一种弱化莫尔条纹的狭缝光栅屏裸眼3D显示器

常规竖直狭缝光栅和倾斜狭缝光栅的发光二极管(LED)屏裸眼3D显示器分别存在明显的莫尔条纹和立体图像串扰等问题,为此,提出一种弱化莫尔条纹的狭缝光栅LED屏裸眼3D显示器,它由LED屏和错位非均宽透光条的狭缝光栅构成。该狭缝光栅根据LED屏黑矩阵较宽的特点,通过适当增大透光条宽度和移动透光条在其周期中的位置,来增加狭缝光栅周期结构与LED屏像素周期结构之间的差异,降低莫尔条纹中暗带的对比度,并使莫尔条纹变得稀疏,从而达到既能弱化莫尔条纹,又不会明显增加立体图像串扰的目的。制作了所提狭缝光栅LED屏裸眼3D显示器样机,获得了莫尔条纹显著弱化、无明显立体图像串扰的显示效果,验证了理论的正确性。     

用连分数定义莫尔条纹"准周期"

由两组平行周期条纹叠加而成的莫尔条纹并非严格的周期结构,其近似的周期性在数学上等价于对任意实数的最佳有理逼近.通过将两条纹周期之比近似为其连分数的各阶渐进分数,可系统性地严格定义莫尔条纹各阶"准周期"并计算其长度;实际观察到的莫尔条纹的周期,是满足非周期程度低于经验阈值的最低阶准周期.基于莫尔条纹与连分数展开之间的对应关系,可以找到一类具有严格周期性的莫尔条纹,以及一类"周期性最差"的黄金比例莫尔条纹.本文建立了莫尔条纹与实数基本性质的联系,对莫尔条纹现象的本质提供了新的理解,对所有周期叠加问题都具有普适意义.     

基于无衍射光莫尔条纹的轴锥透镜锥角测量方法

为了准确地测量轴锥透镜锥角值,根据无衍射光同心圆环间距不随距离改变的特点和莫尔条纹放大的特性,提出了一种基于无衍射光莫尔条纹的轴锥透镜锥角的测量方法。当无衍射光束经分束器分光合束后形成莫尔条纹,平移其中一束光在图像传感器上的位置,实现莫尔条纹数量的变化,通过记录不同莫尔条纹下的中心距离计算出轴锥透镜锥角。实验以锥角为0.5°的轴锥透镜作为被测对象,与CMM测量结果进行比较,该文提出的方法相对测量误差近似为0.54%,重复性为0.86″,验证了该文方法测量轴锥透镜锥角的可行性。     

高密度LED显示屏莫尔条纹抑制研究

为了抑制数码相机拍摄LED显示屏时图像中存在的莫尔条纹现象,对莫尔条纹产生的机理及其特性进行了理论分析。提出了利用多层散射膜抑制高密度LED显示屏莫尔条纹的方法。利用光学模拟程序对莫尔条纹抑制装置进行了仿真验证,对其中的关键参数进行了优化。利用优化后的莫尔条纹抑制结果在P2.5 mm 高密度LED显示样箱上进行了实验验证。实验观察结果与理论分析吻合,该装置可大幅度降低莫尔条纹的对比度,证明了方法的有效性。     

莫尔条纹分析在数字全息存储器中的应用

针对像素不匹配的数字全息存储器中出现的莫尔条纹现象,提出了利用莫尔条纹进行全息存储光路精确调整来实现像素匹配的方法.通过对CCD像面图像中莫尔条纹的周期和角度进行分析,得到光学系统需要的精确调整参数.实验中, 实现了空间光调制器和光电耦合器阵列512×512像素的1∶1像素匹配,该方法能提高读取速度并降低误码率.     

莫尔条纹分析在数字全息存储器中的应用

针对像素不匹配的数字全息存储器中出现的莫尔条纹现象,提出了利用莫尔条纹进行全息存储光路精确调整来实现像素匹配的方法.通过对CCD像面图像中莫尔条纹的周期和角度进行分析,得到光学系统需要的精确调整参数.实验中,实现了空间光调制器和光电耦合器阵列512×512像素的1:1像素匹配,该方法能提高读取速度并降低误码率.     

