Relationship between thermal degradation behavior and flame retardancy on polycarbonate–polydimethylsiloxane block copolymer

This article describes the thermal degradation behavior of polycarbonate–polydimethylsiloxane (PC–PDMS) block copolymer with dimethylsiloxane (DMS) block size 15 to 350 units, and the effects of the PDMS block size and the PDMS content on thermal degradation were studied. PC–PDMS block copolymer with DMS unit of 100 had the lowest value of maximum weight loss rate and the most residue containing silica in the other PC–PDMS block copolymers. The PDMS block size influenced PDMS dispersibility in PC and the moderate PDMS dispersion (? 50 nm) caused high flame retardancy for PC. The control of nanodispersion of PDMS caused the change of thermal degradation behavior and high flame retardancy in PC. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1697–1705, 2006     

Synthesis and characterization of gelatin‐polydimethylsiloxane graft copolymers

Gelatin‐polydimethylsiloxane (PDMS) graft copolymers were prepared through the reaction between gelatin and α‐[3‐(2,3‐epoxypropoxy)propyl]‐ω‐butyl‐PDMSs. The copolymers were characterized by FTIR and ¹H‐NMR spectra. As proved by wide angle X‐ray analysis, a new characteristic crystalline peak appeared after the bonding of PDMS to gelatin chains. The microstructure and the elemental identification of gelatin and copolymers were followed through scanning electron microscope with energy dispersive spectrometer. The glass transition temperature of gelatin and copolymers were obtained by differential scanning calorimetry analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface properties of block and graft polystyrene–polydimethylsiloxane copolymers

The surface compositions of a series of polystyrene‐b‐polydimethylsiloxane (PS‐b‐PDMS) and polystyrene‐g‐polydimethylsiloxane (PS‐g‐PDMS) copolymers were investigated using ATR‐FTIR and XPS technique. The results showed that enrichment of PDMS soft segments occurred on the surface of the block copolymers as well as on that of graft copolymers. And the magnitude order of the enrichment was as follows: PS‐b‐PDMS > PS‐g‐PDMS, which was attributed to the facilitating of the movement of the PDMS segments in PS‐b‐PDMS copolymer. Meanwhile, the solvent type and the contact medium had influence on the accumulation of PDMS on the surfaces. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of biodegradable and biocompatible amphiphilic block copolymers bearing pendant amino acid residues

Polylactide (PLA)-based biodegradable and biocompatible amphiphilic block copolymers bearing pendant amino acid residues were synthesized through a relatively easy and efficient way. The composition and structure of these copolymers were characterized by gel permeation chromatography (GPC) and ¹H nuclear magnetic resonance (¹H NMR) spectroscopy. The self-assembly behavior of the copolymers was investigated by fluorescence (FL), dynamic light scattering (DLS), and transmission electron microscope (TEM). It was shown that aggregates less than 100 nm in average size were formed by these copolymers, which changed from micelles to vesicles with the variation of the block length. In addition, the in vitro cytotoxicity of these copolymers was determined and compared with that of PEO-b-PLA in the presence of Bel-7402 cells. The result suggested that the block copolymers PAGE/cys-b-PLA exhibited better biocompatibility. Therefore, these PLA-based copolymers are expected to find promising applications in drug delivery or tissue engineering.     

Processability of polysulfone improved by adding polyamide 6 and polysulfone‐polyamide 6 block copolymer

Although polysulfone (PSU) is a potential thermoplastic engineering plastic with high heat resistance, good dimensional stability and excellent mechanical properties, its poor processability has greatly restricted its application in electrical, aerospace, and medical fields. In this work, polyamide 6 (PA6) and PSU‐PA6 block copolymer (PSU‐b‐PA6) were used to improve the processibility and formability of PSU depending on their excellent fluidity and good compatibility between two components. Furthermore, the fluidity, thermal and mechanical properties of the blends were carefully investigated. It was found that, melt flow index of PSU could be increased above 10 times, and strength and toughness could be enhanced by 4–10% with the introduction of 10 wt % PA6 and PSU‐b‐PA6 without compromising the heat resistance of PSU obviously. The processing conditions of PSU could be improved while maintaining a decent comprehensive performance. Thus, the method has great potential for extending the applications of PSU. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41139.     

