快速流化床提升管中气固流动行为的非线性分析

对φ100mm×16m、FCC固体颗粒的快速流化床提升管内环-核流动区局部颗粒含量脉动行为进行了非线性分析,用Kolmogorov熵表征了其气固流动行为.结果表明,Kolmogorov熵沿提升管环-核流动区径向有3个显著变化区域,以此为依据将提升管环-核流动区的气固流动行为沿径向分成3个流域：单颗粒随机运动控制的核心流域;单颗粒混沌控制的过渡流域;边壁控制的环形流域.同时,从颗粒对垂直气固流动系统中气固湍动程度影响的角度,解释了Kolmogorov熵的径向分布特征及其与流动结构的关系.     

提升管内密相颗粒团的运动行为

引　言对提升管中的微观流动结构及气固微观流动行为的研究将有助于对提升管反应器特性的认识 ,并可为新型、高效流化床反应器的设计提供思路 .提升管反应器中颗粒存在严重的聚集现象 ,研究者发现[1～ 4 ] ,提升管中局部位置上固含率概率密度分布呈现双峰形式 ,双峰分别对应于低固含的稀相与颗粒密集的颗粒团 ,提升管中的微观相结构为稀相与密相颗粒团共存 .文献 [5 ]中对稀相中的颗粒的运动行为进行了定量的、详细的研究 ,作者通过对颗粒速度瞬时信号的分析 ,获得了颗粒速度概率密度分布 .提升管局部位置上颗粒速度的概率密度分布也呈现双…     

循环床提升管内轴向压力梯度和物料浓度的分布特性

以3.6m高循环床提升管内轴向不同高度测点的压力数据为基础,分析了管内轴向压力梯度的变化规律,并通过压差法对提升管内轴向物料浓度的分布特性进行了研究,得出了表观气速和物料颗粒粒径的变化对二者的影响。结果显示,提升管内轴向压力梯度沿管上升方向逐渐减小,物料浓度在轴向方向上呈上疏下密的不均匀分布趋势。增加表观气速,可以减小管内上下压力梯度的差异,改善颗粒浓度分布的不均匀程度,减小颗粒流动过程中消耗的总压降。而相对于粗大粒径颗粒,细小颗粒在提升管内流动时轴向压力梯度和浓度分布都更加均匀,整个流动过程所造成气体的总压降也相对更小。     

小型提升管反应器流动-反应耦合模拟

在提升管气固两相湍流流动模型和重油反应动力学集总模型的基础上,利用Fluent软件建立了催化裂化提升管反应器气固两相流动与反应耦合模型,对实验室小型提升管反应器进行了数值模拟,考察了气固两相的流动、传热、传质与反应过程。结果表明,提升管反应器内气固两相在轴向和径向的流动、传热与反应的分布不均匀。在入口附近。原料和催化剂温度变化显著,各组分的浓度变化剧烈,在提升管上部,变化平缓。反应器出口各组分质量分数的模拟值和实验值基本吻合。说明该模型对提升管反应器出口参数和反应结果具有较好的预测性。     

环形截面提升管内颗粒的运动行为

采用PDPA(phase Doppler particle analyzer system)及磷光颗粒示踪技术对环形截面提升管中颗粒的运动行为进行了研究。与传统提升管相比，环形截面提升管中颗粒速度分布的均匀性有所改善，其最高速度与最低速度之差变小。环形截面提升管最大速度值出现在相对径向位置φ=0.3-0．4处。与传统提升管相似，环形截面提升管内颗粒的轴向返混较严重，停留时间分布曲线存在较明显的拖尾，其中颗粒的轴向Peclet数与传统提升管也处于同一数量级范围。提升管床结构的改变并未显著改变其中气固流动的微观相结构，稀相与密相颗粒团微观两相仍然存在，这种微观相结构是造成颗粒严重返混的决定性原因：稀相中的颗粒与密相颗粒团中的颗粒分别造成了颗粒停留时间分布曲线的前峰与拖尾峰。     

