The effect of steam treatment on MeO/Al2O3 model catalysts (Me = Ni,Co, Cu,Fe)

To study the influence of steam on the solid state reaction between MeO (Me = Ni, Co, Cu or Fe) and Al₂O3, MeO/-Al₂O₃ and MeO/-Al₂O₃ model catalysts were kept in either N₂/20% O₂ or N₂/O₂/30% H₂O at 500–1000°C. The samples were subsequently analyzed with RBS and FTIR. Surprisingly, nickel, cobalt and copper volatilized when MeO/-Al₂O₃ or MeAl₂U₄/-Al₂O₃ samples were annealed in the presence of 0.3 atm steam at 1000°C. Especially copper was found to volatilize very rapidly in the presence of steam, even at a temperature as low as 800°C. FTIR spectra of steam-treated NiO/-Al₂O₃ samples showed the incorporation of hydroxyl groups in the nickel oxide layer. This observation and an excellent agreement with thermochemical calculations support our conclusion that the volatile species are metal hydroxides. The solid state reaction of MeO with-Al₂O₃ was found to proceed at a much higher rate in the presence of 0.3 atm steam at 500–800°C, presumably as a result of an enhanced surface mobility of Me and Al ions along the grain boundaries and the surfaces of the internal pores of the-Al₂O₃ support, when steam is present.     

31-P NMR study study of acidic sites on Al2O3 and Al2O3-SnO2 after reaction with CCl2F2/H2

The surface acidic properties of two series of samples,-Al₂O₃ and-Al₂O₃-SnO₂ after reaction with CCl₂F₂/H₂ (CFC12/H₂), have been investigated by solid state high resolution CP/MAS 31-PNMR, using trimethylphosphine (TMP) as a probe molecule. It was found after reaction, that Brønsted acid sites were formed on the-Al₂O₃ surface. The longer the reaction time, the more rigidly TMP bonded to the acid sites. For the-Al₂O₃-SnO₂ system, Brønsted acid sites were also found on both the Al₂O₃ and SnO₂ surfaces after reaction of the-Al₂O₃-SnO₂ system with CFC12/H₂. The signal intensity relevant to these sites, indicates that the SnO₂ component is attached to, and therefore covers Brønsted sites of-Al₂O₃. Two types of Lewis acid site initially present on SnO₂ were not observed after reaction with CFC12/H₂.     

Preparation and Characterization of Copper Catalysts Supported on Mesoporous Al2O3 Nanofibers for N2O Reduction to N2

The gas-phase hydrogenation of benzene to cyclohexane over Ce_{1 - x} Pt _x O_{2 -} (x = 0.01, 0.02) catalyst was investigated in the temperature range 80-200 °C. A 42% conversion of benzene to cyclohexane with 100% specificity was observed at 100 °C over Ce_0.98Pt_0.02O_{2 -} with a catalyst residence time of 1.22 × 10⁴ g s/mol of benzene. The activity of the catalyst was compared with those of Pt metal, combustion-synthesized Pt/-Al₂O₃ and Pt/-Al₂O₃. The turnover frequency value of Ce_0.98Pt_0.02O_{2 -} is 0.292, which is an order of magnitude higher than those of the other Pt catalysts investigated. The kinetics of reaction and the deactivation behavior of the catalyst were studied and a regeneration methodology was suggested. The deactivation kinetics and structural evidence from XRD, XPS, TGA and H₂ uptake studies suggest that the oxidized Pt in Ce_0.98Pt_0.02O_{2 -} is responsible for the high catalytic activity towards benzene hydrogenation.     

On the Promotion of Ag/γ-Al2O3 by Cs for the SCR of NO by C3H6

The promotion of Ag/-Al₂O₃ by adding alkali metals (Li, Na, K, Cs) for selective catalytic reduction of NO with C₃H₆ was studied in this work. The activity of NO reduction was enhanced by addition of Cs to Ag/-Al₂O₃ in the presence of excess oxygen and SO₂. The stability and growth of silver oxide particles were promoted and the dispersion of silver particles on -Al₂O₃ was improved by the addition of 0.5 wt% Cs and 1 wt% Cs to 2 wt% Ag/-Al₂O₃, respectively. The results were confirmed by H₂ TPR, UV-Vis DRS, TEM, and XPS.     

