表面活性剂光催化降解动力学研究

为了研究光催化法对不同电荷类型表面活性剂的降解性能,在紫外光照射下,用TiO2光催化剂对阴离子表面活性剂十二烷基磺酸钠(SDS)、阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)和两性表面活性剂十八烷基甜菜碱(BS18)进行降解试验.同时,探讨了TiO2光催化剂加入量、表面活性剂初始质量浓度及初始pH对光降解的影响及其动力学过程.结果表明,3种表面活性剂的降解行为符合准一级动力学规律,3种表面活性剂降解速率快慢顺序为:BS18CTABSDS.SDS和BS18的最佳TiO2催化剂用量为1 g.L-1,而CTAB的最优用量为2g.L-1;CTAB和BS18的光降解速率随着活性剂初始质量浓度的增大而线性减小,SDS的降解速率则随活性剂初始质量浓度的增加而缓慢增大;CTAB和BS18在偏碱性条件下降解最快,而SDS在弱酸条件下具有最大的动力学降解速率.     

负载型活性炭/TiO2光催化降解苯酚的研究

在温和条件下(75℃和常压),通过在酸性水溶液中水解钛酸四丁酯并回流提高其结晶度,制备了锐钛矿型的TiO2.将此TiO2负载于粉末活性炭上,并用之来降解模拟废水苯酚.实验结果表明,该负载型催化剂的光催化效果要优于纯TiO2以及P25 TiO2加活性炭的混合体系.0.58g负载型催化剂降解0.4L浓度为100mg·L-1的苯酚溶液,经18W紫外灯光照6h后溶液中的苯酚去除率达到98%.同时,载体活性炭上吸附的苯酚量也随着光照时间逐渐减少,6h后残留的量仅为初始值的3.5%.     

负载型TiO2/活性炭的制备及光催化降解罗丹明B研究

通过溶胶-凝胶方法以活性炭(AC)为载体,制备负载型TiO2/AC,利用SEM、BET、XRD、Ranme、XPS对TiO2/AC的组成、结构、尺寸等特征进行分析和表征,并用紫外灯为光源,通过TiO2/AC、TiO2粉末和活性炭与TiO2粉末的混合物对可溶性罗丹明B的光催化降解效果的比较,探讨了TiO2/AC的光催化性能.结果表明,负载体中的TiO2是由30～60nm的球形颗粒组成,含有Ti,O,C等3种元素,颗粒间不发生团聚,其中一些C元素是由活性炭载体扩散到TiO2颗粒中的.由于活性炭载体与TiO2的协同作用以及高浓度Ti3+的影响,负载型TiO2/AC的光催化活性大.当TiO2/AC在250℃空气中热处理2h,再在氮气保护下500℃热处理2 h,TiO2的质量分数为(18±0.3)%时,负载型TiO2/AC对罗丹明B的光催化降解的表观反应常数k最大,为0.0077 min-1.     

Mo-TiO2/AC光催化剂的制备及可见光降解L-酸的研究

采用溶胶-凝胶法制备了Mo⁶⁺掺杂TiO₂光催化剂,并将其负载于粒状活性炭上,以1-萘酚-5-磺酸(L-酸)为模型反应物,研究了对L-酸的光催化作用并讨论了不同光源以及负载次数对L-酸的去除率和溶液的总有机碳去除率的影响.结果表明, Mo⁶⁺掺杂扩大了TiO₂催化剂的光谱响应范围.负载于活性炭上的掺杂二氧化钛为锐钛矿相,粒径约为17.8　nm.负载次数增多,催化剂的活性下降.Mo⁶⁺的掺杂不影响负载催化剂的紫外光活性及对L-酸的吸附能力.100　mg·L^-1的L-酸溶液加0.4 g催化剂,在可见光下反应4 h,掺杂催化剂对L-酸和溶液总有机碳的去除率分别为57%和53%,而未掺杂的催化剂去除率分别为13%和10%.催化剂反复使用4次,催化活性没有变化.     

Microwave photocatalytic degradation of Rhodamine B using TiO2 supported on activated carbon： Mechanism implication

The photocatalytic degradation of Rhodamine B (RhB) was carried out using TiO2 supported on activated carbon (TiO2-AC) under microwave irradiation. Composite catalyst TiO2-AC was prepared and characterized using X-ray di raction (XRD), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET). In the process of microwave-enhanced photocatalysis (MPC), RhB (30 mg/L) was almost completely decoloured in 10 min, and the mineralization e ciency was 96.0% in 20 min. The reaction rate constant of RhB in MPC using TiO2-AC by pseudo first-order reaction kinetics was 4.16 times of that using Degussa P25. Additionally, according to gas chromatography/mass spectrometry (GC/MS) and liquid chromatography/mass spectrometry (LC/MS) identification, the major intermediates of RhB in MPC included two kinds of N-de-ethylation intermediates (N,N-diethyl-N’-ethyl-rhodamine (DER)), oxalic acid, malonic acid, succinic acid, and phthalic acid, maleic acid, 3-nitrobenzoic acid, and so on. The degradation of RhB in MPC was mainly attributed to the destruction of the conjugated structure, and then the intermediates transformed to acid molecules which were mineralized to water and carbon dioxide.     

