溶胶-凝胶辅助水热双模板法制备球形介孔TiO_2

以聚乙二醇和共嵌段化合物F127为双模板剂,采用溶胶-凝胶辅助水热法制备了球形介孔TiO2(MS-TiO2).采用扫描电镜、透射电镜、X射线衍射、热重分析和低温N2吸附-脱附对样品进行了结构表征,并以苯酚为降解模型物在紫外光下对其活性进行了评价.结果表明,所得TiO2为球形介孔结构,孔径为6.5～12.6nm,比表面积最高可达106.9m2/g,孔体积0.21cm3/g,球形颗粒直径200～300nm,由粒径为15～20nm的小晶粒组成.随着焙烧温度的升高,TiO2的比表面积和孔体积减小,孔径增大.双模板剂的使用比单一模板剂更能形成稳定的立体网状球形胶束,并有效抑制TiO2前驱体的团聚,诱导其形成球形介孔结构.其中,在500oC下焙烧所制MS-TiO2样品表现最高的光催化活性,苯酚降解率达86.4%,为TiO2的1.3倍.     

高热稳定性纳米Au/TiO2催化剂的制备与表征

 采用三嵌段共聚物聚乙醚-聚丙醚-聚乙醚EO20PO70EO20 (P123)为有机模板剂合成了介孔TiO2载体,用沉积-沉淀法制得Au/TiO2催化剂. 运用N2 吸附-脱附、 X射线衍射、 X射线光电子能谱和高分辨电镜技术对催化剂的结构与形貌进行了表征. 采用P123模板剂合成的TiO2具有较均匀的介孔结构,孔径集中在6.1 nm附近,负载金后,其介孔结构保持良好,但孔径下降至5.4 nm. 400 ℃焙烧后,介孔TiO2负载的Au催化剂中Au主要以金属态存在. 负载在三种TiO2载体(介孔TiO2、溶胶-凝胶法合成的TiO2和工业TiO2)上的Au晶粒大小和分散度差异较大,其中介孔TiO2载体更有利于金的分散,以该载体制备的催化剂400 ℃焙烧后金的晶粒尺寸在1～5 nm范围内,催化剂显示了很好的CO氧化活性和抗热稳定性,即使在420 ℃焙烧,其室温下CO的转化率也在90%以上. 而溶胶-凝胶法制备的TiO2和工业TiO2负载的纳米金催化剂中,金晶粒尺寸约为10 nm,催化剂的CO氧化活性和抗热稳定性较差.     

介孔二氧化钛微球的合成与表征

以非离子型表面活性剂TO8为模板剂,采用溶胶凝胶-表面活性剂法合成了介孔TiO2微球．运用SEM,TG—DTA,XRD,BET,UV等测试手段对其进行表征并探讨了TO8的加入量和不同热处理方式对样品形貌、结构的影响．实验表明TiO2微球呈单分散性,球径约800nm;介孔结构,孔径约3．5nm且分布较窄．TiO2微球为单一锐钛矿相,在190～380nm范围内有强紫外吸收．热处理时采取分步焙烧、控制升温速率和高温焙烧时间,可获得比表面较大的介孔TiO2微球．     

锐钛矿型纳米TiO2介孔粉体表面织构的研究

以硫酸钛和尿素为原料,聚乙二醇-1000为空间构造剂,104℃下经尿素水解均匀沉淀法研制颗粒分散均匀、粒径可控的高热稳定性锐钛矿型纳米TiO2介孔粉体,并对其晶相、颗粒大小、比表面积、形貌和孔道结构进行了表征.结果表明,未经任何热处理的TiO2粉体即为锐钛型晶相,颗粒为均匀分散的类球型颗粒,且颗粒间形成直通型的介孔孔道,其孔径在10～30nm之间.控制焙烧温度可以达到控制颗粒大小及形貌的目的,经850℃焙烧5h的样品仍保持锐钛矿型晶相,未出现向金红石型晶相转变的迹象.     

