Vortex characteristics in laminar cavity flow at very low Mach number

In the present paper, a laminar cavity is analysed at very low Mach numbers. The characteristics of core-vortices are proposed and commented. The experiments were performed in an open subsonic wind tunnel using particle image velocimetry (PIV). A rectangular cavity with a length-to-depth ratio of 4 was used (shallow and open type). Three different Reynolds numbers, based on cavity depth and free stream velocity, were examined (Re_h=4,000, 9,000 and 13,000). The upstream boundary layer was investigated using classical hot-wire anemometry and was found to be laminar. For each Reynolds number, a total of 1,000 vectors fields were acquired. The results are given in terms of conventional quantities (mean flow velocity, turbulence characteristics, Reynolds shear stress) and also in terms of vortex characteristics (such as probability density function of vortex location, vortex size and vortex circulation). Some of these vortex characteristics are then proposed in a local averaged presentation. The extraction of vortices from instantaneous flow fields has been done through the use of a home-made algorithm based on continuous wavelet analysis.     

The effect of aspect ratio on the flow over a rearward-facing step

In this study, we investigate the effect of the spanwise width on the mixing layer behind a rearward-facing step. Results for aspect ratios (tunnel width/step height) of 10 and 4 and Reynolds numbers of 11,000 and 5,000 are presented. A frequency shifted, single component LDV system was used to obtain mean streamwise velocity profiles, turbulence intensity profiles, and normal velocity spectra at four streamwise and three spanwise positions for each test case. The mean velocity and turbulence intensity profiles are constant across the width of the test section for either of the Reynolds numbers considered, but there are significant differences among the cases studied. At a distance greater than three step heights down-stream of the step, the peak turbulence intensity is greater for higher aspect ratio and is relatively insensitive to Reynolds number. The peak frequency is lower and the spectrum is narrower for a higher aspect ratio in the region near the step.     

Experimental study of flow past a square cylinder at high Reynolds numbers

 Measurements of two-components of velocity in the wake of a square cylinder using a hot-wire anemometer are reported. Two Reynolds numbers, namely 8700 and 17,625, have been considered. The measurements were carried out in a low-speed, low-turbulence wind tunnel. Benchmark experiments at much lower Reynolds numbers show good agreement between the present experiments and published results. At higher Reynolds numbers, the experimental data reveal anticipated trends in terms of wake recovery and turbulence decay. Both velocity and velocity fluctuations show symmetry about the wake axis. The experimental data have been compared with the large eddy simulation (LES) calculation reported by Wang et al. [University of Illinois at Urbana – Champaign (1996) Report CFD 96-03] and LDV measurements of Lyn et al. [J Fluid Mech (1995) 304: 285–319]. The agreement among the three sets is generally acceptable in terms of the time-averaged velocity components, but not the velocity fluctuations. The turbulence fluctuations in the present experiments are seen to be lower than in the referred work. The differences have been traced to factors such as the aspect ratio, blockage ratio and upstream turbulence. Experiments with increased upstream turbulence did show a reduction in the discrepancy between the present experiments and the published data. An assessment of the experimental data in terms of physical mechanisms revealed that (a) streamwise normal stresses were correlated with the vortex centers, and (b) the turbulence kinetic energy profiles are similar to the turbulence shear stress. Spectral analysis of the velocity signals was carried out in the present work. Energy transfer from the mean flow to the streamwise velocity fluctuation was confirmed in the near wake. A redistribution of the kinetic energy between the streamwise and transverse components of velocity over a longer distance downstream was subsequently observed. Received: 17 May 1999/Accepted: 29 December 1999     

Turbulence manipulation in air–water flows on a stepped chute: An experimental study

In a stepped channel operating with large flow rates, the flow skims over the pseudo-bottom formed by the step edges as a coherent stream. Intense three-dimensional recirculation is maintained by shear stress transmission from the mainstream to the step cavities, while significant free-surface aeration takes place. The interactions between free-surface aeration and cavity recirculation are investigated herein with seven step cavity configurations. The experiments were conducted in a large stepped channel operating at large Reynolds numbers. For some experiments, triangular vanes, or longitudinal ribs, were placed across the step cavities to manipulate the flow turbulence to enhance the interactions between the mainstream flow and the cavity recirculation region. The results showed a strong influence of the vanes on the air–water flow properties in both free-stream and cavity flows. The findings demonstrate some passive turbulence manipulation in highly turbulent air–water flows.     

