共查询到20条相似文献,搜索用时 804 毫秒
1.
以P123胶束作为"纳米反应器",采用水溶液法合成了Fe3O4纳米粒子.采用场发射扫描电子显微镜(FE-SEM)、X射线衍射仪(XRD)、傅立叶变换红外光谱(FTIR)和样品振动磁强计等现代化分析测试手段对产物的形貌、结构和磁性进行了测试表征.结果表明,合成的Fe3O4纳米粒子粒径大小在30~120 nm可控,它们在常温下是超顺磁性的且具有较高的饱和磁化强度.所合成的纳米铁氧体磁性材料在信息存储、生物医药和催化等领域具有重要的理论研究价值和广阔的应用前景. 相似文献
2.
高饱和磁感应强度S型NiZn铁氧体的工艺优化研究 总被引:5,自引:0,他引:5
采用化学共沉淀法,按照一定的配比合成S型NiZn铁氧体。通过对NiZn铁氧体合成工艺参数的优化,可以提高NiZn铁氧体的饱和磁感应强度。研究表明,在0~100℃的反应温度内,随着温度的升高,NiZn铁氧体的饱和磁感应强度增加;在其他条件相同的情况下,当主体反应物Fe^3 浓度增加时,NiZn铁氧体的饱和磁感应强度相应地增加;共沉淀法合成的NiZn铁氧体在1000℃烧结温度下,60~240min范围内,烧结时间为90min时,饱和磁感应强度值最大。 相似文献
3.
4.
镍锌铁氧体粉体合成新方法 总被引:7,自引:0,他引:7
本文研究了共沉淀法合成镍锌铁氧体粉料,在测定镍锌铁碳酸盐及氢氧化物溶解度曲线基础上研究共沉淀时各种因素对粉体组成及质量的确定了制备镍锌铁氧体共沉粉的工艺条件。 相似文献
5.
6.
采用水热合成法制备镍锌铁氧体粉体,以稀土元素La、Ce进行掺杂,利用SEM和XRD 等手段对样品进行表征.结果表明,La3+、Ce3+掺杂后,La3+、Ce3+离子掺杂进入镍锌铁氧体晶格后,会产生一定的晶格畸变,造成晶粒常数的增大,但对晶体的形貌影响不大.除存在少量大颗粒,立方尖晶石相Ni0.35Zn0.65Fe1.9... 相似文献
7.
8.
高能机械研磨合成尖晶石型ZnFe_2O_4铁氧体的研究 总被引:3,自引:0,他引:3
本研究通过高能机械研磨的方法直接将ZnO和αFe2O3混合粉末合成为尖晶石型ZnFe2O4铁氧体粉末。采用X射线衍射(XRD)和高分辨透射电子显微镜(HRTEM)分析不同研磨时间ZnFe2O4铁氧体形成的化学反应过程。研究发现,反应过程分阶段进行,在初始阶段(前20h),反应进行十分缓慢;而20h以后,ZnFe2O4铁氧体的合成反应开始剧烈进行,并在很短时间内完成。反应合成的ZnFe2O4铁氧体粉末的平均晶粒度小于10nm。 相似文献
9.
本文以还原铁粉、NiO、ZnO及Fe2O3为原料,利用自蔓延高温合成(SHS)法制备NiZnFe2O4预烧料,并且利用XRD图谱,Vegard定律等分析了产物结构。分析结果表明:SHS法可以制备纯度很高的NiZnFe2O4预烧料。试验发现,保温时间及粉料压坯密度均对SHS法制备的NiZnFe2O4预烧料的结构有一定的影响:随着保温时问的延长,产物的纯度提高,同时固溶体中的组元配比更接近配方比例;当粉料压坯相对密度为63%左右时,固溶体中的组元配比可达到配方比例。 相似文献
10.
轻稀土镧取代M型钡铁氧体超微粉末的合成与表征 总被引:3,自引:0,他引:3
利用溶胶-凝胶自蔓延高温合成法制备了稀土镧掺杂钡铁氧体BaLaxFe12-xO19超微粉末。讨论了起始溶液pH值、柠檬酸配比、煅烧温度等对粉末性能参数的影响。用X射线衍射仪、扫描电子显微镜和振动样品磁强计等对粉末的结构、形貌和磁学性能进行了研究。 相似文献
11.
