Stepwise annealing of poly(butylene terephthalate)

Annealing of poly(butylene terephthalate) (PBT) was studied by differential scanning calorimetry (DSC) and small angle X‐ray scattering (SAXS) measurement. A PBT sample was annealed at a recrystallization temperature where recrystallization occurs with a maximum rate in the heating process of the sample. In the subsequent annealing steps, the annealed sample was annealed repeatedly at the recrystallization temperatures, and the stepwise annealing sample was obtained. Peak melting temperature (T_m) and sharpness of DSC peak of the stepwise annealing sample increased with the annealing step. A high melting‐temperature sample was obtained in a short time, and T_m increased up to 238.5°C which is higher than all the T_m values that appear in the literature. The long period calculated from SAXS curves of the stepwise annealing sample increased with the annealing step. The increase of crystallite size and perfection of the crystal in the stepwise annealing process is suggested. Annealing experiment indicated that T^°_m should be higher than about 235°C. T_m increased linearly with the annealing temperature of the final step in the stepwise annealing (T_a). The equilibrium melting temperature (T^°_m) for PBT was estimated to be 247°C by the application of a Hoffman–Weeks plot to the relation between T_m vs. T_a. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2420–2429, 1999     

Multiple melting behavior of poly(butylene succinate). II. Thermal analysis of isothermal crystallization and melting process

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights (MWs) of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were isothermally crystallized at various crystallization temperatures (T_c) ranging from 70 to 97.5 °C. The T_c dependence of crystallization half‐time (τ) was obtained. DSC melting curves for the isothermally crystallized samples were obtained at a heating rate of 10 K min⁻¹. Three endothermic peaks, an annealing peak, a low‐temperature peak L, and a high‐temperature peak H, and an exothermic peak located between peaks L and H clearly appeared in the DSC curve. In addition, an endothermic small peak S appeared at a lower temperature of peak H. Peak L increased with increasing T_c, whereas peak H decreased. The T_c dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of T_c. T_m(L), T_re, and ΔH increased almost linearly with T_c, whereas T_m(H) was almost constant. The maximum rate of recrystallization occurred immediately after the melting. The mechanism of the multiple melting behavior is explained by the melt‐recrystallization model. The high MW samples showed similar T_c dependence of τ, and τ for the lowest MW sample was longer than that for the others. Peak L increased with MW, whereas peak H decreased. In spite of the difference of MW, T_m(L), T_m(H), and T_re almost coincided with each other at the same T_c. The ΔH values, that is crystallinity, for the highest MW sample were smaller than those for the other samples at the same T_c. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2039–2047, 2005     

Multiple melting behavior of poly(butylene succinate). I. Thermal analysis of melt‐crystallized samples

The multiple melting behavior of poly(butylene succinate) (PBSu) was studied with differential scanning calorimetry (DSC). Three different PBSu resins, with molecular weights of 1.1 × 10⁵, 1.8 × 10⁵, and 2.5 × 10⁵, were cooled from the melt (150 °C) at various cooling rates (CRs) ranging from 0.2 to 50 K min^?1. The peak crystallization temperature (T_c) of the DSC curve in the cooling process decreased almost linearly with the logarithm of the CR. DSC melting curves for the melt‐crystallized samples were obtained at 10 K min^?1. Double endothermic peaks, a high‐temperature peak H and a low‐temperature peak L, and an exothermic peak located between them appeared. Peak L decreased with increasing CR, whereas peak H increased. An endothermic shoulder peak appeared at the lower temperature of peak H. The CR dependence of the peak melting temperatures [T_m(L) and T_m(H)], recrystallization temperature (T_re), and heat of fusion (ΔH) was obtained. Their fitting curves were obtained as functions of log(CR). T_m(L), T_re, and ΔH decreased almost linearly with log(CR), whereas T_m(H) was almost constant. Peak H decreased with the molecular weight, whereas peak L increased. It was suggested that the rate of the recrystallization decreased with the molecular weight. T_m(L), T_m(H), T_re, and T_c for the lowest molecular weight sample were lower than those for the others. In contrast, ΔH for the highest molecular weight sample was lower than that for the others. If the molecular weight dependence of the melting temperature for PBSu is similar to that for polyethylene, the results for the molecular weight dependence of PBSu can be explained. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2411–2420, 2002     

