Gold nanoparticles-enhanced bisphenol A electrochemical biosensor based on tyrosinase immobilized onto self-assembled monolayers-modified gold electrode

A novel electrochemical sensor based on the immobilization of tyrosinase(tyr) onto gold nanoparticles(nano-Au) and thioctic acid amide(T-NH2) self-assembled monolayers(SAMs)-modified gold electrode has been developed for the determination of bisphenol A(BPA).It was found that the nano-Au could significantly enhance the electrochemical response of tyr/nano-Au/T-NH2/Au electrode to BPA,and the enhancement effect of nano-Au on the current response was also related to the enzyme.The results indicated that the biosensor could be used as a detector for BPA determination with a linear range from3.99 ×10-7mol/L to 2.34 ×10-4mol/L and a detection limit of 1.33×10-7mol/L.In addition,this biosensor showed good reproducibility.     

A Fluorescent Biosensor for Detection of Zearalenone

ABSTRACT

A fluorescent biosensor was developed on a KinExA^TM flow spectrofluorimeter for the near real-time detection of soluble zeaalenone.

Briefly, solutions of zearalenone and a monoclonal antibody directed against a protein conjugate of zearalenone, were incubated for thirty minutes to permit equilibrium binding to occur. The reaction mixture was then passed over a packed column of small beads (98 μm) whose surfaces were coated with a covalent conjugate of zearalenone and bovine serum albumin (BSA). Following a short wash with buffer to remove excess unbound primary reagents, the packed beads were subjected to a brief contact with fluorescein isothiocyanate-labeled polyclonal secondary antibody directed against the primary monoclonal, once again followed by a short wash. As this assay depends on the ability of soluble antigen to compete with immobilized antigen, increasing concentrations of zearalenone result in decreasing fluorescence observed on the bead pack. This assay is rapid (? 60 minutes) and can be adapted to various other analytes of interest.     

Two-dimensional TiO2 (001) nanosheets as an effective photo-assisted recyclable sensor for the electrochemical detection of bisphenol A

Electrochemical detection is an efficient method for the detection of Bisphenol A (BPA). Herein, a sensitive photo-electrochemical sensor based on two-dimensional (2D) TiO₂ (001) nanosheets was fabricated and then used for BPA electrochemical detection. Upon light irradiation, the 2D TiO₂ (001) nanosheets electrode provided a lower detection limit of BPA detection compared with an ambient electrochemical determination. The low detection limit is ∼5.37 nmol/L (S/N = 3). Furthermore, profiting from the photoelectric characteristics, the 2D TiO₂ (001) nanosheets electrode exhibits a nice regeneration property. After 45 min of light irradiation, the electrochemical signal was regenerated from 14.7% to 82.9% of the original signal at the 6^th cycle. This is attributed to the non-selective OH mediation produced by the 2D TiO₂ (001) nanosheets mineralizing anodic polymeric products and resuming surface reactive sites. This investigation indicates that photo-assistance is an efficient method to improve the electrochemical sensor for detecting BPA in water environments.     

Functional graphene-gold nano-composite fabricated electrochemical biosensor for direct and rapid detection of bisphenol A

In this research, the graphene with excellent dispersity is prepared successfully by introducing gold nanoparticle to separate the individual sheets. Various techniques are adopted to characterize the prepared graphene and graphene-gold nanoparticle composite materials. This fabricated new composite material is used as the support material to construct a novel tyrosinase based biosensor for detection of bisphenol A (BPA). The electrochemical performances of the proposed new enzyme biosensor were investigated by differential pulse voltammetry (DPV) method. The proposed biosensor exhibited excellent performance for BPA determination with a wide linear range (2.5 × 10⁻³–3.0 μM), a highly reproducible response (RSD of 2.7%), low interferences and long-term stability. And more importantly, the calculated detection limit of the proposed biosensor was as low as 1 nM. Compared with other detection methods, this graphene-gold nanoparticle composite based tyrosinase biosensor is proved to be a promising and reliable tool for rapid detection of BPA for on-site analysis of emergency BPA related pollution affairs.     

