复合膜b、c和d的Tm均高于纯的柞蚕丝素膜a的Tm,然而随着纳米TiO2加入量的继续增加,对应复合膜的Tm有所降低.TG结果表明,随着纳米TiO2加入量的增加,复合膜的热稳定性得到提高.IR测试表明丝素复合膜的结晶结构从Silk I向SilkII转化.     

丝素蛋白/TiO2复合催化剂的制备及其可见光催化性能

通过溶胶-凝胶法制备了不同掺杂量的丝素蛋白/TiO2复合纳米材料,并研究了其可见光催化活性.用粒度分析、X射线衍射(XRD)、紫外-可见漫反射光谱(UV-Vis-DRS)、平带电位、Zeta-电位、元素分析等方法表征了所制备的催化剂样品.结果显示,在可见光照射下,反应2 h时,丝素蛋白/TiO2-400℃的Cr(VI)光催化还原效率达36%,甲酸降解效率达3.4%;相对纯TiO2,丝素蛋白/TiO2的可见光吸收能力均有提高,以丝素蛋白/TiO2-400℃的增幅最大;相对纯TiO2,丝素蛋白/TiO2的平带电位均有不同程度负移,这意味着光生电子有了更强的还原能力;TiO2-400℃、素蛋白/TiO2-300℃、丝素蛋白/TiO2-400℃、丝素蛋白/TiO2-500℃的Zeta-电位值分别为29、31、36、33 mV,说明丝素蛋白/TiO2-400℃在水中形成的溶胶系统分散程度最高.     

纳米TiO2对丝素蛋白膜构象转变的影响

采用溶胶-凝胶法制备纳米TiO2复合丝素膜,并用原子力显微镜、一维红外光谱、二维红外相关光谱对纯丝素膜及复合丝素膜进行了研究。结果表明:纳米TiO2均匀地分散在丝素膜中;纳米粒子与丝素形成了分子间氢键,导致丝素分子的重排;丝素分子链的构象发生了转变,变化顺序是无规线团先于β-折叠、α-螺旋的形成。     

Ti基纳米TiO_2-CNT-Pt复合电极制备、表征及电化学性能

以电合成前驱体Ti(OEt)4直接水解法和电化学扫描电沉积法制备Ti基纳米TiO2-CNT-Pt(Ti/nanoTiO2-CNT-Pt)复合电极.透射电镜(TEM)和X射线衍射(XRD)测试表明,锐钛矿型纳米TiO2粒子(粒径5～10nm)和碳纳米管(CNT)结合形成网状结构,Pt纳米粒子(平均粒径9nm)均匀地分散在纳米TiO2-CNT复合膜表面.循环伏安及计时电流测试表明,Ti/nanoTiO2-CNT-Pt复合电极具有高活性表面,对甲醇的电化学氧化具有高催化活性和稳定性,Pt载量为0.32mg/cm2时,常温常压下甲醇氧化峰电流达到480mA/cm2.     

TiO_2纳米棒和CdSe纳米棒复合膜与聚3-甲基噻吩杂化太阳能电池研究

采用水热法制备了TiO2和CdSe两种纳米棒材料,将两种纳米材料制备成TiO2/CdSe复合纳米棒膜电极,并在复合膜上电化学聚合生成聚3-甲基噻吩poly(3-methylthiophene)(PMeT),研究了其光电化学性能.实验表明,当TiO2与CdSe的物质的量复合比为2:1,PMeT的聚合时间为40s,在电极电势为-0.2V下ITO/TiO2/CdSe/PMeT电极光电转换效率(IPCE)达到56%,对比ITO/TiO2/CdSe复合膜电极在长波方向的光电转换效率明显提高,光吸收截止波长发生了明显的红移.同时以ITO/TiO2/CdSe/PMeT组装了简易的杂化太阳电池,初步研究了光电池性能,光电池总效率为0.08%,Voc=0.4V,jsc=0.61mA/cm2,ff=0.33.     

