紫外光固化环氧豆油丙烯酸酯的制备与表征

将环氧大豆油与丙烯酸反应制备出环氧豆油丙烯酸酯预聚物,讨论了反应温度、反应时间、催化剂、阻聚剂的种类与用量对合成反应的影响,并用红外光谱对产物的结构进行了表征。研究结果表明其最佳反应条件是:催化剂三苯基膦,反应温度110℃,反应时间8h。该预聚树脂可用紫外光固化,其固化膜硬度达3H,且具有较好的柔韧性和附着力。     

Synthesis of bio‐based polyurethanes from epoxidized soybean oil and isopropanolamine

Epoxidized soybean oil (ESO) and isopropanolamine were used to synthesize a new polyol mixture for preparation of bio‐based polyurethanes. The chemical synthetic route for reaction of ESO with isopropanolamine was analyzed by ¹H‐NMR. The results suggested that both ester groups and epoxy groups in ESO had reacted with amino group of isopropanolamine through simultaneous ring‐opening and amidation reactions. Epoxy groups in various situations exhibited different reactivity, and the unreacted epoxy groups were further opened by hydrochloric acid. The synthesized polyol mixture had high hydroxyl number of 317.0 mg KOH/g. A series of polyurethanes were prepared by curing the synthesized polyol mixture with 1,6‐diisocyanatohexance along with different amount of 1,3‐propanediol (PDO) as chain extender. Tensile tests showed that yield strengths of the polyurethanes ranged from 2.74 to 27.76 MPa depending on the content of PDO. Differential scanning calorimetry analysis displayed one glass transition temperature in the range of 24.4–28.7°C for all of the polyurethane samples, and one melt peak at high content of PDO. Thermogravimetric analysis showed that thermal degradations of the polyurethanes started at 240–255°C. In consideration of simple preparation process and renewable property of ESO, the bio‐based polyurethane would have wide range of applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

羟乙基纤维素接枝环氧大豆油高分子表面活性剂的合成及性能

以羟乙基纤维素(HEC)与环氧大豆油(ESO)为原料,四氯化锡(Sn Cl4)为催化剂,二甲亚砜(DMSO)为溶剂,在室温下反应制备了羟乙基纤维素接枝环氧大豆油(ESO-HEC);ESO-HEC经碱性水解后,用酸处理得到羟乙基纤维素接枝环氧大豆油水解的酸性产物(H-ESO-HEC);再通过Na OH中和H-ESO-HEC结构中的羧酸基团,得到3种HESO-HEC-Na高分子表面活性剂。通过FT-IR表征了3种表面活性剂酸性产物H-ESO-HEC的结构;热重测试表明H-ESO-HEC比HEC具有更好的热稳定性;动态表面张力测试表明当H-ESO-HEC-Na的质量浓度升高,动态表面张力下降,且质量浓度达到临界胶束浓度时,最小表面张力值可达29 m N/m;泡沫性能测试表明随着ESO接枝量的增多,H-ESO-HEC-Na高分子表面活性剂的起泡和稳泡能力逐渐增强;通过对H-ESO-HEC-Na水溶液/庚烷的界面张力进行测试,发现不同条件制备得到的H-ESO-HEC-Na水溶液/庚烷的最低界面张力值接近,为9.8 m N/m左右。     

Thermosetting foam with a high bio‐based content from acrylated epoxidized soybean oil and carbon dioxide

A resilient, thermosetting foam system with a bio‐based content of 96 wt % (resulting in 81% of C₁₄) was successfully developed. We implemented a pressurized carbon dioxide foaming process that produces polymeric foams from acrylated epoxidized soybean oil (AESO). A study of the cell dynamics of uncured CO₂/ AESO foams proved useful to optimize cure conditions. During collapse, the foam's bulk density increased linearly with time, and the cell size and cell density exhibited power‐law degradation rates. Also, low temperature foaming and cure (i.e. high viscosity) are desirable to minimize foam cell degradation. The AESO was cured with a free‐radical initiator (tert‐butyl peroxy‐2‐ethyl hexanoate, T_i ～ 60°C). Cobalt naphtenate was used as an accelerator to promote quick foam cure at lower temperature (40–50°C). The foam's density was controlled by the carbon dioxide pressure inside the reactor and by the vacuum applied during cure. The viscosity increased linearly during polymerization. The viscosity was proportional to the extent of reaction before gelation, and the cured foam's structure showed a dependence on the time of vacuum application. The average cell size increased and the cell density decreased with foam expansion at a low extent of cure; however, the foam expansion became limited and unhomogeneous with advanced reaction. When vacuum was applied at an intermediate viscosity, samples with densities ～ 0.25 g/cm³ were obtained with small (<1 mm) homogeneous cells. The mechanical properties were promising, with a compressive strength of ～ 1 MPa and a compressive modulus of ～ 20 MPa. The new foams are biocompatible. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of ultrasonic extrusion on properties of colloids and bio-based nanocomposites containing epoxidized soybean oil and nanoclay