Thermodynamic and kinetic behaviour of salicylsalicylic acid

The thermal behaviour of salicylsalicylic acid (CAS number 552-94-3) was studied by differential scanning calorimetry (DSC). The endothermic melting peak and the fingerprint of the glass transition were characterised at a heating rate of 10°C min^-1. The melting peak showed an onset at T _on = 144°C (417 K) and a maximum intensity at T _max = 152°C (425 K), while the onset of the glass transition signal was at T _on = 6°C. The melting enthalpy was found to be Δ_mH = 28.9±0.3 kJ mol^-1, and the heat capacity jump at the glass transition was ΔC _P = 108.1±0.1 J K^-1mol^-1. The study of the influence of the heating rate on the temperature location of the glass transition signal by DSC, allowed the determination of the activation energy at the glass transition temperature (245 kJ mol^-1), and the calculation of the fragility index of salicyl salicylate (m = 45). Finally, the standard molar enthalpy of formation of crystalline monoclinic salicylsalicylic acid at T = 298.15 K, was determined as Δ_fH_m ^o(C₁₄H₁₀O₅, cr) = - (837.6±3.3) kJ mol^-1, by combustion calorimetry. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermal behavior of polytriazole films: A thermal analysis study

The thermal behavior of poly(1,3-phenyl-1,4-phenyl)-4-phenyl-1,2,4-triazole has been investigated using different scanning calorimetry (DSC) and thermogravimetry (TG). Processes are studied for this thermally stable polymer that take place between 200 and 500°C. While the polycondensation reaction product in powder from appeared to be partially crystalline, films prepared by casting from a formic acid solution appeared to be completely amorphous. A thermal treatment between T_g(～ 270°C) and T_m(～ 430°C) can introduce crystallinity in the films because of the polymer's ability to cold crystallize. The cold crystallization temperature T_c seems to be dependent on the preparation history of the solid polymer phase. Thermal annealing of the films just below T_g does not introduce crystallinity but inhibits subsequent cold crystallization at higher temperatures. Crystallization upon cooling from the crystalline melt has not been observed either. At temperatures just above the crystalline melting point the polymer starts to decompose in an exothermic reaction.     

Thermostability of rat sarcoma M1 procollagen solutions,procollagen fibers and whole tissues

In close to equilibrium conditions (1° per 400 min), the DSC measurements demonstrated that the melting parameters of white rat sarcoma M1 procollagen equaled to T_m?=?34.4 °C and ΔT_m?=?2.7°, and the same parameters of fibers reconstructed from those solutions of procollagen were T_m?=?38.5 °C and ΔT?=?3.1°. These values were by 1.0° lower and 0.8° wider, and by 1.7° lower and 0.7° wider in comparison with the parameters of procollagen and fibers of healthy rat tissue, accordingly. The simultaneous increase in melting temperature and melting width, and a weak decrease in melting enthalpy demonstrated that sarcoma M1 procollagen had some defects. The considerable decrease by 7° in melting temperature and decrease in thermostability of procollagen fibrils in case of sarcoma M1 in comparison to the healthy norm gives a good prospective potential of using this approach as a quick DSC test to detect various sarcomas, including human sarcomas, by comparing the biopsy material or postsurgical tissues with the normal samples.

     

Thermal analysis of the double-melting behavior of poly(L-lactic acid)

The melting and crystallization behavior of poly(L -lactic acid) (PLLA; weight-average molecular weight = 3 × 10⁵) was studied with differential scanning calorimetry (DSC). DSC curves for PLLA samples were obtained at various cooling rates (CRs) from the melt (210 °C). The peak crystallization temperature and the exothermic heat of crystallization determined from the DSC curve decreased almost linearly with increasing log(CR). DSC melting curves for the melt-crystallized samples were obtained at various heating rates (HRs). The double-melting behavior was confirmed by the double endothermic peaks, a high-temperature peak (H) and a low-temperature peak (L), that appeared in the DSC curves at slow HRs for the samples prepared with a slow CR. Peak L increased with increasing HR, whereas peak H decreased. The peak melting temperatures of L and H [T_m(L) and T_m(H)] decreased linearly with log(HR). The appearance region of the double-melting peaks (L and H) was illustrated in a CR–HR map. Peak L decreased with increasing CR, whereas peak H increased. T_m(L) and T_m(H) decreased almost linearly with log(CR). The characteristics of the crystallization and double-melting behavior were explained by the slow rates of crystallization and recrystallization, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 25–32, 2004     

