Biobased Contents of Organic Fillers and Polycaprolactone Composites with Cellulose Fillers Measured by Accelerator Mass Spectrometry Based on ASTM D6866

The biobased contents of raw materials such as starches, sugar, chitin, or wood powders for biomass plastics were measured using Accelerator Mass Spectrometry (AMS) based on ASTM D6866. AMS measures the isotope carbon ratio of ¹⁴C to ¹²C and ¹³C in graphite derived from sample powders. The biobased contents of starches, sugar or chitin were almost 100% which means that they are fully biobased. The biobased contents of the wood powders were over 140% due to the effect of the post 1950s ¹⁴C injection due to nuclear testing. Poly(ε-caprolactone) (PCL) composite samples were prepared using the polymerization and direct molding method. The starting compound was the ε-caprolactone monomer liquid combined with cellulose and inorganic fillers using aluminum triflate as a catalyst at 80 °C for 6 or 24 h. PCL cylinder-shaped composite samples with a homogeneously dispersed cellulose filler were prepared with M_n = 4,600 (M_w/M_n = 2.9). The biobased content of the PCL composite with 50 wt% cellulose filler (51.67%) measured using AMS was slightly higher than the carbon ratio of cellulose in the starting powder samples (41.3 mol%). This is due to the higher biobased content (112.70%) of the cellulose filler used in this study. The biobased content of the polymer composite powders by AMS was found not to be affected by the presence of inorganic fillers, such as talc.     

Dehydrochlorination behavior of polyvinyl chloride and utilization of carbon residue: effect of plasticizer and inorganic filler

The dehydrochlorination behavior of plasticizer (DOP) and inorganic filler (CaCO₃) contained in PVC samples and the properties of the activated carbons produced from those carbon residues have been investigated. In the dehydrochlorination process, both additives contributed not only to a decrease in HCl yield but also to the prolonged evolution of HCl. Part of the Cl species were observed to be stabilized as CaCl₂ by reaction with calcium ions when CaCO₃ was added. More than 80% of chlorine removal was achieved in all samples at 533 K. The use of potassium as an activation agent led to the production of activated carbon with a specific surface area greater than 1000 m²/g at the low temperature of 1023 K and assisted also in the elimination of residual Cl species by the formation of KCl during activation. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Biodegradable kinetics of plastics under controlled composting conditions

This study models and evaluates the kinetics of C-CO₂ evolution during biodegradation of plastic materials including Polyethylene (PE), PE/starch blend (PE/starch), microcrystalline cellulose (MCE), and Polylactic acid (PLA). The aerobic biodegradation under controlled composting conditions was monitorated according to ISO 14855-1, 2004. The kinetics model was based on first order reaction in series with a flat lag phase. A non-linear regression technique was used to analyze the experimental data. SEM studies of the morphology of the samples before and after biodegradation testing were used to confirm the biodegradability of plastics and the accuracy of the model. The work showed that MCE and PLA produced the high amounts of C-CO₂ evolution, which gave readily hydrolysable carbon values of 55.49% and 40.17%, respectively with readily hydrolysis rates of 0.338 day⁻¹ and 0.025 day⁻¹, respectively. Whereas, a lower amount of C-CO₂ evolution was found in PE/starch, which had a high concentration of moderately hydrolysable carbon of 97.74% and a moderate hydrolysis rate of 0.00098 day⁻¹. The mineralization rate of PLA was 0.500 day⁻¹ as a lag phase was observed at the beginning of the biodegradability test. No lag phase was observed in the biodegradability testing of the PE/starch and MCE. The mineralization rates of the PE/starch and MCE were found to be 1.000 day⁻¹, and 1.234 day⁻¹, respectively. No C-CO₂ evolution was observed during biodegradability testing of PE, which was used for reference as a non-biodegradable plastics sample.     

Effects of Temperature and Relative Humidity on Polylactic Acid Plastic Degradation

Three high molecular weight (120,000 to 200,000 g mol^–1) polylactic acid (PLA) plastic films from Chronopol (Ch-I) and Cargill Dow Polymers (GII and Ca-I) were analyzed for their degradation under various temperature and relative humidity (RH) conditions. Two sets of plastic films, each containing 11 samples, were randomly hung in a temperature/humidity-controlled chamber by means of plastic-coated paper clips. The tested conditions were 28, 40, and 55°C at 50 and 100% RH, respectively, and 55°C at 10% RH. The three tested PLA films started to lose their tensile properties when their weight-average molecular weight (M _w) was in the range of 50,000 to 75,000 g mol^–1. The average degradation rate of Ch-I, GII, and Ca-I was 28,931, 27,361, and 63,025 M _w/week, respectively. Hence, GII had a faster degradation rate than Ch-I and Ca-I under all tested conditions. The degradation rate of PLA plastics was enhanced by the increase in temperature and relative humidity. This trend was observed in all three PLA plastics (Ca-I, GII, and Ch-I). Of the three tested films, Ch-I was the first to lose its mechanical properties, whereas Ca-I demonstrated the slowest loss, with mechanical properties under all tested conditions.     