Colloid prepared with epoxidized soybean oil (ESO) and a nanoclay, organically modified montmorillonite (OMMT), has been processed using an ultrasonic twin-screw extruder under various ultrasonic amplitudes and screw rotation speeds. Ultrasonic treatment has significantly increased OMMT dispersion in ESO, according to wide angle X-ray diffraction and rheological data. Yield stress, storage and loss modulus, and complex viscosity and relaxation time of the colloid have been increased with increase of ultrasonic amplitude. Under certain high ultrasonic amplitudes, the increase of one to two orders of magnitude in the above-mentioned properties of colloids has been observed. Creep and recoverable compliance have been decreased with the increase of ultrasonic amplitude. The tremendous changes in rheological properties of the colloid are a result of significantly improved OMMT dispersion with the aid of ultrasonic treatment. With no or low ultrasonic treatment, a higher screw rotation speed has improved OMMT dispersion since it brings more mixing effect. However, at high ultrasonic amplitudes, a higher rotation disrupts jet flow and has led to less dispersion improvement compared with the same colloid extruded at a lower rotation speed. Colloids extruded at 400 rpm were cured using triethylenetetramine to prepare bio-based nanocomposites. The nanocomposite prepared using colloid treated at 13 μm shows improved tensile strength and modulus compared with the nanocomposite prepared using untreated colloid.     

Ion chromatographic determination of phosphorus and tungsten in epoxidized soybean oil

Soybean oil has been epoxidized with hydrogen peroxide in the presence of catalytic amounts of trioctylmethyl-ammonium tetra(diperoxotungsto)phosphate. A fast ion-exchange chromatographic method with suppressed conductivity detection has been developed for determining residual contents of tungsten and phosphorus in the oil. Tungsten and phosphorus could be determined at concentrations of 66 and 11 ppm, respectively. At tungsten and phosphorus concentrations of 1000 and 50 ppm, measured repeatabilities were 1.3 and 1.5%, respectively.     

Interpenetrating polymer network structured thermosets prepared from epoxidized soybean oil/diglycidyl ether of bisphenol A

Epoxidized soybean oil (ESO)/diglycidyl ether of bisphenol A (DGEBA) in various blend ratios (i.e. 100/0, 90/10, 80/20, 70/30, 60/40, 50/50) was thermally cured using methylhexahydrophthalic anhydride in the presence of 2‐ethyl‐4‐methylimidazole catalyst. The tensile properties and fracture toughness of the ESO/DGEBA thermoset blends were determined. Thermal properties of the blends were characterized using dynamic mechanical analysis, differential scanning calorimetry and thermogravimetric analysis. Blending of ESO and DGEBA gave synergistic effects on the modulus, strength, glass transition temperature and thermal stability. However, the fracture toughness and elongation at break of ESO/DGEBA blends are lower than those of ESO, as expected. The enhancement in certain mechanical and thermal properties of ESO/DGEBA can be associated with the crosslink density, gel content and possible interpenetrating network of the resulting thermoset blends. © 2013 Society of Chemical Industry     

Synthesis and characterization of cast resin based on different saturation epoxidized soybean oil

Acrylated epoxidized soybean oils (AESOs) with different level of saturation were obtained by the ring opening of different saturation epoxidized soybean oils using acrylic acid as the ring opener. AESO‐based thermosets have been synthesized by free radical polymerization of these AESOs and methyl methacrylate. The thermal properties of these resins were studied by differential scanning calorimetry and thermo‐gravimetric analysis. The results indicated that the thermal stability of these resins depends upon the epoxy value; the glass transition temperature increases with increasing of epoxy value. The tensile and impact strength of the resins were also studied, and indicated that tensile strength increases with increasing epoxy value, whereas impact strength decreases. The resulting thermosets ranged from elastomers to glassy polymers.     

