聚对苯二甲酸丁二酯/聚对苯二甲酸乙二酯固态缩聚的研究

研究了聚对苯二甲酸丁二酯(PBT)/聚对苯二甲酸乙二酯(PET)共混物的固态缩聚反应,从反应动力学过程的测定结果,表明与纯PET或PBT不同,其反应速度较快,并呈超加和的相对分子质量(以特性粘数[η]表征)增长。从反应发生在液相的基本观点出发,说明温度、共混等使液相增多,将加速反应的进行,加上共混物之间的相互缩聚和酯交换,生成嵌段共聚物的结果,导致超加和效应。     

PET/PEN共混体系结构与性能研究进展

综述了国内外PET/PEN共混体系的研究进展,重点论述了PET/PEN共混体系的结晶性能相容性酯交换影响因素、结晶动力学,并对其应用前景做了展望.     

PET/LCP反应性共混物的非等温结晶动力学

采用DSC方法研究了聚对苯二甲酸乙二酯 (PET)和热致性液晶共聚酯 6 0PHB PET (LCP)体系在少量扩链剂双 (2 唑啉 ) (BOZ)存在下形成的反应性共混物的非等温结晶动力学 .结果表明反应性共混物的Avrami指数均在 3 0～ 4 5之间 ,BOZ的加入使反应共混物中PET组分的结晶速率降低 ;表明BOZ对酯交换的促进作用 ,使所生成的共聚酯中PET嵌段的数均序列长度变短 ,而使结晶在某种程度上较为困难 ,但对体系的成核和结晶生长机理无明显影响 .结果还表明 ,随冷却速率的增大结晶峰向低温方向移动     

聚(3-羟基丁酸酯)/聚氧化乙烯共混物非晶区相容性的固体核磁共振研究

用固体高分辨核磁共振碳谱方法研究了不同组成比的聚 (3 羟基丁酸酯 ) 聚氧化乙烯共混物的结晶度、非晶区的相容性和分子运动能力 .结果表明聚 (3 羟基丁酸酯 )的结晶度几乎不随组成比变化 ,而聚氧化乙烯的结晶度则随其在共混物中含量的降低而显著降低 .聚氧化乙烯的加入使得聚 (3 羟基丁酸酯 )非晶区的分子运动能力有所增强 .共混物的非晶区表现出一定的相容性 ,相容程度与共混物的组成比有关     

多嵌段聚醚-酯共混物的微相结构与血液相容性研究

本工作合成了两种性质不同的聚醚-酯多嵌段共聚物,一种是以聚对苯二甲酸乙二酯为硬链段,聚乙二醇(PEGT)为软链段的亲水性多嵌段共聚物,另一种是以聚对苯二甲酸乙二酯为硬链段,聚四亚甲基醚二醇(PTMGT)为软链段的疏水性多嵌段共聚物。将两种共聚物以一定的比例共混,制备多嵌段聚醚-酯共混物。 改变共混物的组成,研究其微相结构与血液相容性的关系。采用动态力学谱(VES)、示差扫描量热(DSC)、透射电镜(TEM)和扫描电镜(SEM)等测定共混物的微观结构,采用微球柱法评价共混物的血液相容性。实验结果表明:材料的微观非均相结构及亲水平衡是决定血液相容性的重要因素。     

PET/PEN/DBS共混物非等温结晶动力学研究

采用DSC方法, 用修正的Avrami, Ozawa, Ziabicki宏观动力学模型描述PET/PEN/DBS[PET: 聚对苯二甲酸乙二醇酯; PEN: 聚2,6-萘二甲酸乙二醇酯; DBS: 1,3∶2,4-二(亚苄基)-D山梨醇]共混物的非等温熔融结晶过程, 研究结果表明, 修正的Avrami模型能很好地描述此共混物非等温结晶过程. 冷却速率在5-20 ℃/min范围内, Ozawa方程能很好地描述初期结晶过程, 但结晶后期由于忽略次级结晶而不适宜. 由Ziabicki结晶动力学参数可知, 该共混物的结晶随着成核剂DBS含量的增加而降低, 结晶速率随着成核剂DBS含量的增加而提高. 在非等温结晶条件下, 共混物结晶同时受到冷却速率和共混物组成的影响, 与共混物非等温结晶过程的有效能垒分析结果基本一致.     

PTT/PET共混体系晶体形态与结晶性能的研究

用差示扫描量热仪(DSC)、广角X射线衍射(WAXD)和正交偏光显微镜研究了聚对苯二甲酸丙二酯(PTT)和聚对苯二甲酸乙二酯(PET)共混体系的晶体形态与结晶性能.结果表明,共混体系结晶性能与PTT的含量有关.PET的加入,使共混体系的球晶尺寸减小.球晶完善性降低.当PTT含量为40wt%～60wt%时,共混物分别出现了双重熔融峰和双重结晶峰.双重熔融峰是加热过程中熔融重结晶造成的,双重结晶峰说明不完善的晶体产生的次级结晶.     