Role of La2O3 in Pd-Supported Catalysts for Methanol Decomposition

Systems of Pd supported on various La₂O₃-modified -Al₂O₃ and CeO₂–Al₂O₃ catalysts were tested for catalytic methanol decomposition and characterized by means of XRD, BET, TPR, H₂-chemisorption and CO–FTIR. The addition of lanthanum significantly improved the selectivity of CO and H₂ for all the catalysts but showed a different influence on the catalytic activity in two systems. Methanol conversion decreased on La₂O₃-modified Pd/-Al₂O₃ catalysts, in line with the reduction of Pd dispersion, while the addition of La₂O₃ improved the dispersion of Pd and reinforced Pd–CeO₂ interaction for La₂O₃-modified Pd/CeO₂–Al₂O₃ catalysts, which resulted in a high production rate of CO and H₂. Thus, a synergistic effect between CeO₂ and La₂O₃ was observed on -Al₂O₃-supported Pd catalyst for methanol decomposition.     

Heterogeneous asymmetric reactions. 23. Enantioselective hydrogenation of ethyl pyruvate over cinchonine- and α-isocinchonine-modified platinum catalysts

The enantioselective hydrogenation of ethyl pyruvate to (S)-ethyl lactate over cinchonine- and -isocinchonine-modified Pt/Al₂O₃ catalysts was studied as a function of modifier concentration and reaction temperature. The maximum enantioselectivities obtained under the applied mild conditions were 89% ee using cinchonine (0.014 mmoldm^–3, 1 bar H₂, 23°C, 6% AcOH in toluene), and 76% ee in the case of -isocinchonine (0.14 mmoldm^–3, 1 bar H₂, –10°C, 6% AcOH in toluene). Since -isocinchonine of rigid structure exists only in anti-open conformation these data provide additional experimental evidence to support the former suggestion concerning the dominating role of anti-open conformation in these cinchona-modified enantioselective hydrogenations.     

Anisotropic structure analysis for cobalt oxides on α-Al2O3(0001) by polarized total-reflection fluorescence extended X-ray absorption fine structure

Anisotropic structure analyses for [CoO_x]/-Al₂O₃ (0001) and [Co₃O₄]_n /-Al₂O₃ (0001) which were derived from Co₂(CO)₈/-Al₂O₃ (0001) were performed by a polarized total-reflection fluorescence extended X-ray absorption fine structure (EXAFS) technique. Both s- and p-polarized EXAFS data revealed that the cobalt atoms of [CoO_x] were located on three-fold hollow sites of -Al₂O₃ (0001) in a monomer form and that a thin spinel structure [Co₃O₄] grew with the (001) plane parallel to -Al₂O₃ (0001).     

31P and119Sn high resolution solid state CP/MAS NMR study of Al2O3-SnO2 systems

A series of Al₂O₃-SnO₂ catalysts with the mole ratio of Al₂O₃ to SnO₂ equal to 1:1, 1 0.5, 1 0.1, 1 0.05 and 1 0.01 were characterized by³¹P NMR of adsorbed trimethyl phosphine (TMP) and¹¹⁹Sn MAS NMR spectroscopy. It was found from³¹P NMR that no Brønsted acid sites exist in these samples. Pure SnO₂ shows two different types of Lewis acid sites; in the mixed oxide samples a Lewis peak characteristic of pure Al₂O₃ is always seen, together with either one or two other Lewis peaks, depending on the Sn concentration.¹¹⁹Sn CP/MAS NMR spectra of the highest Sn-content sample show one narrow line at –603 ppm superimposed on a very broad line, indicating a strong interaction between Al and Sn oxides.     