Curing kinetics of bio‐based epoxy resin based on epoxidized soybean oil and green curing agent

New thermoset with a high bio‐based content was synthesized by curing epoxidized soybean oil (ESO) with a green curing agent maleopimaric acid catalyzed by 2‐ethly‐4‐methylimidazole. Non‐isothermal differential scanning calorimetry and a relatively new integral isoconversional method were used to analyze the curing kinetic behaviors and determine the activation energy (E_a). The two‐parameter ?esták–Berggren autocatalytic model was applied in the mathematical modeling to obtain the reaction orders and the pro‐exponential factor. For anhydride/epoxy group molar ratio equal to 0.7, E_a decreased from 82.70 to 80.17 kJ/mol when increasing the amount of catalyst from 0.5 to 1.5 phr toward ESO. The reaction orders m and n were 0.4148 and 1.109, respectively. The predicted non‐isothermal curing rates of ?esták–Berggren model matched perfectly with the experimental data. © 2016 American Institute of Chemical Engineers AIChE J, 63: 147–153, 2017     

Preparation, characterization and mechanical properties of epoxidized soybean oil/clay nanocomposites

New epoxidized soybean oil (ESO)/clay nanocomposites have been prepared with triethylenetetramine (TETA) as a curing agent. The dispersion of the clay layers is investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD and TEM data reveal the intercalated structure of ESO/clay nanocomposites has been developed. The thermogravimetric analysis exhibits that the ESO/clay nanocomposites are thermally stable at temperatures lower than 180 °C, with the maximum weight loss rate after 325 °C. The glass transition temperature, T_g, about 7.5 °C measured by differential scanning calorimetry (DSC) and T_g about 20 °C measured by dynamic mechanical study have been obtained. The difference in the T_g between DSC and dynamic measurements may be caused by different heating rate. The nanocomposites with 5-10 wt% clay content possess storage modulus ranging from 2.0×10⁶ to 2.70×10⁶ Pa at 30 °C. The Young's modulus (E) of these materials varies from 1.20 to 3.64 MPa with clay content ranging from 0 to 10 wt%. The ratio of epoxy (ESO) to hydrogen (amino group of TETA) greatly affects dynamic and tensile mechanical properties. At higher amount of TETA, the nanocomposites exhibit stronger tensile and dynamic properties.     

Physical properties of water‐blown rigid polyurethane foams containing epoxidized soybean oil in different isocyanate indices

To explore the potential of isocyanate usage reduction, water‐blown rigid polyurethane foams were made by replacing 0, 20, and 50% of Voranoll® 490 in the B‐side of the foam formulation by epoxidized soybean oil (ESBO) with an isocyanate index ranging from 50 to 110. The compressive strength, density, and thermal conductivity of foams were measured. The foam surface temperature was monitored before and throughout the foaming reaction as an indirect indication of the foaming temperature. Increasing ESBO replacement and/or decreasing isocyanate index decreased the foam's compressive strength. The density of the foam decreased while decreasing the isocyanate index to 60. Further decrease in isocyanate index resulted in foam shrinkage causing a sharp increase in the foam density. The thermal conductivity of foams increased while decreasing the isocyanate index and increasing the ESBO replacement. Mathematical models for predicting rigid polyurethane foam density, compressive strength, and thermal conductivity were established and validated. Similar to compressive strength, the foaming temperature decreased while decreasing the isocyanate index and increasing the ESBO replacement. Because of the lower reactivity of ESBO with isocyanate, the rate of foaming temperature decrease with decreasing isocyanate index was in the order of 0% > 20% > 50% ESBO replacement. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and interfacial properties of aminosilane derivative of acrylated epoxidized soybean oil