CNT/Fe-Ni/TiO_2/ZnO阵列修饰Ni阳极的制备及光催化制氢性能

采用层层自组装方法在Ni片阳极上构建TiO2/Zn O纳米棒阵列,以二氧化钛前驱体溶胶中掺杂的铁和镍为催化剂,通过气相沉积法在TiO2/Zn O纳米棒阵列间原位生长碳纳米管(CNTs),得到CNT/Fe-Ni/TiO2/Zn O复合光催化剂修饰的光活性Ni片阳极.以碱性电解池为基础,用紫外线辐照修饰的Ni阳极实现光催化和电解水的有机耦合制氢过程.通过场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、拉曼光谱(Raman)和电化学阻抗谱(EIS)对CNT/Fe-Ni/TiO2/Zn O复合膜光催化剂的结构进行了表征,并测试了其光催化辅助电解水制氢(WEAP)活性.结果表明,生长了碳纳米管的光催化复合膜CNT/Fe-Ni/TiO2/Zn O修饰的Ni阳极的产氢速率分别比Fe-Ni/TiO2/Zn O修饰的Ni阳极和纯Ni片提高了93.7%和533.0%.     

TiO_2/PtO-Pt复合膜和SnO_2/PtO-Pt复合膜氢敏性能的研究

将PtO Pt纳米粒子膜与TiO2 ,SnO2 纳米粒子膜复合 ,利用PtO Pt纳米粒子膜作为插入电极和催化剂 ,设计并研制出一类新型双层结构复合膜气体传感器 .采用TEM和SEM对薄膜的显微结构进行了表征 .对空气中 4 0 %H2 的氢敏性能研究表明 :2 0 0℃时 ,TiO2 /PtO Pt复合膜对氢气的灵敏度为 70 % ,而TiO2 纳米粒子膜无响应 .10 0℃时 ,SnO2 /PtO Pt复合膜的灵敏度为 92 % ,同样条件下 ,SnO2 纳米粒子膜的灵敏度仅为 4% .说明PtO Pt纳米粒子膜的催化作用能够显著提高TiO2 和SnO2 膜的氢敏性能 .另外 ,TiO2 /PtO Pt复合膜和SnO2 /PtO Pt复合膜均对空气中H2 有很高的选择性     

TiO2/PtO-Pt复合膜和SnO2/PtO-Pt复合膜氢敏性能的研究

将PtO-Pt纳米粒子膜与TiO2，SnO2纳米粒子膜复合，利用PtO-Pt纳米粒子膜作 为插入电极和催化剂，设计并研制出一类新型双层结构复合膜气体传感器。采用 TEM和SEM对薄膜的显微结构进行了表征，对空气中4.0H2的氢敏性能研究表明： 200℃时，TiO2/PtO-Pt复合膜对氢气的灵敏度为70％，而TiO2纳米粒子膜无响应。 100℃时，SnO2/PtO-Pt复合膜的灵敏度为92％，同样条件下，SnO2纳米粒子膜的灵 敏度仅为4％。说明PtO-Pt纳米粒子膜的催化作用能够显著提高TiO2和SnO2的膜氢 敏性能。另外，TiO2/PtO-Pt复合膜和SnO2/PtO-Pt复合膜均对空气中H2有很高的选 择性。     

纳米TiO_2改性蚕丝丝素蛋白膜的研究

用溶胶凝胶法制备纳米TiO2改性再生蚕丝丝素蛋白膜.该丝素膜机械强度提高,在水中溶失率下降.UV、AFM、SEM测试的结果表明,丝素中纳米TiO2粒径约为80 nm,纳米粒子在丝素膜中分布均匀;XRD、FTIR测试结果表明,纳米TiO2的加入,可使改性丝素膜的结晶结构从SilkⅠ向SilkⅡ转化,其结晶度也随之提高;TGA测试表明改性丝素膜的热转变温度比纯丝素膜有所改变.     