TiO2纳米管对水源水中MC-LR的光催化降解

采用“草酸+氟化铵”水相电解液体系通过阳极氧化法制备出了TiO₂纳米管材料,可有效光催化深度降解水源水中的微囊藻毒素（MC-LR）.结果表明,阳极氧化电压为20V、组分配比为1/12mol/L H₂C₂O₄·2H₂O+0.5wt% NH₄F、电解液pH值为4、阳极氧化时间1~2h的条件下制得的纳米管形貌最清晰,孔径为50nm左右,管长为250~600nm;催化剂经过500~600℃的温度煅烧后对MC-LR的光催化降解效率相对较高;pH值在3.5或8左右时,有利于MC-LR的光催化降解,且光化学反应符合准一级反应动力学模型;MC-LR的光催化降解机理主要包括产生的强氧化性·OH自由基对Adda支链共轭双键、Mdha氨基酸单双键以及Adda支链中甲氧基等部位的攻击氧化和肽键的水解.     

碳纳米管负载TiO2对1,2,4-三氯苯的光降解研究

碳纳米管负载TiO2复合光催化剂与纳米TiO2光催化剂对1,2,4-三氯苯的光催化降解效果,及降解动力学的研究结果表明,复合光催化剂比纳米TiO2有更好的光催化降解效果,经254 nm紫外光辐照60 min后,使用复合光催化剂的1,2,4-三氯苯降解了70%,而使用纳米TiO2为催化剂的1,2,4-三氯苯仅降解了51%...     

附载TiO2光催化降解咪蚜胺农药

以主波长３６５ｎｍ的黑炽荧光灯为光源,研究了由ＣＭＣ－Ｎａ附载ＴｉＯ２光催化降解咪蚜胺农药的过程。结果表明,咪蚜胺农药在３＊８Ｗ黑炽荧光灯照射下,经附载ＴｉＯ２作用３ｈ后可降解５０％以上,其光解可用假一级动力学方程表示。     

纳米TiO2对气相中甲醛光催化降解的研究

采用溶胶-凝胶法制备了掺杂金属离子的纳米TiO₂光催化剂,运用透射电镜和X射线衍射手段对催化剂的结构进行了表征,并将制备的光催化剂负载于不锈钢丝网、玻璃弹簧和泡沫镍板3种不同载体上,以室内空气典型污染物甲醛气体为模型反应物,研究了3种不同改性纳米TiO₂光催化剂对甲醛气体的光催化作用,3种光催化反应器的催化效率以及环境因素对光催化效率的影响,同时考察了催化剂的失活特征.结果表明:该负载型纳米TiO₂光催化剂具有较高的光催化活性,其中掺镧1.5%(质量分数)的TiO₂对甲醛的降解率最高,60 min达到91.5%,大于掺铁和掺银;泡沫镍板作为负载载体的光催化效率大于玻璃弹簧和不锈钢丝网;循环风量和不同波长紫外光对该光催化反应影响不大,反应中催化剂存在失活现象,但在清洁后能够恢复.      

TiO2光催化膜反应器的实验研究

采用溶胶-凝胶法,分别在炻器管、不锈钢管和玻璃管内壁负载TiO₂催化剂膜,在连续式光催化膜反应器中研究TiO₂膜光催化降解水中有机物的实际应用性能.结果表明:负载于玻璃表面的TiO₂膜上出现了Na元素的渗透,而在不锈钢表面所形成的TiO₂膜层均匀度较差;利用炻器管负载TiO₂催化降解亚甲基蓝(MB)的速率常数是不锈钢管和玻璃管的2倍;反应过程中鼓气与否所得到的苯酚光催化速率常数分别为0.143和0.103min-1;溶液在管内的流速为1和9 L/min时流体的Re分别为4 000和10 000.      