Si掺杂介孔SO_4~(2-)/TiO_2的非模板剂法合成及表征

在不使用模板剂的条件下,以工业硫酸氧钛溶液为原料合成介孔偏钛酸前驱体,再经正硅酸乙酯浸渍焙烧制备了具有良好热稳定性的Si掺杂介孔SO42-/TiO2.采用X射线衍射、N2吸附-脱附、扫描电镜、X射线能谱和傅里叶变换红外光谱等表征方法对样品的组成和结构进行了分析,并考察了该材料在亚甲基蓝氧化降解反应中的光催化性能.结果表明,在焙烧过程中,被吸附在偏钛酸孔道内的正硅酸乙酯发生水解,并与偏钛酸孔壁上的自由羟基形成Ti-O-Si键;Si进入二氧化钛骨架中,对孔结构起到了支撑作用,从而提高了介孔SO42-/TiO2的热稳定性.700℃焙烧2 h后,Si掺杂介孔SO42-/TiO2材料的比表面积仍达到189 m2/g,平均孔径为2.8 nm.400℃焙烧的样品在亚甲基蓝降解反应中表现出较好的光催化活性.     

介孔TiO2的水热法制备及其光催化性能

以二钛酸钾(K2Ti2O5)经离子交换得到的无定形水合二钛酸(H2Ti2O5·xH2O)为原料, 与葡萄糖溶液在220 ℃下进行水热反应, 再在空气中520 ℃焙烧, 制备出介孔TiO2. 用扫描电子显微镜(SEM)、X射线衍射(XRD)、N2吸附、透射电子显微镜(TEM)等技术对样品进行了表征. 结果表明, 该介孔TiO2具有微米级棒状或针状形貌, 晶粒大小为12.3 nm, 比表面积为106 m2·g-1, 孔容为0.31 cm3·g-1, 孔径为8.06 nm, 焙烧处理后晶型仍是锐钛矿相. 水热生成的碳抑制了晶粒的团聚生长和晶型的转变, 提高了介孔TiO2的热稳定性. 甲基橙降解实验评价了介孔TiO2的光催化性能, 结果发现其活性与商用TiO2催化剂P25相当, 而其较大的粒径更容易回收再利用. 以碘化钾为探针反应, 表明介孔TiO2的光催化机制以光生空穴氧化为主.     

介孔TiO2的水热法制备及其光催化性能

以二钛酸钾(K2Ti2O5)经离子交换得到的无定形水合二钛酸(H2Ti2O5·xH2O)为原料,与葡萄糖溶液在220℃下进行水热反应,再在空气中520℃焙烧,制备出介孔TiO2.用扫描电子显微镜(SEM)、X射线衍射(XRD)、N2吸附、透射电子显微镜(TEM)等技术对样品进行了表征.结果表明,该介孔TiO2具有微米级棒状或针状形貌,晶粒大小为12.3 nm,比表面积为106 m2·g-1,孔容为0.31 cm3·g-1,孔径为8.06 nm,焙烧处理后晶型仍是锐钛矿相.水热生成的碳抑制了晶粒的团聚生长和晶型的转变,提高了介孔TiO2的热稳定性.甲基橙降解实验评价了介孔TiO2的光催化性能,结果发现其活性与商用TiO2催化剂P25相当,而其较大的粒径更容易回收再利用.以碘化钾为探针反应,表明介孔TiO2的光催化机制以光生空穴氧化为主.     

