结构稳定的CuO/TiO_2纳米管的功能化溶胶修饰法制备及其催化CO氧化性能研究

以水热处理方法得到的钛酸纳米管为载体,采用含有醋酸铜的功能化钛溶胶对其进行一步浸渍修饰,制备结构稳定的CuO修饰TiO2纳米管催化剂(CuO/TiO2NTs)。通过XRD(X-射线衍射)、TEM(透射电子显微镜)、HR-TEM(高倍透射电子显微镜)、XPS(X-射线光电子能谱)、BET(氮气吸附-脱附法)、TPD(程序升温脱附法)等表征材料的结构和性质,并研究其催化CO氧化的性能。研究表明:经过溶胶浸渍处理过程,不仅将功能化铜组分负载在纳米管上,而且纳米管载体的耐热性能明显提高;催化剂载体、铜钛原子比及焙烧温度对催化剂的活性有明显影响,且400℃焙烧的Cu/Ti原子比为1∶5的CuO/TiO2NTs的活性最高。     

一维CdS/TiO2纳米材料的制备及其光催化性能

采用含有氯化镉和硫脲的钛溶胶对钛酸纳米管载体进行修饰,再经焙烧制得不同CdS含量的一维CdS/TiO2纳米材料.运用X射线衍射、透射电子显微镜、N2吸附-脱附、紫外-可见光谱和X射线光电子能谱等手段表征了材料的结构和性质,并考察了CdS/TiO2样品在紫外光及模拟日光条件下光催化降解甲基橙溶液的活性.结果表明,经高温焙...     

Fe2O3/TiO2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO₂纳米管阵列,采用化学浴方法在TiO₂纳米管阵列上修饰了Fe₂O₃纳米颗粒.利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能.结果表明,Fe₂O₃纳米颗粒的修饰将TiO₂纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe₂O₃/TiO₂纳米管阵列的光电流是未修饰的TiO₂纳米管阵列的9倍.而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO₂纳米管阵列高出30%.     

CuO表面修饰锐钛矿TiO2纳米管阵列及其电化学嵌锂性能

以（CH₂OH）₂、NH₄F和HCl为电解液,纯Ti片、CuCl₂和NaNO₃为主要原料,联用阳极氧化和水热法制备CuO表面修饰锐钛矿TiO₂纳米管阵列锂离子电池负极材料（CuO/TiO₂）。使用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、能谱仪（EDS）、X射线光电子能谱仪（XPS）和X射线衍射（XRD）,研究样品的形貌特征、元素分布、价态和微观物相组成。利用电池充放电测试仪和电化学工作站,探讨材料的电化学嵌锂性能。结果表明,表面修饰后的锐钛矿TiO₂纳米管阵列外侧出现了大量绒毛状纳米CuO,单个绒毛结构的宽度约4 nm,长度约10 nm。在0.3C的电流密度下进行恒电流充放电测试,首次放电容量为550 mAh·g^-1,充电容量为490 mAh·g^-1。50次循环后,可逆电流容量仍保持在320 mAh·g^-1,具有良好的循环稳定性和电化学特性。     

不同pH值制备的TiO2和TiO2/SiO2催化剂结构、表面性质及光催化活性

以TiOSO₄和SiO₂溶胶为原料, 采用沉淀法用氨水调节pH值制备TiO₂和TiO₂/SiO₂催化剂. 制备的催化剂用X射线衍射(XRD), 扫描电镜(SEM), N₂吸附(BET), 紫外-可见(UV-Vis)漫反射光谱, 程序升温脱附(NH₃-TPD), 傅里叶变换红外(FT-IR)光谱技术分析. XRD谱图显示纯TiO₂中锐钛型和金红石相共存, 且金红石相含量随pH值升高而增加. 但是, TiO₂/SiO₂催化剂只有锐钛型. 扫描电镜发现制备的催化剂呈类球形, 颗粒间相互交叠, 粒径在10-25 nm之间. TiO₂和TiO₂/SiO₂光催化剂的比表面积随pH值升高略有增大. SiO₂的添加会增大催化剂的比表面积. 程序升温脱附实验结果说明催化剂的表面酸量随pH值升高而增加. TiO₂/SiO₂的表面酸量比相同pH值制备的TiO₂大. 红外光谱分析说明Si掺杂和高pH值有利于催化剂表面生成更多的羟基. TiO₂和TiO₂/SiO₂光催化剂的催化活性随pH值升高而明显增强. TiO₂/SiO₂的光催化活性优于TiO₂. TiO₂/SiO₂催化剂具有较好的耐久性.     