狭缝射流撞击圆柱表面的湍流特性实验研究

实验研究了狭缝射流撞击圆柱表面后壁面射流区的平均流动和湍流特 性. 考察了雷诺数 Re (6000-20000), 喷口到受撞表面距 离 Y/W (5-13), 喷口宽度 W (6.25mm, 9.38mm), 受撞表 面曲率(半圆柱体直径 D = 150mm)对流动和湍流结构的影响. 通过分析 X 热线 在壁面射流区的测量结果发现，在近壁区域，表面曲率、 Re_{w} , Y/W 和 S/W 等 参数对 \sqrt {\overline{u^2}} / U_m 的影响比对 \sqrt {\overline{v^2}} / U_m 强，并且切 应力 \overline {uv} /U_m^2 对表面曲率变化最敏感. 当喷口与受撞击表面之间的距 离 Y/W 在一定范围内增加时， 沿圆柱表面流动的流向和横向的湍流强度增强. 用平板射流和圆柱体表面壁面射流的数据进行比较，从而得到表面曲率对壁面射流特 性的影响. 结果表明，曲率对壁面射流的影响较强， 并随着 S/W 的增大而增强. 随着雷诺数的增大，壁面曲率的影响也有强化的趋势.     

Numerical study of flow and thermal behaviour of lid‐driven flows in cavities of small aspect ratios

Numerical study has been performed to investigate the effects of cavity shape on flow and heat transfer characteristics of the lid‐driven cavity flows. Dependence of flow and thermal behaviour on the aspect ratio of the cavities is also evaluated. Three types of the cross‐sectional shape, namely, circular, triangular, and rectangular, and four aspect ratios, 0.133, 0.207, 0.288, and 0.5, are taken into account to construct twelve possible combinations; however, attention is focused on the small‐aspect‐ratio situations. Value of the Reynolds number considered in this study is varied between 100 and 1800. For the cases considered in this study a major clockwise vortex driven by the moving lid prevailing in the cavity is always observed. When the Reynolds number is fixed, the rectangular cavity produces strongest lid‐driven flow, and the triangular cavity weakest. For the cases at small aspect ratio and low Reynolds number, the streamlines appear symmetric fore‐and‐aft with respect to the central line at x/L = 0.5. Data for the local and average Nusselt numbers are also provided. For rectangular cavities, it is observed that case 1/5R produces the highest average Nusselt number at any Reynolds number. Among the twelve possible geometric cases considered herein, the highest and lowest average Nusselt numbers are found with cases 1/6T and 1/2C, respectively. Copyright © 2006 John Wiley & Sons, Ltd.     

Measurement of the turbulent flow field in a free-surface jet of water

Measurements of the mean velocity and turbulence intensity are presented for a rectangular jet of water ejecting into a gaseous ambient. Data are reported for streamwise locations up to 30 nozzle widths from the discharge and spanwise locations covering the inner 80% of the jet width. The flow conditions at the nozzle discharge were controlled by using different nozzle designs (parallel-plate and converging) and flow manipulators (wire grid and screens). The results track the mean velocity and turbulence intensity profiles with streamwise distance, highlighting changes in both the profile shapes and magnitudes for both measured quantities. Independent of nozzle configuration, the mean velocity profile was shown to be most nonuniform and the turbulence intensity most nonhomogeneous at the nozzle discharge. With increasing streamwise distance, the mean velocity profile underwent a gradual transition to a completely uniform condition, while the turbulence field decayed and became homogeneous. The rate of viscous dissipation was shown to depend strongly on the nozzle exit condition. This work was supported by the National Science Foundation under grant numbers CTS-8912831 and CTS-9307232     

