A 2.4GHz CMOS Monolithic Transceiver Front-End for IEEE 802.11b Wireless LAN Applications

A 2.4GHz CMOS monolithic transceiver front-end for IEEE 802.11b wireless LAN applications is presented.The receiver and transmitter are both of superheterodyne structure for good system performance.The front-end consists of five blocks:low noise amplifier,down-converter,up-converter, pre-amplifier,and LO buffer.Their input/output impedance are all on-chip matched to 50Ω except the down-converter which has open-drain outputs.The transceiver RF front-end has been implemented in a 0.18μm CMOS process.When the LNA and the down-converter are directly connected,the measured noise figure is 5.2dB,the measured available power gain 12.5dB,the input 1dB compression point -18dBm,and the third-order input intercept point -7dBm.The receiver front-end draws 13.6mA currents from the 1.8V power supply.When the up-converter and pre-amplifier are directly connected,the measured noise figure is 12.4dB,the power gain is 23.8dB,the output 1dB compression point is 15dBm,and the third-order output intercept point is 16dBm.The transmitter consumes 276mA current from the 1.8V power supply.     

应用于IEEE 802.11b无线局域网系统的2.4GHzCMOS单片收发机射频前端

实现了一个应用于IEEE 802.11b无线局域网系统的2.4GHz CMOS单片收发机射频前端,它的接收机和发射机都采用了性能优良的超外差结构.该射频前端由五个模块组成:低噪声放大器、下变频器、上变频器、末前级和LO缓冲器.除了下变频器的输出采用了开漏级输出外,各模块的输入、输出端都在片匹配到50Ω.该射频前端已经采用0.18μm CMOS工艺实现.当低噪声放大器和下变频器直接级联时,测量到的噪声系数约为5.2dB,功率增益为12.5dB,输入1dB压缩点约为-18dBm,输入三阶交调点约为-7dBm.当上变频器和末前级直接级联时,测量到的噪声系数约为12.4dB,功率增益约为23.8dB,输出1dB压缩点约为1.5dBm,输出三阶交调点约为16dBm.接收机射频前端和发射机射频前端都采用1.8V电源,消耗的电流分别为13.6和27.6mA.     

A 0.13 μm CMOS UWB RF Transmitter with an On‐Chip T/R Switch

This paper presents a fully integrated 0.13 μm CMOS MB‐OFDM UWB transmitter chain (mode 1). The proposed transmitter consists of a low‐pass filter, a variable gain amplifier, a voltage‐to‐current converter, an I/Q up‐mixer, a differential‐to‐single‐ended converter, a driver amplifier, and a transmit/receive (T/R) switch. The proposed T/R switch shows an insertion loss of less than 1.5 dB and a Tx/Rx port isolation of more than 27 dB over a 3 GHz to 5 GHz frequency range. All RF/analog circuits have been designed to achieve high linearity and wide bandwidth. The proposed transmitter is implemented using IBM 0.13 μm CMOS technology. The fabricated transmitter shows a ?3 dB bandwidth of 550 MHz at each sub‐band center frequency with gain flatness less than 1.5 dB. It also shows a power gain of 0.5 dB, a maximum output power level of 0 dBm, and output IP3 of +9.3 dBm. It consumes a total of 54 mA from a 1.5 V supply.     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below-8.5 dB across the 3.1-4.7 GHz frequency range, max-imum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of-11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm2.     

A CMOS Frequency Synthesizer Block for MB‐OFDM UWB Systems

A CMOS frequency synthesizer block for multi‐band orthogonal frequency division multiplexing ultra‐wideband systems is proposed. The proposed frequency synthesizer adopts a double‐conversion architecture for simplicity and to mitigate spur suppression requirements for out‐of‐band interferers in 2.4 and 5 GHz bands. Moreover, the frequency synthesizer can consist of the fewest nonlinear components, such as divide‐by‐Ns and a mixer with the proposed frequency plan, leading to the generation of less spurs. To evaluate the feasibility of the proposed idea, the frequency synthesizer block is implemented in 0.18‐µm CMOS technology. The measured sideband suppression ratio is about 32 dBc, and the phase noise is ‐105 dBc/Hz at an offset of 1 MHz. The fabricated chip consumes 17.6 mA from a 1.8 V supply, and the die‐area including pads is 0.9 × 1.1 mm².     

