钙处理对AH36船体钢耐点蚀性能的影响

为提高AH36钢的耐海水腐蚀性能,炼钢时引入了钢水钙处理工艺.本文通过室内间浸挂片试验、交流阻抗试验、动电位极化试验及极化试验后的SEM分析,研究了钙处理对AH36钢中的夹杂物及耐点蚀性能的影响.结果表明:变性夹杂物中的CaS对钙处理钢的耐点蚀性能有明显的影响.通过钙处理把钢中氧化铝夹杂、硅铝酸盐夹杂等球化变性成无CaS或低CaS的球状CaO-Al2O3复合夹杂,可有效提高钢的耐点蚀性能;变性球状复合夹杂中含较多的CaS会促进诱发夹杂物周围基体腐蚀,提高点蚀诱发敏感性;含硫量较高的AH36钢在钙处理不充分时,形成CaS夹杂或以CaS为主的复合夹杂,会使AH36钢的耐点蚀性能恶化.     

Study on corrosion simulation device for marine structural steel

A corrosion simulation device was studied using offshore long scale hanging specimens. An Ni-Cu-P steel specimen was studied by analysing its corrosion products and corrosion types. The appearance of the samples and the surface of the metallic substrate after the removal of the rust layer produced by these two methods were observed and compared after 470 days of exposure. The phase structure of the corrosion products under different marine environments were analysed and compared. It further indicated good correlation between the electrically connected hanging specimen method and the long scale hanging specimen method.     

Effect of pulsed electric current treatment on corrosion of structural metals

Results of corrosion tests of structural metals previously treated using pulsed electric current of high density are presented. According to the data obtained, the treatment substantially affects corrosion of metals. In cases of HSLA steel and 5182 aluminum alloy, an increase of corrosion resistance occurs, whereas the same treatment causes a dramatic reduction of corrosion resistance of 5754 aluminum alloy. Translated from Problemy Prochnosti, No. 4, pp. 62–68, July–August, 2009.     

Effect of microstructure on KCl corrosion attack of modified AISI 310 steel

Abstract

The effect of microstructure on KCl corrosion attack was studied using a specifically chosen modified AISI 310 austenitic steel in a 15% (v/v) H₂O (g) + 5%(v/v) O₂ (g) + N₂ (g) (balance) atmosphere at 600°C for 168 h. The material was a targeted choice as it allows investigation of different microstructures i.e. as-received (without sigma phase) and heat-treated (29% σ-phase per area) microstructures. The corrosion attack was studied with light optical, scanning electron and transmission electron microscopy as well as X-ray diffraction. The heat-treated sample showed a corrosion attack that was 5 times higher than the as-received sample. In the heat-treated sample, the σ-phase was selectively attacked. At the corrosion front, chlorine (but not potassium) was detected in the selectively attacked σ- phase but not in the unattacked adjacent matrix. Therefore, the corrosion attack was propagated by preferential σ-phase attack by chlorine species.     

Pitting corrosion of 2Cr13 stainless steel in deep-sea environment

Pitting corrosion of 2Cr13 stainless steel was investigated by deep-sea exposure test at various depths of 500 m,800 m and 1200 m in the South China Sea for 4 months.With the aid of electrochemical measurements in simulated deep-sea environments and grey relational analysis,the influence of deepsea environments on passive film and the mechanism of pitting corrosion were discussed.The results indicated that with the increase of sea depth,pitting depth of 2Cr13 stainless steel increased,which can be attributed to the change of chemical composition and the degradation of pitting resistance of passive film.Film growth was greatly retarded in the condition of low seawater temperature and low dissolved oxygen content of deep sea,resulting in an unstable and vulnerable film.Pitting depth was most influenced by hydrostatic pressure,which can increase the adsorption and penetration of Cl-ion,and promote the proliferation of point defects in passive film,leading to rapid deconstruction of protective oxides of the film.Pitting sensitivity of 2Cr13 stainless steel increased eventually with the combination of accelerated dissolution and suppressed self-healing of passive film in deep sea.     