SBA-15固载硅钨酸催化合成柠檬酸三丁酯

以硅钨酸(H4SiW12O40)为催化剂、介孔分子筛SBA-15为载体,将浸渍法与焙烧法相结合制备了一系列介孔分子筛固载硅钨酸复合催化剂SiW12/SBA-15;并利用红外光谱(FTIR)、粉末X-射线衍射(XRD)、N2吸附-脱附、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等对其组成、结构及形貌进行表征.将此...     

低温下溶胶凝胶法制备TiO2纳米晶

从含过量水的溶胶出发,在室温下得到了TiO₂纳米晶。通过红外光谱,透射电子显微镜法和X射线粉末衍射法对含有过量水的溶胶体系中TiO₂纳米晶的室温形成机理进行了研究。与传统的溶胶凝胶法相比,在改良的溶胶凝胶体系中,在缩聚反应之前由于水过量使得钛的先驱体快速且充分的水解,从而生成[TiO₆]基团,随之形成TiO₂纳米晶。晶粒的尺寸为约3.5 nm,该法得到的TiO₂纳米晶比传统溶胶凝胶法得到的TiO₂纳米晶和商用光催化剂德固赛P25具有更好的光催化活性。     

TiO2晶相对MnOx/TiO2催化剂催化NO氧化性能的影响

以浸渍在不同晶相TiO₂ （金红石型（R）、锐钛矿型（A）和P25型（P））上的锰基催化剂为对象,研究了TiO₂晶相对MnO_x/TiO₂催化剂催化NO氧化活性的影响。 结果表明,MnO_x/TiO₂（P）催化剂活性最高,NO转化率在300℃及GHSV = 20000 h^-1条件下可达83%。 各催化剂活性顺序为MnO_x/TiO₂（P）>MnO_x/TiO₂（A）>MnO_x/TiO₂（R）。采用X射线粉末衍射、场发射扫描电子显微镜、X射线光电子能谱、H₂程序升温还原和O₂程序升温脱附等手段研究了TiO₂晶相影响MnO_x/TiO₂催化剂催化活性的作用机理。结果表明,相比于A和R型TiO₂,P型TiO₂能够增加MnO_x在其表面的分散度并抑制催化剂颗粒的团聚和粘连,且更有利于Mn₂O₃的生成,而后者催化NO氧化活性比其它MnO_x更高;此外,P型TiO₂可以增加MnO_x尤其是Mn₂O₃的还原性,并可促进O₂^-从M³⁺-O键的脱附。     

TiO2-Al2O3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H₂原位还原法制备. 通过N₂吸附（BET）、X射线衍射（XRD）、透射电镜（TEM）、程序升温还原（TPR）,X射线光电子能谱（XPS）和等离子体发射光谱（ICP-AES）表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能. 结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al₂O₃的孔特征,具有较大的比表面积和较宽的孔分布,TiO₂主要以表面富集的形式分散在管状的γ-Al₂O₃表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni₂P和Ni₁₂P₅;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO₂趋于在块状的Al₂O₃表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni₂P. 不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n（Ti）/n（Al）=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340 ℃,3 MPa,氢油体积比500,液时空速3 h^-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

溶剂热法制备Ag/TiO2纳米材料及其光催化性能

以乙醇为溶剂, 钛酸四丁酯为前驱体, 用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂. 利用X射线衍射(XRD)、N₂吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征, 以亚甲基蓝(MB)溶液的脱色降解为模型反应, 考察了不同Ag含量样品的光催化性能. 结果表明: 用溶剂热法制备的样品中TiO₂皆为锐钛矿相, 金属Ag颗粒沉积在TiO₂表面, 粒径为2 nm左右, 比表面积较溶胶凝胶法制备的样品大大增加, 最高可达151.44 m²·g^-1; UV-Vis光谱和光催化实验表明: Ag修饰使TiO₂对光的吸收能力大大增强, 吸收带边红移至可见光区, 亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型; 溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品, 在紫外光和可见光下, Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.