大型循环流化床流动结构分析

采用双光路光纤密度探头和激光多普勒测速仪测量了内径418mm,高18m的大型循环流化床提升管和下行床中的瞬态颗粒浓度信号和颗粒速度信号.对瞬态颗粒浓度和颗粒速度的概率密度分布分析表明,下行床中存在着和提升管中不同的微观流动结构,在提升管内流动结构存在明显的两相：即颗粒团相和空穴相,两相的固含率分别为接近1-ε_mf和0.01～0.02.而在下行床中,虽然在边壁也存在着颗粒的团聚行为,但不能形成稳定的、固含接近于起始流化状态固含值的颗粒团相.这种流动结构的区别揭示了下行床中气固顺重力场运动和提升管逆重力场运动在流动机制上的差异.     

提升管中气固两相流动行为的相似特性

在15.1 m高循环流化床实验装置上对提升管内的轴向压力梯度、局部颗粒浓度和颗粒速度进行了较系统的实验测试,研究了提升管中气固两相流充分发展段在不同操作条件下流动行为的相似特性.结果表明,在(G_s /ρ_p)^1.2/U^2.0_g相近的操作条件下,上行气固两相流充分发展段的颗粒浓度、下降颗粒时均速度、絮状物颗粒浓度和出现频率在空间的分布特征基本相同.对于同一提升管内的同一气固两相流系统,只要表观气速和颗粒循环速率按(G_s /ρ_p)^1.2/U^2.0_g同步变化,不同操作条件下的上行气固两相流在充分发展段就具有相似的宏观和微观流动行为.     

提升管加床层反应器不同操作模式下的压力脉动特性

在提升管加床层反应器冷模实验装置上,分别采取零床层和有床层的操作模式,测量并分析了提升管内的压力脉动行为. 结果表明,有床层操作模式下的提升管内压力脉动标准偏差明显高于零床层操作模式;压力脉动主频零床层操作模式下主要集中于1.56?3.13和0?0.391 Hz,主要源于提升管内颗粒的脉动,有床层操作模式下为12.5?25.0和0?0.391 Hz,12.5?25.0 Hz频段主要源于提升管出口上方设置的气固分布器加流化床层对提升管内气固流动的约束及其影响下的气体脉动行为,0?0.391 Hz频段主要源于提升管段进料的不连续性及其与进料口下方提升气体的相互作用.     

提升管内气固双流体模型的计算模拟

对提升管内气固流动行为建立了k–e–kp–ep–Q 双流体模型. 利用计算软件CFX模拟了内径0. 418 m、高18 m 的提升管内的冷态气固两相流动. 模拟结果与实验数据吻合较好.     

提升管内气粒流动行为的数值模拟

采用描述密相湍流气粒流动规律的k-ε-kp-εp-Θ双流体模型对不同尺度和操作条件下的提升管内的定常流动进行了计算流体力学数值模拟，获取了各种工况下有关颗粒速度、体积分率和质量流率分布等宏观流动行为的大量信息，并与相应条件下的实验数据取得了较好的吻合。此外还通过对大量模拟数据的分析获得了提升管内宏观流动规律的综合图像。该模型描述了密相湍流气粒流动规律，预测出了描述单颗粒脉动能大小的颗粒拟温度田和表征颗粒在介观尺度上脉动大小的颗粒湍动能江在床内的分布。分析表明：不同流动参数对颗粒在微观和介观尺度上的脉动有不同程度的影响；固含率对颗粒相的脉动行为和颗粒的质量扩散行为有重要的影响。     

Hydrodynamics of a dual fluidized-bed gasifier—Part I: simulation of a riser with gas injection and diffuser

Circulating fluidized beds often apply secondary gas injections and diffusers in the riser. These strongly affect the fluid dynamics of the gas-solid flow in the system. This work is performed to study these effects in a cold flow model of an biomass gasifier. It is shown that in the diffuser there is a bulb of the suspension flow, which enhances the internal solids recirculation by a factor of 3.5. Thus, the solids hold-up and the pressure drop in the diffuser are significantly increased. The study on the effect of gas injection confirms that the solids circulation rate is more enhanced by gas injections in the lower part of the riser than in the upper part. From the investigated operating parameters, the gas flow rates and the particle diameter have the strongest effects on solids circulation and mass distribution in the riser. The effect of riser geometry properties, besides the cross-section areas and the total height, was found to be small.     