Comparative study of three immunoassays based on monoclonal antibodies for detection of the pesticide parathion-methyl in real samples

Three immunoassay systems: indirect, direct competitive enzyme-linked immunosorbent assay (IC-ELISA and DC-ELISA), fluorescence polarization immunoassay (FPIA) based on monoclonal antibodies for the detection of parathion-methyl (PM) were developed and optimized. Several PM derivatives (haptens) were conjugated to proteins and fluoresceinthiocarbamyl ethylenediamine (EDF) to obtain immunogens and competitors. The influence of immunogen and competitor structures on the assay performance was investigated. IC-ELISA was the most sensitive of all techniques developed, with a detection limit of 0.08 ng ml⁻¹, but assay time was the longest (3.5 h per 96-well microtitre plate). DC-ELISA was easier to perform and quicker (1.5 h per 96-well microtitre plate) but less sensitive than IC-ELISA (detection limit was 0.5 ng ml⁻¹). FPIA was the fastest and simplest (7 min per 10 samples) but the least sensitive (detection limit was 15 ng ml⁻¹) technique. The methods were characterized by high specificity and reproducibility. The cross-reactivity for parathion-ethyl was around 30-40% for IC-ELISA and FPIA, but significantly higher (125%) for DC-ELISA. The immunoassays were applied to the analysis of PM residues in different food and environmental matrices. Methanol extracts of vegetable, fruit and soil samples were used for the analysis. Recoveries for most spiked samples averaged between 85 and 110%. The methods developed can be used for screening of food and environmental samples for PM residues without complicated clean-up.     

The Most Active Oxidase-Mimicking Mn2O3 Nanozyme for Biosensor Signal Generation

Oxidase-mimicking nanozymes are more desirable than peroxidase-mimicking ones since H₂O₂ can be omitted. However, only a few nanomaterials are known for oxidase-like activities. In this work, we compared the activity of Mn₂O₃, Mn₃O₄ and MnO₂ and found that Mn₂O₃ had the highest oxidase activity. Interestingly, the activity of Mn₂O₃ was even inhibited by H₂O₂. The oxidase-like activity of Mn₂O₃ was not much affected by the presence of proteins such as bovine serum albumin (BSA), but the physisorption of antibodies to Mn₂O₃ was not strong enough to withstand the displacement by BSA. We then treated Mn₂O₃ with 3-aminopropyltriethoxysilane to graft an amine group, which was used to conjugate antibodies using glutaraldehyde as a crosslinker. A one-step indirect competitive ELISA (icELISA) was developed for the detection of isocarbophos, and an IC₅₀ of 261.7 ng/mL was obtained, comparable with the results of the standard two-step assay using horseradish peroxidase (HRP)-labeled antibodies. This assay has the advantage of significant timesaving for rapid detection of large amounts of samples. This work has discovered a highly efficient oxidase-mimicking nanozyme useful for various nano- and analytical applications.     

Efficient access to bisphenol A metabolites: Synthesis of monocatechol,mono-o-quinone,dicatechol, and di-o-quinone of bisphenol A

2-Iodoxybenzoic acid (IBX) oxidation of bisphenol A (BPA) is described. The selective production of either the mono-o-quinone or the di-o-quinone can be controlled by IBX stoichiometry. Isolated yields of quinone were greater than 80%. Previous synthesis of BPA-di-o-quinone using a large excess of Fremy’s salt produced only trace amounts of product. In addition to o-quinone products, both mono- and dicatechols of BPA can synthesize in high yield and isolated without chromatography. The more stable catechols can be quantitatively converted back to o-quinones using silver oxide oxidation in either acetone or DMF. These one-pot reactions provide access to four different BPA metabolites in high yield and significant scale.     

A highly sensitive method for detection of bisphenol A in water samples based on functionalised Fe3O4@SiO2@nylon66

A simple and sensitive method was developed for preconcentration and determination of bisphenol A (BPA) in environmental samples by high performance liquid chromatography (HPLC). The hydrophilic silicon-dioxide- and nylon66-functionalised magnetic material (Fe₃O₄@SiO₂@nylon66) was used as a sorbent for magnetic solid-phase extraction (MSPE). With the anhydrous microemulsion reaction, the Fe₃O₄@SiO₂@nylon66 had shown great characteristics such as good magnetic responsivity, water dispersibility and stability. Based on the materials, various extraction parameters including pH, extraction time, elution time, the number of sorbents, sample volume and elution times were optimised. The whole extraction procedure could be accomplished within 20 min and the materials could be used more than 10 times after regeneration. Under the optimised conditions, different types of water samples (Tap water, river water, sea water and underground water) were successfully analysed to verify the applicability of the proposed method. The recoveries of different samples ranged from 88.54% to 104.46%. An enrichment factor of 250 was achieved with 0.05 μg/L detection limit. Thus, the developed MSPE is a potential technique that can be used for water samples preconcentration or combined with other analytical methods for determination of BPA.     