聚碳酸酯/聚对苯二甲酸乙二醇酯共混体酯交换反应机理

用DSC,FT-IR,~1H-NMR及索氏抽提等手段研究了聚碳酸酯(PC)/聚对苯二甲酸乙二醇酯(PET)共混体的酯交换反应。研究结果表明:PC/PET共混体在熔融处理过程中有酯交换反应发生,并有共聚产物形成,酯交换反应程度可用反应产物的FT-IR谱中特征基团的吸光度之比进行表征,酯交换反应程度不仅与熔融处理条件(反应时间、温度)有关,而且还与共混体的组成比相关。酯交换反应产物经索氏抽提后,抽提产物的FT-IR分析也证实了此结果。此外,利用抽提产物的~1H-NMR分析得出了酯交换反应中形成的共聚产物的结构式,并提出了可能的反应机理。     

PET/PC共混体系结晶行为研究进展

聚对苯二甲酸乙二醇酯(PET)／聚碳酸酯(PC)合金材料是综合性能优异的工程塑料,对其结晶行为的研究,可为设计,调节及控制材料的性能提供理论基础。评述了近年来PET／PC共混体系结晶行为研究的最新工作和理论进展,包括PET／PC共混体系酯交换、相容性及结晶性的关系,退火对PET／PC共混体系结晶行为的影响,第三组分对PET／PC共混体系结晶行为的影响,PET／PC共混体系结晶动力学以及PET／PC共混体系高压结晶行为的研究。并对今后的深入研究作了展望。     

高特PET-PBT共混单丝的结构与性能

采用一定比例的聚对苯二甲酸丁二醇酯(PBT)对聚对苯二甲酸乙二醇酯(PET)进行共混改性纺制大直径单丝,通过对共混单丝的力学性能、扫描电子显微镜及热性能分析,研究了共混比例、后拉伸工艺对共混物的相容性和拉伸强度的影响.结果表明:通过PET-PBT共混,提高了单丝的勾结强度;液体冷却温度、拉伸倍率及拉伸温度是影响共混单丝...     

聚β—羟基丁酯酯／超高分子量聚氧化乙烯共混体系相容性和结晶行为

为了解决废弃塑料引起的“白色污染”问题,世界各国竞相研制开发可生物降解高分子材料,其中,有关聚β羟基丁酸酯［ｐｏｌｙ（βｈｙｄｒｏｘｙｂｕｔｙｒａｔｅ）（ＰＨＢ）］的研究尤其活跃．然而,由于商品价格较高,材料本身抗冲击性能较差、加工窗口较窄等限制...     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

Transesterification kinetics of poly(ethylene terephthalate) and poly(ethylene 2,6‐naphthalate) blends with the addition of 2,2′‐bis(1,3‐oxazoline)

The kinetics of the transesterification reaction between poly(ethylene terephthalate) (PET) and poly(ethylene 2,6‐naphthalate) (PEN) with and without the addition of a chain extender were studied with ¹H NMR. Different kinetic approaches were considered, and a second‐order, reversible reaction was accepted for the PET/PEN reactive blend system. The addition of 2,2′‐bis(1,3‐oxazoline) (BOZ) promoted the transesterification reaction between PET and PEN in the molten state. The activation energy of the transesterification reaction for the PET/PEN reactive blend with BOZ (94.0 kJ/mol) was lower than that without BOZ (168.9KJ/mol). The rate constant k took an almost constant value for blend samples with different compositions mixed at 275 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2607–2614, 2001     

Relaxation behavior of poly(ethylene terephthalate)/poly(ethylene naphthalene 2,6‐dicarboxylate) blends prepared by cryogenic blending

A method including cryogenic grinding, melt pressing from the molten state, and quenching was used to prepare blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) in which the two phases were highly dispersed. The effect of melt‐pressing times on the thermal properties and relaxation behavior of PET/PEN films were characterized with differential scanning calorimetry and dielectric spectroscopy. For short melt‐pressing times, two glass‐transition, two crystallization, and two melting peaks were observed, indicating the presence of PET‐rich and PEN‐rich phases in these blends. Longer melt‐pressing times revealed a single glass transition and a single α‐relaxation process, showing that PET–PEN block copolymers were likely to be formed during the melt pressing. The experimental findings were examined in terms of the transesterification reactions between the blend components, as revealed by ¹H NMR measurements. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2570–2578, 2002     

嵌段液晶高聚物对聚醚砜 - 聚对苯二甲酸乙二醇酯/聚对羟基苯甲酸共混物的增容作用

嵌段液晶高聚物对聚醚砜 聚对苯二甲酸乙二醇酯／聚对羟基苯甲酸共混物的增容作用张海良张雪飞王霞瑜（湘潭大学化学化工学院湘潭４１１１０５）关键词增容作用，嵌段共聚物，原位复合材料基于热致性液晶高分子（ＴＬＣＰ）的原位复合材料以其高性能及易加工等特点而得...     