Hydrodynamics and Flow Development in a 15.1 m Circulating Fluidized Bed Riser

Hydrodynamics and flow development are studied in a long riser circulating fluidized bed reactor (15.1 m). Optic fiber probes were used for the measurement of local solids distribution. Pressure drops were also measured with pressure transducers along the riser. The flow development in the riser center is almost instant with solids holdup remaining constant and low, and particle velocity remaining high along the riser. The particle flow is firstly developed from center, and then towards the wall. The riser height is an important factor for the design of circulating fluidized bed reactors. Increasing the solid circulating rate significantly slows down the flow development process, while increases in the superficial gas velocity accelerate it.     

提升管出口T型弯头压降特性的实验分析

在大型循环流化床装置上,以FCC催化剂颗粒为实验物料,针对提升管出口T型弯头用动态压力传感器测量了操作参数和结构尺寸变化对其压降的影响,系统地分析了T型弯头的压降特性。实验结果表明T型弯头的压降与颗粒浓度呈线性关系,与入口速度（提升表观气速）呈二次方关系;T型弯头出口管截面积的减小使得压降显著增大;T型弯头盲管高度的增加可使T型弯头的压降降低,但是当盲管高度增加到一定值时,压降减小不明显。盲管高度对压降的影响是由于盲管高度的增加改变了提升管上部压力的分布,使T型弯头入口压力减小,导致T型弯头的压降降低;同时盲管高度的增加也使提升管出口区域的负压约束区长度增加。盲管所形成的负压约束区构成了对提升管出口的约束作用,T型弯头的盲管高度越大负压约束区越长,约束作用越强。     

Catalytic Ozone Decomposition in a Gas‐Solids Circulating Fluidized‐Bed Riser

Computational fluid dynamics (CFD) modeling of the catalytic ozone decomposition reaction in a circulating fluidized‐bed (CFB) riser, using iron‐impregnated fluid catalytic cracking particles as catalyst, is carried out. The catalytic reaction is defined as a one‐step reaction, and the reaction equation is modified by with respect to the particle surface area, A_p, and an empirical coefficient. The Eularian‐Eularian method with the kinetic theory of granular flow is used to solve the gas‐solids two‐phase flow in the CFB riser. The simulation results are compared with experimental data, and the reaction rate is modified by using an empirical coefficient, to provide better simulation results than the original reaction rate. Moreover, the particle size has great effects on the reaction rate. The generality of the CFD model is further validated under different operating conditions of the riser.     

Hydrodynamics in airlift loop section of petroleum coke combustor

Based on the combustion characteristics of petroleum coke, a coupled gas-solid fluidized bed combustor is proposed in this work. The overall circulating system of the fluidized bed mainly consists of a dense-phase airlift loop section and a dilute-phase riser section. In different operating conditions, the particle flow behaviors in the airlift loop section were investigated systematically by using optical fiber probe. The experimental results show that the airlift loop section can be divided into four regions, namely, the draft tube, the annulus, the bottom region and the particle diffluence region, in which the average cross-sectional solids fraction and the particle velocity are different. The overall solids fraction difference between the draft tube and the annulus provides a driving force for particle circulation flow in the airlift loop section, and the driving force increases with increasing the superficial gas velocity in the draft tube. The ratio of the particle mass flux in the annulus to that in the riser ranges from 8 to 16. The particle circular velocity in the annulus also increases with increasing the superficial gas velocity in the draft tube. Moreover, a model about the particle circular velocity is established on the basis of energy equilibrium principle.     

