The microstructures and property analysis of aliovalent cations (Sm,Mg, Ca,Sr, Ba) co-doped ceria-base electrolytes after an aging treatment

Ce_0.8Sm_0.15R_0.05O_2−δ (R = Sm, Mg, Ca, Sr, and Ba) specimens were successfully prepared using a solid-state reaction, and they were used in an intermediate temperate solid oxide fuel cell (IT-SOFC) electrolyte. This study focused on the effects of co-doping and an aging treatment for the conductivities and microstructures of CeO₂-based ceramics and also analyzed the variation of the conductivity in the reducing atmosphere. The study showed that the conductivities of the CeO₂-based materials have a higher conductivity at 500–800 °C by the co-doping aliovalent cations Sm and R. The conductivity increased with the increasing oxygen vacancies that were induced from charge compensation. The XRD and EDS analyses showed that the MgO and BaCeO₃ phases appeared in the Ce_0.8Sm_0.15Mg_0.05O_2−δ and Ce_0.8Sm_0.15Ba_0.05O_2−δ specimens, respectively. The conductivity of the Ce_0.8Sm_0.15Ca_0.05O_2−δ specimens was higher, approximately 0.0837 S/cm at 800 °C in the air. The thermal expansion coefficient (TEC) in all samples was ca. 11–15 × 10⁻⁶/°C at 200–800 °C. After an aging treatment at 700 °C for a holding time of 1000 h, the conductivities of all samples showed almost no change. However, the conductivity in Ce_0.8Sm_0.15Ca_0.05O_2−δ decreased from 0.0837 to 0.0581 S/cm, and the grain size increased. The conductivities of the CeO₂-based specimens were also measured under a 5%H₂–95%N₂ atmosphere, and the conductivity greatly increased in the reducing atmosphere because the Ce⁴⁺ ions reduced to Ce³⁺ ions.     

Electrochemical synthesis of ammonia from N2 and H2O based on (Li,Na,K)2CO3–Ce0.8Gd0.18Ca0.02O2−δ composite electrolyte and CoFe2O4 cathode

Electrochemical synthesis of ammonia from water vapour and nitrogen was investigated using an electrolytic cell based on CoFe₂O₄–Ce0_.8Gd_0.18Ca_0.02O_2−δ (CFO-CGDC), CGDC-ternary carbonate composite and Sm_0.5Sr_0.5CoO_3−δ–Ce_0.8Gd_0.18Ca_0.02O_2−δ (SSCo-CGDC) as cathode, electrolyte and anode respectively. CoFe₂O₄, CGDC and SCCo were prepared via a combined EDTA-citrate complexing sol–gel and characterised by X-ray diffraction (XRD). The AC ionic conductivities of the CGDC-carbonate composite were investigated under three different atmospheres (air, dry O₂ and wet 5% H₂–Ar). A tri-layer electrolytic cell was fabricated by a cost-effective one-step dry-pressing and co-firing process. Ammonia was successfully synthesised from water vapour and nitrogen under atmospheric pressure and the maximum rate of ammonia production was found to be 6.5 × 10⁻¹¹ mol s⁻¹ cm⁻² at 400 °C and 1.6 V which is two orders of magnitude higher than that of previous report when ammonia was synthesised from N₂ and H₂O at 650 °C.     

Hydrogen production aided by new (1−x)SrTi0.5Fe0.5O3–δ–xCe0.8(Sm0.8Sr0.2)0.2O2–δ (MIEC) composite membranes

In the present work, composite materials of the type (1–x)SrTi_0.5Fe_0.5O_3–δ–xCe_0.8(Sm_0.8Sr_0.2)_0.2O_2–δ (with х = 0, 0.25, 0.5, 0.75 and 1) are obtained by the two step solid state technique. Their transport properties are investigated in terms of their usage as mixed ionic-electronic conducting (MIEC) membrane materials for hydrogen production. It is found that, in reducing conditions the composites are characterized by mixed conductivity, which level is controlled by the electrical properties of the prevailing phase. Moreover, at 900 °C and pO₂ = 10⁻¹⁸ atm, total conductivity, ambipolar conductivity and oxygen permeability of composites dramatically grow (each of about 500%), when the fluorite component content x increases from 0 to 1. High-conducting and strengthened material 0.5SrTi_0.5Fe_0.5O_3–δ–0.5Ce_0.8(Sm_0.8Sr_0.2)_0.2O_2–δ is chosen for making tube shaped membranes using the tape rolling method, which are successfully applied for hydrogen production in laboratory scale. The hydrogen flux reached 0.176 ml cm⁻² min⁻¹ for x = 1, T = 900 °C and emf = 10 mV.     