Photodegradation and Biodegradation Study of a Starch and Poly(Lactic Acid) Coextruded Material

To simulate the behavior of agricultural mulch coextruded poly(lactic acid)(PLA)/starch films, two stages were carried out. The first was an ultraviolet treatment (UV) at 315 nm, during which glass transition temperature T_g, weight, and molecular weight (MW) decreased and a separation between PLA and starch phase was observed. For the second stage, the mineralization of the carbon of the material was followed using the ASTM (D 5209–92 and 5338–92) and ISO/CEN (14852 and 14855) standard procedures. To measure the biodegradability of polymer material, the assessment of the carbon balance allowed determination of the distribution between the carbon rate used to the biomass synthesis or the respiration process (released CO₂), as well as the dissolved organic carbon into the culture medium and the carbon in the residual insoluble material. The influence of the nature of the medium and the standardized procedures on the final rate of biodegradation was investigated. Whatever the standardized method, the biodegradation percentage was significantly stronger in liquid medium (92.4–93.4) than on inert medium (80–83%). In the case of the compost process, only released CO₂ was measured and corresponded to 79.1–80.3%.     

Effect of Nucleating Agents on Physical Properties of Poly(lactic acid) and Its Blend with Natural Rubber

Poly(lactic acid) (PLA) presents high strength and modulus, but very low toughness as well as slow crystallization. Natural rubber (NR) was blended to enhance the toughness and nucleating agent was added to improve the crystallization. Cyclodextrin (CD), considered as a green compound, as well as calcium carbonate (CaCO₃) and talc were used as nucleating agents. Effects of these nucleating agents on crystallization, mechanical properties and morphology of neat PLA and PLA/NR blend were investigated. It was found that the addition of talc and CD decreased cold crystallization temperature (T_cc) of the PLA. Same result was obtained in PLA/NR blend containing talc. All nucleating agents increased the degree of crystallinity (Χ_C) of PLA, whereas only talc and CaCO₃ increased Χ_C of PLA in PLA/NR blends. The enhanced toughness of PLA by the addition of nucleating agent was attributed to its increased crystallinity, as well as decreased spherulite size. For PLA/NR blends, the increase in toughness was mainly contributed by the presence of the rubber.     

Biodegradable Composite Foams of PLA and PHBV Using Subcritical CO<Subscript>2</Subscript>

One key strategy for increasing the application potential for biodegradable plastics lies in improving the physical and mechanical characteristics, which can be attained by inducing a cellular morphology in the pure polymer with the aid of a blowing agent, as well as by blending two or more polymers with the desirable properties. This paper examines the effect that blending two biodegradable polymers has on the thermal properties and morphology of the resultant foams blown with carbon dioxide (CO₂). Polylactic acid (PLA), polyhydroxybutyrate-co-valerate (PHBV) and blends of both were foamed and characterized in terms of thermal characteristics, relative density, cell size, and foam morphology. The results indicate that although PLA and PHBV are immiscible, the presence of small quantities of PHBV (25 wt%) could lead to low density foams with finer, more uniform cells. Furthermore, the crystallinity of PHBV was found to be unaffected by the presence of PLA in the composite, which supports the immiscibility of PLA and PHBV.     

Carbon materials-catalyzed hydroliquefaction of flame-retardant plastics in organic solvents

Flame-retardant plastics, such as desktop and laptop personal computer bodies, could be completely liquefied by carbon materials-catalyzed hydroliquefaction in tetralin without using H₂ as a hydrogen source. Active carbons with larger surface areas (1450–3450 m²/g) acted as superior catalysts in transferring tetralin hydrogens to plastics. On the other hand, carbon blacks and fullerene-rich soot were less active catalysts. Graphite and mesocarbon microbeads did not show any catalytic effects. Benzene, toluene, and ethylbenzene were obtained as recyclable hydrocarbons; their total amounts varied from 4 wt% to 12 wt% depending on the types of plastics and the carbon materials used. Organic bromides such as polybromodioxins were not contained in the gases and oils of the product. Received: July 19, 2000 / Accepted: September 17, 2000     