Self-nucleation and recrystallization of isotactic polypropylene (α phase) investigated by differential scanning calorimetry

The crystallization behavior after partial or complete melting of the α phase of iPP is examined by combined differential scanning calorimetry (DSC) and optical microscopy: calorimetric results are directly correlated with corresponding morphologies of microtome sections of DSC samples. On partial melting at various temperatures (hereafter referred to as T_s) located in a narrow range (4°C) below and near T_m, the number of nuclei increases (as in classical self-nucleation experiments), by several orders of magnitude; on subsequent cooling, the crystallization peak is shifted by up to 25°C. After partial melting in the lower part of the T_s range and recrystallization, the polymers display a prominent morphology “memory effect” whereby a phantom pattern of the initial spherulite morphology is maintained. After partial melting in the upper part of the T_s range the initial morphology is erased and self-nucleation affects only the total number of nuclei. The present experimental procedures make it possible to define, under “standard” conditions, the crystallization range of the polymer and in particular, the maximum crystallization temperature achievable when “ideally” nucleated. © John Wiley & Sons, Inc.     

On the origin of the multiple melting behavior in poly(ethylene naphthalene‐2,6‐dicarboxylate): Microstructural study as revealed by differential scanning calorimetry and X‐ray scattering

In this article a study on the melting behavior and microstructure of semicrystalline poly(ethylene naphthalene‐2,6‐dicarboxylate) (PEN) prepared by crystallization from the glass under different annealing conditions is presented. The influence of the annealing temperature (T_a), annealing time (t_a), and the heating rate (R_h) at which T_a is reached on the endothermic behavior of the samples was investigated by means of differential scanning calorimetry (DSC). A dual melting behavior appeared for low R_h values (2 deg · min⁻¹) within the range of 145 °C < T_a < 250 °C and 1 min ≤ t_a. ≤ 16 h. Samples subjected to fast heating rates (R_h = 200 deg · min⁻¹) to reach a T_a ≥ 230 °C showed DSC traces in which a transition is observed from three peaks to a single melting peak when t_a increases in the 30–240 min range. On the basis of the DSC results, PEN samples were prepared displaying single or dual endothermic behavior. The microstructure of these samples was studied by wide (WAXS) and small‐angle X‐Ray scattering (SAXS) techniques. The SAXS data were analyzed using the correlation function and interface distribution function formalisms, respectively. In samples with a single melting behavior, microstructural parameters such as the long spacing, the amorphous and the crystalline phase thicknesses are consistent with a lamellar stacking model in which the thickness distributions of both phases are almost the same. For samples exhibiting two melting endotherms, a dual lamellar model, which is in agreement with the experimental results is proposed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1167–1182, 2000     

Solid-state relaxations in poly(ethylene oxide). I. Study using the differential scanning calorimetry method

Differential scanning calorimetry (DSC) studies show that poly(ethylene oxide) (PEO) exhibits three transition regions below its melting point. The effects of annealing on the intensity and temperature of these transitions enable us to locate T < T_g (T_γ) T_g, and T_α at about 130–140. 190–240, and 263–313°K, respectively. Our results argue for a small transition T_g (L) at 190–200°K with a second T_g (U) above 233°K, the temperature of which increases on annealing. The shape of DSC derivative curves reveals that T < T_g and T_α are complex and suggests the possibility of two steps in these processes. In addition, a splitting of T_α is observed every time a multiple melting endotherm appears as a result of annealing. Up to three separate melting endotherms can be observed. One of them is related to the normal primary crystallization process. Its peak temperature increases linearly with the annealing temperature, yielding an extrapolated value for the equilibrium melting temperature T of 347°K as found before.     

