Heterojunctioned CuO/Cu2O catalyst for highly efficient ozone removal

In recent years, near surface ozone pollution, has attracted more and more attention, which necessitates the development of high efficient and low cost catalysts. In this work, CuO/Cu₂O heterojunctioned catalyst is fabricated by heating Cu₂O at high temperature, and is adopted as ozone decomposition catalyst. The results show that after Cu₂O is heated at 180°C conversion of ozone increases from 75.2% to 89.3% at mass space velocity 1,920,000 cm³/(g·hr) in dry air with 1000 ppmV ozone, which indicates that this heterojunction catalyst is one of the most efficient catalysts reported at present. Catalysts are characterized by electron paramagnetic resonance spectroscopy and ultraviolet photoelectron spectroscopy, which confirmed that the heterojunction promotes the electron transfer in the catalytic process and creates more defects and oxygen vacancies in the CuO/Cu₂O interfaces. This procedure of manufacturing heterostructures would also be applicable to other metal oxide catalysts, and it is expected to be more widely applied to the synthesis of high-efficiency heterostructured catalysts in the future.     

A comparative investigation of NdSrCu_(1-x)Co_xO_(4-δ) and Sm_(1.8)Ce_(0.2)CU_(1-x)Co_xO_(4-δ) (x: 0-0.4) for NO decomposition

A series of single-phase T-structured NdSrCu_(1-x)Co_xO_(4-δ) with oxygen vacancies and T'-structured Sm_(1.8)Ce_(0.2)Cu_(1-x)Co_xO_(4-δ) (x:0-0.4) with oxygen excess were prepared using ultrasound-assisted citric acid complexing method, and characterized by means of techniques such as thermogravimetric analysis and NO temperature-progranuned desorption (NO-TPD). The catalytic activities of these materials were evaluated for the decomposition of NO. It was found that the NdSrCut_xCoxO4_b catalysts were of oxygen vacancies whereas the Sm_(1.8)Ce_(0.2)CU_(1-x)Co_xO_(4-δ) ones possessed excessive oxygen (i.e., over-stoichiometric oxygen); with a rise in Co doping level,the oxygen vacancy density of NdSrCu_(1-x)Co_xO_(4-δ) decreased while the over-stoichiometric oxygen amount of Sm_(1.8)Ce_(0.2)CU_(1-x)Co_xO_(4-δ)increased. The NO-TPD results revealed that NO could be activated much easier over the oxygen-deficient perovskite-like oxides than over the oxygen-excessive perovskite-like oxides, with the NdSrCuO_(3.702) catalyst showing the best efficiency in activating NO molecules. Under the conditions of 1.0% NO/helium, 2800 hr~(-1), and 600-900℃, the catalytic activity of NO decomposition followed the order of NdSrCuO_(3.702)> NdSrCu_(0.8)Co_(0.2)O_(3.736) > NdSrCu_(0.6)Co_(0.4)O_(3.789) > Sm_(1.8)Ce_(0.2)Cu_(0.6)Co_(0.4)O_(4.187)> Sm_(1.8)Ce_(0.2)Cu_(0.8)Co_(0.2)O_(4.104)> Sm_(1.8)Ce_(0.2)CuO_(4.045), in concord with the sequence of decreasing oxygen vacancy or oxygen excess density. Based on the results, we concluded that the higher oxygen vacancy density and the stronger Cu~(3+)/Cu~(2+) redox ability of NdSrCu_(1-x)Co_xO_(4-δ) account for the easier activation of NO and consequently improve the catalytic activity of NO decomposition over the catalysts.     