EFFECTS OF LID-DRIVEN CAVITY SHAPE ON THE FLOW ESTABLISHMENT PHASE

Experiments are carried out to study the flow establishment phase inside closed cavities submitted to the impulsive translation from rest, of one of their walls at a Reynolds number of 1000. Three standard industrially machined or molded cylindrical cavity shapes are studied and are compared with respect to the efficiency of mixing process: square, rectangular and semi-circular of length-to-width ratio of 2:1. The flow structures in the mid-cross-section are analysed by means of fine topological and kinematic visualization series using two complementary techniques: continuous dye filament and discrete solid tracers both coupled with a laser sheet illumination. Particular attention is given to vorticity propagation and primary/secondary eddy formations. Although a roughly similar vortex generation is observed in all examined cavities, important differences appear with time. The semi-circular cavity flow results in a much more homogeneous and uniform recirculation with no secondary flow recirculation zone. On the contrary, the square and rectangular cavity flows develop a better flow mass dispersion and, respectively, one and two secondary eddies. At the final time of observation (t^*=12), both semi-circular and rectangular cavity flows seem to reach their steady state whereas the square one continues to evolve. Comparisons with 2-D computational results of other authors illustrate the three-dimensional flow aspect present in experiments.     

The influence of temperature on the measurements of Reynolds stresses in shear free turbulence near a wall

 Temperature changes have a significant influence on the measurements of Reynolds stresses in turbulent boundary layers. As compared to the spanwise velocity fluctuations the streamwise turbulence intensity is especially sensitive to temperature deviations. Although this is a general statement its importance is clearly elucidated in a shear-free turbulence near a solid wall, since the mixing due to turbulence production is minimized in this flow. A consequence of temperature influence on hot-wire measurements is that frictional heating from the wall has produced contradictory results in different experiments on shear-free turbulence. In the current paper, measurements of streamwise and spanwise turbulence intensities have been conducted at different wall temperatures, thereby simulating the contradictory results mentioned above. A simple model has been developed showing that the turbulence intensities are affected by both the rms. value of the temperature fluctuations and the correlation between fluctuating temperature and velocity. These correlations are measured and the developed model is used to explain deviations in earlier measurements on shear-free turbulence. Moreover, the individual magnitudes of the two correlations in the temperature correction are estimated and their individual importance is discussed. Received: 17 February 1997 / Accepted: 18 January 1998     

Measurements of turbulent developing flow in a moderately curved square duct

Laser-Doppler measurements in the turbulent flow in a right-angled bend of square cross-section, radius/duct-width ratio 7.0, are presented and show the development of secondary circulation in cross-stream planes. Distribution of the streamwise and radial components of the mean velocity and turbulence intensity, and the corresponding Reynolds shear stress, are presented as contour plots and are intended for use in the further development of numerical flow prediction methods.     

Measurements in the near flow field of an isosceles triangular turbulent free jet

The near field mean flow and turbulence characteristics of a turbulent jet of air issuing from a sharp-edged isosceles triangular orifice into still air surroundings have been examined experimentally using hot-wire anemometry and a pitot-static tube. For comparison, some measurements were made in an equilateral triangular free jet and in a round free air jet, both of which also issued from sharp-edged orifices. The Reynolds number, based on the orifice equivalent diameter, was 1.84×10⁵ in each jet. The three components of the mean velocity vector, the Reynolds normal and primary shear stresses, the one-dimensional energy spectra of the streamwise fluctuating velocity signals and the mean static pressure were measured. The mean streamwise vorticity, the half-velocity widths, the turbulence kinetic energy and the local shear in the mean streamwise velocity were obtained from the measured data. It was found that near field mixing in the equilateral triangular jet is faster than in the isosceles triangular and round jets. The mean streamwise vorticity field was found to be dominated by counter-rotating pairs of vortices, which influenced mixing and entrainment in the isosceles triangular jet. The one-dimensional energy spectra results indicated the presence of coherent structures in the near field of all three jets and that the equilateral triangular jet was more energetic than the isosceles triangular and round jets.     

