Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003     

Effect of epolene E‐43 as a compatibilizer on the mechanical properties of palm fiber–poly(propylene) composites

Composites of palm fibers and poly(propylene) (PP) were compounded in an extruder at 200°C. The composites were subsequently injection molded into standard tensile specimens for mechanical characterization. The fracture morphology of the specimens was analyzed by scanning electron microscopy. It was observed that the composite modulus increased with the increase of fiber content, indicating the existence of adhesion between PP and the much stiffer palm fibers. However, the adhesion was not satisfactory and resulted in a decrease in the composite tensile strength with fiber addition. The compatibilizer Epolene E‐43 was used to minimize this incompatibility between the wood fibers and the PP matrix. The maleated PP additive enhanced the fiber–matrix adhesion, resulting in an improvement in composite performance. Also, small fibers showed better mechanical properties than those of long fibers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2581–2592, 2004     

Poly(propylene)–poly(propylene)‐grafted maleic anhydride–organic montmorillonite (PP–PP‐g‐MAH–Org‐MMT) nanocomposites. II. Nonisothermal crystallization kinetics

The nonisothermal crystallization kinetics of poly(propylene) (PP), PP–organic‐montmorillonite (Org‐MMT) composite, and PP–PP‐grafted maleic anhydride (PP‐g‐MAH)–Org‐MMT nanocomposites were investigated by differential scanning calorimetry (DSC) at various cooling rates. Avrami analysis modified by Jeziorny and a method developed by Mo well‐described the nonisothermal crystallization process of these samples. The difference in the exponent n between PP and composite (either PP–Org‐MMT or PP–PP‐g‐MAH–Org‐MMT) indicated that nonisothermal kinetic crystallization corresponded to tridimensional growth with heterogeneous nucleation. The values of half‐time, Z_c; and F(T) showed that the crystallization rate increased with the increasing of cooling rates for PP and composites, but the crystallization rate of composites was faster than that of PP at a given cooling rate. The method developed by Ozawa can also be applied to describe the nonisothermal crystallization process of PP, but did not describe that of composites. Moreover, the method proposed by Kissinger was used to evaluate the activation energy of the mentioned samples. The results showed that the activation energy of PP–Org‐MMT was much greater than that of PP, but the activation energy of PP–PP‐g‐MAH–Org‐MMT was close to that of pure PP. Overall, the results indicate that the addition of Org‐MMT and PP‐g‐MAH may accelerate the overall nonisothermal crystallization process of PP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3093–3099, 2003     

Effects of an organic phosphorus nucleating agent on crystallization behaviors and mechanical properties of poly(propylene)

The effects of an organic phosphorus nucleating agent on the crystallization behavior and mechanical properties of poly(propylene) were investigated. As the concentration of nucleating agent increased from 0 to 0.8%, the tensile and flexural strengths of the nucleated poly(propylene) resin increased by 15%, the flexural modulus increased by 35%, the crystallization peak temperature increased by 10°C, and the nucleation density (calculated with the nonlinear Voltrra integral equation) increased by 10⁶ times. Mechanical properties increased with nucleation density. Linear equations between the mechanical properties and the logarithmic nucleation density were revealed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 297–301, 2003     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

Effects of the chemical foaming agents,injection parameters,and melt‐flow index on the microstructure and mechanical properties of microcellular injection‐molded wood‐fiber/polypropylene composites