In Situ fibril formation of thermotropic liquid crystal polymer in polyesters blends

Polymer blends based on poly(ethylene 2,6‐naphthalate) (PEN) and poly‐(ethylene terephthalate) (PET) reinforced with a thermotropic liquid crystal polymer (TLCP) were prepared using a melt blending process. Polymer blends consisting of conventional cheap polyester with a small quantity of expensive TLCP are of interest from an economic point of view. The shear viscosity of the TLCP and polyester blends decreased with increasing shear rate and depended on TLCP content. The lower values of the structural viscosity index for the TLCP and polyester blends were attributed to the formation of fibrillar TLCP structures having elongated fibrils in the polyester matrix. The TLCP/PEN blends exhibited long TLCP fibrils that had smaller average diameters and narrower distributions of the diameter compared with those of the TLCP/PET blends. The higher shear force and lower viscosity ratio observed may favor the in situ TLCP fibril formation in the polyester matrix. The viscosity ratio was the most crucial factor in controlling the morphology of the TLCP phase in the TLCP and polyester blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3600–3610, 2005     

利用~1H-NMR研究HDPE/PET/EVA共混体系的酯交换反应

本文在选用EVA作为HDPE/PET共混体系增容剂的基础上 ,通过双螺杆反应挤出熔融加工过程 ,促使EVA侧基上的酯基官能团与PET组分主链上的酯基在适当催化剂———有机金属化合物存在的条件下发生酯交换反应 .1H NMR结果表明 ,酯交换反应的产生在共混体系界面原位形成接枝或交联的PET EVA共聚物 ,且主要是以生成接枝共聚物的反应为主 .     

CHARACTERIZATION OF MELT-MIXED POLY(ETHYLENE-2,6-NAPHTHALATE) (PEN)/POLYCARBONATE (PC) BLENDS

ABSTRACT

Melt blending of poly(ethylene naphthalate) (PEN) and bisphenol A polycarbonate (PC) was performed without the addition of catalyst in a batch mixer at 290°C at various compositions. All the blends prepared exhibited a biphasic character and had very good mechanical properties, in some cases, even better than those of the respective pure constituents. This behavior was attributed to a copolymer formation in the mesophase, which effectively compatibilizes the system. The formation of a PEN/PC block copolymer was considered to be due to transesterification reactions between PEN and PC and was verified by extraction experiments and examination of the soluble and insoluble fractions by various spectroscopic techniques.     

聚环氧乙烷/脂肪族聚碳酸酯共混研究

本文用差热分析(DSC)和红外光谱仪(FTIR)研究了聚环氧乙烷(PEO)和新型聚合物脂肪族聚碳酸酯(PPC)共混热行为和大分子间相互作用。熔点下降方法给出 PEO/PPC 混合体系在320K 下相互作用参数为-0.46,FTIR 谱表明 PPC 大分子链和 PEO 大分子链存在较强的相互作用;PEO/PPC 共混形态随 PPC 含量增加发生了较大变化.     

聚2,5-呋喃二甲酸乙二醇酯的合成与表征

以2,5-呋喃二甲酸和乙二醇为原料,草酸亚锡为催化剂,通过直接酯化法合成了线性高分子量聚2,5-呋喃二甲酸乙二醇酯(PEF).运用红外光谱(FTIR)和核磁共振氢谱(1H-NMR)表征了该聚酯的结构;由乌氏黏度计法和凝胶渗透色谱(GPC)建立了该聚酯在一种混合溶剂体系中特性黏数和重均分子量的关系:[η]=2.82×10-6Mw0.99dL/g,25℃,苯酚-四氯乙烷(1∶1,W/W);示差扫描量热法(DSC)和热失重分析(TGA)测定了该聚酯的热转变性能,结果表明该聚酯玻璃化转变温度为84℃,熔点为211℃,起始热分解温度高于370℃,具有良好的热稳定性;运用旋转流变仪研究了PEF的流变性能,结果表明,PEF熔体属于假塑性流体,随相对分子量的减小和温度升高,其非牛顿指数增大,在高于PEF熔点20～40℃,剪切速率为2.17×10-2～1.14×102s-1时,PEF的非牛顿指数为0.85左右.