In this study silanized acrylated epoxidized soybean oil (silanized‐AESO), a multifunctional monomer, was synthesized by reacting acrylated epoxidized soybean oil with 3‐Aminopropyltriethoxysilane via a Michael addition reaction using less than equivalent amount of the silane. The characterization of silanized‐AESO was done by NMR and IR spectroscopy. Free radically initiated homopolymer of silanized‐AESO was synthesized by using the residual acrylate groups. The silanized‐AESO homopolymer was characterized by IR spectroscopy. The interfacial adhesion of the polymer on glass surface before and after moisture cure was measured according to ASTM D 4541 Pull‐Off Adhesion Test. After moisture curing process, an approximate of eightfold improvement was observed in the adhesion strength. Prolonged exposure to 92% humidity for 48 h caused to approximately 15% decrease in the adhesion strength. Silanized‐AESO was copolymerized with styrene in 1 : 1 weight ratio via radical polymerization. The effect of increased crosslink density upon moisture cure on the mechanical and physical properties of silanized‐AESO‐styrene copolymer was analyzed by DMA (Dynamic Mechanical Analysis), swelling, and surface hardness tests. Upon moisture cure 35% improvement was observed in the storage modulus because of the increase in the crosslink density. According to tan δ curves and surface hardness tests, silanized‐AESO‐styrene copolymer shows heterogeneous morphology in crosslinked areas. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2244–2253, 2007     

Polymerization reactions of epoxidized soybean oil and maleate esters of oil‐soluble resoles

In this study, the polymerization reactions of epoxidized soybean oil (ESO) with the maleate half‐esters of oil‐soluble resoles and the properties of the final products were demonstrated. The maleate half‐esters of the dimeric oil‐soluble resoles were obtained by the esterification reaction of maleic anhydride with a p‐tertiary butyl phenol (p‐TBP) resole and p‐nonyl phenol resole resins in the first step. The monomers were characterized by IR and ¹H‐NMR techniques. Then, the oil‐soluble resole maleates were polymerized with ESO to obtain tough and load‐bearing thermoset materials. The thermal and mechanical properties of the materials were determined by dynamic mechanical analysis, differential scanning calorimetry, thermogravimetric analysis, and tensile strength testing. The tensile strengths and storage moduli of the crosslinked polymers varied between 0.17 and 13 MPa and 10 and 1088 MPa, respectively. The elongation percentages of the materials were between 1 and 128%. The thermal resistance of the thermosets was measured as the 5% weight loss temperature. The reaction product of the ESO and maleate ester of p‐TBP showed the highest 5% weight loss at 247°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41457.     

Biobased nanocomposites from clay modified blend of epoxidized soybean oil and cyanate ester resin

Novel bio-based nanocomposites were prepared by blending surface modified natural clay with epoxidized soybean oil (ESO) and cyanate ester resin (CE). A convenient method was employed to modify the attapulgite (ATT) clay by adsorbing the poly(ethylene glycol) diglycidyl ether (PEGDE) onto the clay surface, which was confirmed by the appearance of a new peak of infrared spectroscopy due to hydrogen bonding and chelation. Thermogravimetic analysis (TGA) showed that the amount of PEGDE adsorbed on ATT was influenced by PEGDE concentration in acetone solution. Scanning electron microscope (SEM) and transmission electron microscope (TEM) results showed that nanoscaled ATT dispersed well in the blend of epoxidized soybean oil (ESO) before and after curing. The thermal-physical and mechanical properties were evaluated by dynamic mechanical analysis (DMA), TGA and tensile mechanical test. The nanocomposites showed higher glass transition temperature and modulus, and the tensile strength of the nanocomposites was reinforced as compared to that of ESO/CE blends.     

反应条件对环氧大豆油酯化反应的影响研究

通过调节温度、投料比、投料方式、催化剂、阻聚剂用量等条件,合成了一系列环氧大豆油丙烯酸酯低聚物。采用紫外光固化制备固化膜,并测定了固化膜的凝胶含量。实验结果表明,产物的酯化程度随着反应温度的升高而增大,但过高的温度增加了产物的黏度。适当提高体系中环氧大豆油含量,改变投料方式,合适的催化剂和阻聚剂用量,有利于提高合成产物的酯化程度。最终得出反应温度120℃、n(环氧大豆油)∶n(丙烯酸)=1.12∶1、将环氧大豆油与阻聚剂预先混合,再滴加丙烯酸与催化剂的混合物的投料方式、w(阻聚剂)=0.15%,为最佳反应条件。     

