三检测通道-气相色谱法快速分析天然气的组成

采用配有五阀(2个十通阀和3个六通阀)、七柱(2根毛细管柱和5根填充柱)和三检测器(氢火焰离子化检测器A、热导检测器B和C)的气相色谱法测定了天然气的组分。借助阀的切换系统及设置的分析程序,一次进样便可实现天然气常规组分的测定。检测器A用于烃类气体的检测,检测器B用于永久气体的检测,检测器C用于氢气检测。根据标准样品组分的保留时间对未知样品作定性检测,用外标法进行定量测定。方法的精密度符合国家标准GB/T 13610-2003中的规定,本方法所测得的由标准气体所混合组成的标准样品中,各组分的测定值与标准值之间的相对误差均小于5%。     

电感耦合等离子体质谱法同时测定地质样品中镉、锗、钴

建立电感耦合等离子体质谱法同时测定地质样品中镉、锗、钴含量的分析方法。样品用氢氟酸-硝酸混合溶液加热溶解,然后加热浓缩驱酸,再用硝酸溶液(1+1)复溶提取,在选定的仪器工作条件下进行测定。镉、锗、钴的含量分别在0.00~0.10,0.00~5.00,0.00~50.00 μg/g范围内与质谱峰强度呈良好的线性关系,相关系数均大于0.999,方法检出限分别为0.01,0.02,0.02 μg/g。用该方法对国家一级标准物质进行测定,测定值的相对误差均小于10%,测定结果的相对标准偏差为0.79%~8.45%(n=12)。该方法样品处理过程简便,检测效率高,适用于批量地质样品中镉、锗、钴的测定。     

气相色谱-脉冲放电氦离子化检测器法同时测定乙烯或丙烯中5种无机气体

用带脉冲放电氦离子化检测器的气相色谱法同时测定乙烯或丙烯中氢气、氧气、二氧化碳、一氧化碳和氮气等5种无机气体的含量。充分气化的样品注入色谱仪,借助仪器的高度集约化操作程序及阀系统切换功能,样品流经2根微填充色谱柱,先后使氢气、氧气、二氧化碳、一氧化碳和氮气等5种气体得到分离和测定。这5种气体的体积分数均在0.50～10.0mL·m~(-3)内与其对应的峰面积呈线性关系,上述5种气体的检出限(3S/N)依次为0.02,0.01,0.02,0.03,0.01mL·m~(-3)。对一组5种气体的混合标准气体进行8次重复测定,其保留时间的相对标准偏差在0.040%～0.15%之间,其峰面积的相对标准偏差在0.98%～2.3%之间,证明此方法同时测定5种气体的重复性良好。对另一组5种气体的混合标准气体进行6次平行测定,测定值与已知值相符,测定值的相对标准偏差(n=6)均小于1.0%。     

氧瓶燃烧-硫氰酸汞分光光度法测定无卤低烟阻燃电缆料中痕量氯

采用氧瓶燃烧法对无卤低烟阻燃电缆料样品进行燃烧,用去离子水作为吸收液吸收释出的氯化氢气体,并用硫氰酸汞分光光度法测定样品中氯含量。氯离子的质量浓度在0.20～5.00mg.L-1范围内与吸光度呈线性关系。该方法用于无卤低烟阻燃电缆料样品中微量氯的测定;用标准加入法测得回收率在96.0%～103%之间,测定值的相对标准偏差(n=5)均小于4.5%。     

气相色谱附双柱双氢火焰离子化检测器法同时测定环境空气中的总烃和非甲烷总烃

建立一种气相色谱法配双柱双氢火焰离子化检测器(FID)同时测定环境空气中的总烃和非甲烷总烃含量的方法。全玻璃注射器中的样品(保存时间尽可能少于4h)通过连接两个定量环的十通阀直接进入气相色谱,分离总烃和甲烷的柱子均采用填充柱,载气均为氮气,流量分别为25,20mL·min~(-1)。根据气体在总烃柱和甲烷柱保留时间对总烃和甲烷进行定性,保留时间分别为0.120,0.404min;分别以扣除氧峰面积的总烃面积和甲烷峰面积对总烃和甲烷定量,再通过2者差值计算非甲烷总烃含量。结果表明:总烃与氮气、甲烷与氮气的物质的量之比均在0.5～10.0μmol·mol~(-1)内与其对应的色谱峰面积呈线性关系,总烃、甲烷、非甲烷总烃的检出限(3.143s)分别为0.025,0.031,0.031mg·m~(-3)(以甲烷计)。在3个浓度水平下进行回收试验,总烃和甲烷的回收率分别为99.8%～104%,99.7%～103%;测定值的相对标准偏差(n=6)分别为1.3%～5.6%,1.0%～5.1%。采用本方法对2个采样点位采集的样品中的总烃、甲烷含量进行了测定,计算出的非甲烷总烃质量浓度都小于1.0mg·m~(-3),以这两个样品为基质进行加标回收试验,总烃和甲烷的回收率分别为102%～105%,107%～109%;测定值的相对标准偏差(n=5)分别为1.1%～1.7%,1.8%～1.9%。     