Synthesis and characterization of hexafluoroisopropylidene bisphenol poly(arylene ether sulfone) and polydimethylsiloxane segmented block copolymers

A series of hexafluoroisopropylidene bisphenol poly(arylene ether sulfone) (BAF PAES) segmented block copolymers with varying fractions of polydimethylsiloxane (PDMS) were synthesized by a condensation reaction of hydroxyl-terminated BAF PAES and dimethylamino endcapped PDMS. The segmented block copolymers have high thermal stability. The BAF PAES homopolymer exhibits a tensile modulus of 1700 MPa and an elongation at break of 16%. Copolymerizing BAF PAES with increasing molecular weight amounts of PDMS results in tensile properties ranging from plastic to elastomeric where the elongation is 417% for a segmented block copolymer with 64 wt% PDMS incorporated. The morphological properties of these segmented block copolymers were characterized by atomic force microscopy (AFM), small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM). AFM and TEM images show the segmented block copolymers were microphase separated, and comparison with bisphenol A (BA) PAES-b-PDMS segmented block copolymers revealed complex differences between the morphological behavior of the two systems. SAXS data of the segmented block copolymers supports AFM and TEM images, indicating microphase separation but little long-range order.     

Alternating block copolymers based on polyamide‐12 and polycaprolactone

A series of alternating polyester/polyamide block copolymers were prepared by sequential conversion of hydroxy‐terminated polycaprolactone and amino‐terminated polyamide‐12 with a selectively reacting coupling agent. The thermal properties of the block copolymers were investigated using differential scanning calorimetry and dynamic mechanical analysis. Mechanical properties were determined using tensile and impact tests. All polymers were phase‐separated, where the polyamide phase was semicrystalline in all compositions. Distinct crystallization of the polycaprolactone phase was observed only when the block length was greater than 2000 g mol^?1. Mechanical testing showed that the polymers behave in a manner similar to that of thermoplastic elastomers. In particular, samples with a high content of polycaprolactone showed high strain and good impact behaviour. Copyright © 2011 Society of Chemical Industry     

Starch‐g‐polycaprolactone copolymerization using diisocyanate intermediates and thermal characteristics of the copolymers

Starch‐g‐polycaprolactone copolymers were prepared by two‐step reactions. The diisocyanate‐terminated polycaprolactone (NCO–PCL) was prepared by introducing NCO on both hydroxyl ends of PCL using diisocyanates (DI) at a molar ratio between PCL and DI of 2:3. Then, the NCO–PCL was grafted onto corn starch at a weight ratio between starch and NCO–PCL of 2:1. The chemical structure of NCO–PCL and the starch‐g‐PCL copolymers were confirmed by using FTIR and ¹³C‐NMR spectrometers, and then the thermal characteristics of the copolymers were investigated by DSC and TGA. By introducing NCO to PCL (M_n : 1250), the melting temperature (T_m ) was reduced from 58 to 45°C. In addition, by grafting the NCO–PCL (35–38%) prepared with 2,4‐tolylene diisocyanate (TDI) or 4,4‐diphenylmethane diisocyanate (MDI) onto starch, the glass transition temperatures (T_g 's) of the copolymers were both 238°C. With hexamethylene diisocyanate (HDI), however, T_g was found to be 195°C. The initial thermal degradation temperature of the starch‐g‐PCL copolymers were higher than that of unreacted starch (320 versus 290°C) when MDI was used, whereas the copolymers prepared with TDI or HDI underwent little change. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 986–993, 2000     

Synthesis and characterization of advance PA6‐b‐PDMS multiblock copolymers

Advance polyamide‐6‐b‐polydimethylsiloxane (PA6‐b‐PDMS) multiblock copolymers were first synthesized via the polymerization in bulk. Binary carboxyl terminated PA6 was served as the hard segment and PDMS modified with hexamethylene diisocyanate (PDMS‐NCO) was the soft segment. A series of PA6‐b‐PDMS copolymers based on different content and length of soft segments were obtained. Interestingly, Differential scanning calorimetry (DSC) studies revealed no obvious change in melting temperature after introducing PDMS segments to copolymers. The high melting temperatures indicated these copolymers possess potential applications in automotive industry that require high continuous use temperatures. DSC and transmission electron microscopy studies both demonstrated increasing the length and the content of the soft segment contributed to increasing of the degree of microphase separation. However, the improvement of thermal stability resulting from PDMS segments was also observed by thermo gravimetric analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41114.     