表面机械研磨处理Fe-C合金腐蚀性能的研究

首先利用表面机械研磨技术(SMAT)使低碳钢实现了表面纳米化,然后通过金相显微镜、X射线衍射仪对SMAT后低碳钢的微观组织结构进行表征,最后通过CS350型电化学工作站测试系统对试样进行测试,分析及比较了低碳钢及其SMAT试样在0.05 mol/L H2SO4+0.05 mol/L Na2SO4介质中的腐蚀行为。实验表明,在SMAT之后,20号钢的耐腐蚀性能好于10号钢,而这恰恰与粗晶状态下10号钢的耐腐蚀性能好于20号钢的结果相反,其原因值得探究。     

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A₃ steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0·12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A₃ and 16 Mn steel in marine environment were in the order: MA>SW>SBS by the IHP method; and MA>SBS>SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.     

Evaluation of hot corrosion resistance of HVOF coatings on a Ni-based superalloy in molten salt environment

High-velocity oxy-fuel (HVOF) has the advantage of being a continuous and most convenient process for applying coatings to industrial installations at site. In this study, Cr₃C₂–NiCr, NiCrBSi, Stellite-6 and Ni–20Cr coatings were deposited on a Ni-based superalloy (19.5Cr–3Fe–0.3Ti–0.1C–balance Ni) using an HVOF process. Hot corrosion studies were performed on bare as well as coated superalloy specimens after exposure to a molten salt environment at 900 °C under cyclic conditions. The thermogravimetric technique was used to establish the kinetics of corrosion. XRD, SEM/EDAX and EPMA techniques were used to analyse the corrosion products. The hot corrosion resistance of all the coatings were superior to bare superalloy. Among the coatings studied, the Ni–20Cr coated superalloy imparted maximum hot corrosion resistance, whereas the Stellite-6 coated indicated minimum resistance. The hot corrosion resistance of all coatings may be attributed to the formation of oxides and spinels of nickel, chromium or cobalt.     

冷却工艺对货油舱用耐蚀钢组织性能的影响

基于货油舱用耐蚀钢的服役环境设计并冶炼了一种新型耐蚀钢,根据试验钢变形奥氏体连续转变曲线,采用控制轧制和控制冷却的技术将锻后110 mm坯料减薄至16 mm。热轧板材的年平均腐蚀速率分布在0.235~0.273 mm/a,小于船级社要求的1 mm/a。利用扫描电镜、透射电镜、拉伸试验机和冲击试验机进行了耐蚀钢的显微结构分析及力学性能研究,探究了控制冷却工艺对耐蚀钢组织性能的影响规律。结果表明:在终冷温度669 ℃、冷却速度8.9 ℃/s的条件下,耐蚀钢显微组织主要为铁素体、贝氏体和退化珠光体。降低终冷温度或提高冷却速率有利于抑制珠光体转变,促进针状铁素体和贝氏体相变进程,增加小角度晶界数量,提高耐蚀钢的组织均匀性和力学性能。当终冷温度降低至597 ℃,冷却速度增大到13.1 ℃/s,耐蚀钢组织为针状铁素体、粒状贝氏体和板条贝氏体混合结构,不均匀分布且粗大尺寸的板条结构弱化了材料的抗冲击性能。     

Analysis of steel structure corrosion of drinking water distribution system in family indoor environment

In this paper, corrosion investigation and analysis of steel structure of drinking water distribution system in a family kitchen have been carried out. Results indicate that galvanized corrosion and condensation corrosion under thin water layer have been found the main corrosion type. XRD analysis shows that the rust layer is composed of α‐FeOOH, γ‐FeOOH and Fe₃O₄. For preventing galvanic corrosion, using non‐conductive materials between metals of different electropotential, i.e. electrically insulating the two metals from each other has been recommended. For preventing condensation corrosion under thin water layer, cleaning the pipe external surface to minimize the condensation corrosion is necessary and a good epoxy coating on the pipe external surface may also work. The selection of PVC pipe with better quality and no leaching of inorganic pollutants into water is also a good choice, however, in this condition strong hitting to the PVC pipe should be avoided.     