Molybdenum nitride for the direct decomposition of NO

The physico-chemical properties of passivated -Mo₂N have been investigated. The material showed high activities for NO direct decomposition: nearly 100% NO conversion and 95% N₂ selectivity were achieved at 450C. The amount of O₂ taken up by -Mo₂N increased with temperature rise and reached 3133.9 molg^–1 at 450C; we conclude that there formation of Mo₂O_xN_y occurred. This oxygen-saturated -Mo₂N material was catalytically active: NO conversion and N₂ selectivity were 89 and 92% at 450C. We found that by means of H₂ reduction at 450C, Mo₂O_xN_y could be reduced back to -Mo₂N and the oxidation/reduction cycle is repeatable; such a behaviour and the high oxygen capacity (3133.9 molg^–1) of -Mo₂N suggest that -Mo₂N is a promising catalytic material for automobile exhaust purification.     

Catalytic behaviour and characterisation of CuO1−z(La2O3)z/2 based catalysts deposited on γ-Al2O3 and prepared in situ with 0.0 ⩽z⩽1.00, without and with addition of Pd

(CuO)_1–z(La₂O₃)_z/2 based catalysts with 0.0z1.0 supported on -Al₂O₃ have been prepared in situ and the phases formed have been identified by XRD, SEM and TEM/EDS studies. The catalyst with z=0.5 exhibited the best catalytic activity for oxidation of CO (T ₅₀=295 and 390C with degrees of conversions of 93 and 92% at 450C under rich and lean conditions, respectively) and C₃H₆ (291 and 414C; 93 and 83%) and reduction of NO (405C; 60 and 0%). This catalyst contained appreciable amounts of the perovskite phase LaAl_1–xCu_xO₃ and the enhanced catalytic properties are ascribed to the presence of this phase. Addition of Pd to this catalyst implied that the degree of conversion of NO increased and that the light-off temperatures for all involved gas species decreased. Ageing experiments revealed that LaAl_1–xCu_xO₃ decomposed and that Cu containing Pd particles were formed during this procedure which in turn deteriorated the catalytic properties of the catalyst.     

Influence of homogeneous decane oxidation on the catalytic performance of lean NO x catalysts

Extensive homogeneous gasphase reactions were observed when decane was used as the hydrocarbon reductant for the selective reduction of NO _x . The catalytic performance of a SnO₂/CoO _x /Al₂O₃ catalyst was found to be strongly dependent on the extent of the homogeneous reaction in the precatalytic volume. The effect of the homogeneous reaction on the catalytic performance also depended on whether SO₂ was present in the feed. By filling the precatalytic volume with 25–35 mesh irregularly shaped quartz chips, gasphase reaction was suppressed significantly. This methodology was used to evaluate the inherent catalytic performance of SnO₂/CoO _x /Al₂O₃ and SnO₂/Al₂O₃ catalysts with decane as a reductant. It was found that in the absence of SO₂, SnO₂/Al₂O₃ was a better catalyst than SnO₂/CoO _x /Al₂O₃, but in the presence of 30 ppm of SO₂ the latter was a far better catalyst.     

Reduction of NO by H2 on PdO-MoO3/γ-Al2O3 of low molybdena loading

The catalytic activity and selectivity of three PdO-MoO₃/-Al₂O₃ catalysts containing about 2% Pd and 2% Mo were studied for the reduction of NO by h₂ in the presence of varying amounts of oxygen at temperatures from 50 to 550 °C. The results are compared with those for PdO/-Al₂O₃, PdO-MoO₃/-Al₂O₃ containing 2% Pd and 20% Mo, and a commercial Pt-Rh catalyst. In the absence of oxygen, the conversion of NO to N₂ and N₂O is higher on the three catalysts than it is on PdO/-Al₂O₃ at 500 and 550 °C. In the presence of oxygen, the yields of N₂ and N₂O are generally lower on two of the PdO-MoO₃/-Al₂O₃ catalysts than on PdO/-Al₂O₃.     