基于快速傅里叶变换的条纹图像处理研究

为提高船体扭转角变形测量精度,对双光栅干涉测量法产生的莫尔条纹采用快速傅里叶变换频域处理。采集不同宽度的莫尔条纹图像,分别对图像进行快速傅里叶变换,对比分析图像频谱,得到实际莫尔条纹图像的有效频率信息。分析滤波器的选择原则,选用陷波低通滤波器,去除频域图像中高频噪声,获得莫尔条纹有效信息。实验结果表明,莫尔条纹的频域处理精度远高于空域处理结果,使扭转角测量精度提高到1.2″。     

光栅周期不一致对莫尔条纹法测量扭转角的影响

为了提高用莫尔条纹法测量扭转角的测量精度,分析了光栅周期不一致对扭转角测量误差的影响。从基于莫尔条纹法测量扭转角的原理出发,论述了光栅周期不一致与测量精度的关系,讨论了引起两光栅周期不一致的两个因素,即光栅刻划误差以及两光栅栅面不平行。理论分析表明,前者是引起光栅周期不一致的主要原因。当两光栅等效周期比值β＜1.001时,在±15′的测量范围内,选择光栅周期为50 μm,莫尔条纹宽度为1 400~1 800 μm时,光栅周期不一致引起的测量误差可以控制在1.6″之内。     

浅议莫尔现象及应用

莫尔(moire)一词来自法文,含义为波动的,或起波纹.在日常生活中,当我们将两块窗纱叠在一起时形成一种不规则明暗相间的花纹,这就是莫尔条纹.现在,莫尔现象已广泛应用于科学研究和工程技术之中,莫尔条纹作为精密计量手段可用于长度,角度、振动等领域的测量.1莫尔条纹的形成将两块参数相近的透射光栅以小角度叠合,将产生放大的光栅.如图1和图2为两块光栅常数相同的光栅A和B,叠合后得到如图3所示的放大光栅即莫尔条纹.     

绝对编码光栅的相位细分及其在位移测量中的应用

提出通过光栅条纹相位的精密测量,获取光栅高精度位移信息的方法。具体方法是对光栅图像采用多码道设计,用CCD二维图像传感器获取测量段光栅图像多码道信息。对最低码道图形的周期函数序列进行傅里叶变换、基频滤波和逆傅里叶变换获得光栅截断相位分布,其余码道信息提供相位展开的级次,以此获得测量段光栅的绝对相位分布。用光刻的手段制作了实用的绝对编码光栅,基元码道的尺寸是:27.36μm用于明条纹,27.36μm用于暗条纹,最小基元码道空间周期为54.72μm,光栅长度为14008.32μm。在步长近似3μm的位移测试中,与比对的标准仪器记录值比较,标准偏差为0.2057μm,精度在亚微米量级。重复性实验表明,位置测试的稳定性为0.09μm(标准差),得到600倍以上细分的分辨力。     

Determining large step heights using zero-order interference fringe identification and an external cavity diode laser

Zero-order interference fringe identification is a powerful tool for measuring large step heights. In contrast to white light scanning interferometry, this study utilizes an external cavity diode laser as the light source. The zero-path difference point can be accurately identified by combining wavelength scanning interferometry, in which the laser wavelength is continuously changed, with single wavelength interferometry, in which the laser wavelength is fixed. The experimental apparatus is a two-arm interferometer containing the sample in the measurement arm. The step height denotes the distance between two locations of a zero-order interference fringe, which are obtained by continuously varying the length of the reference arm. The accuracy of a sample of 10 mm step height was found to be 0.33 μm.     

Chirp-free nanosecond laser amplifier for precision spectroscopy

We describe a simple method for greatly reducing optical phase perturbations in a nanosecond pulsed dye amplifier. The laser dye mix is tailored to produce a susceptibility near zero at the operating wavelength. Frequency shifts are reduced to less than 3 MHz, and frequency chirping to less than 10 MHz, without significant loss of amplified power. This technique has been used to improve the accuracy of precision far-UV wavelength measurements in H(2) to ~7 parts in 10(9).     

X射线相衬成像应用于惯性约束核聚变多层球壳靶丸检测

随着惯性约束核聚变(ICF)研究的逐步深入,尤其是氘氚(DT)燃料层球壳梯度掺杂的广泛应用,对轻物质界面的诊断需求日益增长.在北京同步辐射形貌成像站的微米CT机上利用类同轴相衬成像方法获取了三层球壳靶丸的相衬图像,最佳空间分辨率达到了2μupm,衬度达到12%;通过分析边缘增强函数和衬度传递函数之间的关系,总结出一套完整的类同轴相衬成像方法,同时将相衬成像结果与吸收成像结果对比.实验结果表明,X射线相衬成像在轻物质界面的分辨中具有明显的优势,能够广泛应用于ICF研究、医学断层扫描CT装置和生物结构等前沿科学领域.     