O3/H2O2法灭活水中剑水蚤类浮游动物

为解决水源水中孳生的水蚤类浮游动物难以被常规的水处理工艺有效地去除,困扰水厂正常生产运行的问题,进行了O2氧化、H2O2氧化和O3／H2O2高级氧化对水体中剑水蚤类浮游动物灭活效果的试验研究．发现3种方法中,O3／H2O2联合时除蚤效果最佳,在蒸馏水中投量为031．0mg／L、H2O24mg／L时,接触30min达到100％的灭蚤率;单独O3氧化效果也较好,投加1．0mg／L的灭蚤率为80％;H2O2氧化效果不理想,投加4mg／L几乎无灭蚤效果。进而考察确定了03／H2O2灭活剑水蚤的最佳工艺条件为：先加O3后加H2O2,投加间隔时间30～60s为宜;并探讨了H2O2投量、水体pH值以及有机物含量对O3／H2O2系统灭活剑水蚤效果的影响。试验中发现H2O2投量在4～10mg／L之间效果无较大变化,有机物含量对灭蚤影响较大,pH值的影响则较小。最后对O3／H2O2预氧化与水处理混凝沉淀工艺的协同除蚤效能进行了考察。结果表明,O3／H2O2预氧化与水处理混凝沉淀工艺的协同作用将会进一步提高除蚤的效果。     

锰离子催化臭氧液相烟气脱硫实验研究

对Mn2+催化臭氧(O3)液相氧化脱除二氧化硫(SO2)进行了实验研究,以揭示Mn2+对臭氧液相氧化SO2的影响.采用标准碘量法测定了O3浓度曲线.实验比较了添加Mn2+前后吸收液对SO2的脱除效率,并研究了O3与SO2摩尔比([O3]/[SO2])、Mn2+浓度对SO2脱除效率的影响.在[O3]/[SO2]=0.5、未添加Mn2+时O3对SO2的氧化效率为35%,而添加Mn2+后的氧化效率达到70%.随着[O3]/[SO2]的增大,SO2脱除效率逐渐增加,而且脱除效率也随Mn2+浓度的增加而增加,合适的Mn2+浓度范围为1.2×10-2~1.2×10-1mol/L.     

高湿度条件下分解臭氧的锰催化剂

分别以硝酸锰和乙酸锰为前体 ,用浸渍法制备了MnOx γ Al2 O3催化剂 ,考察了它们对高湿度高浓度臭氧的催化分解性能。分析了在不同的温度煅烧和用不同的前体制备的催化剂上的氧化锰的形态。实验表明 ,以乙酸锰为前体 ,在 4 0 0℃煅烧得到的催化剂的臭氧催化分解活性最高 ,保持 95 %的臭氧分解率 ,其使用寿命在 10 0h以上 ,该催化剂上锰的主要形态为Mn2 O3,在载体上分散性最好     

催化臭氧化法处理汽车厂综合废水的实验研究

根据臭氧化反应基本原理 ,选用Fe2 + 、Cu2 + 、H2 O2 、Fe2 + +H2 O2 等作催化剂 ,对臭氧在不同催化剂催化作用下降解汽车厂综合废水中有机物和氰化物的速率、最终去除率和臭氧利用效率进行了实验研究。实验结果表明 ,O3+H2 O2 +Fe2 + 工艺可高效去除废水中的有机物和氰化物 ,最终出水水质满足排放标准     

Catalysts for decomposing ozone tail gas

The preparation of immobilizing-catalysts for decomposing ozone by using dipping method was studied. XRD, XPS and TEM were used to characterize the catalysts. The three kinds of catalysts were selected preferentially, and their catalytic activities were investigated. The results showed that the catalyst with activated carbon dipping acetate( active components are Mn:Cu = 3:2, active component proportion in catalyst is 15%, calcination temperature is 200℃ ) has the best catalytic activity for ozone decomposing. One gram of catalyst can decompose 17.6g ozone at initial ozone concentration of 2.5g/m^3 and the residence time in reactor of 0.1s. The experimental results also indicated that humidity of reaction system had negative effect on catalytic activity.     

过渡金属催化剂对邻二氯苯的催化氧化研究

以过渡金属的氧化物制得催化剂系列 ,研究其对邻二氯苯的氧化活性 ,考察反应温度、催化剂负载量、空间速度对氧化过程的影响 ,过渡金属氧化物对邻二氯苯的氧化活性顺序为 :CrOx>CuOx >VOx >MnOx >MoOx。 5wt.%V 1 0wt.%Mo3wt.%Mn/Al2 O3催化剂在 350℃时对邻二氯苯转换率达到了 90 %以上。     