A 6-9 GHz 5-band CMOS synthesizer for MB-OFDM UWB

An ultra-wideband frequency synthesizer is designed to generate carrier frequencies for 5 bands distributed from 6 to 9 GHz with less than 3 ns switching time.It incorporates two phase-locked loops and one single-sideband (SSB) mixer.A 2-to-1 multiplexer with high linearity is proposed.A modified wideband SSB mixer,quadrature VCO, and layout techniques are also employed.The synthesizer is fabricated in a 0.18μm CMOS process and operates at 1.5-1.8 V while consuming 40 mA current.The measured phase noise ...     

一种用于五频带的MB-OFDM超宽带的6至9GHz的CMOS频率综合器

本论文设计了一个超宽带频率综合器。该频率综合器通过采用两个锁相环和一个单边带混频器产生了6至9GHz内的五个频带中心频率,频带之间的跳频时间小于3纳秒。文中提出了一个高线性度的二选一多路选择器,一个宽带的单边带混频器和一个正交压控振荡器。此外,版图也做了一些特殊考虑。该频率综合器采用0.18微米CMOS工艺实现,在1.5V至1.8V电源电压下消耗40mA电流,测试结果显示10MHz频偏处的相位噪声为-128dBc/Hz,在7.656GHz频带处的边带抑制为-22dBc。     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below -8.5 dB across the 3.1-4.7 GHz frequency range, maximum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of -11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm^2.     

一种应用于6-9GHz UWB系统的低噪声CMOS射频前端设计

本文介绍了一种应用于6-9 GHz超宽带系统的全集成差分CMOS射频前端电路设计。在该前端电路中应用了一种电阻负反馈形式的低噪声放大器和IQ两路合并结构的增益可变的折叠式正交混频器。芯片通过TSMC 0.13µm RF CMOS工艺流片,含ESD保护电路。经测试得该前端电路大电压增益为23~26dB,小电压增益为16~19dB;大增益下前端电路平均噪声系数为3.3-4.6dB,小增益下的带内输入三阶交调量(IIP3)为-12.6dBm。在1.2V电压下,消耗的总电流约为17mA。     

A Dual‐Mode 2.4‐GHz CMOS Transceiver for High‐Rate Bluetooth Systems

This paper reports on our development of a dual‐mode transceiver for a CMOS high‐rate Bluetooth system‐on‐chip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front‐end. It is designed for both the normal‐rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high‐rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual‐path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual‐mode system. The transceiver requires none of the external image‐rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order on‐chip filters. The chip is fabricated on a 6.5‐mm² die using a standard 0.25‐μm CMOS technology. Experimental results show an in‐band image‐rejection ratio of 40 dB, an IIP3 of ?5 dBm, and a sensitivity of ?77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive π/4‐diffrential quadrature phase‐shift keying (π/4‐DQPSK) mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5‐V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low‐cost, multi‐mode, high‐speed wireless personal area network.     