The Preferential Oxidation of CO: Selective Combinatorial Activity and Infrared Studies

From EXAFS (extended X-ray absorption fine structure) analysis, gold was found to have mainly oxygen in its nearest coordination shell in the fresh Au/-Al₂O₃ catalyst prepared by AuCl₃ impregnation and vacuum drying at room temperature. After thermal treatment under helium, chlorine appeared within the nearest neighbors of gold and more chlorine showed up as the treatment temperature was increased from 323 to 473K. No reduced Au species was observed up to 473K under He. However, the gold became reduced during CO oxidation at 373K and above. The precursor AuCl₃ was found to deposit on -Al₂O₃ via bonding to surface hydroxyl groups. This catalyst showed nearly 100% CO conversion at 573K, but a very low activity at 373 K under the conditions used in this study. Neither the residual chlorine nor the extent of reduction can explain the low activity at lower temperatures.     

Effect of the crystalline from of Al2O3 on the interaction and sintering of large-crystal quartzite and disperse alumina

It is established that the amount of mullite and the value of the open porosity of specimens increase in the sequence -Al₂O₃(+)-Al₂O₃-Al₂O₃Al₂O₃ · 3H₂O. The apparent density and the ultimate compressive strength increase in the reverse direction. Active modifications of alumina (hydrargillite, -Al₂O₃) stimulate mullite formation, which is accompanied by an increase in the open porosity to 40% and a decrease of the mechanical strength to 8–12.5 MPa, and high (up to 12%) linear shrinkage. High-quality, dense, strong refractories can be produced in a single firing from coarse-grained quartzite and finely disperse corundum and alumina in the form of -Al₂O₃.Translated from Ogneupory, No. 10, pp. 18 – 20, October, 1994.Eastern Institute of Refractories.     

Exafs investigations of Fe-, Ni-, Co- and Cu- MoS2/γ-Al2O3 hydrodesulphurization catalyst systems

In-situ EXAFS studies have been carried out on several transition metal (T)-MoS₂ (T = Fe, Co, Ni or Cu) catalysts supported on -Al₂O₃. While Mo is present in small crystallites of MoS₂ in all the systems studied, the local sulphidic environment around the transition metal atom varies significantly with the catalytic activity. Short T-S distances (compared to the bulk sulphides) are found in the case of the Ni and Co catalysts due to the formation of the active Ni(Co)-Mo-S state. In the case of Fe, which is not a good promoter, the Fe-S distance in the catalyst is only slightly shorter than in the bulk sulphides. No such short distance is found in the Cu-MoS₂/Al₂O₃ system since Cu acts as a poison; instead only bulk sulphides are formed. Effects of the method of preparation, order of impregnation, metal loading and other factors have been examined to arrive at the conditions favourable for the formation of the active Ni(Co)-Mo-S state.Contribution No. 774 from the Solid State & Structural Chemistry Unit.     

Role of Support in Lean DeNOx Catalysis

FTIR and pulse thermal analysis were applied to investigate catalysts containing Pt (1 wt%)/Ba (17 wt%) supported on -Al₂O₃, SiO₂ and ZrO₂. The aim was to learn how the support material affects the thermal stability of barium carbonate and its activity in the reaction to bulk Ba(NO₃)₂. The lower thermal stability of BaCO₃ in alumina supported samples was found to influence the formation of barium nitrate during the NO _x storage process. Quantification of Ba(NO₃)₂ formed during NO _x storage indicated that for alumina supported catalysts only ca. 30% of barium present in the sample is involved in the storage process. The low thermal stability found for alumina supported barium nitrite excludes its role in the formation of barium nitrate during interaction of NO _x with the catalyst at 300 °C. The studies indicate that -Al₂O₃ plays a major role in influencing the thermal stability of BaCO₃ and Ba(NO₃)₂. This finding seems to be relevant for the higher activity of -Al₂O₃-supported catalysts in NO _x storage reduction reactions.     