Determination of ethoxylated bisphenol A dimethacrylate monomers in dental composites by micellar electrokinetic chromatography

Separation of monomeric constituents of ethoxylated bisphenol A (BIS-EMA) with between 2 and 15 ethoxy groups per phenol in the molecule was investigated with micellar electrokinetic chromatography at different volume percentages methanol in the background electrolyte (10 mM sodium dodecylsulfate, 100 mM borate–50 mM phosphate buffer, pH 7.0). The conditions allowed the differentiation of the lower from the higher BIS-EMA homologues and of isomers, and enabled the characterisation of commercial dental composite materials. The decay curve for the light induced radical polymerisation of BIS-EMA in composite specimens was determined. The content of leachable monomers after light curing was quantified, resulting in 6% of the initial value after the recommended curing time. The method is suited to determine monomer constituents in polymerised composite material in the ppm range.     

Application of multivariate analysis to the screening of molecularly imprinted polymers for bisphenol A

A key issue in the synthesis of molecularly imprinted polymers (MIPs) is the identification and optimisation of the main factors that affect the material structure and its molecular recognition properties. This paper describes the application of an experimental design and multivariate analysis method for the synthesis of bisphenol A (BPA)-selective MIPs. Six factors with a large impact on the MIP synthesis and its analytical performance have been optimised: the amount of template, the type and the percentage of functional and cross-linking monomers, the polymerisation method (i.e. thermal or UV initiation) and the porogenic solvent. The polymers have been prepared in small-scale (mini-MIPs) and, after careful removal of the template, their BPA rebinding capacity has been evaluated and related to the MIP composition. Among the two functional monomers tested, namely 4-vinylpyridine (4-vpy) and methacrylic acid (MAA), the former rendered the best selectivity for BPA analysis. The partial least squares (PLS) models revealed that the photoinitiated polymers with a 1:1 ratio of 4-vinylpyridine to cross-linker (EDMA or TRIM) yield the highest specific binding. Such procedure is time and cost effective and can be used as a general tool in the preparation of MIPs for different analytes.     

Photodegradation of bisphenol A polycarbonate

When bisphenol A polycarbonate is subjected to weathering conditions this polymer shows two different degradation mechanisms depending on the used irradiation wavelengths, i.e. photo-oxidation and photo-Fries rearrangement. The relative importance of these mechanisms in outdoor exposure conditions is still unknown. In this study bisphenol A polycarbonate is exposed to simulated weathering conditions. Different analysing techniques show that photo-oxidation is the most dominant degradation reaction. However, fluorescence spectroscopy shows that small amounts of photo-Fries rearrangement products are formed. With model compounds blended in polypropylene it is shown that the photo-Fries reaction increases the photo-oxidation rate, thus in PP the photo-Fries reaction can proceed through radical intermediates. However, this is not the case in PC, ageing at condition causing an increased photo-Fries reaction rate did not result in a higher oxidation rate. This implies that in PC the photo-Fries reaction does not initiate its oxidation and thus does not proceed through radicals.     

苦杏仁甙化学发光生物传感器

将具有分子识别功能的β－葡萄糖甙酶和能进行换能反应的Ｌｕｍｉｎｏｌ分别固定在壳质胺和大孔阴离子交换剂的柱中,组成流动注射系统。苦杏仁甙在β－葡萄糖甙酶催化下分解生成的ＣＮ＾－（分子识别反应）与溶解氧反应生成超氧阴离子自由基,继而同Ｌｕｎｉｎｌ反应产生化学发光（换能反应）。这一新型生物传感器的化学发光强度与苦杏杜甙量在１～２００ｕｇ之间呈良好线性关系,检出限为０．３ｕｇ,相对标准偏差为３．１％,并具     

Molecularly imprinted polyethersulfone microspheres for the binding and recognition of bisphenol A

BPA-imprinted polyethersulfone (PES) microspheres for the binding and recognition of bisphenol A (BPA) were fabricated by means of a liquid-liquid phase separation technique. The imprinted novel PES microspheres had a porous structure with a skin layer, under which was followed by a finger-like structure. The recognition experiments with the BPA-imprinted microspheres were carried out by applying the microspheres to various BPA solutions. In water, high binding amounts of BPA were observed in the range of 19-42 μmol/g capacity, but the recognition was low in the BPA water solution. With the increase of the concentration in BPA solution, the binding amounts and the recognition coefficient increased. However, 1,4-butylene glycol/water media showed high recognition of the imprinted microspheres with a low binding capacity of BPA. In addtion, with the increase of the BPA amounts in the PES solution used to prepare the imprinted microspheres, the specific recognition sites increased, and the recognition ability increased. Evidence revealed that microsphere recognition was effective for BPA due to the binding to specific recognition sites [S]_(sites). The imprinted microspheres showed the selectivity for BPA in the wine including BPA and other organic compounds. Charge transfer and special cavities could be employed to explain the mechanism.     

