Synthesis of sulfated titania supported on mesoporous silica using direct impregnation and its application in esterification of acetic acid and n-butanol

A new method has been developed for the preparation of sulfated titania (S-TiO₂) supported on mesoporous silica. The use of direct exchange of metal containing precursors for the surfactants in the as-synthesized MCM-41 substrate produced a product with high sulfur content without serious blockage of the pore structure of MCM-41. The pore sizes and volumes of the resultant S-TiO₂/MCM-41 composites were found to vary markedly with the loading of TiO₂. The strong acidic character of the composites obtained was examined by using them as catalysts for the esterification of acetic acid and n-butanol.     

微波辅助溶剂热合成In-Si共改性TiO2的增强光催化性能

利用微波辅助溶剂热法合成了In-Si 共改性的TiO₂ 光催化剂. 粉末X 射线衍射（XRD）、激光拉曼（Raman）光谱、N₂吸脱附（BET）、X射线光电子能谱（XPS）、光致发光（PL）光谱和紫外-可见漫反射光谱（UV-VisDRS）等实验表明,尽管掺杂和改性后TiO₂结晶度略有降低,但不影响光催化剂锐钛相的形成. Si 掺杂入TiO₂晶格使颗粒变小,比表面积变大. In 不能进入TiO₂晶格,在TiO₂表面形成了In₂O₃. 罗丹明B（RhB）降解实验显示,In-Si 共改性TiO₂表现出很高的紫外和可见光催化活性,Si：In：Ti 的摩尔比为0.03：0.02：1 的样品（IST-2）光催化活性最高,紫外光下3 min 即可将RhB降解完全,可见光下120 min RhB降解率为97%,这是由材料的高表面积,In₂O₃-TiO₂复合半导体之间高效电荷转移及染料敏化等共同作用所致. 对于苯酚,光催化降解则相对缓慢,700 min内尚不能降解完全.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

UV-Assisted Fabrication of Reduced Graphene Oxide Doped SiO<Subscript>2</Subscript>@TiO<Subscript>2</Subscript> Nanocomposites as Efficient Photocatalyst for Photodegradation of Rhodamine B

The core-shell nanostructure materials have gained great interests because of its excellent photocatalytic properties and promising applications in several fields. In this work, we prepared the core-shell SiO₂@TiO₂ nanocomposites by the versatile kinetics-controlled coating method. The graphene oxide (GO) was further reduced over SiO₂@TiO₂ using UV-assisted photocatalytic reduction method. The physicochemical properties of the as-prepared SiO₂@TiO₂/RGO nanocomposites were characterized by SEM, XRD, BET, EDS, and FTIR. Results showed that, TiO₂ was mainly composed of anatase phase with high crystallinity. Their photocatalytic activities were examined by the degradation of Rhodamine B (RhB) under UV light irradiation. The presence of RGO obviously improved the adsorption ability and photodegradation performance of the composites to RhB. The degradation kinetics of RhB can be described by the pseudo-first-order model. The optimum mass ratio of SiO₂@TiO₂ to RGO in the composite was 1/0.05 and the rate constant was about 4 times greater than that of the SiO₂@TiO₂.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Direct photo-oxidation of benzene to phenol over Ti/Si binary oxide prepared by sol-gel method

Titanium-silicon (Ti/Si) binary oxides having a varying Ti content were prepared using the sol-gel method and used as photocatalysts. The photo-oxidation of benzene to phenol was carried out using Ti/Si binary oxide catalysts in the presence of benzene, water and gaseous oxygen. The amounts of benzene used hardly affected the phenol yield. On the other hand, the addition of sulfuric acid into reaction solution led to the improvement of phenol formation. The H₂O₂ formation rate seemed to be related to the phenol yeilds. The photocatalytic reactivity of Ti/Si binary oxide having different TiO₂ contents was investigated and it was found to be dramatically enhanced in the range of lower TiO₂ contents. XANES, ESR and XRD spectroscopic investigations of these Ti/Si binary oxide catalysts indicated that Ti species were highly dispersed in SiO₂ matrices and existed in a tetrahedral coordination. The photo-irradiation of catalysts having tetrahedral Ti species seemed to effectively lead to the formation of H₂O₂ as an intermediate.     