Aerobic biometer analysis of glucose and starch biodegradation

The ASTM D5210-91 protocol for evaluating the biodegradability of a polymer was examined. The reactor design was modified not only to account for the total CO₂ evolved but also to allow for the simultaneous carbon assessment in microbes, soluble products, and solid samples. Improvements in the test procedure were implemented such as (1) refining the CO₂ pretrap and posttrap design, (2) optimizing the carbon dioxide removal efficiency, (3) accounting for the total polymeric carbon, (4) standardizing the inoculum, and (5) revising the nutrient medium. By growing the sludge on a suitable substrate prior to polymeric exposure, a constant microbial density was obtained. The modified ASTM method provides an assessment of the polymeric carbon degradation at any given time. The results of this work have specific significance to the behavior of polymers in a sewage waste treatment plant, where sludge is continuously being acrated, and also for aerobic biodegradation in general.     

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO<Subscript>2</Subscript> Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO₂ composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO₂ composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO₂ (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO₂ composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m². PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.     

Influence of Processing Additives on the Degradation of Melt-Pressed Films of Poly(ε-Caprolactone) and Poly(Lactic Acid)

Melt-pressed films of polycaprolactone (PCL) and poly(lactic acid) (PLA) with processing additives, CaCO₃, SiO₂, and erucamide, were subjected to pure fungal cultures Aspergillus fumigatus and Penicillium simplicissimum and to composting. The PCL films showed a rapid weight loss with a minor reduction in the molecular weight after 45 days in A. fumigatus. The addition of SiO₂ to PCL increased the rate of (bio)erosion in A. fumigatus and in compost. The use of a slip additive, erucamide, was shown to modify the properties of the film surface without decreasing the rate of bio(erosion). Both the rate of weight loss and the rate of molecular weight reduction of PCL increased with decreasing film thickness. The addition of CaCO₃ to PLA significantly reduced the thermal degradation during processing, but it also reduced the rate of the subsequent (bio)degradation in the pure fungal cultures. PLA without additives and PLA containing SiO₂ exhibited the fastest (bio)degradation, followed by PLA with CaCO₃. The degradation of the PLA films was initially governed by chemical hydrolysis, followed by an acceleration of the weight change and of the molecular weight reduction. PLA film subjected to composting exhibits a rapid decrease in molecular weight, which then remains unchanged during the measurement period, probably because of crystallization.     

Radiation Crosslinking of Poly(Butylene Succinate) in the Presence of Inorganic Material and Its Biodegradability

Three kinds of poly(butylene succinate)s (PBS) with different molecular weight were irradiated with electron beams in the presence of inorganic material. Fourteen kinds of inorganic materials were used in this work. The presence of inorganic material inside cross-linked PBS samples enhances the yield of gel formation. The heat stabilities of PBS samples were checked; it was found that silicon dioxide and carbon black significantly improve these properties. Enzymatic and soil burial tests were performed; the presence of these inorganic materials in cross-linked PBS accelerates the rate of biodegradation.     

Degradation of Starch–Calcium Carbonate Disposable Packaging in a Solid Waste Composting Facility

The compostability of starch–CaCO₃ disposable packaging was examined in a source-separated municipal solid waste (MSW) composting facility located in East Hampton, NY. Source-separated MSW:starch–CaCO₃ container mixtures of 0 (control), 5, and 20% (by volume) were prepared as feedstock for composting. Compost samples were collected weekly or biweekly during the composting process and examined for fragments of the starch–CaCO₃ containers. Changes in compost quality due to the presence of starch–CaCO₃ containers were assessed by measuring the nutrient and metal content of the three resultant MSW:starch–CaCO₃ composts. Finally, plant growth studies were conducted to examine the composts for possible plant growth inhibition due to the deterioration of the starch–CaCO₃ containers. Results showed that portions of the starch–CaCO₃ containers were not identified in any of the 5 and 20% sieved and characterized compost fractions > 1.3 cm following 1–3 weeks of composting. Mechanical agitation of the waste along with optimum composting conditions were sufficient to initiate the rapid degradation of the starch–CaCO₃ composites. Degradation of starch–CaCO₃ containers did not affect compost nutrient and trace element content. Grass biomass measurements were performed once weekly over 28 days for grass grown in control (0%), 5%, and 20% starch–CaCO₃-containing compost:soil mixtures. Significant differences in grass biomass for these compost:soil mixtures were measured only for the 0 and 20% starch–CaCO₃-containing compost:soil mixtures at 28 days (9.07 vs 11.05 g, respectively; P = 0.046).     