3．1～10．6GHz超宽带低噪声放大器的设计

基于SIMC0．18μmRFCMOS工艺技术,设计了可用于3．1—10．6GHzMB—OFDM超宽带接收机射频前端的CMOS低噪声放大器（LNA）。该LNA采用三级结构：第一级是共栅放大器,主要用来进行输入端的匹配;第二级是共源共栅放大器,用来在低频段提供较高的增益;第三级依然为共源共栅结构,用来在高频段提供较高的增益,从而补偿整个频带的增益使得增益平坦度更好。仿真结果表明：在电源电压为1．8v的条件下,所设计的LNA在3．1～10．6GHz的频带范围内增益（521）为20dB左右,具有很好的增益平坦性f±0．4dB）,回波损耗S11、S22均小于-10dB,噪声系数为4．5dB左右,IIP3为-5dBm,PIdB为0dBm。     

A 900 MHz Zero‐IF RF Transceiver for IEEE 802.15.4g SUN OFDM Systems

This paper presents a 900 MHz zero‐IF RF transceiver for IEEE 802.15.4g Smart Utility Networks OFDM systems. The proposed RF transceiver comprises an RF front end, a Tx baseband analog circuit, an Rx baseband analog circuit, and a ΔΣ fractional‐N frequency synthesizer. In the RF front end, re‐use of a matching network reduces the chip size of the RF transceiver. Since a T/Rx switch is implemented only at the input of the low‐noise amplifier, the driver amplifier can deliver its output power to an antenna without any signal loss; thus, leading to a low dc power consumption. The proposed current‐driven passive mixer in Rx and voltage‐mode passive mixer in Tx can mitigate the IQ crosstalk problem, while maintaining 50% duty‐cycle in local oscillator clocks. The overall Rx‐baseband circuits can provide a voltage gain of 70 dB with a 1 dB gain control step. The proposed RF transceiver is implemented in a 0.18 μm CMOS technology and consumes 37 mA in Tx mode and 38 mA in Rx mode from a 1.8 V supply voltage. The fabricated chip shows a Tx average power of ?2 dBm, a sensitivity level of ?103 dBm at 100 Kbps with , an Rx input P_1dB of ?11 dBm, and an Rx input IP3 of ?2.3 dBm.     

Design of 60GHz RF Transceiver in CMOS:Challenges and Recent Advances

With more than 40 years Moore scaling, the speed of CMOS transistors is around 100 GHz. Such fact makes it possible to realize mm-wave circuits in CMOS. However, with the target of achieving broadband and power-efficient operation, 60 GHz CMOS RF transceiver faces severe challenges. After reviewing the technology issues, regarding the 60 GHz applications, this paper discusses design challenges both from the system and the building block levels, and also presents some simulated or measured circuits results.     

Design of a fully differential CMOS LNA for 3.1-10.6 GHz UWB communication systems

A fully differential complementary metal oxide semiconductor （CMOS） low noise amplifier （LNA） for 3.1-10.6 GHz ultra-wideband （UWB） communication systems is presented. The LNA adopts capacitive cross-coupling common-gate （CG） topology to achieve wideband input matching and low noise figure （NF）. Inductive series-peaking is used for the LNA to obtain broadband flat gain in the whole 3.1-10.6 GHz band. Designed in 0.18 um CMOS technology, the LNA achieves an NF of 3.1-4.7 dB, an Sll of less than -10 dB, an S21 of 10.3 dB with ±0.4 dB fluctuation, and an input 3rd interception point （IIP3） of -5.1 dBm, while the current consumption is only 4.8 mA from a 1.8 V power supply. The chip area of the LNA is 1×0.94 mm^2.     

A 3.1-4.8 GHz CMOS receiver for MB-OFDM UWB

An integrated fully differential ultra-wideband CMOS receiver for 3.1-4.8 GHz MB-OFDM systems is presented. A gain controllable low noise amplifier and a merged quadrature mixer are integrated as the RF front-end. Five order Gm-C type low pass filters and VGAs are also integrated for both I and Q IF paths in the receiver. The ESD protected chip is fabricated in a Jazz 0.18 μm RF CMOS process and achieves a maximum total voltage gain of 65 dB, an AGC range of 45 dB with about 6 dB/step, an averaged total noise figure of 6.4 to 8.8 dB over 3 bands and an in-band lIP3 of-5.1 dBm. The receiver occupies 2.3 mm2 and consumes 110 mA from a 1.8 V supply including test buffers and a digital module.     