全息、散班、云纹干涉法的Moiré几何原理

本文阐述了全息、散斑、云纹干涉法与Moiré几何理论的相似规律,用Moiré几何理论统一解释,比拟全息、散斑、云纹干涉法并给出相应的表达式。一、引言全息、     

基于波分耦合器的光纤布拉格光栅传感器

为了实现对光纤布拉格光栅传感器的波长解调,使用普通的光纤波分耦合作为波长鉴别器件,将波长的变化转变成光强的变化,并用双路差动放大去除光源强度变化和外界干扰的影响。使用发光二极管(LED)作为光源以降低系统成本,因此使用调制光源和交流放大器对信号进行处理。实验达到约10με的应变测量分辨力和0．2℃的温度测量分辨力。是目前最廉价的光纤布拉格光栅传感器之一。     

Laser-produced plasma helium-like titanium Kα x-ray source and its application to Rayleighben-Taylor instability study

Several experiments are performed on the ShenGuang-II laser facility to investigate an x-ray source and test radiography concepts. X-ray lines emitted from laser-produced plasmas are the most practical means of generating these high intensity sources. By using a time-integrated space-resolved keV spectroscope and pinhole camera, potential helium-like titanium Kα x-ray backlighting (radiography) line source is studied as a function of laser wavelength, ratio of pre-pulse intensity to main pulse intensity, and laser intensity (from 7.25 to ～11.3× 10¹⁵ W/cm²⁾. One-dimensional radiography using a grid consisting of 5 μm Au wires on 16 μm period and the pinhole-assisted point projection is tested. The measurements show that the size of the helium-like titanium Kα source from a simple foil target is larger than 100 μm, and relative x-ray line emission conversion efficiency ξ_x from the incident laser light energy to helium-like titanium K-shell spectrum increases significantly with pre-pulse intensity increasing, increases rapidly with laser wavelength decreasing, and increases moderately with main laser intensity increasing. It is also found that a gold gird foils can reach an imaging resolution better than 5-μm featured with high contrast. It is further demonstrated that the pinhole-assisted point projection at such a level will be a novel two-dimensional imaging diagnostic technique for inertial confinement fusion experiments.     

场助InGaAsP/InP异质结半导体光电阴极的研究

本文通过对InGaAsP/InP场助异质结半导体光电阴极的材料生长、场助肖特基结的制备及阴极激活等工艺的系统研究,研制出具有较高光谱响应的半导体光电阴极,生长出优于文献报道的晶格失配率标准的材料,得到相当80年代国际水平理想因子值的场助肖特基结,用实验数据介绍提高量子效率数量级的方法和条件.研究结果表明场助异质半导体光电阴极是在红外波段很有潜力的光电发射体.     

Mercury and beyond: diode-pumped solid-state lasers for inertial fusion energy

We have begun building the Mercury laser system as the first in a series of new generation diode-pumped solid-state lasers for inertial fusion research. Mercury will integrate three key technologies: diodes, crystals and gas cooling, within a unique laser architecture that is scalable to kilojoules and megajoule energy levels for fusion energy applications. The primary near-term performance goals include 10% electrical efficiencies at 10 Hz and 100 J with a 2–10 ns pulse length at 1.047 μ m wavelength. When completed, Mercury will allow rep-rated target experiments with multiple chambers for high energy density physics research.     

Interference comparative analysis of the shape of wavefronts of incoherent light beams

A technique of interference comparative analysis of the shape of wavefronts that can be applied to incoherent light beams is proposed. The difference in the shape of the wavefronts of the incoherent light beams under study is visualized by using the moire pattern appearing upon superposition in real time of the lateralshear interferograms or their photographs. The possibility of producing the interference pattern that visualizes the difference in the shape of the wavefronts of incoherent beams with an enhanced measurement sensitivity is shown. The results of experimental testing of this technique in visualization of the difference between the shapes of the wavefronts of two light beams emitted by different lasers are presented.     

折射率介质在制栅和云纹干涉法中的应用

利用光在折射率介质中传播可以减小光波波长的性质，提出用折射率介质法制作高频全息光栅技术，使光栅频率突破理论极限２／λ；并将折射率介质应用于云纹干涉法中，当试件栅频率为６００１／ｍｍ时，虚栅频率可达到６０００１／ｍｍ，利用其±５级衍射光进行干涉，测量灵敏度由０．８３μｍ提高到０．１６μｍ。