Small Amounts of Rh-Promoted Ni Catalysts for Methane Reforming with CO2

Small amounts of Rh-promoted Ni/-Al₂O₃ catalysts possessed higher activity than pure Ni/-Al₂O₃, Rh-Al₂O₃ catalysts and exhibited excellent coke resistance ability in methane reforming with CO₂. XRD, H₂-TPR, CO₂-TPD and coking reaction (via CH₄ temperature-programmed decomposition) indicated that Rh improved the dispersion of Ni, retarded the sintering of Ni and increased the activation of CO₂ and CH₄ on the surface of catalyst.     

Reduction of NO by H2 and CO on PdO-MoO3/γ-Al2O3 of low molybdena loading

The activity and selectivity in the catalytic reduction of NO by a mixture of CO and H₂ of three PdO-MoO₃/-Al₂O₃ catalysts are compared in the presence of varying amounts of oxygen at reaction temperatures from 100 to 550°C. The catalysts were prepared by different methods and contain about 2% Mo and 2% Pd. Results are compared with those for PdO/-Al₂O₃, PdO-MoO₃/-Al₂O₃ containing 2% Pd and 20% Mo, and a commercial Pt-Rh catalyst. The PdO-MoO₃/-Al₂O₃ catalysts are more active for the selective reduction of NO to N₂ and N₂O than PdO/-Al₂O₃ under slightly oxidizing conditions at temperatures from 300 to 550°C. At these reaction conditions, the fresh PdO-MoO₃/-Al₂O₃ catalysts are comparable with a commercial Pt-Rh catalyst. The improved activity of PdO-MoO₃/-Al₂O₃ relative to PdO/-Al₂O₃ is believed to be due to the interaction between Pd and Mo. The effect of O₂ on the activity and selectivity of these catalysts is different in the reduction of NO by H₂, by CO, and by a mixture of H₂ and CO. The results using the mixture of reductants cannot be inferred from the results with the single reductants.     

Reduction of NO by CO on PdO-MoO3/γ-Al2O3 of low molybdena loading

The catalytic activity for the reduction of NO by CO of five PdO-MoO₃/-Al₂O₃ catalysts is compared in the presence of varying amounts of oxygen at reaction temperatures from 25 to 550 °C. The samples were prepared by different methods and contain about 2% of Mo and 2% Pd. Results are compared with the activities and selectivities of PdO/ -A1₂O₃ and PdO-MoO₃/-Al₂O₃ containing 2% Pd and 2% Pd + 20% Mo, respectively. All catalysts showed appreciable activity at temperatures between 300 and 550 °C and at stoichiometric ratios,R, of the oxidizing to reducing gases of 0.1 <R < 1.1. The activity of three PdO-MoO₃/ -A1₂O₃ catalysts with low concentrations of Mo and Pd was found to be significantly higher than the activity of PdO/-Al₂O₃ at 1.1 <R < 1.3 and at temperatures between 300 and 500 °C. The improved activity is ascribed to the interaction of the active metals.     

Supported Cu Catalysts with Yttria-Doped Ceria for Steam Reforming of Methanol

The steam reforming of methanol was studied over Cu/Al₂O₃ catalysts with the addition of yttria-doped ceria (YDC). The YDC-modified catalysts were prepared by impregnating a -Al₂O₃ support with Y and Ce then with Cu. The addition of YDC drastically enhanced the activity of Cu/Al₂O₃ in the methanol reforming reaction. The enhanced activity was attributed to the increase of Cu⁺ species by YDC in the methanol reforming environment. However, the addition of YDC decreased the copper dispersion. The Cu dispersion could be enhanced by adding chromium oxide. The addition of YDC and Cr where Al₂O₃ was first impregnated with Cr then with YDC showed the most pronounced enhancement of the catalyst activity. At reaction temperatures of 200250 °C, the CO concentration in the products was smaller than 0.1%.