共查询到20条相似文献,搜索用时 140 毫秒
1.
介绍了P370L汽车大梁用钢板板卷长度方向上抗拉强度,屈服强度,延伸率和断面收缩率在板卷头部,中部和尾部的波动状况,分析了产生波动的原因。 相似文献
2.
3.
4.
5.
6.
7.
8.
9.
10.
低合金高强钢因其应用环境以及使用条件的特殊性,常常需要具有良好的力学性能。微合金化结合一定的热处理工艺,可以有效提高低合金高强钢的性能。研究钛微合金化及热处理工艺对低合金高强钢组织和性能的影响规律及作用机理,对提高材料的性能、扩大材料的应用具有重要的意义。以C-Mn-Ti系Q355B板坯的试制过程为例,研究了钛微合金化冶金成分及轧制工艺控制对材料显微组织和力学性能的影响规律;对比了4种不同轧制工艺条件下所生产钢板的力学性能和金相微观组织;并分析了材料的强化机制。0℃和20℃时Q355B板的低温冲击性能、屈服强度和冷弯性能分析结果表明,冶炼过程中形成的较大尺寸的TiN和链状的Ti4C2S2对钢板的塑性和韧性均有负面影响;Ti微合金化后的钢板晶粒度均在9级以上;精开轧温度低于890℃,终冷温度在660±20℃波动时,钢板的综合力学性能最好。 相似文献
11.
12.
汽车用含铜高强度薄钢板 总被引:4,自引:1,他引:3
介绍了最新开发的汽车用含铜高强度热轧薄板和冷轧薄板。在超低碳钢中添加1%以上的铜,利用含铜相的沉淀硬化,获得了高强度和优良成形性兼备的冷轧和热轧薄板。含铜热轧薄板是一种热处理强化类型钢,经时效热处理使铜析出,产生强烈沉淀硬化,钢的抗拉强度在原基础上提高200MPa以上。 相似文献
13.
The microstructural evolution in a 700 MPa hot rolled high strength steel was analyzed in terms of strengthening mechanisms.The results show that the hot rolled sheet steel has yield strength of 710 MPa with good elongation and toughness.The strength of the developed 700 MPa hot rolled high strength steel is derived from the cumulative contribution of fine grain size,dislocation hardening and precipitation hardening.The fine grain strengthening and precipitation hardening are the dominant factors responsible for such high strength,and the amount of precipitation hardening is two or four times higher than that of conventional microalloyed hot rolled sheet steels reported in the past.Good toughness is due to refinement of ferrite grain size. 相似文献
14.
汽车用高强度IF薄钢板 总被引:10,自引:0,他引:10
高强度IF薄钢板是近年来开发的一种兼有高强度和良好深冲性能的汽车用钢板,它是在IF钢基础上通过添加适量的固溶强化元素来达到高强度的,总结了这种钢中的合金元素对基板性能及热镀锌镀层的影响,另外还介绍了两种新型的高强度IF钢,结合宝钢设备的情况,分析了高强度IF薄钢板开发的可行性。 相似文献
15.
《钢铁研究学报(英文版)》2011,(Z1):557-562
In order to reduce the transverse corner cracks of high strength weathering steel Q450NQR1,the factors influencing transverse corner cracks on continuously cast slab,such as level fluctuation of molten steel in mold,mold taper,primary cooling,mold powder,secondary cooling,nitrogen content in steel,spray nozzle structure,processing parameters and equipment of CC,etc.,were analyzed.Based on this,a series of comprehensive countermeasures have been proposed.The operation shows by the use of key technologies,including stabilizing steel level,optimizing the mold taper,weakening the primary cooling and the secondary cooling,reforming the mold powder,and adjusting spray nozzle structure,the transverse corner cracks on continuously cast slab have been significantly reduced,and the edge cracks on hot rolled sheet have been eliminated due to the transverse corner cracks.The qualified slabs are delivered to produce weathering cold forming sectional steel,whose yield strength is greater than 450MPa. 相似文献
16.
17.
18.
微合金化高强度钢轧制采用的工艺技术 总被引:1,自引:0,他引:1
本文综述微合金化高强度钢轧制采用的工艺技术,其中包括热装热送、板坯加热、控轧控冷、快速冷却、采用的新设备等工艺技术。重点是生产低碳、高韧性、高强度、易焊接的造船用钢采用形变热处理技术,以提高产量和质量,节省昂贵的Ni、Cr、Mo等合金,降低生产成本。 相似文献
19.
20.
简述了工业生产高强度热轧薄钢板的成分和生产工艺,其室温组织由极细的铁素体晶粒和极少量的珠光体组成。模拟高温搪烧时,随着温度的提高和保温时间的延长,屈服强度和抗拉强度下降,伸长率提高。经857 ℃保温10 min后,钢板的屈服强度满足了不小于310 MPa的要求。预变形时的变形量对模拟高温搪烧后钢板的力学性能也会产生影响。所研究的钢板在制作热水器内胆时能满足耐压不小于12 MPa和2万次的压力循环试验要求。 相似文献