利用Pr_(70)Cu_(30)晶界扩散改善烧结钕铁硼废料矫顽力的研究

钕铁硼磁体制备过程中出现的部分块体废料由于矫顽力较低,性能难以满足使用要求.本文主要通过晶界扩散技术来提高废料磁体的矫顽力.采用Pr_(70)Cu_(30)合金作为扩散介质,对烧结钕铁硼废料磁体进行了晶界扩散处理,研究了扩散温度、扩散时间和回火时间对扩散后的磁体性能的影响.结果显示,800℃下扩散3 h,磁体的矫顽力从原来的7.88 kOe(1 Oe=79.5775 A/m)提升至11.55 kOe,提升幅度为46.6%,同时剩磁没有明显降低.扩散后回火对矫顽力的提升有一定的作用.800℃下扩散4h后的磁体在500℃回火3h后,最高矫顽力可达11.97 kOe,比原磁体废料提高了51.9%,接近成品磁体的水平.显微组织分析证实了晶界扩散的作用.扩散处理后的磁体中,主相晶粒间形成了连续晶间相,起到有效的磁隔离作用,有利于矫顽力的提高.研究还发现,Pr_(70)Cu_(30)晶界扩散虽然可以使磁体腐蚀电位上升,但也会增加腐蚀电流密度,不利于磁体抗腐蚀性的改善.本文工作对于提高材料的成品率具有重要意义.     

烧结Nd-Fe-B磁体的微观结构和冲击韧性研究

对烧结Nd₁₅Fe_72-xCo_yNb_xB₈(y=0, 5;x=0, 05, 10, 15, 20, 25)永磁体的微观结构和冲击韧性及二者间的关系进行了研究.结果表明,添加Nb能够改善Nd-Fe-B磁体的微观结构,提高磁体的冲击韧性.当无Co磁体中Nb的原子百分含量为15%时,其冲击韧性达到最大;对于添加了Co的磁体,其冲击韧性的 关键词： Nd-Fe-B 冲击韧性 微观结构 晶界     

Grain boundary interdiffusion in the case of concentration-dependent grain boundary diffusion coefficient

The grain boundary diffusion in a binary system which exhibits a grain boundary phase transition is considered in the framework of Fisher's model. The kinetic law of the growth of the grain boundary phase and the distribution of the diffusant near the grain boundary are calculated. The method of determining of the concentration dependence of the grain boundary diffusion coefficient from the experimentally measured penetration profiles of the diffusant along the grain boundaries is suggested. The experimental results on Zn diffusion in Fe(Si) bicrystals, Ni diffusion in Cu bicrystals and grain boundary grooving in Al in the presence of liquid In are discussed in light of the suggested model.     

Effects of post-sinter annealing on microstructure and magnetic properties of Nd–Fe–B sintered magnets with Nd–Ga intergranular addition

We investigate the effects of post-sinter annealing on the microstructure and magnetic properties in B-lean Nd–Fe–B sintered magnets with different quantities of Nd–Ga intergranular additions. The magnet with fewer Nd–Ga additions can enhance 0.2 T in coercivity, with its remanences nearly unchanged after annealing. With the further increase of the Nd–Ga addition, the annealing process leads coercivity to increase 0.4 T, accompanied by a slight decrease of remanence. With the Nd–Ga addition further increasing and after annealing, however, the increase of coercivity is basically constant and the change of remanence is reduced. Microstructure observation indicates that the matrix grains are covered by continuous thin grain boundary phase in the magnets with an appropriate Nd–Ga concentration after the annealing process. However, the exceeding Nd–Ga addition brings out notable segregation of grain boundary phase, and prior formation of part RE6 Fe13 Ga phase in the sintered magnet. This prior formation results in a weaker change of remanence after the annealing process.Therefore, the diverse changes of magnetic properties with different Nd–Ga concentrations are based on the respective evolution of grain boundary after the annealing process.     

Effect of adding non-ferromagnetic nanoparticles to grain boundary on coercivity of sintered Nd-Fe-B magnet

In this work, we investigated the influence of additional compounds of Nd-Cu-Al, Dy-Nb-Al, Dy-Zr-Al and Nb-Cu-Al on coercivity of sintered Nd-Fe-B magnets. The additional nanoparticles with size in the range of 40–80 nm was mixed with the micrometer Nd-Fe-B powder before sintering process. The results show that the coercivity of the sintered Nd-Fe-B magnets can be improved by introducing additional nanoparticles to their grain boundaries. The improvement of the coercivity of the magnets is clearly dependent on composition and fraction of the additional compounds. While the Dy-Nb-Al, Dy-Zr-Al and Nb-Cu-Al compounds degrade the coercivity of the sintered Nd-Fe-B magnets, the Nd-Cu-Al nanoparticles considerably improve this quantity. The coercivity the sintered Nd_16.5Fe₇₇B_6.5 magnets has been enhanced about 40% by adding 3 wt% of the Dy-free compound of Nd₄₀Cu₃₀Al₃₀.     