Thermal stability and nonisothermal crystallization of short fiber-reinforced poly(ether ether ketone) composites

The thermal stability of a short carbon-fiber-reinforced PEEK composite was assessed by thermogravimetry and by a Rheometrics dynamic analyzer. The results indicated that holding for 10 min at 380°C was a suitable melting condition to avoid the thermooxidative degradation under air. After proving that the heating rate of 50°C/min can be used to evaluate the crystallinity, a heating stage was used to prepare nonisothermally crystallized specimens using cooling rates from 1 to 100°C/min after melting at 400°C for 3 or 15 min. The degree of crystallinity and the melting behavior of these specimens were investigated by DSC at a heating rate of 50°C/min. The presence of three or four regions indicated that the upper melting temperature, T_m, changed with the crystallization temperature. The first region with the highest T_m, which corresponded to the cooling rate of 1°C/min, can be associated with the crystallization in regime II. There was a second region where T_m decreased as the amount of crystals formed in regime II decreased with increasing cooling rate from 5 to 20°C/min. The third region, a plateau region, corresponded to regime III condition in which the crystals were imperfect. In the fourth region, the cooling was so fast that crystallization was incomplete during the cooling for the melting condition of 400°C for 15 min. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2225–2235, 1998     

New insights into the multiple melting behaviors of the semicrystalline ethylene‐hexene copolymer: Origins of quintuple melting peaks

A semicrystalline ethylene‐hexene copolymer (PEH) was subjected to a simple thermal treatment procedure as follows: the sample was isothermally crystallized at a certain isothermal crystallization temperature from melt, and then was quenched in liquid nitrogen. Quintuple melting peaks could be observed in heating scan of the sample by using differential scanning calorimeter (DSC). Particularly, an intriguing endothermic peak (termed as Peak 0) was found to locate at about 45 °C. The multiple melting behaviors for this semicrystalline ethylene‐hexene copolymer were investigated in details by using DSC. Wide‐angle X‐ray diffraction (WAXD) technique was applied to examine the crystal forms to provide complementary information for interpreting the multiple melting behaviors. Convincing results indicated that Peak 0 was due to the melting of crystals formed at room temperature from the much highly branched ethylene sequences. Direct heating scans from isothermal crystallization temperature (T_c, 104–118 °C) were examined for comparison, which indicated that the multiple melting behaviors depended on isothermal crystallization temperature and time. A triple melting behavior could be observed after a relatively short isothermal crystallization time at a low T_c (104–112 °C), which could be attributed to a combination of melting of two coexistent lamellar stack populations with different lamellar thicknesses and the melting‐recrystallization‐remelting (mrr) event. A dual melting behavior could be observed for isothermal crystallization with both a long enough time at a low T_c and a short or long time at an intermediate T_c (114 °C), which was ascribed to two different crystal populations. At a high T_c (116–118 °C), crystallizable ethylene sequences were so few that only one single broad melting peak could be observed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2100–2115, 2008     

Lamellar thickening in nascent poly(acrylonitrile) upon annealing

No systematic study has been reported on the lamellar thickening in atactic poly(acrylonitrile) (PAN) upon annealing because PAN, in the form of solution‐cast films or their drawn products, generally shows no small‐angle X‐ray scattering (SAXS) maximum corresponding to the lamellar thickness. In this work, PAN crystals were precipitated during the thermal polymerization of acrylonitrile in solution. The nascent PAN film, obtained by the filtration of the crystal suspension, exhibited a clear SAXS maximum revealing the lamellar structure. The lamellar thickening upon annealing of the nascent PAN films was studied in the temperature range 100–180 °C, where the degradation was minimal, as confirmed by the absence of an IR absorption band at 1605 cm⁻¹ ascribed to the cyclized nitrile groups. Above 190 °C, the degradation of the samples was significant, and the SAXS became too broad to determine the scattering maximum. The long period was significantly affected by the annealing time (t_a) and the temperature (T_a). Depending on t_a, three stages were observed for the lamellar thickening behavior. The lamellar thickness stayed constant in stage I (t_a = 0.5–3 min, depending on T_a), rapidly increased in stage II (t_a = 0.5–8 min), and stayed at a constant value characteristic for each T_a at yet longer t_a's in stage III. The lamellar thickness characteristic for T_a increased rapidly with increasing T_a at 165 °C (or higher), which was 152 °C lower than the estimated melting temperature of PAN (T_m = 317 °C). A possible mechanism for such lamellar thickening in PAN far below the T_m is discussed on the basis of the enhanced chain mobility in the crystalline phase above the crystal/crystal reversible transition at 165–170 °C detected by differential scanning calorimetry and wide‐angle X‐ray diffraction. The structural changes associated with annealing are also discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2571–2579, 2000     