X射线荧光光谱法在电气石标准物质均匀性检验中的应用

采用粉末压片–X射线荧光光谱法对电气石标准物质候选物的均匀性进行检验。选择Si,Al,Mg,Fe,Ca,Na等6个元素作为检验元素,样品以随机方式进行测量,根据单因素方差分析的F值和测定值的相对标准偏差(RSD)判定样品的均匀性,并计算了检测方法的误差和样品不均匀误差。结果表明,方差检验的F计算值在0.80~1.93之间,小于F临界值1.96,测定结果的相对标准偏差小于0.9%;检测方法相对标准偏差和样品不均匀度(以RSD表示)均小于0.5%,说明制备的电气石标准物质候选物具有良好的均匀性。通过公式计算,确定最小取样量为200 mg。该方法无需湿法分解样品,绿色环保,简便快速,测定结果精密度高。     

高分辨电感耦合等离子体质谱法测定地质样品中的微量锗

应用高分辨电感耦合等离子体质谱法测定地质样品中的微量锗。研究了地质样品中不同酸消解方法、提取方法对测定锗的影响,以及在高分辨电感耦合等离子体质谱仪高、中、低分辨率模式下测定地质样品中锗的质谱行为。用氢氟酸-硝酸体系分解样品,硝酸提取,在中分辨率模式下进行测定。方法的检出限(3s)为10ng·g-1。方法用于10个国家标准物质中锗含量的测定,测定值与认定值相符,测定值的相对标准偏差(n=10)小于4.5%。     

辉光放电质谱法测定核级石墨粉中痕量杂质

建立了直流辉光放电质谱法(DC-GDMS)测定核级石墨粉中痕量杂质元素的方法。用一定的压力将石墨粉镶嵌在高纯铟片上,形成一个直径约为5 mm的圆形石墨薄层,用铟片辅助石墨粉放电,实现了粉状样品直接检测。优化的实验条件为放电电流0.8 mA,放电电压1.2 kV,放电气体流速0.437 mL/min。用石墨粉标准样品(19J T61029)单点校准了仪器相对灵敏度因子,消除基体效应,实现15个关键杂质元素定量分析。方法检出限为5.0 ng/g,在单侧0.05显著性水平下,利用Student's t检验,方法测定结果t值均小于临界值,与标准值无显著性差异。相对标准偏差(RSD)均小于10%。本方法与电感耦合等离子体光谱法测定结果比较,相对误差在2.4%~17.4%之间。     

石墨炉原子吸收测定土壤中的Cd Pb

摘要：为了提升石墨炉原子吸收测定土壤样品中Cd和Pb的准确度和测试效率,对样品前处理和仪器测试等条件进行优化选择,确定了低温电热板消解样品时,硝酸、氢氟酸、高氯酸的三酸比例和复溶方式以及采用海光GGX-920型石墨炉原子吸收测定Cd和Pb的升温程序、样品和基体改进剂加入量等条件。应用选定方法条件分别对土壤标准物质GBW07403、GBW07449水系沉积物 GBW07309进行6次测定,测定值Cd的相对标准偏差RSD：2.49%~4.67%,相对误差RE：-2.31% ~ 2.22%,测定值Pb的相对标准偏差RSD：1.98%~ 2.54%,相对误差RE：-1.88% ~ 2.11%。此方法精密度和准确度均达到标准要求,是一种准确而快速的检测方法,适合大批量的环境样品检测。     

催化分光光度法测定地质样品中微量镓

在25mL反应体系中加入3.0mL硫酸(1.0mol/L)-盐酸(5.0mol/L)混合酸,3.0mL碘酸钾溶液(0.05mol/L),1.5mL胭脂红溶液(0.50g/L),微量镓对碘酸钾氧化胭脂红的褪色反应有良好的催化作用,为此建立了测定地质样品中微量镓的催化分光光度法。方法的线性范围在0~100μg/L,工作曲线的线性方程ΔA=2.369CGa+0.223 6(相关系数r=0.999 6),检出限(3S/N)为1.0×10~(-3)μg/mL。方法应用于地质标准样品中微量镓的测定(分别是岩石标准样品GBW07120和水系沉积物标准样品GBW07301a),测定值与认定值相符,测定值相对标准偏差(n=6)均小于5%,结果满意。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.