Preparation and electrochemical properties of graphene‐supported Si‐TiO2 nanospheres as anode material for Li‐ion batteries

Graphene‐supported Si‐TiO₂ (Si‐Ti‐GE) composites have been synthesized by a simple polymerization and sintering method. In the Si‐Ti‐GE composites, many small Si‐TiO₂ particles are scattered on the graphene sheet, which can mitigate the agglomeration of the material and further reduce the particle size. The initial discharge capacities of Si‐TiO₂, Si‐Ti‐GE‐1, Si‐Ti‐GE‐2, and Si‐Ti‐GE‐3 are 336.9, 337.2, 339.8, and 356.6 mAh g⁻¹ at the current density of 200 mA g⁻¹, respectively. The discharge rate capacities of TiO₂, Si‐TiO₂, and Si‐Ti‐GE‐3 composites retain 57.5%, 41.7%, and 82.1% at the current density from 100 to 400 mA g⁻¹, respectively. Therefore, the introduction of graphene not only could facilitate the Li⁺ diffusion and electron transport but also could make better electrical conductivity.     

Mechanism of the formation of photosensitive nanostructured TiO<Subscript>2</Subscript> with low content of CdS nanoparticles

A method for synthesizing a CdS/TiO₂ composite material, active in the visible region, was described. The CdS/TiO₂ composite was obtained by the sol–gel synthesis of nanostructured TiO₂ in a medium of a stable colloidal solution of CdS nanoparticles. The TiO₂ matrix produced by the sol–gel process is amorphous and contains a nanocrystalline anatase phase, the content of which depends on the Ti(OBu)₄ hydrolysis rate. The content of CdS nanoparticles forming in the colloidal solution and participating in the TiO₂ matrix sensitization is determined by the initial CdS: Ti(OBu)₄ ratio. Although the content of CdS nanoparticles in the composite is low (no more than 3 wt %), the composite demonstrates catalytic activity in the visible region, thus proving the possibility of reducing the content of toxic CdS nanoparticles in the TiO₂ matrix without decreasing the photosensitivity of the CdS/TiO₂ composite.     

Comparison of the photonic effects of Mn-CNT/TiO<Subscript>2</Subscript> composites modified by different oxidants

Manganese-carbon nanotubes (CNTs) on titania (TiO₂) composites modified by different oxidants (KMnO₄, (NH₄)₂S₂O₈ and m-chlorperbenzoic acid (MCPBA)) were prepared with a sol-gel method. These composites were comprehensively characterized by the Brunauer-Emett-Teller (BET) method, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy EDX, Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV-vis absorption spectroscopy. The photoactivity of these materials prepared under visible light irradiation was tested using methylene blue in aqueous solution. The result shown that among the three oxidants, the MCPBA was the best one for the surface functionalization of CNTs and the manganese treated CNT/TiO₂ composite can enhance the photocatalytic activity. The proposed mechanism of the photodegradation of methylene blue on Mn-CNT/TiO₂ composites was present.     

Sol-gel preparation and characterization of Co/TiO<Subscript>2</Subscript> nanoparticles: Application to the degradation of methyl orange

Cobalt doped titania nanoparticles were synthesized by sol-gel method using titanium(IV) isopropoxide and cobalt nitrate as precursors. X-Ray diffraction (XRD) results showed that titania and Co/TiO₂ nanoparticles only include anatase phase. The framework substitution of Co in TiO₂ nanoparticles was established by XRD, scanning electron microscopy equipped with energy dispersive X-ray microanalysis (SEM-EDX) and Fourier transform infrared (FT-IR) techniques. Transmission electron microscopy (TEM) images confirmed the nanocrystalline nature of Co/TiO₂. The increase of cobalt doping enhanced “red-shift” in the UV-Vis absorption spectra. The dopant suppresses the growth of TiO₂ grains, agglomerates them and shifts the band absorption of TiO₂ from ultraviolet (UV) to visible region. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. Although the photocatalytic activity of undoped TiO₂ was found to be higher than that of Co/TiO₂ under UV irradiation, the presence of 0.5% Co dopant in TiO₂ resulted in a catalyst with the highest activity under visible irradiation.     