紫外光在臭氧降解不同有机物过程中的协同作用

利用O3／UV分别对与臭氧有不同反应活性的对氯苯酚、硝基苯、乙酸和草酸进行了降解试验,结果表明,UV与臭氧化降解的协同作用与目标有机物本身的性质有很大关系,在本实验条件下,UV与臭氧的联用反而降低了对氯苯酚的臭氧化降解效率,30min后体系的TOC去除率仅有59％,而单独臭氧化TOC的去除率达到了66％;对硝基苯和草酸而言,UV均明显地提高了臭氧的降解效率,40min时两者TOC的去除率分别为44％和90％,比单独臭氧化处理分别高出了6％和33％;但是,O3／UV对乙酸几乎无降解活性．在这4种有机物的单独臭氧化降解过程中,除对氯苯酚外,水中均可检测到溶解臭氧．以上的实验结果表明,目标有机物对紫外光的吸收及单独臭氧化过程水中溶解臭氧的存在是O3／UV降解效率提高的必要条件．除UV对目标有机物的活化作用外,降解过程的中间产物H2O2也是O3／UV降解效率提高的一个重要因素,UV分解溶解臭氧在此过程可能仅起了辅助作用。     

酸热氧化修饰合成MnOx/GAC催化臭氧氧化降解邻氯酚

通过酸热氧化修饰法在活性炭上负载锰氧化物,制得MnO_x/GAC催化剂,并研究其催化臭氧氧化降解邻氯酚的性能。结果表明:在催化剂投加量为0.1 g/L,臭氧浓度为20 mg/L,气体流量为0.5 L/min,初始pH为6的条件下,反应120 min时,邻氯酚的TOC去除率可达到95%,比单纯臭氧氧化提高了55百分点。在一定范围内,增加臭氧浓度和气体流量可以加快反应速率,提高TOC去除率,但通入过量的臭氧反而会降低TOC去除率。探究了无机阴离子对于体系TOC去除率的影响,研究发现:1 mmol/L的NO₃-、SO₄2-、Cl-对TOC去除率无明显影响,1 mmol/L Br-使体系TOC去除率降低了10%左右。pH是影响体系氧化能力的重要因素,在酸性条件下的TOC去除率远高于碱性条件下,这可能与催化剂表面官能团的作用和反应体系中无机碳的积累有关。此外,提出了催化剂表面羟基存在形式与pH之间的关系,以及不同羟基存在形式下催化臭氧分解产生的活性物种。     

氮掺杂生物炭催化臭氧对于布洛芬的降解特性与机制

系统研究了新型氮掺杂生物炭材料(N-C)催化臭氧对于水中布洛芬(IBP)的氧化降解效能及机制,并深入探究了初始pH、臭氧投加量、催化剂投加量、不同阴离子和背景水质条件对IBP降解效率的影响.结果 表明,相较于一些常见的碳基催化剂(g-C3N4、生物炭、颗粒活性炭)及金属催化剂(MnO2、Fe3O4),N-C催化臭氧体系...     

N-doped CoAl oxides from hydrotalcites with enhanced oxygen vacancies for excellent low-temperature propane oxidation

A series of nitrogen-doped CoAlO (N-CoAlO) were constructed by a hydrothermal route combined with a controllable NH₃ treatment strategy. The effects of NH₃ treatment on the physico-chemical properties and oxidation activities of N-CoAlO catalysts were investigated. In comparison to CoAlO, a smallest content decrease in surface Co³⁺ (serving as active sites) while a largest increased amount of surface Co²⁺ (contributing to oxygen species) are obtained over N-CoAlO/4h among the N-CoAlO catalysts. Meanwhile, a maximum N doping is found over N-CoAlO/4h. As a result, N-CoAlO/4h (under NH₃ treatment at 400°C for 4 hr) with rich oxygen vacancies shows optimal catalytic activity, with a T₉₀ (the temperature required to reach a 90% conversion of propane) at 266°C. The more oxygen vacancies are caused by the co-operative effects of N doping and suitable reduction of Co³⁺ for N-CoAlO/4h, leading to an enhanced oxygen mobility, which in turn promotes C₃H₈ total oxidation activity dominated by Langmuir-Hinshelwood mechanism. Moreover, in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTs) analysis shows that N doping facilities the decomposition of intermediate species (propylene and formate) into CO₂ over the catalyst surface of N-CoAlO/4h more easily. Our reported design in this work will provide a promising way to develop abundant oxygen vacancies of Co-based catalysts derived from hydrotalcites by a simple NH₃ treatment.     