Wood‐fiber‐reinforced plastic profiles are growing rapidly in nonstructural wood‐replacement applications. Most manufacturers are evaluating new alternative foamed composites, which are lighter and more like wood. Foamed wood composites accept screws and nails better than their nonfoamed counterparts, and they have other advantages as well. For example, internal pressures created by foaming give better surface definition and sharper contours and corners than nonfoamed profiles have. In this study, the microfoaming of polypropylene (PP) containing hardwood fiber was performed with an injection‐molding process. The effects of different chemical foaming agents (endothermic, exothermic, and endothermic/exothermic), injection parameters (the mold temperature, front flow speed, and filling quantity), and different types of PP (different melt‐flow indices) on the density, microvoid content, physicomechanical properties, surface roughness, and microcell classification of microfoamed PP/wood‐fiber composites were studied. A maleic anhydride/polypropylene copolymer (MAH‐PP) compatibilizer was used with the intention of improving the mechanical properties of microfoamed composites. The microcell classification (from light microscopy) and scanning electron micrographs showed that an exothermic chemical foaming agent produced the best performance with respect to the cell size, diameter, and distance. The polymer melt‐flow index and the variation of the injection parameters affected the properties and microstructure of the microfoamed composites. The density of the microfoamed hardwood‐fiber/PP (with a high melt‐flow index) composites was reduced by approximately 30% and decreased to 0.718 g/cm³ with an exothermic chemical foaming agent. Tensile and flexural tests were performed on the foamed composites to determine the dependence of the mechanical properties on the density and microvoid content of the foamed specimens, and these properties were compared with those of nonfoamed composites. MAH‐PP improved the physicomechanical properties up to 80%. With an increase in the mold temperature (80–110°C), the surface roughness was reduced by nearly 70% for the foamed composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1090–1096, 2005     

Effects of the molecular orientation and crystallization on film–substrate interfacial adhesion in poly(ethylene terephthalate) film‐insert moldings

A film and substrate consisting of poly(ethylene terephthalate) were adhered by means of film‐insert molding. Two injection speeds (i.e., 50 and 500 mm/s) were chosen to induce different shear rates (and molecular orientation) between the film and the substrate. Annealing was subsequently performed on these specimens at different times and temperatures to examine the extent of orientation‐induced crystallization of the substrate surfaces embedded under the film. Differential scanning calorimetry thermograms clearly indicated a shift in the position of the secondary (β) crystalline phase toward a higher temperature in specimens molded at a 500 mm/s injection speed, suggesting that a more densely packed and well‐formed crystalline structure was generated because of higher localized orientation of molecules. Polarized Fourier transform infrared spectroscopy analyses provided dichroic ratios of the 1340‐ and 1410‐cm⁻¹ wavelengths, which corresponded to the trans‐glycol conformer and the stable benzene ring, respectively. Drastic increases in the dichroic ratios were observed, especially in specimens molded at a 500 mm/s injection speed after being annealed for 1 min. This could have been caused by the reorientation of molecules fueled by residual stresses, particularly in regions experiencing high shear during molding. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effects of rosin‐type cocrystal nucleating agents on the crystallization process and the properties of polypropylene

A new kind of rosin‐type nucleating agent for polypropylene (PP), the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate, was prepared, and the effects of the nucleating agents on the mechanical and crystallization properties of PP were also studied. The results of differential scanning calorimetry and X‐ray diffraction proved that the cocrystal of dehydroabietic acid and compound alkali dehydroabietate was formed rather than a simple blend of dehydroabietic acid and single alkali dehydroabietate. When it was added to PP, the size of the PP spherulite decreased; the mechanical properties, crystallization temperature, and transparency of PP were substantially improved. Thus, the cocrystal of dehydroabietic acid, potassium dehydroabietate, and sodium dehydroabietate acted as a more effective nucleating agent for PP. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2137–2141, 2003     

Mechanical properties and morphology of PP/ABS blends compatibilized with PP‐g‐2‐HEMA

Polypropylene (PP) and acrylonitrile–butadiene–styrene blends of different composition were prepared using a single‐screw extruder. The binary blend of PP/ABS was observed to be incompatible and shows poor mechanical properties. PP‐g‐2‐hydroxyethyl methacrylate (2‐HEMA) was used as a compatibilizer for the PP/ABS blends. The ternary compatibilized blends of PP/ABS/PP‐g‐2‐HEMA showed improvement in the mechanical properties. Electron micrographs of these blends showed a homogeneous and finer distribution of the dispersed phase. The mechanical performance increased particularly in the PP‐rich blend. The 2.5‐phr (part per hundred of resin) compatibilizer was observed to bring improvement to the properties. The suitability of various existing theoretical models for the predication of the tensile moduli of these blends was examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 72–78, 2003     

Nonisothermal crystallization,melting behavior,and morphology of polypropylene/metallocene‐catalyzed polyethylene blends