Direct simulation of turbulent flow and heat transfer in a channel. Part I: Smooth walls

Interest in the use of supercomputers for the direct numerical calculation of turbulence prompts the development of efficient numerical techniques so that calculation at higher Reynolds numbers might be made. This paper presents an efficient pseudo-spectral technique, similar to but different from others that have recently appeared, for the calculation of momentum and heat transfer to a constant-property, turbulent fluid in a two-dimensional channel with walls at different, uniform temperature. The code uses no empiricism, although periodic boundary conditions are used for fluctuating quantities in the streamwise and spanwise directions. Calculations were made for a Prandtl number of 0·72 and Reynolds number based on friction velocity and channel half-height of 180 or 2800 based on channel half-height and average velocity. Calculations of mean velocity profile, turbulence intensities, skewness, flatness, Reynolds stress and eddy diffusivity of heat near a wall compare favourably with experimental results. Representative contour plots of the temperature field near the wall and of the spanwise and streamwise two-point velocity correlations are given. Deficiencies are that the calculation requires many hours on a fast computer with a large high-speed memory and that the grid size in each direction for appropriate resolution is approximately proportional to the square of the Reynolds number and to the Prandtl number raised to some power greater than one.     

Multiplicity of Steady Two-Dimensional Flows in Two-Sided Lid-Driven Cavities

The two-dimensional steady incompressible flow in rectangular cavities is calculated numerically by a finite volume method. The flow is driven by two opposing cavity side walls which move with constant velocities tangentially to themselves. Depending on the cavity aspect ratio and the two side-wall Reynolds numbers different flow states exist. Their range of existence and the bifurcations between different states are investigated by a continuation method accurately locating the bifurcation points. When both side walls move in opposite directions up to seven solutions are found to exist for the same set of parameters. Three of these are point-symmetric and four are asymmetric with respect to the center of the cavity, if the side-wall Reynolds numbers have the same magnitude. When the walls move in the same direction, up to five different flow states are found. In this case only a single mirror symmetric solution exists for equal Reynolds numbers. Received 9 February 2000 and accepted 9 October 2000     

The near-field characteristics of circular jets at low Reynolds numbers

An experimental study has been undertaken to investigate the effect of Reynolds number on the near-field region of circular turbulent air jets. Measurements were made using a two-component Laser Doppler Anemometer, and included mean velocity, turbulence intensity, skewness factor, flatness factors and power spectrum. Measurements were taken up to 10 nozzle exit diameter in the downstream direction for different exit Reynolds numbers in the range of 1400 to 20000. The Reynolds number was found to have a strong effect on the jet flow behavior in the near-field region; the centerline velocity decays faster (decay constant = 6.11 for Re = 19400, = 1.35 for Re 1430) and the potential core gets shorter with decreasing Reynolds number. Profile measurements of the skewness and flatness factors indicate that the jet flow becomes more intermittent with decreasing Reynolds number. Power spectrum measurements of the streamwise fluctuating velocities reflects the high energy content of the high Reynolds number jet. It also reveals that there is greater energy at the higher frequencies with increasing Reynolds number.     

Turbulent transport dissimilarity with modulated turbulence structure in channel flow of viscoelastic fluid

This experimental study investigated the turbulent transport dissimilarity with a modulated turbulence structure in a channel flow of a viscoelastic fluid using simultaneous particle image velocimetry and planar laser-induced fluorescence measurements. An instantaneous dye concentration field with fluctuating velocity vectors showed that mass was transferred by hierarchically large-scale wavy motions with inclination. A co-spectral analysis showed that the spatial phase modulation of the streamwise velocity and dye concentration fluctuations for the wall-normal velocity fluctuation corresponded to the relaxation time. The occurrence of intense dye concentration fluctuation and small streamwise velocity fluctuation in a thin boundary layer caused dissimilar turbulent transport because of the non-zero negative correlation of the streamwise velocity and dye concentration fluctuations for the wall-normal velocity fluctuation only on large scales. This explains the turbulent transport dissimilarity which leads to the zero averaged Reynolds shear stress and non-zero wall-normal turbulent mass flux.     