Temperature Effects on Soil Mineralization of Polylactic Acid Plastic in Laboratory Respirometers

A respirometric system was used to analyze the biodegradation of high molecular weight (120,000 to 200,000 g mol^–1) polylactic acid (PLA) plastic films in soil under laboratory conditions. The respirometric system consisted of air-conditioning pretraps, a soil reactor, and a carbon dioxide (CO₂) posttrap. A 200-g homogeneous soil mixture of all-purpose potting soil : manure soil : sand [1 : 1 : 1 (w/w)] and 1.5 g of PLA plastic films in 1 × 1-cm² squares was added to each bottle. The respirometers were placed in a 28, 40, or 55°C water bath for 182 days. Treatments (three replicates) included native corn starch (positive control), polyethylene (Glad Cling Wrap; negative control), and three PLA films: Ca-I (Cargill Dow Polymers LLC, monolayer), GII (Cargill Dow Polymers LLC, Generation II), and Ch-I (Chronopol; monolayer). The degree of polymer mineralization was indicated by the cumulative CO₂ liberated from each respirometer. The initial average mineralization rate and total percentage mineralized of the PLA plastic films at 28, 40, and 55°C was 24.3, 41.5, and 76.9 mg/day with a 27, 45, and 70% carbon loss, respectively. No decrease in soil pH was observed after 182 days of mineralization. Hence, increase in soil temperature drastically enhanced the biodegradation of PLA plastic films in soil under laboratory conditions (P < 0.0001).     

Gasification of waste plastics by steam reforming in a fluidized bed

The process of producing synthetic gas from waste plastics by steam reforming was investigated. To evaluate this process, the steam reforming of the oils derived from low-density polyethylene and polystyrene were carried out using a laboratory-scale fluidized bed of Ni-Al₂O₃ catalysts. The performance of gasification in terms of carbon conversion, gas yield, and gas compositions was examined. Although oils derived from plastics contain many kinds of heavy hydrocarbons and aromatics, they were well gasified at temperatures above 1023 K with a steam/carbon ratio of 3.5 and a weight hourly space velocity of 1 h⁻¹. The hydrogen content of the product gas was very high at approximately 72 vol% for polyethylene-derived oil and 68 vol% for polystyrene-derived oil. These compositions agreed well with the values calculated from chemical equilibrium.     

Aging of Toughened Polylactic Acid Nanocomposites: Water Absorption,Hygrothermal Degradation and Soil Burial Analysis

The environmental aging behaviour of montmorillonite (MMT) filled polylactic acid (PLA) nanocomposites (PLA/MMT) and linear low density polyethylene (LLDPE)-toughened PLA (PLA/LLDPE ratio = 90/10) nanocomposites (PLA/LLDPE/MMT) were investigated in this study. The nanocomposites were subjected to water absorption, hygrothermal degradation and soil burial analysis. Both PLA/MMT and PLA/LLDPE/MMT nanocomposites were immersed in distilled water at three different temperatures (room temperature, 60, and 90 °C) and the weight difference before and after immersion was calculated. The kinetics of water absorption for both nanocomposites followed the Fick’s second law of diffusion, where a linear relationship exists between the initial moisture absorption at any time t and t ^1/2 (the square root of time), followed by a horizontal plateau (saturation). The equilibrium moisture content (M _m ) and diffusion coefficient (D) of PLA nanocomposites increased with the addition of MMT (2 phr) and LLDPE. However, the D values of both nanocomposites decreased by increasing MMT (4 phr). The M _m for PLA/MMT and PLA/LLDPE/MMT nanocomposites increased by increasing immersion temperature (60 °C) and prolonged immersion resulted in hygrothermal degradation of both nanocomposites. The hygrothermal degradation studies showed that PLA degrades much faster at 90 °C as compared to 60 °C in both the nanocomposites. The addition of MMT and LLDPE improved the hygrothermal stability of PLA in both nanocomposites. Soil burial test revealed deterioration of impact strength in all samples while the rate of biodegradation was retarded in the presence of MMT and LLDPE.     

Comparison of Polylactic Acid/Kenaf and Polylactic Acid/Rise Husk Composites: The Influence of the Natural Fibers on the Mechanical, Thermal and Biodegradability Properties