High performance intermediate temperature micro-tubular SOFCs with Ba0.9Co0.7Fe0.2Nb0.1O3−δ as cathode

In this study, anode supported intermediate temperature micro-tubular solid oxide fuel cells (MT-SOFCs) have been fabricated by combination of phase-inversion, dip-coating, co-sintering and printing method. The MT-SOFC consists of a ∼300 μm wall-thickness Ni–Sc₂O₃ stabilized ZrO₂ (ScSZ) anode tube, ∼10 μm ScSZ dense electrolyte layer, ∼10 μm Ce_0.9Gd_0.1O_2−δ (GDC) membrane buffer layer and ∼50 μm Ba_0.9Co_0.7Fe_0.2Nb_0.1O_3−δ (BCFN) cathode layer. SEM and electrochemical impedance spectroscopy (EIS) analysis suggested that the novel structured anode can remarkably diminish the porous anode geometrical tortuosity and improve the fuel gas diffusivity. High peak power densities of 0.34, 0.51 and 0.72 W cm⁻² have been achieved with humidified hydrogen as the fuel and ambient air as oxidant at 550, 600 and 650 °C, respectively. Further, the cell has demonstrated a very stable performance with no significant cell voltage degradation under a constant current of 0.6 A cm⁻² for over 213 h test at 650 °C.     

Preparation and characterization of Ba0.5Sr0.5Fe0.9Ni0.1O3−δ–Sm0.2Ce0.8O1.9 compose cathode for proton-conducting solid oxide fuel cells

A cobalt-free Ba_0.5Sr_0.5Fe_0.9Ni_0.1O_3−δ–Sm_0.2Ce_0.8O_1.9 (BSFN–SDC) composite was employed as a cathode for proton-conducting solid oxide fuel cells (H-SOFCs) using BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) as the electrolyte. The chemical compatibility between BSFN and SDC was evaluated. The XRD results showed that BSFN was chemically compatible with SDC after co-fired at 1100 °C for 5 h. The thermal expansion coefficient (TEC) of BSFN–SDC, which showed a reasonably reduced value (16.08 × 10⁻⁶ K⁻¹), was effectively decreased due to Ce_0.8Sm_0.2O_1.9 (SDC) added. A single cell of Ni–BZCY/Ni–BZCY/BZCY/BSFN–SDC with a 25-μm-thick BZCY electrolyte membrane exhibited excellent power densities as high as 361.8 mW cm⁻² at 700 °C with a low polarization resistance of 0.174 Ω cm². The excellent performance implied that the cobalt-free BSFN–SDC composite was a promising alternative cathode for H-SOFCs.     

Electrochemical performance of a copper-impregnated Ni–Ce0.8Sm0.2O1.9 anode running on methane

Ni–Cu–Ce_0.8Sm_0.2O_1.9 anode-supported single cells were developed for the direct utilization of methane. An yttria-doped zirconia and Ce_0.8Sm_0.2O_1.9 bi-layer electrolyte and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3 − δ cathode layer were fabricated by slurry spin-coating. Cu was added to the anode by impregnation with a nitrate solution. The effects of Cu on the electrochemical performance of the anode were investigated in dry methane with respect to times of impregnation. Impregnation with Cu twice was determined to be optimal. Incorporating Cu into the anode improved electrochemical performance of the cells, reducing ohmic resistance and suppressing carbon deposition. At 700 °C, the single cell exhibited a maximum power density of 406 mW/cm² in dry methane. At a current density of 500 mA/cm², the cell maintained 98.6% of its initial voltage after operation for 900 min.     

Improved oxygen permeability of Ce0.8Sm0.2O2−δ–PrBaCo2O5+δ dual-phase membrane by surface-modifying porous layer

A porous PrBaCo₂O_5+δ or Ce_0.8Sm_0.2O_2−δ–50 vol.% PrBaCo₂O_5+δ (SDC–PBCO (5/5)) layer was deposited on dense Ce_0.8Sm_0.2O_2−δ–40 vol.% PrBaCo₂O_5+δ (SDC–PBCO (6/4)) membrane (450 μm) to enhance the oxygen permeability by increasing the surface area contacting with air. The oxygen permeation flux was measured in the temperature range of 825–945 °C. The results revealed that the oxygen permeation performance of Ce_0.8Sm_0.2O_2−δ–PrBaCo₂O_5+δ membranes can be significantly enhanced by coating SDC–PBCO (5/5) porous layer alone on the surface of feed side. The thickness of modification layer has obvious effect on the permeability of surface modified membrane. The modification on the feed side has much better effect than that on the permeate side. At 945 °C, the oxygen permeation flux of dense SDC–PBCO (6/4) membrane modified by porous SDC–PBCO (5/5) layer is 3.56 × 10⁻⁷ mol cm⁻² s⁻¹, 26% higher than that of the unmodified one.     