一种用于3.1–4.8GHz MB-OFDM 超宽带系统的CMOS接收机

本文介绍一种应用于3.1-4.8GHz 多频带正交频分复用超宽带系统的全集成全差分CMOS接收机芯片。在接收机射频前端中应用了一种增益可变的低噪声放大器和合并结构的正交混频器。在I/Q中频通路中则集成了5阶Gm-C结构的有源低通滤波器以及可变增益放大器。芯片通过Jazz 0.18μm RF CMOS工艺流片,含ESD保护电路。该接收机最大电压增益为65dB,增益可调范围为45dB,步长6dB;接收机在3个频段的平均噪声系数为6.4-8.8dB,带内输入三阶交调量(IIP3)为-5.1dBm。芯片面积为2.3平方毫米,在1.8V电压下,包括测试缓冲电路和数字模块在内的总电流为110mA。     

A 3.1-4.8 GHz CMOS receiver for MB-OFDM UWB

An integrated fully differential ultra-wideband CMOS receiver for 3.1-4.8 GHz MB-OFDM systems is presented. A gain controllable low noise amplifier and a merged quadrature mixer are integrated as the RF front-end. Five order Gm-C type low pass filters and VGAs are also integrated for both I and Q IF paths in the receiver. The ESD protected chip is fabricated in a Jazz 0.18μm RF CMOS process and achieves a maximum total voltage gain of 65 dB, an AGC range of 45 dB with about 6 dB/step, an averaged total noise figure of 6.4 to 8.8 dB over 3 bands and an in-band IIP3 of-5.1 dBm. The receiver occupies 2.3 mm2 and consumes 110 mA from a 1.8 V supply including test buffers and a digital module.     

CMOS全差分超宽带低噪声放大器

文中给出了一个应用于超宽带射频接收机中的全集成低噪声放大器,该低噪声放大器采用了电阻并联负反馈与源极退化电感技术的结合,为全差分结构,在Jazz0.18μm RF CMOS工艺下实现,芯片面积为1.08mm2,射频端ESD抗击穿电压为1.4kV。测试结果表明,在1.8V电源电压下,该LNA的工作频带为3.1～4.7GHz,功耗为14.9mW,噪声系数(NF)为1.91～3.24dB,输入三阶交调量(IIP3)为-8dBm。     

3～5 GHz超宽带无电感CMOS低噪声放大器设计

基于TSMC O.18μm RFCMOS工艺设计了一种无电感并联负反馈的超宽带低噪声放大器(LNA).在3～5 GHz工作频率范围内,电阻电流复用技术为整体电路提供自偏置,使其在足够的带宽范围内均可实现较高增益;同时噪声相消技术又可消除部分沟道热噪声,在很大程度上降低了放大器的噪声系数,由仿真结果可以看到:LNA在3～5 GHz内实现了良好输入输出匹配和较好的线性度,同时得到了较好的电压增益和噪声性能;并且其在整个频带范围内增益达到11～13.9 dB,噪声系数小于4.6 dB.整个设计最大的优点是没有用到片上电感,使得芯片面积大大缩小,这对商业应用具有极大的吸引力。     

A CMOS Word Alignment Configurable Transceiver for Multi-Standard Fiber Communication Systems

This paper describes a configurable transceiver which can realize multiple operation modes to meet various fiber communication standards. With this configurable architecture, the transceiver can operate in 2：1, 3：1, 4：1, 5：1, 6：1, 8：1, 10：1 multiplexing modes and 1：2, 1：3, 1：4, 1：5, 1：6, 1：8, 1：10 demultiplexing modes with internal synchronized clock signals. Comma detection and word alignment circuits are also included in the receiver to meet the standards using 8B/10B code. This configurable multi-mode transceiver has been implemented in a 0.25μm CMOS technology.