Structure and molecular conformation of tussah silk fibroin films treated with water–methanol solutions: Dynamic mechanical and thermomechanical behavior

The thermal response of tussah (Antheraea pernyi) silk fibroin films treated with different water–methanol solutions at 20°C was studied by means of dynamic mechanical (DMA) and thermomechanical (TMA) analyses as a function of methanol concentration and treatment time. The DMA curves of α-helix films (treated with ≥80% v/v methanol for 2 min and 100% methanol for 30 min) showed the sharp fall of storage modulus at about 190°C, and the loss peak in the range 207–213°C. The TMA curves were characterized by a thermal shrinkage at 209–211°C, immediately followed by an abrupt extension leading to film failure. Both storage and loss modulus curves significantly shifted upwards for β-sheet films, obtained by treatment with ≤60% methanol for 30 min. The loss peak exhibited a maximum at 236°C. Accordingly, the TMA shrinkage at above 200°C disappeared. The films broke beyond 330°C, failure being preceded by a broad contraction step. Intermediate DMA and TMA patterns were observed for the other solvent-treated films. The loss peak shifted to higher temperature (219–220°C), and a minor loss modulus component appeared at about 230°C. This coincided with the onset of a plateau region in the storage modulus curve. The TMA extension–contraction events in the range 200–300°C weakened, and the samples displayed a final broad contraction (peak temperature 326–338°C) before breaking. The DMA and TMA response of these films was attributed to partial annealing by solvent treatment, which resulted in the formation of nuclei of β-sheet crystallization within the film matrix. The increased thermal stability was probably due to the small β-sheet crystals formed, which acted as high-strength junctions between adjacent random coil and α-helix domains. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2717–2724, 1998     

Structure and molecular conformation of tussah silk fibroin films: Effect of heat treatment

Structural changes of tussah (Antheraea pernyi) silk fibroin films induced by heat treatment were studied as a function of the treatment temperature in the range 200–250°C. The DSC curve of tussah films with α-helix molecular conformation displayed characteristic endo and exo peaks at 216 and 226°C, respectively. These peaks first weakened and then completely disappeared after heating at 230°C. Accordingly, the TMA thermal shrinkage at 206°C disappeared when the films were heated at 230°C. The onset of weight loss was monitored at 210°C by means of TG measurements. X-ray diffraction profiles gradually changed from α-helix to β-sheet crystalline structure as the treatment temperature increased from 200 to 250°C. On raising the heating temperature above 200°C, the intensity of IR and Raman bands characteristic of β-sheet conformation increased in the whole ranges of amide and skeletal modes. The sample treated at 200°C showed a spectral pattern intermediate between α-helix and β-sheet molecular conformation. The IR marker band for random coil structure, still detectable at 200°C, disappeared at higher treatment temperatures. Spectral changes attributable to the onset of thermal degradation appeared at 230°C. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 841–847, 1997     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Structural changes induced in tussah silk (Antheraea pernyi) fibroin films by immersion in methanol

The crystalline transition induced by immersion in a methanol/water mixture of tussah silk fibroin (from Antheraea pernyi) film obtained by casting from a 1% solution was studied by x-ray diffraction, differential scanning calorimetry, and infrared spectroscopy. The molecular conformation of the fibroin, consisting mostly of the α-helix and random-coil forms, was transformed into a random-coil and β-rich conformation containing only a small amount of α-helix after immersion for no more than 5 min. The intersheet packing of the β-crystal of the original tussah silk fibroin film was imperfect in the early stage of immersion. However, crystallization proceeded further when the immersion time exceeded 10 min. As a result the sheets in the β-form crystal became closely packed because of the decrease in the content of the random-coil form. The exothermic peak, which appeared at 226°C in the original fibroin and was attributed to the random-coil → β-structure transition, disappeared completely after immersion for 5 min.     