Effect of Sm0.2Ce0.8O1.9 on the carbon coking in Ni-based anodes for solid oxide fuel cells running on methane fuel

To directly use hydrocarbon fuel without a reforming process, a new microstructure for Ni/Sm_0.2Ce_0.8O_2−δ (Ni/SDC) anodes, in which the Ni surface of the anode is covered with a porous Sm_0.2Ce_0.8O_2−δ thin film, was investigated as an alternative to conventional Ni/YSZ anodes. The porous SDC thin layer was coated on the pores of the anode using the sol–gel coating method. The cell performance was improved by 20%–25% with the Ni/SDC anode relative to the cell performance with the Ni/YSZ anode due to the high ionic conductivity of the Ni/SDC anode and the increase of electrochemical reaction sites. For the SDC-coated Ni/SDC anode operating with methane fuel, no significant degradation of the cell performance was observed after 180 h due to the surface modification with the SDC film on the Ni surface, which opposes the severe degradation of the cell performance that was observed for the Ni/YSZ anode, which results from carbon deposition by methane cracking. Carbon was hardly detected in the SDC-coated Ni/SDC anode due to the catalytic oxidation of the deposited carbon on the SDC film as well as the electrochemical oxidation of methane in the triple-phase-boundary.     

Electrochemical performance of La0.7Sr0.3CuO3−δ–Sm0.2Ce0.8O2−δ functional graded composite cathode for intermediate temperature solid oxide fuel cells

The fabrication and electrochemical properties of graded La_0.7Sr_0.3CuO_3−δ–Sm_0.2Ce_0.8O_2−δ (LSCu–SDC) composite cathodes were investigated in this paper. The phase composition, microstructure and electrochemical properties of the electrodes were characterized using X-ray diffraction (XRD), electron microscopy, electrochemical impedance spectroscopy (EIS) and cathodic polarization examinations. The results showed that the triple-layer graded cathode had super electrochemical performance comparing with the monolayer cathode. The graded LSCu–SDC cathode showed a polarization resistance of 0.094 Ωcm², a value much lower than the monolayer LSCu cathode of 0.234 Ωcm² at 800 °C in air. The current density of the graded cathode was 0.341 A cm⁻², more than double higher than monolayer LSCu of 0.146 A cm⁻² at an overpotential of 30 mV. The improved electrochemical performance could be attributed to the improved physical and chemical compatibility of the cathode layers in graded compositions with SDC electrolyte as well as the enlargement of triple-phase boundary for oxygen reduction.     

(La,Pr)0.8Sr0.2FeO3−δ–Sm0.2Ce0.8O2−δ composite cathode for proton-conducting solid oxide fuel cells

Mixed rare-earth (La, Pr)_0.8Sr_0.2FeO_3−δ–Sm_0.2Ce_0.8O_2−δ (LPSF–SDC) composite cathode was investigated for proton-conducting solid oxide fuel cells based on protonic BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) electrolyte. The powders of La_0.8−xPr_xSr_0.2FeO_3−δ (x = 0, 0.2, 0.4, 0.6), Sm_0.2Ce_0.8O_2−δ (SDC) and BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) were synthesized by a citric acid-nitrates self-propagating combustion method. The XRD results indicate that La_0.8−xPr_xSr_0.2FeO_3−δ samples calcined at 950 °C exhibit perovskite structure and there are no interactions between LPSF0.2 and SDC at 1100 °C. The average thermal expansion coefficient (TEC) of LPSF0.2–SDC, BZCY and NiO-BZCY is 12.50 × 10⁻⁶ K⁻¹, 13.51 × 10⁻⁶ K⁻¹ and 13.47 × 10⁻⁶ K⁻¹, respectively, which can provide good thermal compatibility between electrodes and electrolyte. An anode-supported single cell of NiO-BZCY|BZCY|LPSF0.2–SDC was successfully fabricated and operated from 700 °C to 550 °C with humidified hydrogen (∼3% H₂O) as fuel and the static air as oxidant. A high maximum power density of 488 mW cm⁻², an open-circuit potential of 0.95 V, and a low electrode polarization resistance of 0.071 Ω cm² were achieved at 700 °C. Preliminary results demonstrate that LPSF0.2–SDC composite is a promising cathode material for proton-conducting solid oxide fuel cells.     