Si掺杂介孔SO2-4/TiO2的非模板剂法合成及表征

在不使用模板剂的条件下,以工业硫酸氧钛溶液为原料合成介孔偏钛酸前驱体,再经正硅酸乙酯浸渍焙烧制备了具有良好热稳定性的Si掺杂介孔SO2-4/TiO2.采用X射线衍射、N2吸附-脱附、扫描电镜、X射线能谱和傅里叶变换红外光谱等表征方法对样品的组成和结构进行了分析,并考察了该材料在亚甲基蓝氧化降解反应中的光催化性能.结果表明,在焙烧过程中,被吸附在偏钛酸孔道内的正硅酸乙酯发生水解,并与偏钛酸孔壁上的自由羟基形成 Ti - O - Si 键;Si进入二氧化钛骨架中,对孔结构起到了支撑作用,从而提高了介孔SO2-4/TiO2的热稳定性.700 ℃焙烧 2 h 后,Si掺杂介孔SO2-4/TiO2材料的比表面积仍达到189 m2/g,平均孔径为2.8 nm.400 ℃焙烧的样品在亚甲基蓝降解反应中表现出较好的光催化活性.     

TiO2介孔薄膜的制备及紫外光电响应性质

采用蒸发诱导自组装法制备了高度有序的TiO2介孔薄膜. 利用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等分析手段对其进行了表征. 结果表明, 所得样品的孔径约为5 nm, 孔道规则, 且骨架为纯锐钛矿结构. 紫外-可见光谱(UV-Vis)的表征结果表明, 制备的TiO2介孔薄膜对波长小于380 nm的紫外线有很强的吸收. 对TiO2介孔薄膜的I-V(电流-电压)特性进行了表征, 发现加光后其I-V曲线由暗态时的肖特基特性转变为欧姆特性, 表明TiO2介孔薄膜对紫外光有很敏感的光电响应.     

锐钛相介孔SO2-4/TiO2的声化学制备及结构和催化酯化性能

不使用有机模板剂,采用超声化学法一步水解制得吸附硫酸根的介孔偏钛酸,500℃焙烧得到介孔SO2-4/TiO2固体超强酸.用XRD、TFEM、FTIR、低温氮吸附-脱附等手段对催化剂结构进行了表征.结果表明,硫酸根在焙烧过程中与前驱体介孔偏钛酸孔壁上自由羟基的键合起到了孔结构导向及支撑作用,500℃焙烧后样品具有161 m2·g-1的比表面积及4.1 nm的平均孔径,酸强度H0介于-14.52与-16.02之间,硫含量为2.8%,晶型全部为锐钛矿相,介孔SO2-4/TiO2具有较大比表面、强酸特性和稳定性.催化合成富马酸二甲酯的最佳条件为:n(甲醇):n(富马酸)=6:1,催化剂用量为1.0%(反应物总质量),带水剂苯用量为10 mL,反应时间为3 h,催化剂重复使用7次,酯化率大于90%.     

Synthesis and characterization of ultrahigh crystalline TiO2 nanotubes

Ultrahigh crystalline TiO2 nanotubes were synthesized by hydrogen peroxide treatment of very low crystalline titania nanotubes (TiNT-as prepared), which were prepared with synthesized TiO2 nanoparticles by hydrothermal methods in an aqueous NaOH solution. Thus, prepared ultrahigh crystalline TiO2 nanotubes (TiNT-H2O2) showed comparable crystallinity with high crystalline TiO2 nanoparticles. The details of nanotubular structures were elucidated by high resolution-transmission electron microscopy (HR-TEM), field emission-scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis in transmission electron microscopy (TEM-EDX), X-ray diffraction (XRD), photoluminescence (PL), and BET surface area. TiNT-H2O2 was found to be a multiwalled anatase phase only with an average outer diameter of approximately 8 nm and an inner diameter of approximately 5 nm and grown along the [001] direction to 500-700 nm long with an interlayer fringe distance of ca. 0.78 nm. The photocatalytic activity of TiNT-H2O2 was about 2-fold higher than those of TiNT-as prepared, synthesized TiO2 nanoparticles, and TiO2-P25 (Degussa) in the photocatalytic oxidation of trimethylamine gas under UV irradiation.     