Effect of some ethoxylated fatty acids on the corrosion behaviour of mild steel in sulphuric acid solution

The inhibition of the corrosion of mild steel in 1.0 M sulphuric acid solution by some ethoxylated fatty acids OL[EO]₂₀, OL[EO]₄₀ and OL[EO]₈₀ has been studied in relation to the concentration of the inhibitors as well as the temperature using chemical (weight loss) and electrochemical (potentiodynamic polarization) techniques. The inhibition efficiency increases with increasing the concentration and the chain length of the inhibitor but decreases with temperature. The inhibition was assumed to occur via adsorption of the fatty acid molecules on the metal surface. The thermodynamic functions of dissolution and adsorption processes were calculated.     

The influence of the environment and corrosion on the structural integrity of aircraft materials

Fatigue results of 1¹/₂ dog-bone jointed specimens manufactured from 7075-T6 aluminium alloy indicated that the application of corrosion preventative compounds (CPCs) at the faying surfaces slightly decreased the log mean fatigue life at 144 MPa, while the effect was not statistically significant at the higher stress level (210 MPa). The addition of the CPC also reduced fretting corrosion at the faying surfaces and shifted the fatigue initiation sites closer to the edge of fastener holes. Scatter in fatigue life was found to be associated with the location and size of the intermetallics at the initiation site. The presence of corrosion in the bores of the countersunk fastener holes reduced the fatigue life by up to one order of magnitude. Fatigue test results for dog-bone specimens manufactured from 7075-T651 and 2024-T351 aluminium alloys indicated that the presence of exfoliation corrosion reduced the fatigue life under dry conditions, with a greater reduction under humid conditions. The application of a CPC to the corroded region eliminated the influence humidity had on fatigue life.     

High temperature corrosion performance of Q235 steel in sulfur-bearing solution

The high temperature corrosion performance of Q235 steel in sulfur-bearing solutions as a function of temperature, test time, and sulfur content was investigated by weight loss measurements in this study. The results indicate that the corrosion behavior of Q235 steel in sulfur-bearing solution is directly related to the experimental temperature, immersion time and sulfur content. Higher temperature leads to a higher corrosion rate of the steel. The corrosion rate increases during the initial test time and then decreases with increasing the test time. As the sulfur content increases in the solution, the corrosion rate increases, and further increasing the sulfur content leads to a decreased corrosion rate.     

脉冲电流处理对X70管线钢腐蚀性能的影响

测量了X70管线钢在NS4溶液中的极化曲线,研究了高密度脉冲电流处理对其腐蚀性能的影响,结果表明,高密度脉冲电流处理导致X70管线钢的晶粒细化,使其内部活性区减少,提高了管线钢的耐局部腐蚀能力,X70管线钢的耐局部腐蚀能力随着脉冲电流密度的提高而增强,腐蚀产物的分布也更加均匀细密。     

极地钢铁材料的腐蚀与防护面临新挑战

随着极地的开发和利用,其所需的极地钢铁材料的腐蚀与防护问题越来越受到研究者的关注。本文以传统海洋环境腐蚀分区为参照,对极地特色的腐蚀环境进行了系统的分析,并将其归纳整理为极地大气区、极地冰水磨蚀区、极地海洋全浸区、极地海底泥土区等4个腐蚀区域。在对极地钢铁材料腐蚀与防护的研究进展进行梳理的基础上,从合金化、涂层技术和阴极保护技术3个方面介绍了极地钢铁材料的防护技术,并指出了极地钢铁材料未来研究的方向。     

Effect of tin addition on corrosion behavior of a low-alloy steel in simulated costal-industrial atmosphere

The effect of tin addition on the atmospheric corrosion behavior of a low-alloy steel in simulated coastal-industrial atmosphere has been investigated by indoor wet/dry cyclic corrosion test (CCT). The results indicate that tin addition can obviously make the steel substrate more resistant to atmospheric corrosion by suppressing the cathodic H⁺ reduction reaction, and but tin addition is not of obvious beneficial effect when the steel is covered with a thicker rust layer during long-term corrosion process. The reason lies in the fact that the presence of un-reduced H⁺ can lower the electrolyte pH value and lead to a loose and porous rust layer on tin-containing steel sample than that on tin-free steel sample. In addition, the 120 CCT cycles corrosion process of the two steels can be divided into three stages. Both the tin-free and tin-containing steels show an increasing corrosion rate during the initial corrosion stage and then exhibit a decreasing corrosion rate during the second and third corrosion stages. Moreover, tin addition makes the tin-containing steel rust layer have a higher amount of α-FeOOH and lower amount of γ-FeOOH and Fe₃O₄ than the tin-free steel rust layer.     