Synthesis and sintering of Gd-doped CeO2 electrolytes with and without 1 at.% CuO dopping for solid oxide fuel cell applications

Nano-sized Ce_0.8Gd_0.2O_2−δ and Ce_0.79Gd_0.2Cu_0.01O_2−δ electrolyte powders were synthesized by the polyvinyl alcohol assisted combustion method, and then characterized by powder characteristics, sintering behaviors and electrical properties. The results demonstrate that the as-synthesized Ce_0.8Gd_0.2O_2−δ and Ce_0.79Gd_0.2Cu_0.01O_2−δ possessed similar powder characteristics, including cubic fluorite crystalline structure, porous foamy morphology and agglomerated secondary particles composed of gas cavities and primary nano crystals. Nevertheless, after ball-milling these two powders exhibited quite different sintering abilities. A significant reduction of about 400 °C in densification temperature of Ce_0.79Gd_0.2Cu_0.01O_2−δ was obtained when compared with Ce_0.8Gd_0.2O_2−δ. The Ce_0.79Gd_0.2Cu_0.01O_2−δ pellets sintered at 1000 °C and the Ce_0.8Gd_0.2O_2−δ sintered at 1400 °C exhibited relative densities of 96.33% and 95.7%, respectively. The sintering of Ce_0.79Gd_0.2Cu_0.01O_2−δ was dominated by the liquid phase process, followed by the evaporation-condensation process, Moreover, Ce_0.79Gd_0.2Cu_0.01O_2−δ shows much higher conductivity of 0.026 S cm⁻¹ than Ce_0.8Gd_0.2O_2−δ (0.0065 S cm⁻¹) at a testing temperature of 600 °C.     

Synthesis and electrical properties of Al-doped Sr2MgMoO6-δ as an anode material for solid oxide fuel cells

Aluminum doped Sr₂MgMoO_6-δ (SMMO) was synthesized via citrate-nitrate route. Dense samples of Sr₂Mg_1-xAl_xMoO_6−δ (0 ≤ x ≤ 0.05) were prepared by sintering the pellets at 1500 °C in air and then reducing at 1300 °C in 5%H₂/Ar. The electrical conductivity strongly depended on the preparing atmosphere, samples reduced in 5%H₂/Ar exhibited higher conductivity than those unreduced. Al-doping increased remarkably the electrical conductivity of Sr₂Mg_1-xAl_xMoO_6−δ. The reduced samples displayed a relatively stable electrical conductivity under oxygen partial pressure (Po₂) from 10⁻¹⁹ to 10⁻¹⁴ atm at 800 °C, and exhibited an excellent recoverability in electrical conductivity when cycled in alternative air and 5%H₂/Ar atmospheres. Sr₂Mg_0.95Al_0.05MoO_6−δ material showed a good chemical compatibility with LSGM and GDC electrolytes below 1000 °C, while there was an obvious reaction with YSZ. Al-doping improves the anode performance of SMMO in half-cell of Pt/Sr₂Mg_1-xAl_xMoO_6−δ∣GDC∣Pt in H₂ fuel. The present results demonstrate that Sr₂Mg_1-xAl_xMoO_6−δ is a potential anode material for intermediate temperature-Solid Oxide Fuel Cells (IT-SOFCs).     

Performance and degradation of La0.8Sr0.2Ga0.85Mg0.15O3−δ electrolyte-supported cells in single-chamber configuration

Electrolyte-supported cells were made of a La_0.8Sr_0.2Ga_0.85Mg_0.15O_3−δ (LSGM2015) electrolyte (200 μm thickness) prepared by ethylene glycol complex solution synthesis, isostatic pressing and sintered at 1400 °C, a Ni-SDC anode, a Sm_0.2Ce_0.8O_3−δ (SDC) buffer-layer between anode and electrolyte, and a La_0.5Sr_0.5CoO_3−δ-SDC cathode. The cells were tested in single-chamber configuration using methane–air mixtures. The results of X-ray diffraction and SEM-EDS showed a single-phase in the electrolyte and conductivities (∼0.01 S cm⁻¹ at 650 °C) close to the typical values. Good cell power densities of 215 and 102 mW cm⁻² were achieved under CH₄/O₂ = 1.4 of at 800 and 650 °C, respectively. However, the cell stability tests indicated that the operating temperature strongly influenced on the cell performance after 100 h. While no significant change in the power density was observed working at 650 °C, a clear performance degradation was evidenced at 800 °C. SEM-EDS revealed an appreciable degradation of the electrolyte and both the electrodes.     

