考虑表面效应的形状记忆合金纳米梁弯曲特性研究

形状记忆合金(Shape Memory Alloys, SMAs)因其具有形状记忆效应和超弹性,在航空航天、生物医疗、微机电系统领域中得到了广泛的应用．当微结构尺度达到微纳米,表面效应对微结构力学性能的影响是十分显著的．本文基于梁弯曲变形理论以及Gurtin-Murdoch表面弹性理论,考虑拉压不对称、温度对于SMA纳米梁的影响,建立了考虑表面效应的SMA纳米梁相变力学模型．分析了弯曲载荷、温度、表面残余应力以及表面弹性模量对SMA纳米梁力学性能的影响规律．研究表明在SMA纳米梁相变阶段,忽略和考虑表面效应所得的截面应力及应变相对误差较为明显;在相同弯矩下,随温度的增加SMA纳米梁的截面应力随之增加,并且表面效应对其影响有减小趋势;表面残余应力对SMA纳米梁的影响显著．该文研究结果为SMA纳米梁在微机电领域的设计以及应用提供了一定基础与依据．     

PTT黏弹性流体的光滑粒子动力学方法模拟

运用光滑粒子流体动力学(smoothed particle hydrodynamics, SPH)方法对基于PHan-Thien-Tanner (PTT)模型的黏弹性流动进行了数值模拟. 首先, 利用SPH方法模拟了基于PTT模型的平板 Poiseuille流, 通过与文献结果的比较, 验证了SPH方法模拟黏弹性流动的准确性和有效性; 随后, 基于PTT模型对黏弹性自由表面流-液滴碰撞问题进行了SPH模拟, 研 究了PTT模型中拉伸参数对碰撞过程的影响. 为了解决张力不稳定问题, 采用简化的 人工应力公式. 数值结果表明, SPH方法可有效而灵活地模拟黏弹自由表面流问题.     

基于表面弹性理论的开裂椭圆孔断裂力学研究

研究纳米尺度时开裂椭圆孔的III型断裂性能。基于表面弹性理论和保角映射技术,利用复势函数理论获得了缺陷(裂纹和椭圆孔)周围应力场和裂纹尖端应力强度因子的闭合解答。所得结果具有一般性,许多已有和新的解答可由本文退化的特殊情形得到。利用解析结果讨论了缺陷的绝对尺寸、椭圆孔的形状比以及裂纹的相对尺寸对应力强度因子的影响。结果表明：考虑表面效应且缺陷尺寸在纳米尺度时,应力强度因子具有显著的尺寸依赖效应;应力强度因子随椭圆孔形状比的变化规律受缺陷表面常数的影响;缺陷表面效应的影响取决于椭圆孔的形状比,非常大的形状比屏蔽了表面效应的影响;裂纹相对尺寸非常小时表面效应影响较弱,裂纹相对尺寸较大时表面效应较为明显。     

考虑表面效应的双层圆板的自由振动分析

考虑微生化传感器中谐振器的结构特点,基于Kirchhoff薄板理论与表面弹性理论推导了考虑表面效应的双层圆板的自由振动方程.使用伽辽金法得到了近似解.分析了硬化与软化表面效应与表面残余应力对双层圆板固有频率的影响.结果表明,与已有简化的单层圆板模型相比,现有考虑表面效应的双层板模型会得到与之不同的固有频率.随着板厚与上...     

考虑尺度效应的微梁静态弯曲数值分析

基于修正偶应力理论及表面弹性理论,本文提出了一种新的双曲线剪切变形梁模型,用于均匀微尺度梁的静态弯曲分析。该理论可以直接利用本构关系获得横向剪切应力,满足梁顶部和底部的无应力边界条件,避免了引入剪切修正因子。根据广义Young-Laplace方程建立了梁的内部与表面层的应力连续性条件,单一的变量场可以描述梁的位移模式。通过在位移场中考虑表面层厚度以及表面层的应力连续条件,可以使新模型能够更准确地预测微尺寸和表面能相关的尺度效应。通过Hamilton原理推导出了梁的控制方程和边界条件。应变能除了考虑经典弹性理论,还要考虑微结构效应和表面能。Navier-type的解析解适用于简支边界条件,而基于拉格朗日插值的微分求积法(DQEM)可以研究在不同边界条件下的力学响应。把该数值解与Navier方法得出的解析解作了对比,得出:微尺度梁在考虑表面能或微尺寸效应、不同载荷和梁高变化下的响应一致;当不考虑微结构相关性和表面能效应时,该模型退化为经典的欧拉梁模型。     