CTMAB/TiO_2表面修饰膨胀珍珠岩光催化降解水中对硝基苯酚

用溴化十六烷基三甲铵(CTMAB)和/或TiO2对膨胀珍珠岩(EP)进行表面修饰,获得不同表面修饰膨胀珍珠岩(CTMAB-EP,TiO2/CTMAB-EP,TiO2-EP和EP),研究其对水中对硝基苯酚的去除效果、吸附降解动力学以及最适条件.结果表明:膨胀珍珠岩对对硝基苯酚的吸附去除能力很小,对其用CTMAB进行表面修饰或负载TiO2均可显著提高对硝基苯酚的去除率,同时负载CTMAB和TiO2的膨胀珍珠岩对对硝基苯酚的去除率最高;环境修复材料用量、振荡时间、初始ρ(对硝基苯酚)和pH等对去除效果有一定影响.膨胀珍珠岩上负载的TiO2对对硝基苯酚的光催化降解能力受pH的影响不大,表面活性剂CTMAB在pH为8时对对硝基苯酚的吸附能力较强,pH为8时修复材料对对硝基苯酚的去除效果最好.     

Preparation and performance of photocatalytic regenerationable activated carbon prepared via sol-gel TiO2

Preparation of photocatalytic regenerationable activated carbon （AC） is the key step for the practical application of in situ regeneration of exhausted AC. A novel photocatalytic regenerationable AC was prepared by sol-gel TiO2 in this work. The adsorption and regeneration performance of TiO2/AC were evaluated using phenol as model compound. Scanning electron microscope （SEM） and nitrogen （77 K） adsorption isotherm were used to determine the surface area, pore structure and the distribution of TiO2. The results showed that with the increase of TiO2 loading, adsorption capacity of TiO2/AC decreased and the regeneration efficiency increased. The photocatalytic regenerationable AC with suitable TiO2 loading （2 wt%） exhibited suitable adsorption capacity and regeneration efficiency. TiO2 located mainly in the entrance of macro-pore of carbon. The prepared TiO2/AC exhibited similar surface structure and pore structure with material carbon.     

Inactivated properties of activated carbon-supported TiO2 nanoparticles for bacteria and kinetic study

The activated carbon-supported TiO₂ nanoparticles (TiO₂/AC) were prepared by a properly controlled sol-gel method. The effects of activated carbons (AC) support on inactivated properties of TiO₂ nanoparticles were evaluated by photocatalytic inactivation experiments of Escherichia coli. The key factors affecting the inactivation efficiency were investigated, including electric power of lamp, temperature, and pH values. The results show that the TiO₂/AC composites have high inactivation properties of E. coli in comparison with pure TiO₂ powder. The kinetics of photocatalytic inactivation of E. coli was found to follow a pseudo-first order rate law for TiO₂/AC composites, and kinetic behavior could be described in terms of a modified Langmuir-Hinshelwood model. The values of the adsorption equilibrium constants for the bacteria, K_c, and for the rate constants, k_r, were certainly depended on TiO₂ content. At 47 wt.% TiO₂ coatings with the highest rate constant, the K_c and k_r were 1.17 × 10⁻⁸L/cfu and 1.43 × 10⁶ cfu/(L·min), respectively. The variety of parameters shows significant effects on inactivation rate. The outer layer of bacteria decomposed first resulting in inactivation of cell, and with further illumination, the cells nearly decomposed.     

H2O2-固载型TiO2光催化对城市污水消毒作用研究

以泡沫镍作为载体,利用电沉积技术将纳米TiO2负载在泡沫镍上,制成固载型TiO2光催化反应器,在光催化反应器中加入H2O2,研究H2O2-固载型TiO2光催化反应系统对城市污水消毒效果。试验表明,固载型TiO2光催化反应中加入10 ppm H2O2,能大大提高紫外消毒效果,降低原水浊度对紫外消毒系统的影响,同时显著减少紫外消毒系统出水光复活现象。H2O2-固载型TiO2光催化反应系统,对降低紫外消毒投资和运行成本,提高紫外消毒效果稳定性,促进城市污水紫外消毒技术的推广具有重要意义。     

H_3PW_(12)O_(40)/TiO_2可见光下光催化降解孔雀石绿的研究

以钛酸四丁酯为原料,采用溶胶-凝胶法制备TiO2光催化剂,然后浸渍法制备出H3PW12O40/TiO2复合型光催化剂,并运用XRD、SEM、FT-IR和DRS对催化剂进行表征和分析.研究了可见光光照下H3PW12O40/TiO2对孔雀石绿降解的光催化活性,考察了浸渍量、催化剂用量、底物浓度、pH值对光催化降解率的影响.实验表明,在pH=5条件下,H3PW12O40/TiO2催化剂用量为0.3g.L-1,浓度为10mg·mL-1的孔雀石绿溶液在2L·min-1曝气、300W可见光下光照4h后光催化降解率为78%,比TiO2光催化活性提高了24%.     