Outdoor and accelerated weathering studies of bisphenol A polycarbonate

The influence of outdoor weathering on the degradation rate of unstabilized bisphenol A polycarbonate (BPA-PC) films is investigated and compared to the results found for indoor accelerated weathering conditions, using UV and IR spectroscopy. At the same dosage, changes in UV and IR were larger for the accelerated than for the outdoor weathered samples, this could be explained by the lower degradation temperature during outdoor exposures. The difference between outdoor and accelerated weathering is according to the IR measurement larger than according to the UV measurement. This difference is ascribed to difference in wavelength distribution between the spectra of the light emitted in the accelerated test and from the terrestrial sunlight. The larger difference for the IR results than for the UV results suggests a difference in ratio between photo-Fries rearrangements and photo-oxidation reaction between both exposures.     

Analytical methods for the determination of bisphenol A in food

Food constitutes the primary route for human exposure to bisphenol A (BPA), one of the highest volume chemicals produced worldwide. The estrogenic properties of BPA, its wide dispersive use and the recent extensive literature describing low-dose BPA effects in animals, have raised concerns about its possible adverse effects on human health. A reliable health risk assessment of BPA relies basically on its unambiguous identification and accurate quantification in food, and the aim of the present review is to give an overview of the analytical methods reported so far for the determination of BPA in these matrices. Emphasis is placed on the main strategies developed for sample treatment, which usually consists of several laborious and time-consuming steps in order to achieve the required sensitivity and selectivity. Separation, identification and quantitation of BPA is today reliably made with mass spectrometric methods, namely liquid chromatography-mass spectrometry (LC-MS) and gas chromatography-mass spectrometry (GC-MS), and thus main attention is devoted to these techniques, but other methods using LC coupled to fluorescence or electrochemical detection, as well as immunochemical methods are also covered. Recent and expected future developments are discussed.     

Importance of control of enzymatic degradation for determination of bisphenol A from fruits and vegetables

The purpose of this study was to develop an analytical method for determination of bisphenol A (BPA) from fruits and vegetables. The present method developed for extraction of BPA from samples was based on solid-phase extraction (SPE) method and solvent extraction. Recovery results in the samples spiked with a 10 ng/ml BPA [no detection (<1 ng/g) to 77%] were lower than those in the samples with a 50 ng/ml BPA (26-96%). The fact that the low recovery results were caused by BPA degradation by enzymes is found. These problems were proved by the pH (pH ≤3) and the heating treatment (at ≥80 °C for 5 min). However, because the heating treatment at temperatures of ≥80 °C for 5 min is more difficult and time-consuming method than the pH control, we suggest that the pH control is useful to prevent BPA degradation. Good recovery results (82-101%) were obtained from all fruit and vegetable samples after pH treatment (pH ≤3). Effective elimination of impurities and a good detection limit (1 ng/g) were obtained with a method involving two SPE cartridges (OASIS HLB and Sep-Pak Florisil cartridge).     

载钛羟基磷灰石光催化降解内分泌干扰物双酚A

对载钛羟基磷灰石（TiHAP）进行了透射电镜、X射线衍射、紫外-可见光谱和Zeta电位表征,并应用液相色谱-质谱技术对比了TiHAP和P25 TiO₂对环境内分泌干扰物双酚A（BPA）的吸附和光催化降解性能,探讨了富里酸和Fe³⁺对TiHAP薄膜光催化性能的影响。结果表明,TiHAP和TiO₂粉体对BPA的吸附符合Langmuir吸附等温方程,且前者吸附性能更大。TiHAP薄膜光催化降解BPA的性能优于TiO₂薄膜;富里酸和Fe³⁺对TiHAP和TiO₂薄膜光催化性能的影响趋势不同,从能带结构、电子转移和吸光性等角度分析了性能不同的原因。本结果可以为应用TiHAP降解环境内分泌干扰物提供依据。