超弹性薄膜与可压缩基底双层结构表面失稳分析

当上层超弹性硬质薄膜和下层可膨胀基底构成的双层结构受压时,薄膜的自由表面可通过形成褶皱降低系统能量.研究表明,上下两层的模量比不同时,上层弹性硬质薄膜将表现出不同的表面失稳模式.本文提出了一种新颖的方法可有效抑制双层软材料的表面失稳,即改变基底材料的泊松比,这种方法同时适用于不具有应变硬化的软材料.首先基于Neo-Hookean模型发展了小变形条件下双层结构表面失稳的理论模型,通过半解析的方法得到了表面失稳的临界应变;然后通过有限元计算与模拟,进一步验证了负泊松比基底可延缓表面失稳.结果表明:(1)当双层结构基底泊松比为正且趋于0.5(不可压缩)时,双层结构在较小的压缩应变下出现表面失稳;(2)当基底的泊松比为负且趋于-1时,可被压缩至46%而不出现表面失稳,即可膨胀基底能有效抑制薄膜的表面失稳.本文发展的方法及主要结果可为延展性电子器件的设计提供指导.     

粉末热压扩散与应力场耦合的力学模型

以弹性接触应力场为初始条件,建立了热压条件下球形颗粒表面扩散与应力场耦合的力学模型. 引入包含表面能项级数形式的应力函数,以描述随时间演化的表面扩散过程及扩散对应力场演化的影响. 而应力场通过改变化学势梯度,又会促进(或阻止)表面扩散结合的进程.利用该模型分析了压力、温度和界面区应力场演化对致密化参数的影响. 比较了满足粘着或非粘着对结合宽度和应力分布的影响,将考虑粘着的弹性接触应力场作为初始条件,分析了弹性变形和表面扩散共同驱动的粉末冶金热压烧结致密化规律.      

线弹簧模型法在含表面裂纹球壳中的应用

本文应用线弹簧模型法,基于Sih.G.C.含二维裂纹球壳理论建立了含表面裂纹球壳的控制方程,采用数值方法选取位移试函数及合理地处理了对偶奇异积分方程使计算大为简化,通过电算实现了计算求解过程,从而获得了球壳表面裂纹前沿各点的应力强度因子之值。 最后将计算结果与考虑“膨胀效应”后的Ncwoun-Raju 解进行了比较,同时研究了曲率因素对表面裂纹线弹性断裂性态的影响。     

小Tabor数分形粗糙表面之间的黏着弹性接触分析

基于粗糙表面的分形描述和适用于小Tabor数微突体的黏着弹性接触理论,采用积分方法建立了小Tabor数分形粗糙表面之间的黏着弹性接触模型,获得弹性接触条件下的真实接触面积和载荷表达式,在此基础上采用单因素分析法分析表面粗糙度和材料性质对分离力的影响.结果表明,当分形维数增加时,粗糙表面单位面积上的微突体数目增加且高度减小,从而导致两表面间的分离力增大;当分形粗糙度参数增大时微突体高度增加,从而导致分离力减小;当材料弹性模量增加时黏着作用减弱,从而减小了分离力,而表面黏着能的增加会使分离力急剧增大.     

基于非局部效应和表面效应的输流碳纳米管稳定性分析

应用非局部黏弹性夹层梁模型分析双参数弹性介质中输送脉动流碳纳米管的稳定性.新模型中同时考虑了由管道内、外壁上的薄表面层引起的表面弹性效应和表面残余应力,经典的欧拉梁模型因此通过引入非局部参数和表面参数得到了改进.用平均法对其控制方程进行求解,得到了管道稳定性区域.数值算例揭示了纳米材料的非局部效应、表面效应及两个弹性介质参数对管道固有频率、临界流速和动态稳定性的复杂影响,结论可为纳米流体机械的结构设计和振动分析提供理论基础.     

Determinations of both length scale and surface elastic parameters for fcc metals

In the present research, a systematical study of trans-scale mechanics theory is performed. The surface/interface energy density varying with material deformation is considered, and the general surface/interface elastic constitutive equations are derived. New methods to determine the material length scale parameter and the surface elastic parameters based on a simple quasi-continuum method, i.e. the Cauchy–Born rule, are developed and applied to typical fcc metals. In the present research, the material length parameters will be determined through an equivalent condition of the strain energy density calculated by adopting the strain gradient theory and by adopting the Cauchy–Born rule, respectively. Based on the surface constitutive equations obtained in the present research, the surface elastic parameters are calculated by using the Gibbs definition of surface energy density and the Cauchy–Born rule method.     