Analysis of preparation of TiO<Subscript>2</Subscript> particles by diffusion flame reactor for photodegradation of phenol and toluene

TiO₂ nanoparticles were produced in the diffusion flame reactor, and the size and anatase/rutile content of TiO₂ were examined by a Particle Size Analyzer and X-ray diffraction, respectively. Increase in fuel/O₂ ratio, initial concentration of TiCl₄ or total gas flow rate causes the larger particle size and the higher rutile composition. The photocatalytic activities of TiO₂ powders were tested on the decompositions of phenol and toluene in the aqueous solution under UV irradiation. The degradation rate increases as the TiO₂ particle size decreases and as the initial concentration of phenol or toluene increases. The photodegradation rate of phenol by TiO₂ particles is higher than that of toluene at the same process conditions. The computational method was used to simulate the gas temperature, velocity and species mass fractions inside the diffusion flame reactor during synthesis of TiO₂ nanoparticles. The measured and simulated temperature results were compared on several positions above the burner and both of them show good agreements. The typical contours of TiCl₄, TiO₂ mass fractions and gas velocities in flame reactor were presented.     

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Reaction of the novel Ru<Subscript>3</Subscript>(CO)<Subscript>10</Subscript>[Ph<Subscript>2</Subscript>P(CH<Subscript>2</Subscript>)<Subscript>2</Subscript>Si(OEt<Subscript>3</Subscript>)]<Subscript>2</Subscript> complex on SBA-15 and MCM-41 mesoporous silicas

The reaction of Ru₃(CO)₁₂ with 2(diphenylphosphino)ethyl-triethoxysilane (DPTS) in hydrocarbons, leads to the functionalized Ru₃(CO)_12−n [Ph₂P(CH₂)₂Si(OEt₃)] _n (n = 1,2) complexes. The complex with two phosphine substituents was chemically anchored on mesoporous silicas, SBA-15 and MCM-41, in order to obtain two hybrid materials characterized by a different localization of the metal centre on the surface of the porous supports. A detailed investigation of the cluster, before and after chemical anchoring on the mesoporous silicas, was pursued. Particular attention was also devoted to the study of the morphological, structural and textural properties of the metal-functionalised silicas (Ru/SBA-15 and Ru/MCM-41) by infrared spectroscopy (FT-IR), scanning electron microscopy, X-ray diffraction and N₂ physisorption analysis.     

Interpretation of the difference of optimal Mo density in MoS<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and MoS<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> HDS catalysts

The first part of this paper deals with the morphology of the MoS₂ phase and its oxide precursor, the MoO₃ phase, mainly from a geometrical point of view. After giving a brief review of the literature describing the structure of these compounds, Mo densities in both phases were calculated along various crystallographic planes. Further, using structural models recently proposed by others, Mo densities in MoS₂ were also calculated in the case of an epitactic growth on γ-Al₂O₃ and TiO₂ model surfaces. Then, the calculated Mo densities were compared with experimental results (Mo density when HDS activity is maximal) previously obtained for catalysts constituted of MoS₂ supported on a low SSA TiO₂, a high SSA TiO₂ and a conventional γ-alumina. It was suggested that either on alumina or titania the MoS₂ phase is growing as (100) MoS₂ planes. However, while on the alumina the optimal MoS₂ phase might be constituted of dispersed MoS₂ slabs covering only a part of the alumina surface (2.9–3.9 Mo atoms/nm²), on titania the optimal MoS₂ phase might be constituted of a uniform MoS₂ monolayer (5.2 atoms/nm² for the high SSA titania, which is equal to the Mo density of a perfect MoS₂ (100) plane). This difference may originate in the creation of a 'TiMoS' phase enhancing the S atoms mobility over Mo/TiO₂-sulfided catalysts. Indeed, while in the case of a γ-alumina carrier the active sites (labile S atoms) are located on the edge of MoS₂ slabs making the ratio Mo_edge/Mo_total a crucial parameter for the catalytic performances, in the case of a titania carrier the labile sulfur atoms might be statistically distributed all over the TiMoS active phase. Further, the higher Mo density observed over the high SSA titania (5.2 atoms/nm²) when compared to that over the low SSA titania (4.2 atoms/nm²) was supposedly due to the pH-swing method advantageously used to prepare the former carrier. Indeed, this method allows giving a solid with enhanced mechanical properties providing a good stability to the derived catalysts under experimental conditions. In addition, this TiO₂ carrier exhibits a great homogeneity, with a surface structure substantially uniform, which might be adequate for a long-range growth of (100) MoS₂ slabs.     