The nonisothermal crystallization, melting behavior, and morphology of blends of polypropylene (PP) and a metallocene‐catalyzed polyethylene (mPE) elastomer were studied with differential scanning calorimetry, scanning electron microscopy, polarized optical microscopy, and X‐ray diffraction. The results showed that PP and mPE were partially miscible and could form some cocrystallization, although the extent was very small. A modified Avrami analysis and the Mo method were used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was homogeneous, the growth of the spherulites was three‐dimensional, and the crystallization mechanism of PP was not affected by mPE. The crystallization activation energy was estimated with the Kissinger method. Interesting results were obtained with the modified Avrami analysis and Mo and Kissinger methods, and the conclusions were in good agreement. The addition of less mPE increased the overall crystallization rate of PP. The relationship between the composition and morphology of the blends was examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1203–1210, 2004     

Mechanical,rheological, thermal,and morphological properties of blends based on poly(propylene)/poly(propylene‐co‐1‐octene)/poly(ethylene‐co‐1‐octene)

The effect of addition of propylene copolymer, produced by metallocene catalysts, on the mechanical, rheological, and morphological properties of blends based on poly(propylene) (PP) and ethylene–1‐octene copolymer (EOC) was evaluated. It was observed that the addition of 2 wt % propylene–1‐octene copolymer (POC) improved the impact strength of the EOC/PP blends. The rheological analysis indicated that the addition of propylene copolymer produced materials with improved processability. Thermal and morphological analysis showed that the POC acts as a compatibilizer on the EOC/PP blends. © 2003 Wiley Periodicals, J Appl Polym Sci 89: 1690–1695, 2003     

Stress‐induced crystallization of biaxially oriented polypropylene

The hot stretching of thick, extruded sheets at high temperatures is a very important process in the production of finished biaxially oriented polypropylene (BOPP) films with special inner structures. Through a simulation of hot stretching in the machine direction (MD) of the processing of BOPP films, it was found that at high temperatures, the stretching ratio greatly influenced the obtained crystalline structure, as observed by differential scanning calorimetry (DSC). Also, in MD hot stretching, the crystallinity increased by an average of 20%. Wide‐angle X‐ray diffraction patterns of extruded sheet samples with and without stretching confirmed the structural changes shown by DSC, and the results proved that β‐crystal modification did not occur during the MD hot‐stretching process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 686–690, 2003     

Novel preparation of poly(propylene)–layered silicate nanocomposites

We used a novel approach to prepare poly(propylene)–clay nanocomposite starting from pristine montmorillonite and reactive compatibilizer hexadecyl trimethyl ammonium bromide. The nanocomposite structure was revealed by X‐ray diffraction and high‐resolution electronic microscopy. The thermal properties of the nanocomposite were investigated by thermogravimetric analysis. An increase of thermal stability was observed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2586–2588, 2003     

Effect of vibration on crystal morphology and structure of isotactic polypropylene in nonisothermal crystallization

An experimental study on crystal structure and morphology of isotactic polypropylene (iPP) subjected to vibration was carried out on a laboratory apparatus. Crystallite size, crystal structure, and crystallinity of iPP under vibration or nonvibration were investigated through differential scanning calorimeter (DSC), wide angle X‐ray diffraction (WAXD), and polarized optical microscopy (POM). The results reveal that at high cooling rate, the crystallinity of samples under vibration decreases, and at low cooling rate it remains constant because of chain relaxation. On the other hand, the sizes of the iPP spherulites under vibration decrease as compared with those without vibration. Taking the relaxation of the iPP chain into consideration, we believe that the influence of vibration conditions on the main α‐form of the iPP crystal is rather complex. An obvious increase of β‐form content in the crystal phase results from the imposition of vibration. The results indicate that the content of β‐iPP is dependent on vibration amplitude and time. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2187–2195, 2004     

Influence of ethylene vinyl acetate on the spinnability and mechanical properties of poly(propylene)/zeolite‐Ag blend fibers