铁锰双金属氧化物对过硫酸氢钾降解酸性橙7的催化效果

为了发挥均相体系中过渡金属元素对PMS(过硫酸氢钾)的催化效果,同时解决存在的金属离子污染的问题,以AO7(酸性橙7)为目标污染物,研究了采用溶胶-凝胶法(sol-gel method)制备Fe-MnO_x(铁锰双金属氧化物)催化剂催化PMS的效果及降解机理. 结果表明:ρ(Fe-MnO_x)由50 mg/L升至200 mg/L后,35 min时AO7降解率由53.74%升至96.65%;继续升高ρ(Fe-MnO_x),AO7降解率提升效果不明显. 随着ρ(PMS)₀(PMS初始质量浓度)的升高,AO7的降解率变化趋势与之相同;而随着ρ(AO7)₀(AO7初始质量浓度)的升高,AO7降解率有所下降. 分别投加EA(乙醇)、TBA(叔丁醇)这2种捕获剂来验证体系氧化物种时发现,55 min时AO7降解率分别为79.40%和91.33%,氧化体系的主要氧化物种为·SO₄-(硫酸根自由基)和少量·OH(羟基自由基). XRD(X射线衍射)和XPS(X射线光电子能谱)结果显示,Fe-MnO_x催化剂中的Fe、Mn主要以Fe3+、Mn2+、Mn4+ 3种形式存在,Fe、Mn、O 3种元素中,Fe3+、Mn2+、Mn4+、O2-和表面羟基氧的摩尔比分别为20.49%、26.46%、5.60%、32.51%和14.91%. 研究显示,Fe-MnO_x催化剂具有金属离子溶出量低、催化性能良好等优良性能,能够有效催化PMS生成自由基,对水中的污染物具有良好的降解效果.      

V2O5/AC在含SO2气氛中对气态Hg0的吸附脱除研究

利用固定床反应器研究了模拟烟气(N_2、SO_2、O_2)气氛下,气态Hg~0在V_2O_5/AC催化剂上的吸附脱除行为.考察了V_2O_5担载量、SO_2浓度和吸附温度等对V_2O_5/AC吸附脱除Hg~0的影响,并对V_2O_5/AC上吸附汞的形态进行了XPS分析表征.研究发现,V_2O_5/AC对Hg~0的吸附能力远大于载体AC.汞的吸附量与V_2O_5/AC中V_2O_5的质量分数有关,随着V_2O_5质量分数从0.5%增加到1.0%,汞的吸附量从75.9 μg·g~(-1)增加到89.6 μg·g~(-1) (无氧) 和115.9 μg·g~(-1)增加到185.5 μg·g~(-1) (有氧),远高于相同吸附条件下的AC上的汞吸附量 (9.6 μg·g~(-1)和23.3 μg·g~(-1)).SO_2对Hg~0的吸附有促进作用,主要是由于SO_2和Hg~0在V_2O_5/AC上发生了化学反应.但是当SO_2体积分数从500×10~(-6)增加到2 000×10~(-6)时,V_2O_5/AC对汞的吸附量只增加了5%.不同温度下的实验结果表明,V_2O_5/AC催化剂在150℃左右的吸附脱除Hg~0的能力最高,汞的吸附量达到98.5 μg·g~(-1) (无氧) 和187.7 μg·g~(-1) (有氧).XPS 分析结果表明,在V_2O_5/AC催化剂表面有HgO和HgSO_4生成,证实了V_2O_5和SO_2的作用.     