Microbial corrosion resistance of a novel Cu-bearing pipeline steel

Microbiologically influenced corrosion (MIC) is becoming a serious problem for buried pipelines. Developing environmentally friendly strategies for MIC control is increasingly urgent in oil/gas pipeline industry. Copper (Cu) in steels can not only provide aging precipitation strengthening, but also kill bacterium, offering a special biofunction to steels. Based on the chemical composition of traditional X80 pipeline steel, two Cu-bearing pipeline steels (1% Cu and 2% Cu) were fabricated in this study. The microstructure, mechanical properties and antibacterial property against sulphate-reducing bacteria (SRB) and Pseudomonas aeruginosa (P. aeruginosa) were studied. It was found that the novel pipeline steel alloyed by 1%Cu exhibited acicular ferrite microstructure with nano-sized Cu-rich precipitates distribution in the matrix, resulting in better mechanical properties than the traditional X80 steel, and showed good MIC resistance as well. The pitting corrosion resistance of 1% Cu steel in as-aged condition was significantly better than that of X80 steel. A possible antibacterial mechanism of the Cu-bearing pipeline steel was proposed.     

轧制工艺对316L不锈钢组织和耐蚀性能的影响

为探索改善不锈钢耐腐蚀性能的途径,对316L不锈钢施加相同变形量的同步轧制和异步轧制,利用X射线衍射、透射电镜观察、电化学测量和扫描电镜表面观察研究了轧制工艺对钢的显微组织和腐蚀性能的影响.结果表明,经过异步轧制后显微组织中出现大量孪晶界,优化了晶界结构,在酸性介质中的晶间腐蚀敏感性明显减轻;而经过同步轧制后,样品呈现出高位错密度的显微组织,在酸性介质中的耐腐蚀性能降低.异步轧制后耐蚀性能得到改善是由于大量孪晶界的形成优化了晶界结构.     

S32750双相不锈钢相界与晶界特征对其力学性能和耐蚀性能的影响EI北大核心CSCD

通过固溶处理获得不同初始组织状态的S32750双相不锈钢样品,然后进行厚度压下量80%的冷轧变形和1050℃的退火处理,采用SEM-EBSD和XRD技术研究合金相界与晶界特征以及相组成分布情况,并利用拉伸实验、纳米压痕和双环电化学动电位再活化法(DL-EPR)分析不同初始状态样品的组织对力学性能与耐晶间腐蚀性能的影响规律。结果表明:高温固溶处理的合金样品经冷轧退火后晶粒细小均匀,两相分布接近1∶1,且相界占内界面(晶界+相界)比例较高,同相晶粒团簇程度最低,表现出优异的综合力学性能。合金样品经敏化处理后,σ相易沿α相晶界析出,高温固溶并经轧制退火后的样品中,由于α晶界比例较少且满足K-S取向关系的相界比例较高则又表现出良好的晶间腐蚀抗力。因此,通过适当的工艺来调控合金的相界与晶界分布可以实现材料强度和晶间腐蚀抗力的同步改善。     

金属表面Sol-gel法制备耐腐蚀陶瓷涂层的研究进展

综述了溶胶－凝胶涂层的成膜原理，制备工艺，比较了溶胶－凝胶法与其它金属陶瓷涂层的制备工艺，讨论了溶胶－凝胶涂层对金属耐磨腐蚀性能，耐磨性能的改进及在腐蚀防护领域中的应用，还对溶胶－凝胶涂层技术的发展的提出了看法。