Thermal analysis and microscopical characterization of cholesterol in gallstones

Summary Cholesterol constitutes the major component of most gallstones. It was identified and determined in gallstones by thermal analysis technique (DSC and TG-DTA), mainly by the use of the melting temperature (T_onset=145°C and T_max=149°C) and by DTG peak decomposition (T_max=364°C). Cholesterol anhydrous (ChA), which showed endothermic polymorphic peak, T_max=40°C, without mass loss, was differentiated from cholesterol monohydrate (ChH), which showed a broad endothermic peak, T_max=59°C, attributed to loss of water of crystallization (theoretical 4.45%). Morphological studies of gallstones were performed by optical microscopy and scanning electron microscopy (SEM). The stones consisted of a pigmented core with a variably-sized irregular central cavity, surrounded by a radially arranged deposits of plate-like ChH. The outer part of the stones showed ChA crystal arborescences. X-ray microanalysis gave a typical spectrum rich in C and O, and in some instances the presence of P, which was attributed to the presence of phospholipids. CaCO₃ was easily characterized by TG with the use of DTG decomposition peak at 674°C.     

Glass Transition Temperature Improvement for Polychloroprene by One-Step ATRP Reaction

Polymethyl methacrylate (PMMA) polymer chains were grafted on neoprene W (NW) by a one-step ATRP reaction. The thermal properties of the products were analyzed by DSC. Improvement of T _g was a result of the PMMA grafted chains. Also, the melting point (T _m ) changed from 42°C for NW to 142°C for modified NW. Using different solvents for the resulting copolymers, aggregates were obtained. Phase separation was influenced by the grafting degree of PMMA and the employed solvent. The copolymers were analyzed by GPC, FT-IR, DSC, and SEM.     

Changes of mechanical properties in cold-crystallized syndiotactic polypropylene during aging

Many semicrystalline polymers undergo a process of aging when they are stored at temperatures higher than their glass-transition temperature (T _g). Syndiotactic polypropylene was quenched from the melt to −40 °C, crystallized from the glassy state at 20 or 40 °C and stored at the respective temperature for different aging times up to 7200 h. A significant increase in the tensile modulus and stress at yield and a decrease in strain at yield were observed for both aging temperatures. Differential scanning calorimetry (DSC) scans of aged material showed an endothermic annealing peak 15–30 °C above the previous aging temperature, the maximum temperature and enthalpic content of which increased with aging time. The position and the shape of the melting peak were not affected by aging. Scans of the storage modulus obtained from dynamic mechanical analyser measurements indicated a softening process starting at about 20 °C above the aging temperature and correlating with the annealing peak detected by DSC. Density measurements and wide-angle X-ray scattering investigations revealed that neither the crystallinity increased significantly nor did the crystal structure change. So the observed property changes induced by aging are attributed to microstructural changes within the amorphous phase. Furthermore, it could be shown by annealing experiments carried out at 60 °C, that aging above T _g is, analogous to aging below T _g (physical aging), a thermoreversible process. Received: 18 September 2000 Accepted: 2 January 2001     

Characterization,crystallization kinetics,and melting behavior of poly(ethylene succinate) copolyester containing 10 mol % butylene succinate