基于非局部效应和表面效应的输流碳纳米管稳定性分析简

应用非局部黏弹性夹层梁模型分析双参数弹性介质中输送脉动流碳纳米管的稳定性. 新模型中同时考虑了由管道内、外壁上的薄表面层引起的表面弹性效应和表面残余应力，经典的欧拉梁模型因此通过引入非局部参数和表面参数得到了改进. 用平均法对其控制方程进行求解，得到了管道稳定性区域. 数值算例揭示了纳米材料的非局部效应、表面效应及两个弹性介质参数对管道固有频率、临界流速和动态稳定性的复杂影响，结论可为纳米流体机械的结构设计和振动分析提供理论基础.     

LARGE DEFLECTION THEORY OF NANOBEAMS

One-dimensional nanostructured materials are often used as beams in many applications such as ultrahigh-frequency resonators and ultrasensitive sensors. Compared with usual macroscopic beams, nanobeams have much higher surface/volume ratios so that their surface energies may play a significant role. Besides, they often bear large deflections due to their typically large slenderness ratios and larger elastic ranges. There is, however, lack of a theory that takes into account of both the above two features owned by nanobeams. In this paper, we present such a theory and give applied examples to show that surface energy and large deflection may individually or jointly have notable effects.     

SURFACE STRESS EFFECT IN MECHANICS OF NANOSTRUCTURED MATERIALS

This review article summarizes the advances in the surface stress effect in mechanics of nanostructured elements,including nanoparticles,nanowires,nanobeams,and nanofilms,and heterogeneous materials containing nanoscale inhomogeneities.It begins with the fundamental formulations of surface mechanics of solids,including the definition of surface stress as a surface excess quantity,the surface constitutive relations,and the surface equilibrium equations.Then,it depicts some theoretical and experimental studies of the mechanical properties of nanostructured elements,as well as the static and dynamic behaviour of cantilever sensors caused by the surface stress which is influenced by adsorption.Afterwards,the article gives a summary of the analytical elasto-static and dynamic solutions of a single as well as multiple inhomogeneities embedded in a matrix with the interface stress prevailing.The effect of surface elasticity on the diffraction of elastic waves is elucidated.Due to the difficulties in the analytical solution of inhomogeneities of complex shapes and configurations,finite element approaches have been developed for heterogeneous materials with the surface stress.Surface stress and surface energy are inherently related to crack propagation and the stress field in the vicinity of crack tips.The solutions of crack problems taking into account surface stress effects are also included.Predicting the effective elastic and plastic responses of heterogeneous materials while taking into account surface and interface stresses has received much attention.The advances in this topic are inevitably delineated.Mechanics of rough surfaces appears to deserve special attention due to its theoretical and practical implications.Some most recent work is reviewed.Finally,some challenges are pointed out.They include the characterization of surfaces and interfaces of real nanomaterials,experimental measurements and verification of mechanical parameters of complex surfaces,and the effects of the physical and chemical processes on the surface properties,etc.     

An inclined surface crack subject to biaxial loading

The elastic–plastic stress fields and mode mixity parameters for semi-elliptical surface cracks on biaxial loaded plates have been investigated using detailed three-dimensional finite element calculations. Different degrees of mode mixity are given by combinations of the far-field stress level, biaxial stress ratio and inclined crack angle. These analyses were performed for different surface flaw geometries to study the combined load biaxiality and mode mixity effects on the crack-front stress fields and the size and shape of the plastic zones. It is clear from considering the local stress distributions along the crack front that the elastic crack tip singularities have been derived for several particular cases of mixed mode biaxial loading. By theoretical analysis, the new formulae have been introduced for both the elastic and plastic mode-mixity parameters, accounting for ratios between the I/II, II/III and III/I modes. Particular attention was paid to the strong variations of the mode-mixity parameters along the semi-elliptical surface crack front. The mixed-mode behavior of the crack growth direction angle along the semi-elliptical crack front for different combinations of biaxial loading and inclination crack angles was also determined. It was done using methods based on the maximum tangential stress and the strain energy density criteria.     