Zn│纳米TiO2-聚苯胺二次电池的充放电性能

以 1 0mol/L硫酸为介质 ,于 0 8V恒电位下 ,在纳米TiO2 (Nano TiO2 )膜电极上实现了苯胺 (Aniline)的电化学聚合 ,借助透射电镜、X射线衍射、红外光谱等对制得的Nano TiO2 /聚苯胺 (Nano TiO2 /PANI)复合膜进行了表征。用Nano TiO2 │PANI作为二次电池的正极 ,Zn为负极 ,在不同的电流密度下对Zn│Nano TiO2 PANI二次电池的充放电性能进行了研究。结果表明 ,二次电池首次充电容量可达 98 0 4mA·h/g ,充放电效率为 91 6 7% ,充放电曲线平稳     

THE PREPARATION AND STUDY ON THE NANO-TiO_2/SILK FIBROIN COMPOSITE FILMS BY THE SOL-GEL METHOD

1. INTRODUCTIONSilk is a well described natural fiber produced by the silkworm, B. mori, which has been used traditionally in the form of thread in textiles for thousands of years. This silk contains a fibrous protein that forms the thread core and glueli…     

THE PREPARATION AND STUDY ON THE NANO-TiO2/SILK FIBROIN COMPOSITE FILMS BY THE SOL-GEL METHOD

Based on the sol-gel technique using butyl titanate as oxide precursor, the regenerated SF (silk fibroin)/nano-TiO2 composite films were synthesized. Different amounts of butyl titanate to SF were used to verify this effect on the characteristics of the formed materials. Samples were characterized by thermogravimetric analysis, X-ray diffractometry, UV, AFM and FT-IR spectroscopy.The experimental results reveal that, compared to the pure silk fibroin films, the mechanical strength of these regenerated SF/nano-TiO2 composite films were increased and the dissolubility in water of SF/nano-TiO2 composite films in aqueous solution were decreased. The diameter of nano-TiO2 particle films was about 80nm through UV and AFM. The nano-TiO2 particles were well dispersed in the regenerated silk fibroin. It was found that the crystal structures of the composite films were transited from typical Silk Ⅰ to typical Silk Ⅱ by the XRD and FTIR. Furthermore, the crystallinity of the composite films was obviously improved. Through the TGA, it was demonstrated that the heat transition temperature of composite films was also enhanced.     

溶胶-凝胶法制备纳米TiO2/丝素复合膜及结构性能研究

用溶胶凝胶法制备不同比例纳米TiO₂改性再生蚕丝丝素蛋白复合膜. UV和AFM测试结果表明, 该丝素膜中纳米TiO₂均匀分散在丝素中, TiO₂粒径约为80 nm; 同时该丝素膜的结构和热性能用FTIR, XRD, EDS, TGA和DTG进行表征. XRD测试结果表明, 随着纳米TiO₂的加入, 复合丝素膜的结晶结构从Silk I向Silk II转化, 但当纳米TiO₂的加入超过一定量时, 又破坏复合丝素膜的结晶结构; FTIR和EDS测试结果表明, TiO₂与丝素形成较好的键合; TGA和DTG测试表明复合丝素膜的热转变温度相比于纯丝素膜有所提高.     

丝素蛋白膜上5-氟尿嘧啶的包埋及其释放

讨论了包埋在丝素膜中的５－氟脲嘧啶（５－ＦＵ）的固定状况,在不同ＰＨ值下测定了丝素５－ＦＵ复合膜中药物的释放,实验结果表明：５－ＦＵ均匀地被包埋在丝素膜中,即丝素膜可以作为５－ＦＵ载体,经过比涂层保护,丝素５－ＦＵ复合膜中的５－ＦＵ溶解释放速率变慢,释放时间延长;经涂层的 素５－ＦＵ复合膜在接近丝素蛋白等电点（ＰＨ＝４．５）时,５－ＦＵ在溶液中释放速度较慢,释放时间较长,表明用调节外部溶液ＰＨ值的     