Optical properties of block copolymers containing pendant carbazole groups and in situ synthesized CdS nanoclusters

Ultraviolet–visible absorption spectra and photoluminescence spectra were used to demonstrate efficient charge‐carrier migration in a novel bulk heterogeneous block copolymer system. One moiety of the block copolymer was functionalized with charge‐transporting carbazole groups, whereas the other block formed domains suitable for the in situ synthesis of CdS nanoclusters. The excitation of the cluster‐free copolymers with 350‐nm‐wavelength radiation led to a strong emission peak at 450 nm that was associated with the carbazole groups. When CdS clusters were present in nearby but spatially distinct domains, the carbazole emission was completely quenched and replaced by a very broad emission in the visible range (near 560 nm). The implications of these observations are discussed in the context of the energy‐transfer mechanism and possible device applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 177–182, 2003     

Synthesis and surface characterization of poly(methyl methacrylate)‐block‐polydimethylsiloxane copolymers from macroazoinitiator

Poly(methyl methyacrylate)‐block‐polydimethylsiloxane (PMMA‐b‐PDMS) copolymers with various compositions were synthesized with PDMS‐containing macroazoinitiator (MAI), which was first prepared by a facile one‐step method in our lab. Results from the characterizations of X‐ray photoelectron spectroscopy (XPS), contact angle measurements, and atomic force microscopy (AFM) showed that the copolymer films took on a gradient of composition and more PDMS segments enriched at the film surfaces, which then resulted in the low surface free energy and little microphase separation at the film surfaces. By contrast, transmission electron microscopy (TEM) analysis demonstrated that distinct microphase separation occurred in bulk. Slight crosslinking of the block copolymers led to much steady morphology and more distinct microphase separation, in particularly for copolymers with low content of PDMS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Morphology and thermomechanical properties of epoxy thermosets modified with polysulfone‐block‐polydimethylsiloxane multiblock copolymer

Polysulfone‐block‐polydimethylsiloxane (PSF‐b‐PDMS) multiblock copolymer was synthesized via the Mannich polycondensation between phenolic hydroxyl‐terminated polysulfone and aminopropyl‐terminated polydimethylsiloxane in the presence of formaldehyde. The multiblock copolymer was characterized by means of nuclear magnetic resonance spectroscopy (NMR) and gel permeation chromatography (GPC) and used as a modifier to improve the thermomechanical properties of epoxy thermosets. Transmission electron microscopy (TEM) showed that the epoxy thermosets containing PSF‐b‐PDMS multiblock copolymer possesses the microphase‐separated morphological structures. Depending on the content of the PSF‐b‐PDMS multiblock copolymer, the spherical particles with the size of 50–200 nm in diameter were dispersed into the continuous epoxy matrices. The measurement of static contact angles showed that with the inclusion of PSF‐b‐PDMS multiblock copolymer, the epoxy thermosets displayed the improved surface hydrophobicity. It is noted that the epoxy resin was significantly toughened in terms of the measurement of critical stress field intensity factor (K_1C). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Structural effects of pendant groups on thermal and electrical properties of polyimides

Two series of aromatic polyimides containing various‐sized alkyl side groups were synthesized by thermal imidization of the poly(amic acid)s prepared from the polyaddition of benzophenonetetracarboxylic dianhydride and hexafluoro‐isopropylidene bis(phthalic anhydride) with 4,4′‐methylenedianiline, 4,4′‐methylene‐bis(2,6‐dimethylaniline), 4,4′‐methylene‐bis(2,6‐diethylaniline), and 4,4′‐methylene‐bis(2,6‐diisopropylaniline). The extent to which alkyl substitutes affect the thermal properties of polyimides was examined by differential scanning calorimetry, thermomechanical analyzer, and thermogravimetric analysis techniques. The analytical results demonstrated that the incorporation of alkyl moieties causes a moderate increase in the coefficient of thermal expansion and a slight decrease in thermal stability. Notably, all polymers had a decomposition temperature exceeding 500°C. The glass transition temperature increases markedly when hydrogen atoms at ortho positions on aniline rings are replaced with methyl groups, but decreases with growing alkyl side group size. The dielectric measurements show that the polymer possessing a large alkyl side group would have the lower dielectric value. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4672–4678, 2006     

Synthesis and characterization of diblock copolymers based on crystallizable poly(ε-caprolactone) and mesogen-jacketed liquid crystalline polymer block