Sm0.5Sr0.5CoO3–Ce1.8Sm0.2O1.9 electrodes enhanced by Sm0.5Sr0.5CoO3 impregnation for proton conductor based solid oxide fuel cells

Sm_0.5Sr_0.5CoO_3−δ–Ce_0.8Sm_0.2O_2−δ (SSC–SDC) composites, which are often used as the cathodes for solid oxide fuel cells (SOFCs) with oxygen-ion conducting electrolytes, have been recently shown to be also applicable in SOFCs based on proton conductors such as BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY). The electrochemical performances of blank SSC–SDC electrodes on BZCY electrolytes are substantially improved in this work by impregnating SSC nanoparticles additionally. When the loading increases, the interfacial polarization resistance of the symmetric cell decreases gradually at first, notably when it exceeds 14 wt.%, and to the lowest value at about 22 wt.%. Furthermore, impregnating SSC reduces the low-frequency-arc resistance that corresponds to the surface exchange step. In addition, impregnating SSC reduces the activation energy for oxygen reduction from 1.14 to 0.70 eV, thus resulting in significantly improvement on electrode performance at the reduced temperatures for SOFCs based on proton conductors.     

A cobalt-free Sm0.5Sr0.5FeO3−δ–BaZr0.1Ce0.7Y0.2O3−δ composite cathode for proton-conducting solid oxide fuel cells

A cobalt-free Sm_0.5Sr_0.5FeO_3−δ–BaZr_0.1Ce_0.7Y_0.2O_3−δ (SSF–BZCY) was developed as a composite cathode material for proton-conducting solid oxide fuel cells (H-SOFC) based on proton-conducting electrolyte of stable BZCY. The button cells of Ni-BZCY/BZCY/SSF–BZCY were fabricated and tested from 550 to 700 °C with humidified H₂ (～3% H₂O) as a fuel and ambient oxygen as oxidant. An open-circuit potential of 1.024 V, maximum power density of 341 mW cm⁻², and a low electrode polarization resistance of 0.1 Ω cm² were achieved at 700 °C. The experimental results indicated that the SSF–BZCY composite cathode is a good candidate for cathode material.     

Characterization of nanosized Ce0.8Sm0.2O1.9-infiltrated Sm0.5Sr0.5Co0.8Cu0.2O3−δ cathodes for solid oxide fuel cells

This study investigates the microstructure and electrochemical properties of Sm_0.5Sr_0.5Co_0.8Cu_0.2O_3−δ (SSC-Cu) cathode infiltrated with Ce_0.8Sm_0.2O_1.9 (SDC). The newly formed nanosized electrolyte material on the cathode surface, leading the increase in electrochemical performances is mainly attributed to the creation of electrolyte/cathode phase boundaries, which considerably increases the electrochemical sites for oxygen reduction reaction. Based on the experiment results, the 0.4 M SDC infiltration reveals the lowest cathode polarization resistance (R_P), the cathode polarization resistances (R_p) are 0.117, 0.033, and 0.011 Ω cm² at 650, 750, and 850 °C, and the highest peak power density, are 439, 659, and 532 mW cm⁻² at 600, 700, and 800 °C, respectively. The cathode performance in SOFCs can be significantly improved by infiltrating nanoparticles of SDC into an SSC-Cu porous backbone. This study reveals that the infiltration approach may apply in SOFCs to improve their electrochemical properties.     