Physical and chemical properties of tussah silk fibroin films

Physical and chemical structure, as well as thermal behavior of solution-cast regenerated films, prepared from tussah (Antheraea pernyi) silk fibroin, were compared with those of solution-cast native films, in order to ascertain whether treatment (degumming, dissolution) used for preparation affected their properties. Regenerated fibroin films exhibited a higher thermal stability than native ones, as shown by differential scanning calorimetry, thermomechanical analysis, and dynamic mechanical behavior. Glass transition temperature and other relevant thermal transitions of the regenerated silk specimen shifted to higher temperatures compared with those of native specimen. Molecular conformation and crystalline structure did not show significant differences between the two kinds of silk films. Amino acid composition and molecular weight, however, distribution changed markedly after dissolving tussah silk fibroin fiber in concentrated LiSCN in polypeptide size was the main features for the regenerated silk fibroin. © 1994 John Wiley & Sons, Inc.     

Porous 3‐D scaffolds from regenerated Antheraea pernyi silk fibroin

In this study, porous three‐dimensional (3‐D) materials were prepared with the regenerated Antheraea pernyi (A. pernyi) silk fibroin by freeze‐drying from a lithium thiocyanate solution of its fibers. The relationship between preparation conditions and morphological structures of 3‐D materials was also studied. We concluded that with the decrease in A. pernyi silk fibroin solution concentration and the increase in the freezing temperature, the porosity and the average pore diameter of the 3‐D materials were increased while the pore density was decreased. By adjusting the freezing temperature and the silk fibroin solution concentration, the 3‐D materials having the average pore diameter of 75–260 µm and the porosity of 70–90% can efficiently be produced. As a kind of new material with excellent biocompatibility and bioactivity, the material is expected to be applied to tissue regeneration scaffolds. Copyright © 2007 John Wiley & Sons, Ltd.     

Salt-catalyzed addition reaction of monoepoxides with philosamia cynthia ricini and bombyx mori silk fibroins

The heterogeneous addition reaction of various monoepoxides with silk fibroins of Philosamia cynthia ricini and Bombyx mori was investigated at 45–75°C by use of aqueous solutions of various salts as padding catalysts. The effects of salt on the epoxide–silk fibroin reactions were attributed mainly to the nucleophilicity of the anions and also to the acidity or the electronegativity of the cations. The effect of the substituent of the epoxide on the add-ons was elucidated by the modified Taft equation, (log W ? log W₀)/σ* = ρ_p + ρ_sE_s/σ*, where W₀ and W are the add-ons for the reaction of a given compound and of its substituted derivatives, σ* and E_s are the polar and the steric substituent constants, ρ_p and ρ_s are the polar and the steric reaction constants, respectively. Histidine, lysine, arginine, tyrosine, serine, and acidic amino acids were found to react. The reactivity difference between Philosamia cynthia ricini and Bombyx mori fibroins towards the epoxide was discussed in the light of the observed phenomena.     

1H pulsed NMR study of bombyx mori silk fibroin: Dynamics of fibroin and of absorbed water

The dynamical behavior of the Bombyx mori silk fibroin chain and of absorbed water in silk fiber, film, and powder has been studied by ¹H pulsed nuclear magnetic resonance (NMR). Segmental motions do not occur and only the rapid rotation of the methyl groups of alanine residues is observed from ?120 to 130°C. This is independent of the conformation or form of the silk fibroin samples. Magnetization of dry silk fibroin by the solid-echo method shows a single Gaussian decay, while two components are observed in the solid-echo signals of films containing 6–10 w/w% water. An immobile component with a T₂ value of 11 μs is attributed to silk fibroin, and the mobile component to bound water. The T₂ of the latter varies from 50 to 200 μs, depending on the sample. The dynamical behavior of water trapped in the film is discussed on the basis of these T₂ values.     