Diblock copolymers comprising crystallizable poly(ε-caprolactone) and poly{2,5-bis[(4-methoxyphenyl)oxycarbonyl]styrene} (PMPCS) were synthesized by ring-opening polymerization of ε-caprolactone and subsequent atom transfer radical polymerization (ATRP) of MPCS. The molecular structure of the copolymers was confirmed by ¹H NMR spectroscopy and GPC. Kinetic study of ATRP showed that the polymerization proceeded in a controlled way up to high conversions. Three series of diblock copolymers were obtained with relatively narrow polydispersity indices (PDI≤1.11) and PCL blocks of 8000, 12,900, and 22,800 molecular weights, respectively. The existence of microphase separation was identified by differential scanning calorimetry (DSC) and directly observed through transmission electron microscopy (TEM). The melting behavior of PCL block was significantly affected by the length of PCL block and composition of PMPCS. The thermotropic liquid crystalline behavior was examined by polarized optical microscopy (POM) and DSC. The result showed that the diblock copolymer exhibited liquid crystalline behavior when the degree of polymerization (DP) of PMPCS block was not less than 44.     

Synthesis and characterization of block copolymers based on natural rubber and polypropylene oxide

Segmented block copolymers from different grades of hydroxyl terminated liquid natural rubber (HTNR) (M _n 3000, 8800, 10,000, and 17,000) and polypropylene oxide (PPO) (M _n 1000, 2000, 3000, and 4000) have been synthesized and characterized by spectral analysis, thermal analysis, scanning electron microscopy (SEM), and mechanical testing. The glass transition temperature of NR block was found to be at about ?64°C, which is independent of the PPO whose transition is around 15°C. The thermogravimetric analysis (TGA) shows that the thermal degradation of the samples proceeded in two steps characteristic of the immiscible components. The inability of PPO segments to provide physical crosslinking and the subsequent formation of hard domains is reflected in the low tensile properties and tear properties. The amorphous nature of the PPO phase and its immiscibility with NR phase are evidenced by the SEM studies. The effect of molecular weight of PPO as well as HTNR on the properties of the block copolymers has also been discussed. © 2006 Wiley Periodicals, Inc. JAppl Polym Sci 103: 909–916, 2007     

Synthesis, characterization and self-assembly behavior of six-armed star block copolymers with triphenylene core

Hexa-armed star block copolymers, s-[poly(l-lactide)-b-poly(styrene-co-N-acryloxysuccinimide)]₆ (s-[PLLA-b-poly(St-co-NAS)]₆) with triphenylene core have been successively prepared by the combination of ring-opening polymerization and atom transfer radical copolymerization, and they were used in the self-assembly in tetrahydrofuran, and the micelles with triphenylene core and PLLA as inner layer as well as poly(St-co-NAS) as shell were formed. After shell was cross-linked, PLLA was hydrolyzed in aqueous NaOH solution, the hollow spheres were formed. The structures, molecular weight and polydispersity index of the polymers were characterized by their ¹H NMR and FT-IR spectra, as well as GPC. Their morphologies were studied by TEM. The influence factors on the formation of various morphologies are under investigation.     

Synthesis and characterization of pH/temperature-sensitive block copolymers via atom transfer radical polymerization

In order to prepare well-defined pH-sensitive block copolymers with a narrow molecular weight distribution (MWD), we synthesized a pH-sensitive block copolymer via atom transfer radical polymerization (ATRP) of sulfamethazine methacrylate monomer (SM) and amphiphilic diblock copolymers by the ring-opening polymerization of d,l-lactide/?-caprolactone (LA/CL), and their sol-gel phase transition was investigated. SM, which is a derivative of sulfonamide, was used as a pH responsive moiety, while PCLA-PEG-PCLA was used as a biodegradable, as well as a temperature sensitive one, amphiphilic triblock copolymer. The pentablock copolymer, OSM-PCLA-PEG-PCLA-OSM, was synthesized using Br-PCLA-PEG-PCLA-Br as an ATRP macroinitiator. The number average molecular weights of SM were controlled by adjusting the monomer/initiator feed ratio. The macroinitiator was synthesized by the coupling of 2-bromoisobutyryl bromide with PCLA-PEG-PCLA in the presence of triethyl amine catalyst in dichloromethane. The resultant block copolymer shows a narrow polydispersity. The block copolymer solution shows a sol-gel transition in response to a slight pH change in the range of 7.2-8.0. Gel permeation chromatography (GPC) and NMR were used for the characterization of the polymers that were synthesized.     