Synthesis of Mg-Doped TiO2 nanoparticles under different conditions and its photocatalytic activity

In this study, TiO(2)- and Mg-doped TiO(2) nanoparticles with different dopant contents were prepared by sol-gel method. The prepared photocatalysts were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and diffuse reflectance spectroscopy (DRS) techniques. The results of BET analysis indicated a pore diameter of 8 nm and surface area of 48.5 m(2) g(-1). XRD patterns of pure and doped TiO(2) nanoparticles at 450 °C revealed that all phases are anatase. The particle size obtained from TEM was less than 20 nm. The band gap energy of Mg-doped TiO(2) nanoparticles was lower than that of TiO(2) . The photocatalytic activity of the pure and doped nanoparticles has been compared in the removal of C.I. Acid Red 27 (AR27). The photocatalytic activity of Mg-doped (0.2 mol%) TiO(2) for the degradation of AR27 was higher than that of bare TiO(2) nanoparticles. Results of total organic carbon analysis and changes in the AR27 UV-Vis peaks indicated 99% mineralization and extinguishing of all peaks in UV and visible regions is possible with Mg-doped TiO(2) nanoparticles. Removal efficiency of AR27 was sensitive to the parameters such as catalyst dose, pollutant concentration and light intensity.     

Synthesis and photocatalytic activity of TiO2 nanoparticles prepared by chemical vapor condensation method with different precursor concentration and residence time

Nanosized TiO(2) photocatalysts were synthesized using a chemical vapor condensation method under a range of synthesis conditions (precursor vapor concentration and residence time in a tubular electric furnace). X-ray diffraction showed that the prepared TiO(2) powders consisted mainly of anatase (>94%) with a small amount of rutile. The mean particle diameter from the Brunauer-Emmett-Teller surface area and transmission electron microscopy measurements ranged from 9.4 to 16.6 nm. The specific surface area (92.5-163.5 m(2) g(-1)) of the prepared TiO(2) powders was found to be dependent on the synthesis conditions. The content of hydroxyl groups on the surface of the prepared TiO(2) sample was higher than those on commercial TiO(2), resulting in increased photocatalytic oxidation. The photocatalytic activity of the TiO(2) samples prepared in a methylene blue solution was strongly dependent on the crystallinity and specific surface area, which were affected by the TTIP vapor concentration and residence time.     

水洗处理对Au/TiO2催化剂光催化活性的影响

以Au(S2O3)3-2为金前驱体, 分别采用水洗(W)和旋蒸(E)工艺制备了Au/TiO2催化剂. 用UV-Vis漫反射光谱(DRS)、X 射线衍射(XRD)、透射电子显微镜(TEM)和原子吸收光谱(AAS)对制备的催化剂样品进行了表征, 通过光催化降解甲基橙对催化剂光催化活性进行了评价. 结果表明, 通过水洗处理, 催化剂样品表面形成了具有较好分散性的金纳米粒子(2-5 nm), 而旋蒸工艺制备的样品表面形成一层金的包覆结构. Au/TiO2催化剂的光催化活性与制备工艺密切相关. 在相似的金负载量下, 水洗法制备的样品比旋蒸法制备的样品具有更高的光催化活性.     

单根TiO2纳米线一维电子输运性能

采用电化学诱导溶胶-凝胶法, 在多孔氧化铝模板(AAO)的纳米孔道内制备了直径分别为60 和20 nm的锐钛矿型TiO₂纳米线阵列. 利用原子力显微镜(AFM)技术, 在半接触模式下得到了TiO₂纳米线的形貌像, 在接触模式下测量了单根TiO₂纳米线的I-V曲线. TiO₂纳米线的电子输运性能表现为半导体的性质. TiO₂纳米线的导通电压值明显小于TiO₂块体,并且随着TiO₂纳米线直径的减小, 导通电压值增大.     