Prontonic ceramic membrane fuel cells with layered GdBaCo2O5+x cathode prepared by gel-casting and suspension spray

In order to develop a simple and cost-effective route to fabricate protonic ceramic membrane fuel cells (PCMFCs) with layered GdBaCo₂O_5+x (GBCO) cathode, a dense BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) electrolyte was fabricated on a porous anode by gel-casting and suspension spray. The porous NiO–BaZr_0.1Ce_0.7Y_0.2O_3−δ (NiO–BZCY7) anode was directly prepared from metal oxide (NiO, BaCO₃, ZrO₂, CeO₂ and Y₂O₃) by a simple gel-casting process. A suspension of BaZr_0.1Ce_0.7Y_0.2O_3−δ powders synthesized by gel-casting was then employed to deposit BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY7) thin layer by pressurized spray process on NiO–BZCY7 anode. The bi-layer with 10 μm dense BZCY7 electrolyte was obtained by co-sintering at 1400 °C for 5 h. With layered GBCO cathode synthesized by gel-casting on the bi-layer, single cells were assembled and tested with H₂ as fuel and the static air as oxidant. An open-circuit potential of 0.98 V, a maximum power density of 266 mW cm⁻², and a low polarization resistance of the electrodes of 0.16 Ω cm² was achieved at 700 °C.     

SmBa0.5Sr0.5Cu2O5+δ and SmBa0.5Sr0.5CuFeO5+δ layered perovskite oxides as cathodes for IT-SOFCs

Novel Cobalt-free layered perovskite oxides SmBa_0.5Sr_0.5Cu₂O_5+δ (SBSCO) and SmBa_0.5Sr_0.5CuFeO_5+δ (SBSCFO) were investigated as cathode materials for intermediate-temperature solid fuel cells (IT-SOFCs). The thermal expansion coefficients (TEC) of SBSCO and SBSCFO were 14.1 × 10⁻⁶/°C and 14.9 × 10⁻⁶/°C in 50 °C–800 °C, which were more compatible with electrolyte than cobalt-based cathodes. When A′-site is partially substituted by Sr, the conductivity of SBSCO and SBSCFO had been improved. The max electrical conductivity of SBSCO was 277.7 S cm⁻¹, about one order of magnitude higher than SmBaCu₂O_5+δ. Polarization resistance of SBSCO is 0.25 Ω cm² at 650 °C, which is twice lower than that of SmBaCu₂O_5+δ (SBCO). This implies SBSCO has higher activity for oxygen reduction than SBCO. Preliminary results indicate that SBSCO are promising as cathodes for IT-SOFCs.     

Syngas production at intermediate temperature through H2O and CO2 electrolysis with a Cu-based solid oxide electrolyzer cell

Solid Oxide Electrolyzer Cells (SOECs) are promising energy devices for the production of syngas (H₂/CO) by H₂O and/or CO₂ electrolysis. Here we developed a Cu–Ce_0.9Gd_0.1O_2−δ/Ce_0.8Gd_0.2O_2−δ/Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ-Ce_0.8Gd_0.2O_2−δ cell and performed H₂O and CO₂ electrolysis experiments in the intermediate temperature range (600°C–700 °C). As a baseline, the cell was first tested in fuel cell operation mode; the sample shows a maximum power density peak of 104 mW cm⁻² at 700 °C under pure hydrogen and air. H₂O electrolysis testing revealed a steady production of hydrogen with a Faraday's efficiency of 32% at 700 °C at an imposed current density of −78 mA cm⁻². CO production was observed during CO₂ electrolysis but higher cell voltages were required. A lower efficiency of about 4% was obtained at 700 °C at an imposed current density of −660 mA cm⁻². These results confirm that syngas production is feasible by water and carbon dioxide electrolysis but further improvements from both the manufacturing and the electrocatalytic aspects are needed to reach higher yields and efficiencies.     

Investigation of cobalt-free cathode material Sm0.5Sr0.5Fe0.8Cu0.2O3−δ for intermediate temperature solid oxide fuel cell

A cobalt-free cubic perovskite oxide Sm_0.5Sr_0.5Fe_0.8Cu_0.2O_3−δ (SSFCu) was investigated as a novel cathode for intermediate temperature solid oxide fuel cells (IT-SOFCs). The thermal expansion coefficient (TEC) of SSFCu was close to that of Sm_0.2Ce_0.8O_1.9(SDC) electrolyte and the electrical conductivity of SSFCu sample reached 72–82 S cm⁻¹ in the commonly operated temperatures of IT-SOFCs (400–600 °C). Symmetrical electrochemical cell with the configuration of SSFCu/SDC/SSFCu was applied for the impedance study and area specific resistance (ASR) of SSFCu cathode material was as low as 0.085 Ω cm² at 700 °C. Laboratory-sized tri-layer cells of NiO-SDC/SDC/SSFCu were operated from 450 to 700 °C with humidified hydrogen (∼3% H₂O) as fuel and the static air as oxidant. A maximum power density of 808 mW cm² was obtained at 700 °C for the single cell.