The spinnability and mechanical properties of poly(propylene) (PP)/zeolite‐supported Ag⁺ (zeolite‐Ag)/ethylene vinyl acetate (EVA) ternary blend fibers were studied. It was found that the spinning temperature of the ternary blend fibers was decreased in the presence of EVA. The addition of 2 wt % EVA substantially improved the spinnability of the blend system by enhancing its flowability. It was also found that the ternary fiber with EVA₂₈ (28 wt % vinyl acetate content) showed balanced improvement of mechanical properties by a concomitant increase in modulus and tensile strength. The improvements of spinnability and mechanical properties suggested that a core–shell structure of zeolite‐Ag/EVA₂₈ particles, with zeolite‐Ag as the core and EVA₂₈ as the shell, was formed and remained during the melt‐mixing process of the blended chips and during the course of fiber processing. EVA probably enhanced the binding between the zeolite‐Ag and the PP matrix, as made evident in SEM microphotographs. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1460–1466, 2005     

Production of polymeric membranes made of polypropylene,poly(ethylene‐co‐vinyl acetate), and poly(vinyl alcohol)

In this study, we prepared and characterized membranes containing polypropylene, poly(ethylene‐co‐vinyl acetate) (EVA), and poly(vinyl alcohol) (PVA). The production process involved blend extrusion and calendering followed by solvent extraction by toluene and water of the EVA and PVA phases. Morphology studies involving scanning electron microscopy determined the pore size distribution at the surface and in the internal regions of the membrane. The resulting membrane properties were related to the processing variables (extension rate, process temperature, and solvent extraction methods) and blend composition. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3275–3286, 2004     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Enhanced toughening of poly(propylene) with reclaimed‐tire rubber

The dynamic vulcanization of reclaimed‐tire rubber (RTR) and homopolypropylene (PP) was performed by melt‐mixing using either a sulfur crosslinking agent, maleic anhydride (MA), dicumyl peroxide (DCP), or the combination of MA and DCP, in two consecutive machines, first a two‐roll mill and then a counterrotating twin‐screw extruder. In the case of applying a sulfur crosslinking agent, it was demonstrated that the RTR/PP blend at the ratio of 30/70 had the highest impact strength. This could be attributed to the limitation of carbon black in the blend. When the combination of MA and DCP was applied, the result was higher impact strength of the blend at the same ratio. This could be attributed to not only the cohesion between the polymer chains in each phase, PP phase and rubber phase, but also the interfacial adhesion between PP and RTR chains in these two phases. For comparison, the GRT/PP blends with and without sulfur crosslinking agent were prepared as well. All these blends showed low impact strength, which was nearly the same as that of PP. The effects of different crosslinking agents on dispersion and distribution of rubber domain size, viscosity, and percentage crystallinity were also studied. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 510–515, 2004     

Blends of poly(propylene) and polyacetal compatibilized by ethylene vinyl alcohol copolymers

Polymer blends of poly(propylene) (PP) and polyacetal (polyoxymethylene, POM) with ethylene vinyl alcohol (EVOH) copolymers were investigated by differential scanning calorimetry (DSC), rheological, tensile, and impact measurements, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The PP–POM–EVOH blends were extruded with a co‐rotating twin‐screw extruder. The ethylene group in the EVOH is partially miscible with PP, whereas the hydroxyl group in the EVOH can form hydrogen bonding with POM. The EVOH tends to reside along the interface, acting as a surfactant to reduce the interfacial tension and to increase the interfacial adhesion between the blends. Results from SEM and mechanical tests indicate that a small quantity of the EVOH copolymer or a smaller vinyl alcohol content in the EVOH copolymer results in a better compatibilized blend in terms of finer phase domains and better mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1471–1477, 2003     

Nonisothermal crystallization behavior of glass‐bead‐filled polypropylene

The effects of the glass‐bead content and size on the nonisothermal crystallization behavior of polypropylene (PP)/glass‐bead blends were studied with differential scanning calorimetry. The degree of crystallinity decreased with the addition of glass bead, and the crystallization temperature of the blends was marginally higher than that of pure PP at various cooling rates. Furthermore, the half‐time for crystallization decreased with an increase in the glass‐bead content or particle size, implying the nucleating role of the glass beads. The nonisothermal crystallization data were analyzed with the methods of Avrami, Ozawa, and Mo. The validity of various kinetic models for the nonisothermal crystallization process of PP/glass‐bead blends was examined. The approach developed by Mo successfully described the nonisothermal crystallization behavior of PP and PP/glass‐bead blends. Finally, the activation energy for the nonisothermal crystallization of pure PP and PP/glass‐bead blends based on the Kissinger method was evaluated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2026–2033, 2006