Conformational Transformation Exhibited by the Peptide Extracted from Crystalline Region of Bombyx mori Silk Fibroin in Solid and Solution States

The conformational transformation of a 30-residue peptide H（Ala-Gly-Ser-Gly-AIa-Gly）5OH, i.e., （AGSGAG）5, extracted from highly crystalline region of Bombyx mori （B. mori） silk fibroin was described by using the high resolution solid state 13^C NMR, and CD spectroscopies. Based on the conformation-dependent 13^C NMR chemical shifts of the Ala, Gly and Ser residues and the line-shape analysis of the conformation sensitive Ala Cβ resonance, the peptide revealed a strong preference for silk Ⅱ structural form, i,e,, an antiparallel fl-sheet structure （φ= - 140±20°and ψ= 135±20°） in solid state. On the contrary, the CD spectra of this peptide in the two non-native hexafluorinated fibre spinning solvents, hexafluoroisopropanol （HFIP） and hexafluoroacetone （HFA）, exhibited the existence of an unusual tightly-folded conformation resembling 310-helix （φ=- 60±20° and ψ=-30±20°）, as judged from the R ratio of [θ]222/[θ]203 in HFIP solution, whereas a dynamically averaged unordered structure in HFA, Taken together, the information inclined to hypothesis that the primary structure of the highly crystalline regions of B. mori silk fibroin may be easily accessible to the large conformational changes, which in turn may be critical for facilitating the structural transformation from unprocessed silk fibroin （silk I form） to processed silk fiber （silk Ⅱform）.     

Chinese Oak Tasar Silkworm Antheraea pernyi Silk Proteins: Current Strategies and Future Perspectives for Biomedical Applications

Chinese nonmulberry temperate oak tasar/tussah, Antheraea pernyi (Ap) silk is a natural biopolymer that has attracted considerable attention as a biomaterial. The proteinaceous components of Ap silk proteins, namely fibroin and sericin may represent an alternative over mulberry Bombyx mori silk proteins. In fact, the silk fibroin (SF) of Ap is rich in Arginyl‐Glycyl‐Aspartic acid (RGD) peptides, which facilitate the adhesion and proliferation of various cell types. The possibility of processing Ap silk proteins into different distinct 2D‐ and 3D‐based matrices is described in earlier studies, such as membranes, nanofibers, scaffolds, and micro/nanoparticles, contributing to a different rate of degradation, mechanical properties, and biological performance useful for various biomedical applications. This review summarizes the current advances and developments on nonmulberry Chinese oak tasar silk protein (fibroin and sericin)‐based biomaterials and their potential uses in tissue engineering, regenerative medicine, and therapeutic delivery strategies.     

Atomic force microscopy: Bombyx mori silk fibroin molecules and their higher order structure

We performed atomic force microscopy measurements on fibroin molecules from the domestic silkworm, Bombyx mori. At low concentrations, we could observe single protein molecules. The shape of the observed molecules is a rod with long smaller chains extending from the ends. The size of the rod is 60 nm in length and 15 nm in width. At high concentrations, we observed long threadlike aggregates of fibroin molecules, their chains entangled with one another. These results provide insight into the microscopic mechanism of silk‐fiber formation. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1436–1439, 2000     

Influence of the draw ratio on the tensile and fracture behavior of NMMO regenerated silk fibers

The tensile properties and fracture surfaces of N‐methylmorpholine‐N‐oxide (NMMO) regenerated silk fibroin fibers produced with a range of draw ratios has been characterized and related to their microstructure with data obtained from Raman spectroscopy and birefringence measurements. The spinning process allows control of two different draw ratios, coagulation, and postspinning, and it has been found that the microstructure and the properties of the fibers can be modified by the proper combination of both draw ratios. NMMO regenerated silk fibroin fibers subjected to postspinning drawing yield tensile properties comparable to other regenerated fibers and strain at breaking comparable to natural Bombyx mori silk fibers. Tensile strength; however, is still significantly lower than that of natural fibers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2568–2579, 2007     

Physical properties and structure of silk. V. Thermal behavior of silk fibroin in the random-coil conformation

The thermal behavior of films of amorphous silk fibroin in the random-coil conformation has been investigated in the temperature range 25–220°C by differential scanning calorimetry (DSC), thermal expansion, dynamic mechanical measurements, x-ray diffraction, and infrared spectroscopy. As the temperature is raised, water is lost up to about 100°C. Intramolecular and intermolecular hydrogen bonds are broken between 150 and 180°C. The glass transition is observed at 173°C by DSC. The random-coil→β-form transition accompanied by reformation of hydrogen bonds takes place above 180°C. Thermally induced crystallization to the β-form crystals starts at about 190°C.     