Application of styrene‐acrylonitrile random copolymer–polyarylate block copolymer as reactive compatibilizer for polyamide and acrylonitrile‐butadiene‐styrene blends

Styrene‐acrylonitrile random copolymer (SAN) and polyarylate (PAr) block copolymer were applied as a reactive compatibilizer for polyamide‐6 (PA‐6)/acrylonitrile‐butadiene‐styrene (ABS) copolymer blends. The SAN–PAr block copolymer was found to be effective for compatibilization of PA‐6/ABS blends. With the addition of 3.0–5.0 wt % SAN–PAr block copolymer, the ABS‐rich phase could be reduced to a smaller size than 1.0 μm in the 70/30 and 50/50 PA‐6/ABS blends, although it was several microns in the uncompatibilized blends. As a result, for the blends compatibilized with 3–5 wt % block copolymer the impact energy absorption reached the super toughness region in the 70/30 and 50/50 PA‐6/ABS compositions. The compatibilization mechanism of PA‐6/ABS by the SAN–PAr block copolymer was investigated by tetrahydrofuran extraction of the SAN–PAr block copolymer/PA‐6 blends and the model reactions between the block copolymer and low molecular weight compounds. The results of these experiments indicated that the SAN–PAr block copolymer reacted with the PA‐6 during the melt mixing process via an in situ transreaction between the ester units in the PAr chain and the terminal amine in the PA‐6. As a result, SAN–PAr/PA‐6 block copolymers were generated during the melt mixing process. The SAN–PAr block copolymer was supposed to compatibilize the PA‐6 and ABS blend by anchoring the PAr/PA‐6 and SAN chains to the PA‐6 and ABS phases, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2300–2313, 2002     

Structural and magnetic characterization of norbornene-deuterated norbornene dicarboxylic acid diblock copolymers doped with iron oxide nanoparticles

A series of iron oxide doped norbornene (NOR)/deuterated norbornene dicarboxylic acid (NORCOOH) diblock copolymers were synthesized and characterized by X-ray photoelectron spectroscopy (XPS), small angle neutron scattering (SANS) and superconducting quantum interference device (SQUID) experiments. γ-Fe₂O₃ nanoparticles were synthesized within the microdomains of diblock copolymers with volume fractions of NOR/NORCOOH 0.64/0.36, 0.50/0.50 and 0.40/0.60. A spherical nanoparticle morphology was displayed in the polymer with 0.64/0.36 volume fraction. Polymers with 0.50/0.50 and 0.40/0.60 volume fractions exhibited interconnected metal oxide nanostructures. The observed changes in the shape and peak positions of the small-angle neutron scattering profiles of polymers after metal doping were related to the scattering from the metal oxide particles and to the possible deformed morphologies due to the strong interparticle interactions between metal particles, which may influence the polymer microphase separation. The combined scattering from both polymer domains and magnetic particles was depicted in SANS profiles of metal oxide doped polymers. γ-Fe₂O₃ containing block copolymers were superparamagnetic at room temperature. An increase in the blocking temperature (T_b) of interconnected nanoparticles was observed and was related to the interparticle interactions, which depends on the average distance (d) between particles and individual particle diameter (2R). The sample with volume fraction of 0.4/0.6 have the lowest d/(2R) ratio and exhibit the highest T_b at 115 K.     

Synthesis and characterization of styrene–N-butyl maleimide copolymers using iniferters containing thiyl end groups

The radical homopolymerization of styrene or copolymerization of styrene (S) with N-butyl maleimide (I) initiated by tetraethylthiuram disulfide was used to prepare macroinitiators having thiyl end groups. The S–I copolymers from the feeds containing 30–70 mol % I showed approximately alternating composition. The rate of copolymerization and molecular weights decreased with increasing maleimide derivative concentration in the feed; homopolymerization of I alone did not proceed. The macroinitiators served for synthesis of further S–I copolymers. Using polystyrene macroinitiator and the S–I copolymer with thiyl end groups in the polymerization of S–I mixture and styrene, respectively, the copolymers containing blocks of both polystyrene and alternating S–I copolymer were obtained. The copolymerization of S–I mixture initiated with the S–I copolymer bearing thiyl end groups led to the extension of macroinitiator chains by the blocks of alternating copolymer. The presence of the blocks in the polymer products was corroborated using elemental analysis, size exclusion chromatography, and differential scanning calorimetry. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 755–762, 1998