Controllable synthesis of titania/reduced graphite oxide nanocomposites with various titania phase compositions and their photocatalytic performance

A facile method is presented for preparing TiO2 /reduced graphite oxide(RGO) nanocomposites with phase-controlled TiO2 nanoparticles via redox reaction between the reductive titanium(Ⅲ) precursor and graphite oxide(GO),and a series of TiO2 /RGO composites with various TiO2 phase compositions were obtained.In all the titania/RGO composites,the TiO2 nanoparticles were uniformly distributed on the surface of the RGO.The TiO2 consisted of anatase phase particles in the form of square-plates with edges less than 10 nm and the rutile phase nanorods in diameters less than 10 nm.The performances of the as-prepared TiO2 /RGO composites were investigated on catalytically degrading phenol under visible light irradiation.The TiO2 /RGO composites can effectively degrade phenol under visible light irradiation,and the phase composition of TiO2 in the composites significantly influences the activities of these catalysts.     

Preparation of Solid Superacid Catalysts and Oil Oxidative Desulfurization Using K<Subscript>2</Subscript>FeO<Subscript>4</Subscript>

A \(\rm{SO_4^{2-}}\)/MCM-41 superacid catalyst was prepared by impregnation and characterized by various methods. A novel procedure for oxidative desulfurization of simulated light fuel oil using K₂FeO₄ over \(\rm{SO_4^{2-}}\)/MCM-41 was developed. Fourier transform infrared spectroscopy (FTIR) and low-angle X-ray diffractometry (XRD) show that the material synthesized by the precipitation-sol-hydrothermal method is mobil composition of matter no. 41 (MCM-41). Thermogravimetry/differential thermal analysis (TG-DTA) shows that when the calcination temperature is higher than 300°.     

Chemical solution processing and characterization of Ba(Zr,Ti)O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> layered thin films

Ba(Zr,Ti)O₃/LaNiO₃ layered thin films have been synthesized by chemical solution deposition (CSD) using metal-organic precursor solutions. Ba(Zr,Ti)O₃ thin films with smooth surface morphology and excellent dielectric properties were prepared on Pt/TiO _x /SiO₂/Si substrates by controlling the Zr/Ti ratios in Ba(Zr,Ti)O₃. Chemically derived LaNiO₃ thin films crystallized into the perovskite single phase and their conductivity was sufficiently high as a thin-film electrode. Ba(Zr,Ti)O₃/LaNiO₃ layered thin films of single phase perovskite were fabricated on SiO₂/Si and fused silica substrates. The dielectric constant of a Ba(Zr_0.2Ti_0.8)O₃ thin film prepared at 700°C on a LaNiO₃/fused silica substrate was found to be approximately 830 with a dielectric loss of 5% at 1 kHz and room temperature. Although the Ba(Zr_0.2Ti_0.8)O₃ thin film on the LaNiO₃/fused silica substrate showed a smaller dielectric constant than the Ba(Zr_0.2Ti_0.8)O₃ thin film on Pt/TiO _x /SiO₂/Si, small temperature dependence of dielectric constant was achieved over a wide temperature range. Furthermore, the fabrication of the Ba(Zr,Ti)O₃/LaNiO₃ films in alternate thin layers similar to a multilayer capacitor structure was performed by the same solution deposition process.     

TiO<Subscript>2</Subscript>-based nanopowders obtained from different Ti-alkoxides

Pure TiO₂ and S-doped TiO₂ sol–gel nanopowders were prepared by controlled hydrolysis-condensation of titanium alkoxides. The influence of different Ti-alkoxides (tetraethyl-, tetraisopropyl- and tetrabutyl-orthotitanate) used in obtaining TiO₂ porous materials in similar conditions (water/alkoxide ratio, solvent/alkoxide ratio, pH and temperature of reaction) has been investigated. The relationship between the synthesis conditions and the properties of titania nanosized powders, such as thermal stability, phase composition, crystallinity, morphology and size of particles, BET surface area and the influence of dopant was investigated. The nature of the alkyl group strongly influences the main characteristics of the obtained oxide powders, fact which is pointed out by thermal analysis, X-ray diffraction, TEM and BET surface area measurements.     

Photocatalytic activity of a mesoporous TiO<Subscript>2</Subscript>/Ni composite in the generation of hydrogen from aqueous ethanol systems

TiO₂/Ni metal-semiconductor composites were prepared from mesoporous titanium dioxide obtained by sol-gel precipitation in the presence of a structure-forming template. The photocatalytic activity of mesoporous TiO₂/Ni composites in the generation of hydrogen from aqueous ethanol mixtures was discovered and studied in detail.__________Translated from Teoreticheskaya i Éksperimentalnaya Khimiya, Vol. 41, No. 1, pp. 24–29, January–February, 2005.