Coercivity enhancement of HDDR-processed Nd-Fe-B permanent magnet with the rapid hot-press consolidation process

High coercivity, fully dense anisotropic permanent magnets of submicron grain sizes were produced by rapid hot-press consolidation of hydrogenation-disproportionation-desorption-recombination (HDDR) processed Nd-Fe-Co-B powders. In the hot-press process, the coercivity of the consolidated material showed a sharp minimum prior to full densification. Thereafter, it reached a value 25% higher than that of the initial powder. Scanning electron microscopy and transmission electron microscopy observations revealed that the variation in H_cJ was caused by a redistribution of Nd along the grain boundaries during hot pressing and that the high coercivity was attributable to the formation of thin, continuous Nd-rich phase along the grain boundaries.     

The Harrison diffusion kinetics regimes in solute grain boundary diffusion

Knowledge of the limits of the principal Harrison kinetics regimes (Types A, B and C) for grain boundary diffusion is very important for the correct analysis of depth profiles in a tracer diffusion experiment. These regimes for self‐diffusion have been extensively studied in the past by making use of the phenomenological lattice Monte Carlo (LMC) method with the result that the limits are now well established. However, the relationship of these self‐diffusion limits to the corresponding ones for solute diffusion in the presence of solute segregation to the grain boundaries remains unclear. In the present study, the influence of solute segregation on the limits was investigated with the LMC method for the well‐known parallel grain boundary slab model by showing the equivalence of two diffusion models. It is shown which diffusion parameters are useful for identifying the limits of the Harrison kinetics regimes for solute grain boundary diffusion. It is also shown how the measured segregation factor from the diffusion experiment in the Harrison Type‐B kinetics regime may differ from the global segregation factor.     

Coercivity enhancement of Nd−Fe−B thin film magnets by Dy buffer and capping layers

The Dy layer was inserted into the structure of SiO₂/Ti/Nd-Fe-B/Ti as the buffer or capping layer of the Nd-Fe-B layer. The insertions of Dy layers had no significant influence on the film texture with the easy axis mainly perpendicular to the film plane. The film without Dy layer gave the out-of-plane coercivity of 533 kA/m, maximum magnetic energy product (BH)_max of 245 kJ/m³. With a Dy buffer layer, the out-of-plane coercivity and (BH)_max were increased to 1074 kA/m, 291 kJ/m³ respectively. The film with Dy capping layer had a coercivity of 1035 kA/m and (BH)_max of 286 kJ/m³. Microstructure observations showed that the Nd-rich phases were evolved into grain boundaries from triple junctions by a Dy buffer layer deposition, resulting in a well magnetic decoupling of Nd₂Fe₁₄B neighboring grains. Through capping a Dy layer, the environment of grain boundaries had been improved and some Dy diffused into Nd₂Fe₁₄B phases, which contributed to the enhancement of magnetic performance.     

Coercivity and microstructure of sintered Nd-Fe-B magnets diffused with Pr-Co,Pr-Al,and Pr-Co-Al alloys

The commercial 42 M Nd-Fe-B magnet was treated by grain boundary diffusion(GBD)with Pr₇₀Co₃₀(PC),Pr₇₀Al₃₀(PA)and Pr₇₀Co₁₅Al₁₅(PCA)alloys,respectively.The mechanism of coercivity enhancement in the GBD magnets was investigated.The coercivity was enhanced from 1.63 T to 2.15 T in the PCA GBD magnet,higher than the 1.81 T of the PC GBD magnet and the 2.01 T of the PA GBD magnet.This indicates that the joint addition of Co and Al in the diffusion source can further improve the coercivity.Microstructural investigations show that the coercivity enhancement is mainly attributed to the exchange-decoupling of the GB phases.In the PCA GBD magnet,the wider thin GB phases can be formed and the thin GB phases can still be observed at the diffusion depth of 1500μm due to the combined action of Co and Al.At the same time,the formation of the Pr-rich shell can also be observed,which is helpful for the coercivity enhancement.     

The stability of triple junctions during the grain boundary diffusion process

The grain boundary diffusion in a system with triple junctions is considered in such a geometry, in which the flows of diffusing atoms meet at the triple line. The solutions of the diffusion equation is given in the frameworks of Fisher's model and under the assumption of quasi-stationary distribution of the diffusing atoms along the grain boundaries. The change of the mechanical equilibrium at the triple junction due to the increase of the concentration of solute atoms is considered. It is shown that under some circumstances the triple junction looses its stability with respect to migration in the direction to the diffusion source. The stability diagrams in the segregation-diffusivity parameter space are plotted.     