暖季强降雨对多年冻土南界斜坡路基稳定性影响分析

为阐明表面活性剂水溶液的减阻作用,使用LDV对零压梯度的二维湍流平板边界层中的CTAB 表面活性剂水溶液的湍流特性进行了实验研究. 结果表明：与牛顿流体相比,CTAB水溶液边 界层的粘性底层增厚;主流时均速度分布有被层流化的趋势,对数分布域上移;主流方向速 度湍动强度峰值减小,且远离壁面,在靠近边界层中部,出现第2峰值;垂直于主流方向的 速度湍动强度受到了大幅度抑制,雷诺应力沿着边界层厚度方向几乎为零. 结果说明CTAB 水溶液具有减弱湍流湍动各个成分相关度的作用,从而能够使雷诺应力降低、湍流能量生成 项减小最终降低流体的输送动力.     

Anisotropic Turbulence and Coherent Structures in Eccentric Annular Channels

Eccentric annular pipe flows represent an ideal model for investigating inhomogeneous turbulent shear flows, where conditions of turbulence production and transport vary significantly within the cross-section. Moreover recent works have proven that in geometries characterized by the presence of a narrow gap, large-scale coherent structures are present. The eccentric annular channel represents, in the opinion of the present authors, the prototype of these geometries. The aim of the present work is to verify the capability of a numerical methodology to fully reproduce the main features of the flow field in this geometry, to verify and characterize the presence of large-scale coherent structures, to examine their behavior at different Reynolds numbers and eccentricities and to analyze the anisotropy associated to these structures. The numerical approach is based upon LES, boundary fitted coordinates and a fractional step algorithm. A dynamic Sub Grid Scale (SGS) model suited for this numerical environment has been implemented and tested. An additional interest of this work is therefore in the approach employed itself, considering it as a step into the development of an effective LES methodology for flows in complex channel geometries. Agreement with previous experimental and DNS results has been found good overall for the streamwise velocity, shear stress and the rms of the velocity components. The instantaneous flow field presented large-scale coherent structures in the streamwise direction at low Reynolds numbers, while these are absent or less dominant at higher Reynolds and low eccentricity. After Reynolds averaging is performed over a long integration time the existence of secondary flows in the cross session is proven. Their shape is found to be constant over the Reynolds range surveyed, and dependent on the geometric parameters. The effect of secondary flows on anisotropy is studied over an extensive Reynolds range through invariant analysis. Additional insight on the mechanics of turbulence in this geometry is obtained.     

Constant Reynolds number turbulence downstream of an orificed perforated plate

Quasi-isotropic turbulence was experimentally produced in a wind tunnel via an orificed, perforated plate (OPP) at 10.5 m/s. The OPP consists of a lattice arrangement of 38.1 mm holes occupying 57% of the plate area. The OPP turbulence was found to be homogeneous over the cross section normal to the mean flow with Gaussian-like turbulence fluctuation. The isotropy of the turbulence field as portrayed by the streamwise/lateral turbulence intensity ratio was found to be approximately 1.1. The OPP turbulence is essentially self-preserving wherein the Taylor microscale Reynolds number remains nearly constant and the lateral velocity correlations collapse into a single curve.     

Measurements of turbulent flow in a channel at low Reynolds numbers

Normal and streamwise components of the velocity fields of turbulent flow in a channel at low Reynolds numbers have been measured with laser-Doppler techniques. The experiments duplicate the conditions used in current direct numerical simulations of channel flow, and good, but not exact, agreement is found for single-point moments through fourth order. In order to eliminate LDV velocity bias and to measure velocity spectra, the mean time interval between LDV signals was adjusted to be much smaller than the smallest turbulence time scale. Spectra of the streamwise and normal components of velocity at locations spanning the channel are presented.