甘油对丝素蛋白膜水溶性和结构的影响

探讨了甘油的加入对丝素蛋白溶解过程的结晶结构及结晶度的影响. 以甘油为添加剂用流延法于室温制备一系列丝素共混膜, 测试了其含水率、溶失率及结构和机械性能. 结果表明, 随着甘油加入量的增加, 丝素蛋白的溶失率逐渐降低; 当甘油/丝素质量分数超过10%时, 共混膜呈现水不溶性. 当甘油加入量较少时, 丝素蛋白呈现少量的Silk Ⅱ结晶, 而Silk Ⅰ结构不明显. 随着甘油含量的不断增加, Silk Ⅰ结晶逐渐增加而Silk Ⅱ结晶逐渐减少. 当甘油加入量达到不溶点(10%)时, 丝素蛋白主要转变为Silk Ⅰ结晶, 而几乎没有Silk Ⅱ结晶. 甘油的加入可使共混膜的柔韧性显著提高, 并促使丝素蛋白结晶度提高以及促使丝素蛋白向Silk Ⅰ结晶转变, 从而降低丝素蛋白膜的水溶性.     

The effect of water on the conformation transition of Bombyx mori silk fibroin

Near-infrared spectroscopy (NIR) and differential scanning calorimetry (DSC) were used to investigate temperature-induced changes in the secondary structure and hydration of reconstituted Bombyx mori silk fibroin, with and without freezing water, by looking at regenerated silk fibroin films with a range of water content. We suggest that freezing water facilitates the movement of peptide chains and thus contributes to the conformational transition at 60 °C. The structural changes during heat treatment were analyzed by the two-dimensional correlation method. It was found that the band at 4600 cm⁻¹ consists of complex overlapping components due to different secondary structure elements which compose the protein architecture. Thus, this band could be used as a sensitive probe to estimate the conformations of silk fibroin. By monitoring the variations of the spectral components dynamically, an NIR procedure for tracking the conformational transition of silk fibroin was established.     

Structure and molecular conformation of tussah silk fibroin films: Effect of methanol

Structural changes of tussah (Antheraea pernyi) silk fibroin films treated with different water-methanol solutions at 20°C were studied as a function of methanol concentration and immersion time. X-ray diffraction measurements showed that the α-helix structure, typical of untreated tussah films, did not change for short immersion times (2 min), regardless of methanol concentration. However, crystallization to β-sheet structure was observed following immersion of tussah films for 30 min in methanol solutions ranging from 20 to 60% (v/v). IR spectra of tussah films untreated and methanol treated for 2 min exhibited strong absorption bands at 1265, 892, and 622 cm^?1, typical of the α-helix conformation. The intensity of the bands assigned to the β-sheet conformation (1245, 965, and 698 cm^?1) increased for the sample treated with 40% methanol for 30 min. Raman spectra of tussah films with α-helix molecular conformation exhibited strong bands at 1657 (amide I), 1263 (amide III), 1106, 908, 530, and 376 cm^?1. Following α → β conformational transition, amide I and III bands shifted to 1668, and to 1241, 1230 cm^?1, respectively. The band at 1106 cm^?1 disappeared and new bands appeared at 1095 and 1073 cm^?1, whereas the intensity of the bands at 530 and 376 cm^?1 decreased significantly. ©1995 John Wiley & Sons, Inc.     

Controlling molecular conformation of regenerated wild silk fibroin by aqueous ethanol treatment

Regenerated Antheraea pernyi silk fibroin film was prepared by dissolution of native silk fiber in aqueous lithium thiocyanate. The influence of aqueous ethanol treatment of the dried regenerated film on molecular conformation was studied by X‐ray diffraction, infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. While the initial regenerated film consisted of α‐helix and random coil components, aqueous ethanol treatment of the film resulted in significant increase in β‐sheet component and improvement of water resistance of the film. This effect was strongly dependent on ethanol concentration, and 40–60% (w/w) ethanol was most effective due to balance of hydrophilic/hydrophobic action of the solvent. Copyright © 2003 John Wiley & Sons, Ltd.     