Changes of microstructure and magnetic properties of Nd-Fe-B sintered magnets by doping Al-Cu

The microstructural and magnetic properties of Al_100−xCu_x (15at%≤x≤45 at%) doped Nd-Fe-B magnets were studied. The distribution and alloying effects of Cu or Al on the intergranular microstructure were investigated by thermodynamic analysis, differential scanning calorimetery and microscopy techniques. It was observed that when the Cu content of Al_100xCu_x exceeds to 25 at%, the (Pr, Nd)Cu and CuAl₂ phases form in these magnets. The formation of (Pr, Nd)Cu phase depends on the negative formation enthalpy of (Pr, Nd)Cu and the exclusive distribution of Cu in the intergranular regions. The eutectic reaction between (Pr, Nd)Cu phase and (Pr, Nd) occurs at 480 °C, which forms the liquid phase that dissolves the (Pr, Nd)₂Fe₁₄B surface irregularities and thus increases the quantities of (Pr, Nd)-rich phase at the grain boundaries. These changes benefit the grain boundary microstructure, especially the distribution of (Pr, Nd)-rich phase, which effectively improves the intrinsic coercivity _iH_c due to the decreases of exchange coupling between the (Pr, Nd)₂Fe₁₄B grains.     

Improvement in coercivity,thermal stability,and corrosion resistance of sintered Nd-Fe-B magnets with Dy_(80)Ga_(20) intergranular addition

To investigate the coercivity,corrosion resistance,and thermal stability of Nd-Fe-B magnets,their properties were investigated at room and high temperature before and after doping with Dy_(80)Ga_(20)(at.%) powder.The coercivity of the magnets increased from the undoped value of 12.72 kOe to a doped value of 21.44 kOe.A micro-structural analysis indicates that a well-developed core-shell structure forms in the magnets doped with Dy_(80)Ga_(20) powder.The improvement in magnetic properties is believed to be related to the refined and uniform matrix grains,continuous grain boundaries,and a hardened(Nd,Dy)_2Fe_(14)B shell surrounding the matrix grains.Additionally,the doped magnets exhibit an obvious improvement in thermal stability.For the magnets with added Dy_(80)Ga_(20) powder,the temperature coefficients of remanence(α) and coercivity(β) increased to-0.106%℃~(-1) and-0.60%℃~(-1) over the range 20-100 ℃,compared to temperature coefficients of-0.117%℃~(-1)(α) and-0.74%℃~(-1)(β) in the regular magnets without Dy_(80)Ga_(20) powder.The irreversible loss of magnetic flux(Hirr) was investigated at different temperatures.After being exposed to 150 ℃ for 2 h,the Hirr of magnets with 4 wt.%Dy_(80)Ga_(20) decreased by ~95%compared to that of the undoped magnets.The enhanced temperature coefficients and Hirr indicate improved thermal stability in the doped Nd-Fe-B magnets.The intergranular addition of Dy_(80)Ga_(20) also improved the corrosion resistance of the magnets because of the enhanced intergranular phase.In a corrosive atmosphere for 96 h,the mass loss of the sintered magnets with 4 wt.%Dy_(80)Ga_(20) was 2.68 mg/cm~2,less than 10%of that suffered by the undoped magnets(28.1 mg/cm~2).     

Anisotropic rheology during grain boundary diffusion creep and its relation to grain rotation,grain boundary sliding and superplasticity

The response of periodic microstructures to deformation can be analysed rigorously and this provides guidance in understanding more complex microstructures. When deforming by diffusion creep accompanied by sliding, irregular hexagons are shown to be anisotropic in their rheology. Analytic solutions are derived in which grain rotation is a key aspect of the deformation. If grain boundaries cannot support shear stress, the polycrystal viscosity is extremely anisotropic. There are two orthogonal directions of zero strength: sliding and rotation cooperate to allow strain parallel to these directions to be accomplished without any dissolution or plating. When a linear velocity/shear stress relationship is introduced for grain boundaries, the anisotropy is less extreme, but two weak directions still exist along which polycrystal strength is controlled only by the grain boundary “viscosity”. Irregular hexagons are characterised by four parameters. A particular subset of hexagons defined by two parameters, which includes regular hexagons as well as some elongate shapes, shows singular behaviour. Grain shapes that are close to that of the subset may exhibit large grain rotation rates and have no well-defined rheology unless there is a finite grain boundary viscosity. This new analysis explains why microstructures based on irregular but near equiaxed grains show high rotation rates during diffusion creep and it provides a framework for understanding strength anisotropy during diffusion creep.     