This paper investigates and compares the performances of polylactic acid (PLA)/kenaf (PLA-K) and PLA/rice husk (PLA-RH) composites in terms of biodegradability, mechanical and thermal properties. Composites with natural fiber weight content of 20% with fiber sizes of less than 100 μm were produced for testing and characterization. A twin-screw extrusion was used to compound PLA and natural fibers, and extruded composites were injection molded to test samples. Flexural and Izod impact test, TGA, soil burial test and SEM were used to investigate properties. All results were compared to a pure PLA matrix sample. The flexural modulus of the PLA increased with the addition of natural fibers, while the flexural strength decreased. The highest impact strength (34 J m⁻¹), flexural modulus (4.5 GPa) and flexural strength (90 MPa) were obtained for the composite made of PLA/kenaf (PLA-K), which means kenaf natural fibers are potential to be used as an alternative filler to enhance mechanical properties. On the other hand PLA-RH composite exhibits lower mechanical properties. The impact strength of PLA has decreased when filled with natural fibers; this decrease is more pronounced in the PLA-RH composite. In terms of thermal stability it has been found that the addition of natural fibers decreased the thermal stability of virgin PLA and the decrement was more prominent in the PLA-RH composite. Biodegradability of the composites slightly increased and reached 1.2 and 0.8% for PLA-K and PLA-RH respectively for a period of 90 days. SEM micrographs showed poor interfacial between the polymer matrix and natural fibers.     

Preparation and characterization of high surface area activated carbon from pine wood sawdust by fast activation with H<Subscript>3</Subscript>PO<Subscript>4</Subscript> in a spouted bed

Activated carbons were produced from waste pine wood sawdust using fast activation with H₃PO₄ in a spouted bed. In this study, activation temperature was set as 800 °C, and activation time ranged from 1 to 15 min. Experimental results show that sawdust impregnated with higher mass ratio of H₃PO₄ would be agglomerated in spouted bed, and difficult to fluidize. Therefore, an amount of quartz sand was added to assist for good fluidization. Fluidization of particle can improve the BET surface area or micropore volume of activated carbons. High BET surface area activated carbons can be obtained with activation time of only 1–5 min by combining the fluidization and H₃PO₄ fast activation. The obtained activated carbons contained developed pore structure and abundant surface functional groups (carboxyl, carbonyl and P-containing groups) by SEM–EDS, FTIR and XPS techniques. The particles of impregnation ratio of 1:1 can achieve fluidization without adding the quartz sand, which was convenient for experimental operation and even industrial production, and the BET surface area can reach more than 1000 m²/g in activation time of only 5 min.     

Cellulose Fiber/Bentonite Clay/Biodegradable Thermoplastic Composites

Adding cellulose fiber reinforcement can improve mechanical properties of biodegradable plastics, but fiber must be well dispersed to achieve any benefit. The approach to dispersing fiber in this study was to use aqueous gels of sodium bentonite clay. These clay-fiber gels were combined with powdered compostable thermoplastics and calcium carbonate filler. The composite was dried, twin-screw extruded, and injection molded to make thin parts for tensile testing. An experimental design was used to determine the effect of fiber concentration, fiber length, and clay concentration. Polybutylene adipate/terephthalate copolymer (PBAT) and 70/30 polylactic acid (PLA)/PBAT blend were the biodegradable plastics studied. The composite strength decreased compared to the thermoplastics (13 vs. 19 MPa for PBAT, 27 vs. 38 MPa for the PLA/PBAT blend). The composite elongation to break decreased compared to the thermoplastics (170% vs. 831% for PBAT, 4.9% vs. 8.7% for the PLA/PBAT blend). The modulus increased for the composites compared to the thermoplastic standards (149 vs. 61 MPa for PBAT, 1328 vs. 965 MPa for the PLA/PBAT blend). All composite samples had good water resistance.     

Assessing Aerobic Biodegradability of Plastics in Aqueous Environment by GC-Analyzing Composition of Equilibrium Gaseous Phase

Testing biodegradability of plastics under varied conditions of the environment as well as under laboratory conditions in accordance with valid international standards is very laborious, lengthy and often also economically demanding. For this reason, applicability was verified of gas chromatography to analyze gaseous phase when investigating the biodegradation course of plastics in an aqueous environment as an alternative to customary employed methods. A mathematical model of acid–basic CO₂ equilibrium in a gas–liquid system was worked out, enabling to determine quantity of produced CO₂ through chromatographic analysis of gaseous phase, in dependence on ratio of liquid and gas phase volumes (V _l/V _g) and on actual pH of liquid phase. Experimental conditions for organizing the tests were optimized. A ratio that proved suitable was V _l/V _g ≅ 0.1 at pH ≈ 7.1 of liquid phase. Under these test conditions, biodegradability of model samples, PHB, Gellan gum and Xanthan gum, was explored; course of biodegradation was studied through produced CO₂ (values ) determined by analyzing gaseous phase through gas chromatography on the one hand, and through customary “titration” procedure on the other. With water-soluble polymers, the decrement in dissolved organic carbon (values D _DOC) was also studied. Difference between values does not exceed 5%. The procedures in question are alternative “substituting” procedures for observing course of aerobic biodegradation of substances in an aqueous environment.