纳米氧化铈的制备及其抛光性能的研究

采用溶胶-凝胶法制备了纳米CeO2粉体,并采用XRD、TOF-SIMS对其进行了表征。结果表明平均晶粒度在13.3nm,粒度分布均匀。进而研究了纳米CeO2在玻璃基片抛光中的抛光性能。ZYGO形貌仪表明,抛光后其表面平均粗糙度值(Ra)可降低到0.6nm左右。原子力显微镜(AFM)在5μm×5μm范围内测得基片表面粗糙度Ra值为0.281nm,表面光滑,划痕等表面微观缺陷明显改善。     

单晶硅化学机械抛光划痕演变研究

化学机械抛光法是制作超光滑单晶硅镜片的常用工艺,抛光过程中的各类杂质粒子经常会导致加工表面产生划痕,降低镜片的表面质量。为系统研究不同晶向单晶硅表面塑性划痕与抛光液中杂质的关系,设计了金刚石微粉掺杂抛光Si(111)、Si(110)和Si(100)晶面的实验。利用轮廓仪测量了不同晶向、不同掺杂浓度下的划痕形貌,并通过计算载荷归一化后的划痕宽度分布、划痕深度分布、粗糙度和二维功率谱密度来评估划痕形貌。结果显示,抛光液中杂质粒子粒径、硅片表面的划痕宽度均服从正态分布。随着杂质粒子浓度的增加,划痕形貌从非周期性特征转变为周期性波动,粗糙度出现突跃点。此外,在同浓度金刚石微粉掺杂情况下,Si(110)面在划痕产生初期有更好的杂质粒子容忍度。     

α型氧化铝的微观结构对红外光谱图的影响

选取不同生产工艺的α-Al2O3样品,用激光粒度仪测试粒度分布,在扫描电镜下观察α-Al2O3的微观结构,用X-射线衍射仪测试α-Al2O3相含量,在相同制样条件测试条件下,测试其红处光谱.结果表明:α-Al2O3样品红外光谱图有差异.分析认为生产工艺(煅烧法和电熔法)是影响α-Al2O3谱图差别的主要原因,其次为晶粒微观形貌和大小.     

大面积α-Fe2O3纳米线及纳米带阵列的制备研究

以铁箔为原材料和基片,通过控制热氧化过程中的宏观实验条件(载气流量及其组分、压强、温度分布和反应时间等),实现了α-Fe2O3一维纳米结构的可控生长,获得了大面积(10mm×10mm)、单分散性好、沿[110]方向生长的α-Fe2O3纳米带或纳米线阵列. 对不同宏观实验条件下所制备的样品进行形貌和晶格结构表征和分析,认为热氧化过程中α-Fe2O3一维纳米结构的生长遵循类似气-固机制的顶端生长模式,生长点铁原子和氧原子比是控制α-Fe2O3一维纳米结构生长的关键因素.     

化学气相沉积SiC材料超光滑表面纳米加工

 利用传统光学加工方法，采用陶瓷磨盘和金刚石微粉对国产化学气相沉积(CVD) SiC进行了粗磨、细磨加工；然后，利用颗粒直径从4 μm到1 μm的金刚石研磨膏逐级进行抛光，发现SiC表面存在纳米级划痕；最后，改用颗粒直径为20 nm氧化铝纳米颗粒的碱性水溶液进行抛光，表面粗糙度达到0.6 nm(RMS)，表面纳米级划痕得到很好改善，获得了较高表面质量的超光滑表面。     

Pt/TiO_2复合纳米结构形貌控制及光催化动力学

制备了3种不同形貌的Ti O2结构:纳米杯、(001)纳米片、(100)纳米片,并进一步与Pt纳米粒子复合以去除污水中的有机染料。透射电镜结果证实了3种Ti O2纳米结构的形成,观察到了附着其上的Pt纳米粒子。使用XRD确定了3种Ti O2纳米结构均为锐钛矿相。以罗丹明B作为有机染料,检测了不同形貌Ti O2及其Pt复合物的光催化性能。结果表明:纳米杯状的Pt/Ti O2在罗丹明B溶液中表现出最高降解率,在1.5 h内降解率可达99.1%。同时讨论了Ti O2及其复合物的光降解机理。     

沉淀法制备超细氧化铝粉末过程中的团聚机理和消除办法

采用沉淀法以Al(NO3)3.9H2O和NH3.H2O为原料制备了Al(OH)3干凝胶,经过高温煅烧合成纳米级的α-Al2O3粉末,分析了在制备过程中氧化铝粉末产生团聚的机理,推测了硬团聚的机理模型,并提出了几种消除硬团聚的方法,制备出的α-Al2O3粉末,粒径分布均匀,且无明显团聚,近似球形,平均粒径为70nm。     

倾斜表面的纳秒激光抛光研究

考察倾斜表面纳秒激光抛光后的表面形貌演化规律及表面倾斜程度对抛光效果的影响规律，可以为增材制造中的自由曲面激光抛光提供参考。采用纳秒激光对不垂直于光轴的粗糙平面进行激光抛光，并采用激光共聚焦显微镜对激光抛光后的表面形貌进行测试分析。结果表明：表面倾斜30°时，抛光后的表面在距离起始点4 mm附近存在表面轮廓波动异常增大的现象，表面粗糙度值增大到15.80μm；倾斜角度增大到45°时，表面轮廓波动异常增大的位置变化到2 mm附近；倾斜角度为60°时，未发生表面轮廓波动异常增大现象。表面轮廓波动异常增大现象反映了激光抛光从过熔型抛光到浅熔型抛光的过渡过程；自由曲面的激光抛光工艺需要根据抛光区域的倾斜程度和表面粗糙度选定合适激光功率密度和离焦量，从而实现良好的激光抛光质量。     

准立方体α-Fe_2O_3纳米薄膜的紫外和红外光谱研究

采用浸渍提拉法制备了准立方体α-Fe2O3纳米薄膜,利用XRD、AFM、UV-Vis和FT-IR对其表面形貌和谱学性质进行了表征。结果表明,α-Fe2O3单层膜是由粒径约为58nm的粒子排布而成,在568、482和386cm-1处有特征红外吸收峰,在紫外区375nm处存在明显的吸收,为Fe-O间的电子跃迁,其吸光度值与膜层数间的较好线性关系说明在一定的速度下挂膜,可以将氧化铁溶胶中的纳米粒子较好地转移到基片上。     

Li2O-Al2O3-SiO2微晶玻璃表面粗糙度对纳米硬度测试的影响

 介绍了纳米压痕测试技术的基础理论及纳米压痕法常用的Oliver -Pharr方法的计算原理。采用纳米压痕试验测得不同表面粗糙度的Li2O-Al2O3-SiO2微晶玻璃样品的纳米硬度、弹性模量和载荷-位移曲线。结果表明样品表面粗糙度会降低纳米压痕测试结果的稳定性、准确性和可靠性：样品表面粗糙度越小,测得的纳米硬度和弹性模量值波动越小,载荷-位移曲线重合性越高。随着最大载荷的增大,测得的弹性模量逐渐减小,其原因是压痕边缘材料发生了塑形变形。在超光滑表面样品（Ra=0.9 nm）上测得较为准确的Li2O-Al2O3-SiO2微晶玻璃纳米硬度和弹性模量值分别为8.8 GPa和7.79 GPa。纳米压痕测试结果的重合度对于评价超光滑表面完整性研究具有指导意义。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.