Interactions between grain boundary and compositional domain boundary during spinodal decomposition in nanocrystalline alloys

Due to the large grain boundary (GB) volume fraction in nanocrystalline materials, interactions between GB and compositional domain boundary (CDB) play an important role in determining the nanoscale-modulated domain structures during spinodal decomposition. In the present paper, the phase field crystal model is employed to investigate the interactions between GB and CDB. Simulation results show that CDB coarsening can drive the GB migration and bring the impingement of particles with different orientations; the large volume fraction of GB can increase the dislocation volume fraction in CDBs but does not change its proportion in the whole defects number; the crossover point of the coarsening dynamic comes from the block effect of GB with large volume fraction.     

Theory of grain boundary motion during high-temperature DIGM

A theory of diffusion induced grain boundary migration (DIGM) is presented for high temperatures where volume diffusion of solute atoms out of the grain boundary is important. It is shown that due to the presence of a gradient term in the expression for the free energy of solid solution, even a relatively small discontinuity in the solute distribution across the gain boundary provides enough driving force for grain boundary migration. From the expression obtained for the grain boundary velocity the coefficient for the Ni diffusion across the grain boundaries in a Cu(Ni) polycrystal has been estimated.     

Effect of solute atoms on grain boundary sliding in magnesium alloys

The effect of solid-solution alloying on grain boundary sliding (GBS) was investigated using pure magnesium and six kinds of Mg–X (X?=?Ag, Al, Li, Pb, Y and Zn) dilute binary solid solutions with an average grain size of 10?µm. A sharp increase in damping capacity caused by GBS was observed above a certain temperature. The temperature at which a sharp increase in damping capacity occurred depended on the alloying element. The addition of Y and Ag markedly increased the onset temperature (more than 100?K) for a sharp increase in damping capacity, whereas the addition of Zn, Al and Li slightly increased the onset temperature (less than 50?K) as compared with that for pure magnesium. Tensile tests at a temperature of 423?K revealed that the higher the onset temperature, the lower the strain rate sensitivity of the flow stress. It is suggested that the former elements (Y and Ag) are more effective in suppressing GBS in magnesium alloys than the latter ones (Zn, Al and Li). The suppression of GBS was associated with low grain boundary energy, and the extent to which the energy is reduced depended on the alloying element. It was suggested that the change in the lattice parameter (the so-called c/a ratio) affects the grain boundary energy, and thus, the occurrence of GBS.     

Simultaneous enhancement in coercivity and remanence of Nd2Fe14B permanent magnet by grain boundary diffusion process using NdHx

We have successfully developed a Dy-free grain boundary diffusion process with neodymium hydride (NdH_x) alloy to the permanent magnet Nd₂Fe₁₄B powders using hydrogenation – disproportionation – desorption – recombination (HDDR) method. All the diffusion treatments were performed at 700–800 °C for various annealing time under the high vacuum with rotating diffusion method that effectively control the abnormal grain growth. The coercivities of Dy-treated Nd₂Fe₁₄B powders were varied from 9.5 kOe to 13.2 kOe but the remanence was decreased to 8.1 kG (10% reduction) depending on dysprosium hydride (DyH_x) content and diffusion treated time. However, the coercivity and remanence of Dy-free diffusion treated powder have been increased to 12.2 kOe (28.5% enhancement) and 11.1 kG (22% enhancement) at the optimal diffusion treatment (800 °C for 3 h), respectively. This unique simultaneous enhancement is to isolate the magnetic coupling between Nd₂Fe₁₄B grains by creating non-magnetic Nd grain boundaries and enhance the alignment of the Nd₂Fe₁4B hard magnetic phase, fabricated by optimal diffusion conditions.     

Significant decrease in interfacial energy of grain boundary through serrated grain boundary transition

The mechanism of serrated grain boundary formation and its effect on liquation behaviour have been studied in a wrought nickel-based superalloy – Alloy 263. It was newly discovered that grain boundaries are considerably serrated in the absence of γ?′-phase or M₂₃C₆ at the grain boundaries. An electron energy-loss spectroscopy study suggests that serration is triggered by the discontinuous segregation of C and Cr atoms at grain boundaries for the purpose of relieving the excessive elastic strain energy. The grain boundaries serrate to have specific segments approaching one {111} low-index plane at a boundary so that the interfacial free energy of the grain boundary can be decreased, which may be responsible for the driving force of the serration. The serrated grain boundaries effectively suppress grain coarsening and are highly resistant to liquation due to their lower wettability resulting from a lower interfacial energy of the grain boundary.