The reaction of guanidine hydrochloride with cyanoacetaldehyde gives high yields (40-85%) of 2,4-diaminopyrimidine under the concentrated conditions of a drying lagoon model of prebiotic synthesis, in contrast to the low yields previously obtained under more dilute conditions. The prebiotic source of cyanoacetaldehyde, cyanoacetylene, is produced from electric discharges under reducing conditions. The effect of pH and concentration of guanidine hydrochloride on the rate of synthesis and yield of diaminopyrimidine were investigated, as well as the hydrolysis of diaminopyrimidine to cytosine, isocytosine, and uracil. Thiourea also reacts with cyanoacetaldehyde to give 2-thiocytosine, but the pyrimidine yields are much lower than with guanidine hydrochloride or urea. Thiocytosine hydrolyzes to thiouracil and cytosine and then to uracil. This synthesis would have been a significant prebiotic source of 2-thiopyrimidines and 5-substituted derivatives of thiouracil, many of which occur in tRNA. The applicability of these results to the drying lagoon model of prebiotic synthesis was tested by dry-down experiments where dilute solutions of cyanoacetaldehyde, guanidine hydrochloride, and 0.5 M NaCl were evaporated over varying periods of time. The yields of diaminopyrimidine varied from 1 to 7%. These results show that drying lagoons and beaches may have been major sites of prebiotic syntheses. 相似文献
12.
纳米结构WC—Co复合粉末的制备与应用 总被引:29,自引:1,他引:29
高荣根 《稀有金属与硬质合金》1999,(2):49-54
介绍了一种制备纳米结构WCCo复合粉末的方法———热化学合成法。该方法包括原始溶液制备、喷雾干燥生成化学均匀的前驱体粉末及其流化床热转化为纳米结构WCCo复合粉末。论述了制得的纳米结构WCCo复合粉末的结构、性能与应用 相似文献
13.
综述了近年来制备超细钨粉的主要生产工艺,包括高能球磨法、氧化钨还原法、钨粉氧化还原法、仲钨酸铵直接还原法、喷雾干燥法、溶胶-凝胶法、反向微乳液介导法、熔盐电解法、相转移合成法和自蔓延高温还原法等,并分析了这几种方法的优缺点和最新研究进展。 相似文献
14.
The synthesis of carnallite from the spent electrolyte of magnesium cells and a chlorine-magnesium solution is studied. The
process parameters that ensure the formation of synthetic carnallite that meet the requirements of the magnesium industry
are determined. Specifically, the synthesis temperature is 100–130°C, the initial concentration of magnesium chloride in a
solution is 290–400 g/l, the consumption of spent electrolyte is 105% of the stoichiometric composition, and the particle
size is 0.315 mm. The sequence of synthesis operations is as follows: heating of a chlorine-magnesium solution and a spent
electrolyte to 110–120°C, their mixing in a reactor, electrolyte dissolution, the evaporation of a reaction mass during agitation,
and drying. 相似文献
15.
V. B. Kul’met’eva S. E. Porozova E. S. Gnedina 《Russian Journal of Non-Ferrous Metals》2013,54(3):239-245
Technology for the synthesis of nanocrystalline zirconium dioxide powder stabilized with yttrium oxide by joint deposition is developed. This technology makes it possible to sinter ceramics based on this powder at temperatures below 1400°C. Characteristics of the zirconia powder (depending on the synthesis conditions) are investigated using X-ray diffraction, the thermal desorption of nitrogen, and electron microscopy. It is revealed that the ultrasonic (US) effect achieved when washing the gel-like powder, as well as crushing the powder after drying and calcination, make it possible to decrease the degree of its agglomeration and decrease the agglomerate size. It is established based on the data of the thermochemical analysis that a decrease in the heating rate to the isothermal holding temperature during synthesis can decrease the liability of the ceramics made from the nanocrystalline zirconia powder to zonal sintering. 相似文献
16.
17.
红外辐射在涂层生产线中的应用 总被引:2,自引:0,他引:2
结合实际,对带材涂层生产线采用红外线烘干炉的优越性加以探讨,结论,带材表面涂层烘干固化工艺中,采用红外加热干燥与其它干燥方法相比,不但具有烘道结构紧凑、干燥周期短、热效率高、调温容易等特点,且具有显著的节能效果。 相似文献
18.
19.
高炉烘炉质量直接影响高炉长寿,通过建立炉缸炉底砖衬传热模型,以1080m3高炉烘炉阶段炉缸炉底温度数据加以验证。分析了烘炉时间、烘炉温度、冷却强度等因素对冷却壁与炭砖间填料温度的影响。结果表明在0. 5m/s冷却水作用下,对于目前普遍采用的最高烘炉温度(600℃),填料最高温度仅为44℃,远低于要求的烘干温度,不能实现较好的烘炉效果。烘炉过程中需要减弱炉缸冷却甚至停水烘炉,适当提高烘炉温度,延长烘炉保温时间;停水烘炉时冷却壁最高温度仅为158℃,远低于铸铁冷却壁的安全工作温度。考虑到烘炉时热风的氧化性气氛,保证陶瓷质耐火材料严密覆盖在炉缸炉底炭砖表面,防止开炉前炭砖氧化烧损。通过插入冷却壁与填料交界面的热电偶温度分析炉缸砖衬的升温及保温,进而判断烘炉效果;并根据高炉固有的砖衬结构及设备参数,制定与高炉相匹配的烘炉制度。 相似文献