同轴静电纺丝法在纳米中空TiO2纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸四正丁酯和PVP溶胶/银颗粒为前驱体, 以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维. 将双组分纤维在200 ℃下热处理去除乙醇与表面吸附水后, 继而在空气气氛中焙烧至600 ℃, 可以得到在内表面上沉积银颗粒的TiO2纳米管, 银颗粒的直径为5-40 nm, TiO2纳米管的外径150-300 nm, 管臂厚10-20 nm. 用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征. 中空纤维的直径和管壁可以通过改变电纺参数来调节. 与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较, Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

Formation and properties of composites based on microgels of a responsive polymer and TiO2 nanoparticles

Organic-inorganic composites were prepared with titanium dioxide (TiO2) nanoparticles embedded within colloidal particles of a cross-linked, thermally responsive polymer. To promote the incorporation of unaggregated nanoparticles of TiO2, temperature responsive microspherical gels (microgels) of N-isopropylacrylamide (NIPAM) with interpenetrating (IP) linear chains of poly(acrylic acid) (PAAc) were synthesized. Dynamic light scattering (DLS) measurements revealed that these microgels reversibly shrink and swell in diameter from 300-400 nm to 600-800 nm with temperature. Two types of nanoparticles of TiO2 were immobilized within the IP-microgels-fine TiO2 nanoparticles synthesized by the hydrolysis of titanium(IV) isopropoxide and commercially available Degussa P25. Characterization of the composite was conducted using transmission electron microscopy (TEM) and UV-vis absorption spectroscopy from which it was determined that the extent of loading of the TiO2 within the colloidal particles can be easily manipulated from a low value of 10% (weight) to a value as high as 75%. The TiO2 nanoparticles were in a dispersed state within the microgels and the composites showed rapid (approximately minutes) sedimentation, which is useful for gravity separations. By using turbidometry to characterize the settling behavior of the organic-inorganic composites, it was found that the settling time decreases as the content of TiO2 increases within the particles.     

同轴静电纺丝法在纳米中空Ti02纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶,钛酸四正丁酯和PVP溶胶,银颗粒为前驱体,以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维.将双组分纤维在200℃下热处理去除乙醇与表面吸附水后,继而在空气气氛中焙烧至600℃.可以得到在内表面上沉积银颗粒的TiO2纳米管,银颗粒的直径为5-40 nm,TiO2纳米管的外径150-300 nm.管臂厚10-20 nm.用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征.中空纤维的直径和管壁可以通过改变电纺参数来调节.与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较,Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

Synthesis of biomorphological mesoporous TiO2 templated by mimicking bamboo membrane in supercritical CO2

A new approach is presented for preparing biomorphological mesoporous TiO2 templated by mimicking bamboo inner shell membrane via supercritical CO2 (SCCO2) transportation through titanium tetrabutyloxide (TTBO). The analysis of wide-angle X-ray powder diffraction (XRD) showed the prepared TiO2 in phase of anatase, and the small-angle XRD revealed the presence of mesopores without periodicity. The product exhibited the shape of crinkled films and extended in two dimensions up to centimeters. The electron microscopic observation showed that the TiO2 films were around 200 nm in thickness, and across the films there were numerous round or ellipse-shaped mesopores, being 10-50 nm in diameter, which were formed by the close packing of TiO2 particles. High-resolution transmission electron microscope (HRTEM) displayed that the single TiO2 particle size was about 12.5 nm. The UV-vis absorption spectrum was transparent in the wavelength of 320-350 nm for suspensions of the prepared mesoporous TiO2 in ethanol at the concentration of 5.0 mg/l. The mesoporous TiO2 prepared with the aid of SCCO2 exhibited an obvious blue shift compared with the TiO2 prepared by sol-gel infiltration. The possible mechanism for the formation of the mesoporous TiO2 is summarized into a biomimetic mineralization pathway. First, TTBO was transported to the membrane surface via SCCO2, and then condensed. Hydrolysis reactions between the functional groups of organic membrane and TTBO took place to form the nuclear TiO2, and the TiO2 seeds grew around the organic membrane into TiO2 mesoporous materials. The approach provides a low-cost and efficient route for the production of ceramics nanomaterials with unique structural features, which may have potential application in designing UV-selective shielding devices [S. Zhao, X.H. Wang, S.B. Xin, Q. Jiang, X.P. Liang, Rare Metal Mater. Eng. 35 (2006) 508-510].