Physical properties and structure of silk. II. Dynamic mechanical and dielectric properties of silk fibroin

Dynamic mechanical and dielectric properties of amorphous regenerated films of silk fibroin were studied as a function of temperature. A mechanical loss tangent peak at about 175°C may be due to the segmental motion of the main chains in the amorphous silk fibroin film. The dynamic modulus of the amorphous silk fibroin increased at 185°C due to the crystallization of the silk fibroin. Dielectric loss tangent peaks were observed at about ?40°C and 175°C at 1 kHz. The former is ascribed to the local motion of the amorphous silk fibroin with absorbed water, while the latter seems to originate from the segmental motion of the main chains and the crystallization of silk fibroin.     

Novel regular network polyester films from aromatic tetracarboxylic acids and ethylene glycol

Novel regular network polyester films were prepared from pyromellitic (X), biphenyltetracarboxylic (U), and 3,3′,4,4′-benzophenonetetracarboxylic (W) dianhydrides and ethylene glycol (2G). Prepolymers prepared by melt polycondensation were cast from DMF solution and successively post-polymerized at 260°C for various times to form a network. The resultant films were transparent, flexible, and insoluble in any solvents. The structure and properties of these network polyester films were compared with those of previously reported network polyester film from trimesic acid (Y) and 2G. Two diffraction peaks appeared in X-ray diffraction curves of 2GY, 2GX, and 2GU films. Peaks of 2GX and 2GU were broader than that of 2GY, suggesting less ordered structure of 2GX and 2GU by the less symmetric aromatic tetracarboxylic acid moieties. Densities of network films decreased with increasing the post-polymerization time. The degree of reaction (the degree of network formation) was estimated by the change of infrared absorption of hydroxyl and methylene groups. The degree of reaction obtained was 95 and 87% for 2GY and 2GX films post-polymerized for 12 h, respectively. Distortion temperature (T_h) was measured by a penetration mode of thermomechanical analysis (TMA). T_h, was 222 and 240°C for 2GY and 2GW films post-polymerized at 260°C for 12 h, respectively, while it disappeared for 2GX and 2GU films post-polymerized for more than 30 min and 1 h, respectively. Drastic decrease in TMA curves around 400°C corresponded to the rapid weight loss in TG curves due to the thermal decomposition. Young's modulus of network film was 2GX > 2GW = 2GU > 2GY, while the tensile strength and elongation were 2GY > 2GU > 2GW > 2GX. Water absorbing capacity was 2GX > 2GY > undrawn PET, while the alkali resistance was undrawn PET = 2GY > 2GX.     

Compound Finishing of Bombyx mori Silk: A Study of Cold Oxygen Plasma/Titania Sols Treatments and Their Influences on Fiber Structure and Performance

Degummed Bombyx mori (B. mori) silk fabrics modified by cold oxygen plasma (COP) and/or titania sols (TSs) were investigated by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction, field emission scan electronic microscopy (FE-SEM), thermo-gravimetric and differential thermal analysis, and ultraviolet (UV) transmittance methods in this study. FT-IR analysis demonstrated that titania particles were associated with B. mori silk fibers by forming organic?Cinorganic hybrid blends. Processing sequences of COP and TSs, and curing conditions showed significant impacts on the crystalline, thermal, micro-morphological, and UV resistant characteristics of silk fabrics. Crystallinity index by both area and height methods, and crystallite sizes of silk fabrics were calculated as well. Results showed that crystallinity index of finished samples approximate to that of degummed silk fabric could be obtained by applying TSs and curing at 160?°C for 2?min prior to COP treatment, or vice versa with lower temperature of 140?°C for 3?min, whereas the crystallite sizes of treated samples increased slightly. The initial decomposition temperatures of finished samples were elevated by 23?C35?°C with increased char residues at 600?°C, while the transmittance of UVA and UVB of finished samples decreased by 11.7, 17.7%, respectively. FE-SEM analysis revealed that titania particles were associated on the fiber surfaces with different smoothness.