Copolyester was synthesized and characterized as having 89.9 mol % ethylene succinate units and 10.1 mol % butylene succinate units in a random sequence, as revealed by NMR. Isothermal crystallization kinetics was studied in the temperature range (T_c) from 30 to 73 °C using differential scanning calorimetry (DSC). The melting behavior after isothermal crystallization was investigated using DSC by varying the T_c, the heating rate and the crystallization time. DSC curves showed triple melting peaks. The melting behavior indicates that the upper melting peaks are associated primarily with the melting of lamellar crystals with various stabilities. As the T_c increases, the contribution of recrystallization slowly decreases and finally disappears. A Hoffman‐Weeks linear plot gives an equilibrium melting temperature of 107.0 °C. The spherulite growth of this copolyester from 80 to 20 °C at a cooling rate of 2 or 4 °C/min was monitored and recorded using an optical microscope equipped with a CCD camera. Continuous growth rates between melting and glass transition temperatures can be obtained after curve‐fitting procedures. These data fit well with those data points measured in the isothermal experiments. These data were analyzed with the Hoffman and Lauritzen theory. A regime II → III transition was detected at around 52 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2431–2442, 2008     

Layer structures. VI. Chiral sanidic polyesters derived from 2,5-bis (dodecyloxy) terephthalic acids and 4,4′-dihydroxybiphenyl

Copolycondensations of (S,S)-2,5-bis(2-methylbutyloxy) terephthaloylchloride with 2,5-bis(dodecyloxy)terephthaloylchloride and with 4,4′-bistrimethylsiloxybiphenyl yielded a series of novel chiral thermotropic copolyesters. These polyesters were characterized by elemental analyses, inherent viscosities, ¹H-NMR spectroscopy, optical rotations, optical microscopy, DSC measurements, and WAXS powder patterns recorded with synchrotron radiation under variation of the temperature. All homo- and copolyesters formed a solid sanidic layer structure with melting temperatures (T_m) ≥ 200°C. A broad enantiotropic nematic or cholesteric phase is formed above T_m with isotropization temperatures (T_is) in the range of 275–325°C. Yet, the T_m of the chiral homopolyester is so high (378°C) that the melting process is immediately followed by rapid degradation. The cholesteric phases of the copolyesters displayed unusual mobile schlieren textures, but a stable Grandjean texture was never obtained. Cholesteric domains consisting of loose bundles of more or less helical main chains are discussed as supramolecular order responsible for the observed textures and their pronounced temperature dependence. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 947–957, 1997     

Novel cellulose derivatives. IV. Preparation and thermal analysis of waxy esters of cellulose

Cellulose esters with linear aliphatic acyl substituents ranging in size from C₁₂ (lauric acid) to C₂₀ (eicosanoic acid) were prepared in homogeneous solution (DMAc/LiCl) using a novel synthetic method based on the use of a mixed p-toluenesulfonic/carboxylic acid anhydride. The resulting waxy cellulose esters had a high degree of substitution (DS), between 2.8 and 2.9, and showed little degradation. Thermal analysis of these cellulose derivatives by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed a series of transitions that represented motion by both ester substituents and cellulosic main chain. Broad crystallization and melting transitions attributed to side-chain crystallinity were observed in the range between −19 and +55°C; these side-chain T_m and T_c transition temperatures increased by 10°C per carbon atom of the ester substituent. The T_g of these derivatives increased linearly with increasing substituent size from 94°C for C₁₂ (cellulose laurate) to 134°C for C₂₀ (cellulose eicosanoate). Evidence of “main-chain” crystallization was not observed for these samples, except in the case of peracetylated C₁₂ and C₁₄ esters, which had T_m values of 96°C and 107°C, respectively. © 1996 John Wiley & Sons, Inc.     

Melting behavior of isotactic polystyrene revealed by differential scanning calorimetry and transmission electron microscopy

The triple melting behavior and lamellar morphologies of isotactic polystyrene isothermally crystallized from the glassy state have been investigated by differential scanning calorimetry (DSC), temperature-modulated DSC and transmission electron microscopy (TEM). The combination of thermal analysis measurements and morphological observations indicates that: (1) The lowest endothermic peak, the so-called “annealing peak” (T_a), is not associated with the melting of the subsidiary crystals formed by secondary crystallization as often suggested in the literature, but probably with a constrained interphase between the amorphous and crystalline regions; (2) Within spherulites two lamellar populations with different degrees of perfection (or thermal stability) are confirmed by direct TEM observations following partial melting experiments, which are responsible for the so-called double melting peaks (T_m,1 and T_m,2) at higher temperatures observed in DSC curves; (3) The highest endothermic peak (T_m,2) is partially originated from the melting of the recrystallized lamellae formed during heating process in DSC.