立管高度对严重段塞流的影响分析

随着我国对石油需求量的增加,海上油气开发越来越受到重视,并且将成为我国石油工业未来的主要增长点。在海上油气田开采过程中,经常会遇到立管系统严重段塞流问题,给安全流动保障带来严峻挑战。通过改变海洋立管高度,对立管高度对严重段塞流的影响进行了深入分析,得到了不同立管高度情况下,严重段塞流的特征参数分布规律,并分析了产生机理。研究结果对于未来海洋石油开采中的立管设计可以提供一定依据。     

Heat Transfer in the Downer and the Riser of a Circulating Fluidized Bed – A Comparative Study

The characteristics of heat transfer were studied in both a gas‐solids concurrent downflow fluidized bed (downer) and a gas‐solids concurrent upflow fluidized bed (riser) with FCC particles. The radial and axial distribution profiles of the heat transfer coefficient between a suspended surface and the gas‐solids flow suspension were obtained using a miniature heat transfer probe, under different operating conditions. Comprising the results of the heat transfer in the downer and the riser shows that there exists some significant distinction between the heat transfer processes in the two reactors. The characteristics of heat transfer in both cases are closely related to their hydrodynamics and the distinct flow structures determinate the different heat transfer behaviors. The results also indicate that the operating conditions present some different effects in the two beds.     

带有文丘里反向流动转向器的紧凑型气动式脉冲射流泵(英文)

A compact pneumatic pulse-jet pump with a Venturi-like reverse flow diverter,which consists of a nozzle and diffuser,is designed for lifting and transporting a hazardous fluid through a narrow mounting hole.The pumping performance for a liquid mixture or a liquid-solid mixture is examined in terms of the effects of liquid viscosity,particle mass concentration,lifting height,and compression pressure.Results reveal that the pumping performance of the compact pneumatic pulse-jet pump is controlled by jet inertia and the flow resistance of the riser tube positioned after the diffuser.The capacity of the compact pneumatic pulse-jet pump increases with compression pressure and decreases with liquid viscosity.However,even for a liquid mixture with a high viscosity of 7.38 mPa·s,a pumping capacity of 170.7 L·h-1 was observed.For a liquid mixture,two dimensionless indices of performance were found to be the ratio of Euler numbers Euout/EuDV and the suction factor q.As the liquid-solid mixture was lifted to elevation of 6.74 m by the compact pump,the particle size distributions of the liquid-solid mixture in the tank and from the riser tube outlet were determined by a particle size analyzer and found to coincide well.     

Comprehensive Study on the Solids Acceleration Length in a Long CFB Riser

Systematic experimental work was conducted to investigate the solids acceleration length in a 0.10 m i. d., 16 m long circulating fluidized bed (CFB) riser with fluid catalytic cracking (FCC) particles over a wide range of operating conditions. A more feasible method is proposed to determine the acceleration length from the measured axial profiles of pressure gradient (or apparent solids holdup). With this new method and large amounts of experimental results, a clear picture of the variation of the acceleration length with both solids circulating rate and superficial gas velocity is obtained. It is found that the acceleration length increases generally with increasing solids flow rate and/or decreasing gas velocity. However, the particular variation patterns of the acceleration length with operating conditions are quite different in different operation ranges. Especially under the conditions near or at the accumulative choking, the acceleration length extends rapidly with increasing solids flow rate and/or decreasing gas velocity, and sometimes takes up the whole riser height. Reasonable explanations are provided for the observed variation patterns of the acceleration length.     

提升管内气固流动行为的数值模拟

应用计算流体力学软件Fluent,对空气为连续相、固相为催化裂化反应催化剂的循环流化床提升管内的气固流动行为进行模拟。采用用户自定义函数引入颗粒与壁面的恢复系数和颗粒的镜面反射系数,对颗粒在边壁处的部分滑移运动进行描述。采用不同的计算动力学模型及参数,数值模拟了径向颗粒浓度、轴向床层压降的空间分布,以及用以描述颗粒脉动动能的颗粒温度与固含率的关系,并与文献报道的实验和数值模拟结果进行对比分析。结果表明,选取的颗粒动力学理论模型及参数、颗粒部分滑移边界条件及气固曳力模型,可计算得到合理的颗粒轴向及径向分布,验证了提升管中存在典型的径向环核流动结构和轴向压降分布。进一步分析表明固含率显著影响颗粒温度,当固含率为0.05~0.1,颗粒温度存在转折区。