平行于功能梯度材料夹层的币型裂纹起裂条件

分析了功能梯度材料中币型裂纹的扩展问题．裂纹平行于无限域中功能梯度材料夹层,受有与裂纹面成任意角度的拉应力．假定功能梯度材料夹层与两个半无限域均匀介质完全粘合,其弹性模量沿厚度方向变化．采用基于层状材料广义Kelvin基本解的边界元方法分析裂纹问题,给出了均布正应力和剪应力作用下裂纹的应力强度因子、将应力强度因子耦合于应变能密度断裂判据,讨论了裂纹体在拉伸应力作用下的起裂条件．     

MECHANISMS UNDERLYING TWO KINDS OF SURFACE EFFECTS ON ELASTIC CONSTANTS

Recently, people are confused with two opposite variations of elastic modulus with decreasing size of nano scale sample： elastic modulus either decreases or increases with decreasing sample size. In this paper, based on intermolecular potentials and a one dimensional model, we provide a unified understanding of the two opposite size effects. Firstly, we analyzed the microstructural variation near the surface of an fcc nanofilm based on the Lennard-Jones potential. It is found that the atomic lattice near the surface becomes looser in comparison with the bulk, indicating that atoms in the bulk are located at the balance of repulsive forces, and the elastic moduli decrease with the decreasing thickness of the film accordingly. In addition, the decrease in moduli should be attributed to both the looser surface layer and smaller coordination number of surface atoms. Furthermore, it is found that both looser and tighter lattice near the surface can appear for a general pair potential and the governing mechanism should be attributed to the surplus of the nearest force to all other long range interactions in the pair potential. Surprisingly, the surplus can be simply expressed by a sum of the long range interactions and the sum being positive or negative determines the looser or tighter lattice near surface respectively. To justify this concept, we examined ZnO in terms of Buckingham potential with long range Coulomb interactions. It is found that compared to its bulk lattice, the ZnO lattice near the surface becomes tighter, indicating the atoms in the bulk are located at the balance of attractive forces, owing to the long range Coulomb interaction. Correspondingly, the elastic modulus of one-dimensional ZnO chain increases with decreasing size. Finally, a kind of many-body potential for Cu was examined. In this case, the surface layer becomes tighter than the bulk and the modulus increases with deceasing size, owing to the long range repulsive pair interaction, as well as the cohesive many-body interaction caused by the electron redistribution.     

An energy-based anisotropic yield criterion for cellular solids and validation by biaxial FE simulations

The initial yield surface of 2D lattice materials is investigated under biaxial loading using finite element analyses as well as by analytical means. The sensitivity of initial yield surface to the dominant deformation mode is explored by using both low- and high-connectivity topologies whose dominant deformation mode is either local bending or strut stretching, respectively. The effect of microstructural irregularity on the initial yield surface is also examined for both topologies. A pressure-dependent anisotropic yield criterion, which is based on total elastic strain energy density, is proposed for 2D lattice structures, which can be easily extended for application to 3D cellular solids. Proposed criterion uses elastic constants and yield strengths under uniaxial loading, and does not rely on any arbitrary parameter. The analytical framework developed allows the introduction of new scalar measures of characteristic stresses and strains that are capable of representing the elastic response of anisotropic materials with a single elastic master line under multiaxial loading.     

Multiaxial yield surface of transversely isotropic foams: Part I—Modeling

A new yield criterion is proposed for transversely isotropic solid foams. Its derivation is based on the hypothesis that the yielding in foams is driven by the total strain energy density, rather than a completely phenomenological approach. This allows defining the yield surface with minimal number of parameters and does not require complex experiments. The general framework used leads to the introduction of new scalar measures of stress and strain (characteristic stress and strain) for transversely isotropic foams. Furthermore, the central hypothesis that the total strain energy density drives yielding in foams ascribes to the characteristic stress an analogous role of von Mises stress in metal plasticity. Unlike the overwhelming majority of yield models in literature the proposed model recognizes the tension–compression difference in yield behavior of foams through a linear mean stress term. Predictions of the proposed yield model are in excellent agreement with the results of uniaxial, biaxial and triaxial FE analyses implemented on both isotropic and transversely isotropic Kelvin foam models.     

基于反求的医疗辅助弹性护具应变能的计算

提出了基于反求工程的医疗辅助弹性护具的设计方法,推导出弹性护具应变能的计算公 式. 设计中应用网格简化技术减少扫描数据以及参数化技术将三维转化为二维进行计算,减 少了网格点应变能的计算量,提高了设计效率. 应用应变能密度函数建立起弹性护具几何尺 寸与应变能之间的关系,为医生或患者科学地选择医疗护具提供了依据.