聚乳酸/环氧大豆油共混物的性能

聚乳酸（PLA）与环氧大豆油（ESO）经熔融共混制得具有高韧性的PLA/ESO共混物,并研究了ESO含量对PLA微观形态、力学和流变性能的影响规律。结果表明：ESO可显著降低PLA的熔体黏度,提高PLA的韧性;PLA/ESO共混物在低ESO含量（10%）时为部分相容,而在高ESO含量（20%和30%）时发生了相分离,从而使共混物的断裂伸长率和冲击强度随ESO含量增加先增大后减小,且分别在ESO含量为20%和15%时达到最大值,约为PLA的17倍和2.9倍,而拉伸强度则随之减小。     

Epoxy‐montmorillonite clay nanocomposites: Synthesis and characterization

Nanocomposites of epoxy resin with montmorillonite clay were synthesized by swelling of different proportions of the clay in a diglycidyl ether of bisphenol‐A followed by in situ polymerization with aromatic diamine as a curing agent. The montmorillonite was modified with octadecylamine and made organophilic. The organoclay was found to be intercalated easily by incorporation of the epoxy precursor and the clay galleries were simultaneously expanded. However, Na‐montmorillonite clay could not be intercalated during the mixing or through the curing process. Curing temperature was found to provide a balance between the reaction rate of the epoxy precursor and the diffusion rate of the curing agent into the clay galleries. The cure kinetics were studied by differential scanning calorimetry. The exfoliation behavior of the organoclay system was investigated by X‐ray diffraction. Thermogravimetric analysis was used to determine the thermal stability, which was correlated with the ionic exchange between the organic species and the silicate layers. The morphology of the nanocomposites was evaluated by scanning electron microscopy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2201–2210, 2004     

Thermal and mechanical behavior of flexible polyurethane‐molded plastic films and water‐blown foams with epoxidized soybean oil

Water‐blown flexible polyurethane foams and molded plastic films were made by replacing 0 to 50% of Voranol® 4701 in the B‐side of foam and plastic film formulation by epoxidized soybean oil (ESBO). Physical properties of foams including density, 50% compression force deflection (CFD), 50% constant deflection compression (CDC), and resilience were determined. A dynamic mechanical spectrometer (DMS) and a differential scanning calorimeter (DSC) were used to characterize the hard segment (HS) and soft segment (SS) ratio and thermal properties of plastic. Various functional groups in both flexible polyurethane foam and plastic film were characterized using Fourier transform‐infrared spectroscopy with attenuated total reflectance (FTIR‐ATR). When increasing the ESBO content, both density and 50% CFD of water‐blown polyurethane foams decreased first, then increased. On the other hand, the 50% CDC and resilience of foams showed a sharp increase and decrease, respectively. When increasing the ESBO content, the peak of tan δ in DMS analysis and Δc_p in DSC analysis of plastic films both decreased indicating the hard segment increased and the soft segment decreased in plastic film, respectively. The FTIR‐ATR results also show the hydrogen‐bonded urethane group increased in plastic films with increasing ESBO content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of epoxy based nanocomposites

Epoxy‐clay nanocomposites were synthesized to examine the effects of the content and type of different clays on the structure and mechanical properties of the nanocomposites. Diglycidyl ether of bisphenol‐A (epoxy) was reinforced by 0.5–11 wt % natural (Cloisite Na⁺) and organically modified (Cloisite 30B) types of montmorillonite. SEM results showed that as the clay content increased, larger agglomerates of clay were present. Nanocomposites with Cloisite 30B exhibited better dispersion and a lower degree of agglomeration than nanocomposites with Cloisite Na⁺. X‐ray results indicated that in nanocomposites with 3 wt % Cloisite 30B, d‐spacing expanded from 18.4 Å (the initial value of the pure clay) to 38.2 Å. The glass transition temperature increased from 73°C, in the unfilled epoxy resin, to 83.5°C in the nanocomposite with 9 wt % Cloisite 30B. The tensile strength exhibited a maximum at 1 wt % modified clay loading. Addition of 0.5 wt % organically modified clay improved the impact strength of the epoxy resin by 137%; in contrast, addition of 0.5 wt % unmodified clay improved the impact strength by 72%. Tensile modulus increased with increasing clay loading in both types of nanocomposites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1081–1086, 2005