二氧化钛光催化降解双酚AF研究

系统研究了双酚AF在二氧化钛溶液中的光催化降解行为。就溶解氧、二氧化钛投加量、氟离子浓度和双酚AF的初始浓度等因素对双酚AF降解的影响进行了详细讨论。研究重点是双酚AF的降解动力学以及在降解过程中所产生的氟离子浓度。当双酚AF的初始浓度是40μmol/L时,经过540 min的光催化降解,反应体系的总有机碳去除率超过97%,此时溶液中氟离子的浓度为0.98 mg/L。双酚AF在二氧化钛溶液中的降解符合Langmuir-Hinshelwood动力学模型,其降解动力学常数是1.21μmol/(L·min)。结果表明,二氧化钛光催化可以有效的去除双酚AF,并且不产生其它二次污染物。     

Enhanced photodegradation of phenolic compounds by adding TiO2 to soil in a rotary reactor

Photodegradation ofpentachlorophenol （PCP） and p-nitrophenol （PNP） in soil was carried out in a designed rotary reactor, which can provide the soil particles with continually uniform irradiation, and on a series of thin soil layers. TiO2, as a kind of environmental friendly photocatalyst, was introduced to the soil to enhance the processes. Compared with that on the soil layers, photodegradation of PCP at initial concentration of 60 mg/kg was improved dramatically in the rotary reactor no matter whether TiO2 was added, with an increase of 3.0 times in the apparent first-order rate constants. The addition of 1 wt% TiO2 furthered the improvement by 1.4 times. Without addition of TiO2, PNP （initial concentration of 60 mg/kg） photodegradation rate in the rotary reactor was similar to that on the soil layers. When 1 wt% additional TiO2 was added, PNP photodegradation was enhanced obviously, and the enhancement in the rotary reactor was 2 times of that on the soil layers, which may be attributed to the higher frequency of the contact between PNP on soil particles and the photocatalyst. The effect of soil pH and initial concentrations of the target compounds on the photodegradation in the rotary reactor was investigated. The order of the degradation rate at different soil pH was relative to the aggregation of soil particles during mixing in the rotary reactor. Photodegradation of PCP and PNP at different initial concentrations showed that addition of TiO2 to enhance the photodegradation was more suitable for contaminated soil with higher concentration of PCP, while was effective for contaminated soil at each PNP concentration tested in our study.     

负载型纳米TiO2/AC对偶氮染料的光催化降解研究

以钛酸四丁酯和粒状活性炭(AC)为主要原料,采用溶胶-凝胶-浸渍法制备出负载型纳米TiO2/AC催化剂.在流化床反应器中分别对2种典型的偶氮类染料橙黄G、活性艳红X-3B模拟废水进行了光催化降解研究,探讨了pH值、外加氧化剂对光催化降解率的影响,并对催化剂进行了回收再生利用试验.结果表明,TiO2/AC催化剂具有良好的光催化活性、吸附特性及可再生性,60 min后对2种染料反应的光催化降解率分别可达到99.71%和97 12%,反应180 min后的TOC去除率分别达到81.54%和81.99%;反应后TiO2/AC催化剂回收率大于95%,经焙烧再生后对橙黄G反应60 min的光催化降解率仍高达95.93%.     

复合催化剂氧化锡/网状碳的制备及光催化降解罗丹明B的研究

模板法与水热合成法制备了氧化锡/网状碳（SnO₂/RCs）复合材料,以改善纯相氧化锡（SnO₂）对印染废水的光催化处理效果.采用多种表征手段对所制备复合材料的微观结构、微观形貌、孔径分布和比表面积、光吸收性能、官能团以及光电性能进行了分析.通过可见光催化降解10 mg·L^-1的罗丹明B溶液的实验评估了所制备材料的光催化性能和循环稳定性.结果表明,在可见光条件下,SnO₂/RCs复合材料的光催化性能与纯SnO₂相比有显著提升,并且具有良好的循环稳定性.自由基捕获实验表明复合材料在降解有机污染物的过程中起作用的主要活性基团为空穴,超氧自由基和羟基自由基.复合材料光催化性能提高的原因归纳为：（1）能带结构改善所引起的对可见光的吸收性能的提高;（2）高的比表面积为光催化降解反应提供了更多的活性位点;（3）氧化锡与网状多孔碳所形成的异质结,使得电子传输/迁移能力提高,抑制了光生电子-空穴对的复合.     

泡沫镍负载纳米ZnO-SnO2光催化降解三氯乙烯

采用比较简单的共沉淀法技术制备了纳米ZnO-SnO2复合氧化物光催化剂,并将其负载在泡沫镍上制成了负载型纳米光催化剂,以三氯乙烯为挥发性有机物的模型反应物,研究了反应气流速、湿度等因素对反应的影响,同时考察了催化剂的失活特征,结果表明该负载型纳米光催化剂具有较高的光催化活性,同时具有较强的抗失活性能,在205h反应中没有出现失活现象．