Ag-Al2O3催化剂选择性催化还原稀薄燃烧NOx的研究

本研究主要考察了丙烯为还原剂 ,溶胶 凝胶和共沉淀两种方法制备的Ag Al2 O3催化剂的活性 ,实验结果表明Ag(5 ) Al2 O3(SG)催化剂具有最高的活性。同时详细考察了C3H6 浓度、NO浓度和空速等因素对Ag(5 ) Al2 O3(SG)催化剂活性的影响 ,实验结果表明该催化剂在高空速条件下仍然具有良好的性能。此外 ,还考察了乙烯、丙烷和辛烷为还原剂 ,Ag(5 ) Al2 O3(SG)催化剂的活性 ,实验结果表明以辛烷为还原剂 ,该催化剂还原NOx 的活性 ,特别是低温活性明显提高     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide(NOx) by-products were investigated in a dielectric barrier discharge(DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide(Mn Ox), iron oxide(Fe Ox), cobalt oxide(Co Ox) and copper oxide(Cu O), supported on Al2O3/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO2 selectivity. In addition, NOx was suppressed with the decrease of specific energy density(SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the Cu O catalyst showed the best performance in NOx suppression. The Mn Ox catalyst exhibited the lowest concentration of O3 and highest CO2 selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

同一实验环境下炭黑燃烧催化剂活性测试及制备方法优选

催化燃烧是最有效的炭黑消除手段之一,催化剂是其中的核心,其活性的提高对催化效果优化及成本控制有重要影响.然而目前报道的大量炭黑燃烧催化剂活性测试是基于不同实验环境进行的,其结果之间缺乏比较意义.为了筛选活性优异的催化剂,并总结出催化剂活性与物理化学性质之间的关系,同时为催化过程中氧物种原位定量观测建立基础,根据易得、环...     

Toluene removal characteristics by a superimposed wire-plate dielectric barrier discharge plasma reactor

A superimposed wire-plate dielectric barrier discharge reactor was used to remove toluene in this study. The effects of oxygen content, gas flow rate, gas initial concentration and with/without catalyst on toluene decomposition were investigated. It was found that an optimal toluene removal was achieved when the oxygen content was about 5%. Under this condition, the highest toluene removal efficiency of 80.8% was achieved when the gas concentration was 80 mg/m^3. The toluene removal efficiency decreased with the increase of the gas flow rate and the initial concentration of toluene. In addition, the ozone concentration decreased with the increase of the initial concentration of toluene. It suggested that combining DBD （dielectric barrier discharge） with Co3O4/Al2O3/foam nickel catalyst in-situ could improve the toluene removal efficiency and suppress ozone formation. Products analysis showed that the main products were CO and CO2 when oxygen was more than 5%.     

ZnFe_2O_4/TiO_2光催化剂制备及乙酰甲胺磷降解性能研究

分别采用共沉淀法和溶胶-凝胶法制备了ZnFe2O4和掺杂ZnFe2O4的纳米级TiO2光催化剂,进行了XRD、TEM和UV visDRS表征,以卤素灯为光源对纳米TiO2降解水溶液中乙酰甲胺磷农药进行了研究。考察了反应液初始pH值、催化剂用量、H2O2用量对降解率的影响。实验结果表明,焙烧温度为400℃、掺杂量为0.5%的ZnFe2O4/TiO2纳米粉体降解效果最佳,在相同条件下,反应2h后农药降解率可比纯TiO2提高20%左右。正交实验优化了降解反应条件,在常温常压下,起始pH值为12、H2O2浓度为12mmol/L、催化剂浓度为0.5g/L、反应3h后,初始浓度为1.0×10-4mol/L的乙酰甲胺磷农药降解率可达61.2%。     

褐煤脱水及水质净化研究

为实现褐煤提质并缓解褐煤产区缺水现状,采用微波及水热脱水方法对褐煤进行脱水改性并回收褐煤所脱水分.通过检测水分化学需氧量、氨氮、总磷、硬度、离子、有机化合物等各项指标,对褐煤中水分进行深入分析,并比较两种脱水方法的脱水、净化效果.结果表明微波方式脱水率可达70%~80%,除化学需氧量外,其它水质指标均符合工业用水标准,且杂质含量随微波功率增加而降低,利于净化回收.水热方式可有效改善褐煤煤质,脱水率最高可达87.44%,但各项水质指标均大大超出标准范围,且杂质含量在250℃工况下达到最大.两种冷凝水均检测到微量有毒金属元素、有毒致癌的多环芳烃及酚类化合物,将成为后续净化的主要脱除对象.