蚕丝蛋白与硅溶胶复合材料的研究

采用动态力学测试手段(DMA)并结合扫描电镜和拉曼光谱等方法,考察了用桑蚕丝蛋白与二氧化硅水分散体系(硅溶胶)制备的复合材料的结构与性质.结果表明,在此共混体系中,直径约为100 nm的二氧化硅聚集体与丝蛋白连续相的界面相容性良好.动态力学测试发现,复合材料的动态力学性能在15℃到55℃范围相对于纯丝蛋白材料得到了改善,二氧化硅组分的加入对丝蛋白分子链段的运动性有所阻碍,从而导致了40℃模量损耗的消失.     

原位化学氧化聚合制备聚苯胺/丝素复合导电膜

采用原位化学氧化聚合方法在蚕丝丝素蛋白膜表面生长聚苯胺,制备得到表面均匀覆盖导电聚合物的复合导电丝素膜,其电导率约为3×10^-2S/cm。纤维表面与导电聚合物的相互作用改善了原丝素膜的耐热性能,但并未降低其力学性能。     

QUENCHING OF PHOTOEXCITED 4,4'-DICARBOXY-2,2'-BIPYRIDINEBIS(2,2'-BIPYRIDINE)RUTHENIUM(II) BY OXYGEN IN AQUEOUS SOLUTION AND IN SILK FIBROIN MEMBRANE

Abstract— Photoluminescence and quenching of 4,4'-dicarboxy-2,2'-bipyridinebis(2,2'-bipyridine)-ruthenium(II) complex (Ru(DCbpy)(bpy)²₂⁺) in an aqueous solution as well as in a silk fibroin membrane were studied. Emission quenching by oxygen in an aqueous solution showed a linear relationship with respect to oxygen concentration. When the complex was incorporated into a silk fibroin membrane by adsorption from an aqueous solution into a preformed membrane, the photoexcited state of the complex was not quenched by oxygen in an aqueous phase. However, when the complex was incorporated into a silk fibroin membrane by casting a mixture of the complex and silk fibroin, the photoexcited complex was quenched by oxygen in an aqueous phase. In this case the Stern-Volmer plots showed a downward-deviating curve indicating heterogeneity of the probe site. Emission intensity decreased with an increase of the water content in the silk fibroin membrane.     

蚕丝纤维/丝蛋白复合材料力学性能的优化

在制备具有良好力学性能的蚕丝纤维/丝蛋白复合材料的基础上,采用力学测试、扫描电镜以及广角X-射线衍射等手段,考察了溴化锂预处理和甲醇后处理这两种方法对蚕丝纤维/丝蛋白界面性能的影响.力学测试的结果表明,在相同纤维含量(如20 wt％)的情况下,采用6 mol L-1溴化锂对定向排列的蚕丝纤维预处理10 min,所得的蚕...     

Fabrication and features of a Methylene Green-mediating sensor for hydrogen peroxide based on regenerated silk fibroin as immobilization matrix for peroxidase

Regenerated silk fibroin prepared from waste silk was employed as immobilization matrix for peroxidase and the structures of the blend membranes of regenerated silk fibroin and peroxidase were first investigated with IR and scanning electron microscopy. There was intermolecular interaction between peroxidase and regenerated silk fibroin in the immiscible state. Cyclic voltammetry and constant applied potential measurement showed that Methylene Green efficiently mediated electron transfer from oxidized horseradish peroxidase in regenerated silk fibroin membrane to a glassy carbon electrode. A sensor coupling immobilized peroxidase with Methylene Green responded rapidly to low H(2)O(2) concentration and achieved 95% of the steady-state current in less than 25 s with a detection limit of 1.0 x 10(-7) M H(2)O(2). The sensor was stable in continuous operation, indicating that peroxidase was entrapped in regenerated silk fibroin membrane and did not freely diffuse away from the sensor surface into solutions.